LG Electronics 22LQ630H manual

Express Script Installer Menu Wizard pages 1 1 – 14 Custom Master TV Setup pages 15 – 18 Cloning Information pages 32 – 40 FTG Mode of Operation pages 41 – 52 EXPERIENCED INST ALLER © Copyright 2012, LG Electronics U.S.A., Inc. Hospital TVs P/N: 206-4207 (Rev C) Commercial Mode Setup Guide Note: Selected features shown within this guide ma[...]

2 206-4207 MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________ Serial No._______________ W ARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE P ARTS INSIDE[...]

3 206-4207 IMPORT ANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accor- dance with the manufacturer ’s instructions. 8. Do not install near [...]

4 206-4207 IMPORT ANT SAFETY INSTRUCTIONS (Continued from previous page) 22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, follow the precautions below . An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can com[...]

5 206-4207 T able of Contents Notes • Installer Menu content is intended for use primarily by qualied TV electronics technicians. • Refer to the Owner ’s Manual for additional information on TV installation, features, specications, maintenance, and safety instructions. • Design and specications subject to change without prior notic[...]

6 206-4207 Commercial Mode Overview This document describes how to set up LQ630H and CQ610H TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’ s CPU, Pr oto co l T rans lat or Ca rd (P TC) , or embedded b -LAN™ (EBL) module, or it resides [...]

7 206-4207 Commercial Mode Overview (Cont.) T ypical Installer Menu TV Setup Menus PICT UR E A UD IO INP UT OPT IO N TIM E MY ME DI A CHA NN EL L OC K Installer Menu T o create a customized Master TV Setup, you will need to know how to enter the commercial controller (PTC) Installer Menu and make changes to the default values as required. If necess[...]

8 206-4207 FTG Mode This mode enables Pro:Idiom ® decryption and also allows logical channel mapping of physical channels to remove the need for dash tuning. T V o pe rat ion i n F TG Mo de is ba se d o n whi ch el eme nt of t he T V own s t he FTG Lo gi cal C han ne l M ap— th e C PU or th e EBL . Und er sta ndi ng th e app lic at ion i n w hi [...]

9 206-4207 Pro:Centric TV Interactive Menu Features The in terac tive Pro:C entri c TV en ables pati ents and vi sitor s—fro m the comf ort o f the ir hos pital room s—to view a nd se lect from a com plete list ing of hosp ital servi ces a nd am enitie s. The Pro: Centri c TV i s conn ected to the hosp ital’ s billi ng co mpute r , and se rvi[...]

10 206-4207 SAP Analog Mode: Selects MTS sound (Mono, Stereo, or SAP). DTV Mode: Changes the audio language, if additional languages are available. * INFO Displays channel information. ** CC Press to activate subtitles, unless the Channel Preview/Banks Setup Menu is currently on the screen, in which case this option displays the Lock (V -Chip) Menu[...]

1 1 206-4207 Upon launching, the Express Script Installer Menu Wizard prompts you to select a menu mode. Use the Up/Down arrow keys on the Installer Remote to select the appropriate option: • Select/highlight Express Script in order to proceed with the Installer Menu Wizard. Then, press OK (Enter) on the Installer Remote. • Select/highlight Exi[...]

12 206-4207 Express Script Installer Menu Wizard (Cont.) Installer M enu Wizar d Which inputs will you be using? Step 2. Aux Input Customize Inputs. Use default values. Back Next 1 ► 2 ► 3 ► 4 ► 5 ► 6 ► 7 ► 8 OK Exit Express Script PTC: V1.00. 013 CPU: V03.07.00.01 ASIC: D279 CC Up/Down/Left/Right arrow keys Whi ch sp eake r co nfig u[...]

13 206-4207 6. Run the Auto Search (Auto T uning). Select Execute Auto Search and press OK (Enter) to start the channel scan (searches for all available analog and digital channels). The system will display progress of the channel scan in a pop-up window . The scan typically takes a few minutes. When th e cha nnel scan is co mplet e, pre ss OK (Ent[...]

14 206-4207 • Icon: Us e t he Le ft/ Ri ght a rro w k ey s o r key in t he ic on nu mbe r t o sel ec t t he app rop ri ate t rad em ark /ic on fo r eac h c ha nne l’ s Ch an nel -T ime on- sc ree n dis pla y . Ico ns ar e a va ila bl e f or fa mil ia r c ha nne ls, s uch a s ABC , CBS , NBC , e tc . I de nti a ble ic on s s ho uld en ab le t[...]

15 206-4207 Custom Master TV Setup Clonable TV Setup Menu Features Notes: • Some menu options vary between analog and digital channels and Aux inputs. • The end user only has access to features that are available on the pillow speaker or the user remote control if provided by the institution. Before Y ou Begin • It is recommended that you dis[...]

16 206-4207 Set the TV features to the desired configuration for the end user . PICT URE A U DI O INP UT OPT IO N TIM E MY ME DIA CHA NN EL L OC K Audio Menu Note: Audio Menu options are inaccessible (grayed out) if TV Speaker is not selected (i.e., Pillow Only is selected). Lock Menu Note: Press 0-3-2-5 to access the Lock Menu if the Lock System i[...]

17 206-4207 (Continued from previous page) 3. (Optional) Run Auto T uning. Note: If you intend to use a USB memory device / .tlx file for cloning purposes, DO NOT run Auto T uning. If you T each a .tlx file with an auto-tuned/edited Channel Map to a T arget TV , this will put the T arget TV in FTG Mode via CPU. Proceed to step 6 to verify the TV se[...]

18 206-4207 Custom Master TV Setup (Cont.) After verifying the TV Setup, set Installer Menu item 028 CH. OVERIDE to 000.* DIGIT AL 19-3 WXYZ MONO STEREO SAP Custom T ext Label “WXYZ” created in 2-5-4 + MENU Mode. 5. (Optional) Add Custom Channel and Aux Input Labels: 2-5-4 + MENU Mode Note: 2-5-4 + MENU Mode enables you to add/edit channel icon[...]

19 206-4207 Installer Menu Use the Installer Menu to set up, change, or view operational settings. Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing. T ypical Installer Menu Accessing the Installer Menu 1. Make sure the TV is ON. 2. Using an I nstal ler R[...]

20 206-4207 Menu Item Function V alue Range Default V alue Brief Description of Function 000 INST ALLER SEQ 0 ~ 3 0 Leave default set to 0. 001 POWER MANAGE 0 ~ 7 0 Sets number of hours of no activity before automatic shutoff. 002 AC ON 0 / 1 0 Set to 1 to enable Auto T urn ON when AC power is applied. 003 BAND/AFC 0 ~ 3 1 Selects Tuning Band: 0=Br[...]

21 206-4207 Installer Menu (Cont.) Installer Menu Items 071 through 122 Menu Item Function V alue Range Default V alue Brief Description of Function 071 BCK. CH-TIME 0 ~ 7 2 Chooses custom background color for the Channel-Time display . 073 CH NOT A VBLE 0 / 1 0 If set to 1 and item 028 CH. OVERIDE is set to 0, “NOT A V AILABLE” message is disp[...]

22 206-4207 Detailed Descriptions of Installer Menu Items 000 - INST ALLER SEQUENCE Species entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy . If set to 0, Power Management is[...]

23 206-4207 012 - IR BANKS EN (IR Banks Enable) For di rec t a cce ss to a par tic ula r c han nel b ank . W hen en abl ed, y ou can ac ces s a ch ann el ba nk by inp utt ing th e dis cre te IR cod e f or tha t b ank . Not e: This item is not available in the Installer Menu when item 027 HOSPIT AL MODE is set to 0. 013 - SCAN MODE (Functional after[...]

24 206-4207 Installer Menu (Cont.) When Hospital Mode is set to 0 (disabled), both the IR code that will control the TV and the speaker selection depend on the Installer Menu item 020 FEA TURE LEVEL setting. Note: The defau lt s etti ng ( 254) is not sele ctab le i n the Ins tall er Menu . If you ever nee d to res tore the def ault sett ing, you mu[...]

25 206-4207 079 - UPN MSB-1 (UPN Most Signicant Byte-1) User programmable number , most signicant byte-1 readable by MPI command. Note: Not linked to serial number . 080 - UPN MSB-2 (UPN Most Signicant Byte-2) User programmable number , most signicant byte-2 readable by MPI command. Note: Not linked to serial number . 081 - UPN LSB (UPN[...]

26 206-4207 106 - ASP RA TIO LOCK (Aspect Ratio Lock) Set to 1 to retain previous aspect ratio with power off. Set to 0 to retain default aspect ratio with power off. See item 096 DEF . ASP . RA TIO above. 1 16 - VIDEO MUTE EN (Video Mute Enable) Set to 0 for Normal. Set to 1 for Blank. 1 17 - F ACT DEF AUL T (Factory Default) Set to 0 for norma l.[...]

27 206-4207 Channel Icons / Custom T ext Labels (2-5-4 + MENU Mode) Changing Channel Icons and/or Adding or Editing Custom T ext Labels in the Channel-Time Display If there is no pre-assigned icon for a channel, you can add a custom text label of up to seven (7) characters to help identify the channel or network. Also, if desired, a custom text lab[...]

28 206-4207 C HA NN E L P R E V I E W - B A N K 1 C H 01 1- 0 0 1 NO RM A L -A DD ED E nt er - > Ch a ng e C C -> V CH IP M e n u , C h . P r e v i e w - > Ex i t Channel Banks Setup Channel Banks Overview Channel Banks enable institution administrators to create tiered channel programming on patient in-room TVs. Each channel bank may offe[...]

29 206-4207 Channel Banks Setup (Cont.) T ypical Channel Previ ew/ Ban ks Setup Menu C H A N N E L P R E V I E W - B A N K 1 C H 0 1 1 - 0 0 1 N O R M A L -AD DED E n t e r - > C ha n g e C C - > V C H I P M e nu , C h . Pr e v i e w - > E x i t IDs currently selected channel bank. IDs currently selected channel. IDs channel status in sele[...]

30 206-4207 Channel Banks Setup (Cont.) Channel Banks Worksheets Use Chan nel Bank s Wo rks he ets (see foll owi ng pa ge) to crea te cha nn el st atu s cha rts as part of the set up pro ces s. On the cha nne l sta tus char ts, show the sta tus for eac h cha nne l in all chan nel bank s. T his then bec ome s the pati ent ente rta in men t pro gra m[...]

31 206-4207 Date _____________ Installer _____________________________________ Page ___ of ____ Location ______________________________________________________________________ Channel Banks W orksheet B A N K Channel Number 1 2 3 4 B A N K Channel Number 1 2 3 4 B A N K Channel Number 1 2 3 4 B A N K Channel Number 1 2 3 4 B A N K Channel Number 1 [...]

32 206-4207 Cloning Overview Cauti on: Do not unplu g the TV p ower cord o r rem ove/d iscon nect the U SB mem ory d evice / clone progr ammer whil e Lea rning or T eaching, as d oing so ma y caus e the TV t o mal funct ion or ha rm the USB devic e/clo ne pr ogram mer , resp ective ly . IMPORT ANT CLONING INFORMA TION There are four different proce[...]

33 206-4207 USB Cloning Procedures Learning / T eaching a Master TV Setup using a USB Memory Device / .tlx File USB Cloning Notes • Read the IMPORT ANT CLONING INFORMA TION on page 32 before beginning any cloning procedures. In particular , ensur e tha t t he Ma st er T V Set up do es no t c on tai n a C han ne l M ap ; o the rw ise , T eac hin g[...]

34 206-4207 USB Cloning Procedures (Cont.) Learning / T eaching a Master TV Setup using a USB Memory Device / .tlx File (Cont.) T each Master TV Setup to T arget TV 1. Ensure the T arget TV is in Pass-through Mode, and then use the Installer Remote to enter the T arget TV Installer Menu: Press MENU repeatedly until the on-screen display of the TV s[...]

35 206-4207 USB Cloning Procedures (Cont.) Learning / T eaching a Master TV Setup using a USB Memory Device / .tll File Learn Setup from Master TV 1. Ensure the Master TV is set up completely . 2. Plug the USB memory device into the USB IN port on the Master TV . 3. Press MENU on the Installer Remote to display the TV setup menus, use the arrow nav[...]

36 206-4207 T each T o TV UPDA TING... Do n ot rem ove the US B fr om the por t! Do not unplug! 50% USB Cloning Procedures (Cont.) Learning / T eaching a Master TV Setup using a USB Memory Device / .tll File (Cont.) T each Master TV Setup to T arget TV 1. On the T arget TV , if ne cessa ry ex it th e Exp ress Script Inst aller Menu Wizard , and the[...]

37 206-4207 Clone Programmer Cloning Procedures Learning / T eaching a Master TV Setup using a TLL-1 100A Clone Programmer Caution: If the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will damage the clone programmer . Antenna or CA TV [...]

38 206-4207 Clone Programmer Cloning Procedures (Cont.) Learning / T eaching a Master TV Setup using a TLL-1 100A Clone Programmer (Cont.) (Optional) Set the Clock Set the time on a Master TV’s clock. (If the time has already been copied from a TV into the TLL-1 100A clone programmer , you can set the Master TV’s clock by copying the time from [...]

39 206-4207 Clone Programmer Cloning Procedures (Cont.) Learning / T eaching a Master TV Setup using an L T2002 Clone Programmer Ferrite Core (TDK, ZCAT 2035-0930) Antenna or CA TV QuickSet II Programmer L T2002 ® ZENIT H ELE CTRONI CS C ORPOR AT ION, LINC OLNSH IRE, ILLIN OIS, USA • heartbeat power on communications ok • slow power on no comm[...]

40 206-4207 Clone Programmer Cloning Procedures (Cont.) Learning / T eaching a Master TV Setup using an L T2002 Clone Programmer (Cont.) (Continued from previous page) Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will be displayed on the screen while the L T2002 copies the Master Setup. When the Learning process is complete, [...]

41 206-4207 FTG Mode via CPU This mode provides the following features: • Logical channels mapped to RF delivered content. • Digital RF channel minor (program) numbers up to 999. • FTG Channel Map of up to 600 logical channels. • Start Channel set for RF or Aux input delivered content. • Pro:Centric data delivery over RF . FTG Mode via CP[...]

42 206-4207 FTG Mode of Operation Overview (Cont.) PICT UR E A UD IO INP UT OPT IO N TIM E MY ME DI A CHA NN EL L OC K TV Setup Menus Shows that the TV is in Pass-through Mode . Function Menu Indicates the TV is not in Pass- through Mode . While the TV is in this mode, Installer Menu settings can be accessed as read-only . ABC ASP ECT RA TIO Ent er[...]

43 206-4207 FTG Mode via CPU Creating an FTG Conguration File using the FTG File Manager This section describes how to create an FTG Conguration (.tlx) le that can be saved to a USB memory device. In order to enable Pro:Idiom decryption, it is recommended that you create an FTG Conguration le using the FTG File Manager . Notes: • F[...]

44 206-4207 FTG Mode via CPU (Cont.) (Continued from previous page) Note: T o remov e an indiv idual item from the FTG Co ngur ation List or t he TV S etup Menu List, click on/ highli ght t he it em to be r emove d, and then clic k the Remo ve Ite m but ton d irect ly ab ove th e app licab le “List” wind ow . T o clea r bot h the curr ent F [...]

45 206-4207 1. Plug the U SB me mory device that cont ains the F TG Co ngura tion le i nto th e T arget LQ6 30H o r CQ6 10H TV USB I N port . 2. Press MENU on the Installer Remote to display the TV setup menus (TV is in Pass-through Mode) or the Function Menu (TV is already in FTG Mode). 3. Use t he ar row na vi gat io n k eys t o s el ect /h[...]

46 206-4207 1. Plug a USB memory device into the USB IN port on the TV . 2. Press MENU on the Installer Remote to display the TV setup menus (TV is in Pass-through Mode) or the Function Menu (TV is already in FTG Mode). 3. Use t he ar row na vi gat io n k eys t o s el ect /h igh lig ht ei th er th e O pti on menu icon from the TV setup menus or the[...]

47 206-4207 FTG Mode via CPU (Cont.) T ypical Installer Menu Note: The Installer Menu header will vary depending on the TV you are setting up. Set Installer Menu Items These steps provide specic instruction only on the Installer Menu items that should be set on an LQ630H or CQ6 10H TV . Refer to pages 19 to 26 for detailed information on all Ins[...]

48 206-4207 FTG Mode via EBL (Local Conguration) 1. Install (if necessary) and launch the FTG Device Configuration Application (v5.0.0 or higher) on the PC that will be used to configure the EBL. 2. Build an FTG Channel Map using the FTG Channel Map Editor in the FTG Channel Map Configuration Utility (or , if applicable, open an existing FTG Con[...]

49 206-4207 Note: The data referenced in the FTG Conguration List is only a snap- shot of the current FTG Channel Map and FTG Installer Menu settings when copied to the list. If you make any change(s) to the current data to be included in the FTG Conguration List, you will need to recopy Channel Map and Installer Menu settings to the FTG Con?[...]

50 206-4207 FTG Channel Map Conguration Utility The FTG Channel Map Configuration Utility enables you to create, view , edit, and print a Logical Channel Map. PRINT MAP Click to display a printable FTG Channel Map Report. The report can also be exported as an HTML or T ext file. EDIT/ADD MAP Cli ck to ope n the FTG Cha nne l Map Edi to r to crea[...]

51 206-4207 FTG File Manager Utilities Overview (Cont.) DELETE Click to remove highlighted channel from FTG Channel Map. ADD After defining a new Logical Channel, click to add channel to the FTG Channel Map. FTG Channel Map Editor The FTG Channel Map Editor shows a single Logical Channel’s data and the FTG Channel Map. EXIT Click to exit editor a[...]

52 206-4207 FTG File Manager Utilities Overview (Cont.) CONFIGURA TION SETTINGS Select tabs for categories of Installer Menu items to set up TV . FTG Installer Menu Conguration Utility Note: The Pro:Centric tab enables you to set up Pro:Centric-specic parameters. Refer to the Free-To-Guest (FTG) File Manager User Guide for further information[...]

53 206-4207 Reference: Upgrading TV/PTC Software using a USB Memory Device Checking the Software V ersions Y ou can check the software versions of the TV by accessing the Installer Menu with the Installer Remote: Press MENU repeatedly until the on-screen menu display no longer toggles, and then, press 9 - 8 - 7 - 6 + OK (Enter) . When you are finis[...]

54 206-4207 Re fe r en ce : D o wn lo a di n g a S pl a sh S c re en us i ng a US B M em o ry D e vi c e Splash Screen Image File Guidelines • The splash screen image must be a baseline (not progressive) 24-bit JPEG. • The image should be no larger than 1 MB. • The ideal resolution of an image for the 26/32LQ630H is 1366 x 768 pixels (HD) or [...]

55 206-4207 Reference: Power Consumption Settings Note: V alues are results of controlled experiments under laboratory conditions. The following tables assume that Installer Menu item 1 18 POWER SA VINGS is set to 3 (default) and Installer Menu item 099 BACK LIGHTING is set as shown below (default value for LQ630H TVs is 255; default value for CQ61[...]

56 206-4207 Reference: TV Aux Input Conguration DIRECT ACCESS T uning TV ENABLE MPI DA T A ST ART AUX SOURCE ASSIGN- MENT Installer Menu MPI DA T A ST A TUS TYPE 0x41 SOURCES ENABLED (R/W) DA T A ST A TUS TYPE 0xD2 CURRENT A V SOURCE (R) DA T A ST A TUS TYPE 0x0D AUX SOURCE (R) OLD_ OCV = 0 OLD_ OCV = 1 Source Input Source Mode Number Labeling V[...]

57 206-4207 A b -LAN enabled head end device, such as an LG FMA-LG101, broadcasts over the RF distribution system to communicate to multiple TVs. When the TV is first installed, it must be turned ON in order for its embedded b -LAN module to receive communication from the head end device. At this point, if it is desired for the b -LAN module to alw[...]

58 206-4207 Reference: LQ630H/CQ610H Hospital Operations Hospital Features The following table identies when and how the LQ630H and CQ610H hospital features are supported in three different TV congurations. As indicated in the introduction to this document, LG commercial TV functionality is based on “ownership” of the Channel Map. For the[...]

59 206-4207 Note: Even if Scan Mode is enabled, the front panel channel keys cannot be used to turn ON the TV . Note: The power indicator on the front panel of the TV has two dif ferent settings: one for when the TV is in standby and one for when the TV is turned ON. The Power Indicator option in the Option Menu enables you to dene the behavior [...]

60 206-4207 This section describes how to reset factory defaults either on a single TV that is currently in Pass-through or FTG Mode or on multiple TVs that are currently in FTG Mode. Note: If the TV(s) is/are currently in FTG Mode, restoring the factory defaults also resets the TV to Pass- through Mode. Installer Menu Item 1 17 F ACT DEF AUL T If [...]

61 206-4207 OPT IO N En te r Mo ve Reference: TV Zone Restrictions Close 1 ► ► The FT G Cha nn el Ma p E dit or in t he FTG F ile M ana ge r ’ s F TG Ch an nel Ma p Con g ura tio n Uti li ty en abl es you to a ssi gn Zo ne re str ic tio ns to ch an nel s tha t may be d eem ed un sui ta ble f or ce rta in lo cat io ns, f or exa mpl e, a ho [...]

62 206-4207 Reference: 22LQ630H Rear and Side Jack Panels PIL LO W SP EA KE R RGB I N (P C) ANTENNA IN TV -LIN K CFG AUD IO I N (RG B/ DV I) S PE AK ER OUT (8 Ω) CPU S ER V IC E (SE R VI CE O NL Y) PTC S ER V IC E (SE R VI CE O NL Y) GAM E CO NT RO L / MPI /DVI IN IN 1 2 USB IN AUDIO/VIDEO AV IN .......... .......... RE S E T UP D A TE AUDIO IN (R[...]

63 206-4207 Reference: 26/32LQ630H Rear and Side Jack Panels USB IN AUDIO IN (RGB/DVI) AV IN (AUDIO/VIDEO) RGB IN (PC) /DVI IN 1 IN 2 SP E AK ER OU T 8 GA M E CO N TR O L / MPI PI L LO W SP E A KE R TV -L I NK CF G PTC SERVICE (S E R VI C E O NL Y) CPU SERVICE (S E R VI C E O NL Y) ANTENNA IN .......... .......... RES ET UPD A TE HDMI/DVI IN Connec[...]

64 206-4207 L/MONO-AUDIO-R IN Connect to audio output jacks on external device. For only mono audio output, connect to Left audio input. Reference: 42CQ610H Rear and Side Jack Panels ANTENNA IN A V IN L / MON O R AUDIO VIDEO USB IN PILLOW SPEAKER RS- 23 2C I N (S E R VI C E O N L Y) AUD IO I N (RG B/ DV I) RE S ET UP D A TE PTC S ER VIC E ( S E R V[...]

65 206-4207 Reference: Pillow Speaker Setup The pillow speaker will only be functional after the Express Script/Custom Master TV Setup and cloning procedures are complete. Note: When Inst aller Menu item 027 HOSPI T AL MODE is s et to 254 (facto ry de fault valu e), t here is no power (volt age) suppl ied t o the pill ow spe aker . 1 2 3 4 5 6 3 1 [...]

66 206-4207 Reference: USB Media Navigation using Pro:Centric Pillow Speaker The Pr o:Cen tric pillo w spe aker is cu rrentl y the only pill ow sp eaker that enabl es us ers t o naviga te an d pla y/vie w USB medi a le s (vid eos, music , pho tos, etc.) . This secti on pr ovides a brie f ove rview of t he Pr o:Cen tric pillow spea ker n aviga ti[...]

67 206-4207 General Guidelines: Choosing a Location for Installing a VESA Standard Mount T o the right are some examples of VESA standard mounts. Since there are numerous types of stands and mounts available, only a few are shown here. Refer to the instruc- tions provided with the TV stand that will be used to mount the TV . Be sure the style of st[...]

68 206-4207 T roubleshooting General T roubleshooting (Some Quick and Easy T ips for Resolving Problems) Installation Cannot direct enter channel number . (TV in Pass-through Mode) Installer Menu item 028 CH. OVERIDE is set to 0, i.e., disabled and/or Channel Access was denied in Express Script. If the channel lineup is locked (recommended setting)[...]

69 206-4207 Controller Quick Check ST A TUS LED on PTC Board blinking? Plug into AC Power outlet. TV connected to AC Power? Bad TV Y es No No Y es Cycle the power by removing and reconnecting the AC Power cord. Then, observe POWER LED on front of TV . POWER LED lit? * No Y es Press POWER on Installer Remote. TV responded? No Y es TV responded? No Y[...]

70 206-4207 TV turned ON? Y es No Press POWER on Installer Remote. TV is not in Commercial Mode. Call T echnical Support for assistance. TV is in Commercial Mode. No On-screen menu display no longer toggles? Y es Press MENU repeatedly as if to access the Installer Menu. Function Menu on display? Leave the TV set ON, and press MENU on the Installer [...]

71 206-4207 Cautio n: If the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will damage the clone programmer . Reset Clone Programmer After Static Shock Aft er re pla ci ng ex hau ste d bat te rie s ( L T2002 o nly ), or if t he cl one pr[...]

72 206-4207 Channel Previe w/B ank s Setup Menu C H A N NE L P RE V IE W - B AN K 1 C H 0 1 1- 0 01 N OR M AL - A DD ED E n t e r - > C h an g e C C - > V CH I P M e n u , Ch . Pr e vi e w - > E x it Symptom Possible Cause Possible Solution Cannot change channel status in menu. Channel Access was denied in Express Script and/or Installer M[...]

73 206-4207 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider . The end looks like a hex-shaped nut with a wire through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV . 300 TO 75 OHM ADAPTER A small device that connects a 2-wire 300 ohm antenna to a 75 ohm RF jack. It is usually [...]

74 206-4207 Document Revision History / Notes Notes Document Revision History Date Description February 2012 Revision A: New document February 2012 Revision B: Additional USB port for 26/32LQ630H March 2012 Revision C: CQ610H information added Product documentation is available online at: www .LGsolutions.com/products . From the Products page, sele[...]

206-4207 Revision C © Copyright 2012, LG Electronics U.S.A., Inc. For Customer Support/Service, please call: 1-888-865-3026 www .LGsolutions.com Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a trademark of LG Electronics U.S.A., Inc. b -LAN is a trademark of LodgeNet Interactive Corporation. All other trademarks or [...]