LG Electronics 26LT670H manual

Automated Installation Routine Wizard pages 1 1 – 13 Custom Master TV Setup pages 14 – 17 Cloning Information pages 28 – 36 FTG Mode of Operation pages 37 – 48 EXPERIENCED INST ALLER Commercial Mode Setup Guide Note: Selected features shown in this guide may not be available on all models. Lodging Guest Interactive Pro:Centric™ TVs © Cop[...]

2 206-4213 MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________ Serial No._______________ W ARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE P ARTS INSIDE[...]

3 206-4213 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accor- dance with the manufacturer ’s instructions. 8. Do not install near any heat sources, such as radia[...]

4 206-4213 (Continued from previous page) 22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, follow the precautions below . An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power [...]

5 206-4213 T able of Contents S a f e t y W a r n i n g s .................................. 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3 – 4 T a b l e o f C o n t e n t s ................................. 5 Commercial Mode Overview . . . . . . . . . . . . . . . . . . . . . . 6 – 8 S e t u p C h e c k l i s t ..[...]

6 206-4213 Commercial Mode Overview This document describes how to set up L T670H Pro:Centric™ TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’ s CPU, Pr oto co l T rans lat or Ca rd (P TC) , or embedded b -LAN™ (EBL) module, or it res[...]

7 206-4213 Commercial Mode Overview (Cont.) T ypical Installer Menu TV Setup Menus Installer Menu T o cre ate a Maste r T V Setu p, you wil l need to know how to acc es s the com me rci al contr ol ler (PTC ) Inst al ler Menu and make chang es to the def aul t val ues as requ ire d. If nec ess ar y , fam ili ari ze yours el f with the Ins ta lle r [...]

8 206-4213 FTG Mode This mode enables Pro:Idiom ® decryption and also allows logical channel mapping of physical channels to remove the need for dash tuning. T V o pe rat ion i n F TG Mo de is ba se d o n whi ch el eme nt of t he T V own s the FT G Log ic al Ch ann el Ma p—t he CP U o r the E BL. U nde rst an din g the ap pl ica ti on in wh ich [...]

9 206-4213 Pro:Centric Operation Pro:Centric TV Interactive Menu Features When running the Pro:Centric application, the interactive Pro:Centric TV enables guests to locate and select television entertainment using an interactive channel guide, check the daily weather , and view hotel and surrounding amenities via custom billboards and poi nts -of -[...]

10 206-4213 Pro:Centric Setup Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric™ Server Admin Client User Guide . This document describes only those settings that must be specied on the TVs. On the TVs, the Data Channel must be set appropriately to enable Pro:Centric remote management/ [...]

1 1 206-4213 Automated Installation Routine Wizard Note: If it has been compl eted or ex ited and th erefo re do es no t displ ay , th e Automated Installation Routine Wizard can be re-a ctiva ted; howev er , this requir es th at fa ctory defa ults be res tored on t he TV(s ). Refer to Re feren ce se ction , “Re stori ng Fac tory Defau lts o n th[...]

12 206-4213 Automated Installation Routine Wizard (Cont.) Pro:Centric Manual Conguration If you a lre ad y k no w t he re qui re d D ata C han ne l a nd Pr o:C en tri c App lic at ion M ode s ett ing s for t he T V , y ou ma y s tre am lin e the set up pr oce ss by e nte rin g thi s dat a m an ual ly . 1. Use the Up/Down arrow keys on the Instal[...]

13 206-4213 Automated Installation Routine Wizard (Cont.) USB Con figur atio n Co nf i gu r in g T V Ple as e wa it. .. 95% W arn ing - Do n ot r emo ve t he US B de vic e du rin g th is p roc ess Plea se sele ct conf igur atio n file (*.tlx ) xxL T670H-UA 00005 .TLX Acces sing USB Stora ge Devi ce OK Move Pre v. USB Conguration This section des[...]

14 206-4213 Custom Master TV Setup Channel Auto Tuning (Channel Lineup) Manual Tuning Channel Edit Channel Label Picture Picture Mode Audio Auto V olume Clear V oice Sound Mode Balance TV Speaker Time Auto Clock Auto Off (Sleep Timer) Option Menu Language Audio Language Caption Lock Movie Rating TV Rating – Children TV Rating – General Note: So[...]

15 206-4213 Custom Master TV Setup (Cont.) 2. Set Installer Menu items. This step p rovid es sp ecic inst ructi on onl y on the I nstal ler M enu i tems that should be s et on a Ma ster TV . Refer to page s 18 to 26 for detail ed infor mation on a ll In stall er Me nu it ems. a) Us e th e I ns t a ll e r R e m o te t o a c c es s th e P TC I ns [...]

16 206-4213 Custom Master TV Setup (Cont.) CHA NN EL OK Mo ve • Auto T uning • Manual T uning • Channel Edit • Channel Label (Optional) Use Channel Menu options to run Auto Tuning, edit channels, and select channel icons. (Continued on next page) 4. (Optional) Run Auto T uning. Note: If you intend to use a USB memory device / .tlx file for [...]

17 206-4213 Custom Master TV Setup (Cont.) 6. (Optional) Add Custom Channel and Aux Input Labels: 2-5-4 + MENU Mode Note: 2-5-4 + MENU Mode enables you to add/ed it channel icons and custo m text labels in the PTC once the Maste r TV Setup has been trans ferred as descri bed in the previo us step. Acc ess the Ins ta lle r Men u, and pres s 2-5 -4 +[...]

18 206-4213 Installer Menu T ypical Installer Menu Use the Installer Menu to set up, change, or view operational settings. Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing. Accessing the Installer Menu 1. Turn ON the TV . If the Automated Installation Ro[...]

19 206-4213 Using the Installer Menu Refer to th e tab le on page s 20 and 2 1 for an ov ervie w of the a vaila ble In stall er Me nu it ems, inclu ding their item numbe rs, f uncti ons, value range s, an d def ault value s. Installer Menu items not relevant to these TV models are not present in the Installer Menu; therefore, some numbers are missi[...]

20 206-4213 Installer Menu (Cont.) Installer Menu Items 000 through 075 Menu Item Function V alue Range Default V alue Brief Description of Function and Comments 000 INST ALLER SEQ 0 ~ 3 0 Leave default set to 0. 001 POWER MANAGE 0 ~ 7 0 Sets number of hours of no activity before automatic shutoff. 002 AC ON 0 / 1 0 Set to 1 to enable Auto T urn ON[...]

21 206-4213 Installer Menu Items 078 through 122 Menu Item Function V alue Range Default V alue Brief Description of Function and Comments 078 UPN MSB 0 ~ 255 0 User programmable number , most significant byte. 079 UPN MSB-1 0 ~ 255 0 User programmable number , most significant byte - 1. 080 UPN MSB-2 0 ~ 255 0 User programmable number , most signi[...]

22 206-4213 Installer Menu (Cont.) Detailed Descriptions of Installer Menu Items 000 - INST ALLER SEQUENCE Species entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy . If set to[...]

23 206-4213 Installer Menu (Cont.) 01 1 - KEY DEFEA T (Keyboard Defeat) If set to 1, KEY DEF EA T preve nts th e end user from a ccessi ng the on-scr een me nu(s) from the di splay panel —MENU SETTIN GS, OK, an d menu navig ation keys do not func tion. If set to 0, thos e keys d o func tion. Note: Users can always access the menus by pressing MEN[...]

24 206-4213 Installer Menu (Cont.) 069 - EN. CH-T COL. (Enable Channel-Time Custom Color) Set to 1 to enable custom color for the Channel-T ime display . Set to 0 to disable custom color for the Channel-T ime display . 070 - FOR. CH-TIME (Ch ann el- T ime Di spl ay Fo reg rou nd Col or) Set according to Color Chart: 0 = Black 3 = Cyan 6 = Y ellow 1[...]

25 206-4213 • 5 = Scaler Model RJPs: HDMI Mode Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI source is connected to the RJP , both digital video and audio are expected via the HDMI cable. If no digital audio is present, no audio will be heard. • 6 = Scaler Model RJPs: DVI Mode Enables RJP feature for u[...]

26 206-4213 1 19 - DA T A CHANNEL Set to 0 (default) to disable. Set to the RF channel number of the data channel for Pro:Centric or TV E-Z Installation (splash screen, configuration, or firmware) data. Note: Pro:Centric updates are downloaded from the Pro:Centric server to the TV when the TV is turned OFF . Also, while Pro:Centric updates are in p[...]

27 206-4213 Channel Icons / Custom T ext Labels (2-5-4 + MENU Mode) Changing a Channel’ s Icon on the Master TV 1. Use Channel Up/Down to select the desired channel. 2. Use the Left/Right arrow keys to select the thin letter “ I ” on the Channel-T ime display . 3. Use t he Up /Do wn ar row k eys to sel ect t he ic on wi th whi ch yo u wan t t[...]

28 206-4213 Cloning Overview IMPORT ANT CLONING INFORMA TION There are four different procedures for cloning a Master TV Setup, each with its own advantages and limitations (see also “Cloning Methods” on page 14): • Using a USB memory device / .tlx le • Using a USB memory device / .tll le • Using a TLL-1 100A clone programmer • Us[...]

29 206-4213 USB Cloning Procedures Learning / T eaching a Master TV Setup using a USB Memory Device / .tlx File USB Cloning Notes • Re ad the I MPO R T ANT CL ON ING I NFO RM A TI ON on pa ge 28 be fo re be gin ni ng any c lon in g p ro ced ure s. In par ti cul ar , ens ur e t hat t he Ma ste r T V S et up doe s not c ont ai n a Ch an nel M ap; o[...]

30 206-4213 USB Cloning Procedures (Cont.) T each Master TV Setup to T arget TV 1. Turn ON the T arget TV . The next step depends on whether the Automated Installation Routine Wizard appears on the screen when you turn ON the TV : • If th e w iz ard i s d is pla yed , the TV is already in the required factory default state. Use the Up/Down arrow [...]

31 206-4213 USB Cloning Procedures (Cont.) Learning / T eaching a Master TV Setup using a USB Memory Device / .tll File USB Cloning Notes • Read the IMPORT ANT CLONING INFORMA TION on page 28 before beginning any cloning procedures. • Y ou may edit a lename as part of the Learning procedure; however , a le with edited contents will not be[...]

32 206-4213 T each Master TV Setup to T arget TV 1. Turn ON the T arget TV . The next step depends on whether the Automated Installation Routine Wizard appears on the screen when you turn ON the TV : • If th e w iz ard i s d is pla yed , the TV is already in the required factory default state. Use the Up/Down arrow keys on the Installer Remote to[...]

33 206-4213 Clone Programmer Cloning Procedures Learn Setup from Master TV 1. Ensure the Master TV is set up completely and in Pass-through Mode. 2. Tune/set the TV to an analog channel or Aux input, and then, plug one end of the MPI cable into the TV MPI port. 3. Turn ON the TLL-1 100A. 4. Use the MODE button on the TLL-1 100A to select Clone Mode[...]

34 206-4213 (Optional) Set the Clock Set the time on a Master TV’ s clock. (If the time has alrea dy been copied from a TV into the TLL-1 100A clone programm er , you can set the Master TV’ s clock by copying the time from the clone progra mmer .) The T LL-1 100A can copy the current time to both a Master TV and to the clone’ s intern al cloc[...]

35 206-4213 Learn Setup from Master TV 1. Ensure the Master TV is set up completely and in Pass-through Mode. 2. Tune/set the TV to an analog channel or Aux input, and then plug one end of the MPI cable into the TV MPI port. 3. If there is a good connection after the L T2002 is connected to the TV MPI port, “THE CLONE HAS CONTROL OF THE TV” mes[...]

36 206-4213 Clone Programmer Cloning Procedures (Cont.) (Optional) Set the Clock Set the time on a Master TV’ s clock. (If the time has alrea dy been copied from a TV into the L T2002 clone programm er , you can set the Master TV’ s clock by copyin g the time from the clone program mer .) The L T2002 can copy the current time to both a Master T[...]

37 206-4213 FTG Mode of Operation Overview FTG Mode via CPU This mode provides the following features: • Logical channels mapped to either RF or IP delivered content. • Digital RF channel minor (program) numbers up to 999. • FTG Channel Map of up to 600 logical channels. • St a rt C ha n ne l se t f or RF , A ux i np u t, o r I P de li ve r[...]

38 206-4213 FTG Mode of Operation Overview (Cont.) PICT UR E A UD IO INP UT OPT IO N TIM E MY ME DI A CHA NN EL L OC K TV Setup Menus Shows that the TV is in Pass-through Mode . Function Menu Indicates the TV is not in Pass-through Mode . While the TV is in this mode, Installer Menu settings can be accessed as read-only . ABC ASP ECT RA TIO OK Mov [...]

39 206-4213 FTG Mode via CPU Creating an FTG Conguration File using the FTG File Manager This section describes how to create an FTG Conguration (.tlx) le that can be saved to a USB memory device. In order to enable Pro:Idiom decryption, it is recommended that you create an FTG Conguration le using the FTG File Manager . Notes: • F[...]

40 206-4213 FTG Mode via CPU (Cont.) (Continued from previous page) Note: T o remo ve an indiv id ual item from the FTG Co nfi gur at ion List or the T V Setu p Men u Lis t, cli ck on/ hig hli gh t the it em to be re mov ed , and the n cli ck th e Remo ve Item but to n dire ct ly ab ove the app lic ab le “Li st” wind ow . T o clea r both the cu[...]

41 206-4213 Note: If the Automat ed In stalla tion Routi ne Wi zard appea rs on the screen when you turn ON th e TV , you c an us e the “USB Con gurat ion” option to c ongu re th is TV , if d esire d (se e “US B Con gura tion” on pa ge 13). 1. Turn ON the TV , and then plug the USB memory device that contains the FTG Conguration[...]

42 206-4213 FTG Mode via CPU (Cont.) 1. Turn ON the TV , and then plug a USB memory device into the USB IN port on the TV . 2. Press MENU SETTINGS on the Installer Remote to display the TV setup menus (TV is in Pass-through Mode) or the Function Menu (TV is already in FTG Mode). 3. Use t he ar row na vi gat io n k eys t o s el ect /h igh lig ht ei [...]

43 206-4213 FTG Mode via CPU (Cont.) T ypical Installer Menu Note: The Installer Menu header will vary depending on the TV you are setting up. Use Channel Menu options to run Auto T uning and edit the channel lineup, as necessary . Adjust the values for these Installer Menu items. 1 17 F ACT DE F AUL T 00 0 003 BAN D/A FC 0 01 Set Installer Menu It[...]

44 206-4213 FTG Mode via EBL Laptop PC ANT EN NA / CAB LE I N TV - LIN K CFG AUD IO IN (RG B/D VI ) PTC SE R VIC E (SE RV IC E O NL Y) VI DEO L /M ON O - A UD IO - R A V IN L R 1. Install (if necessary) and launch the FTG Device Configuration Application (v5.0.0 or higher) on the PC that will be used to configure the EBL. 2. Build an FTG Channel Ma[...]

45 206-4213 FTG File Manager Utilities Overview Note: The data referenced in the FTG Conguration List is only a snap- shot of the current FTG Channel Map and FTG Installer Menu settings when copied to the list. If you make any change(s) to the current data to be included in the FTG Conguration List, you will need to recopy Channel Map and Ins[...]

46 206-4213 FTG File Manager Utilities Overview (Cont.) FTG Channel Map Conguration Utility The FTG Channel Map Configuration Utility enables you to create, view , edit, and print a Logical Channel Map. PRINT MAP Click to display a printable FTG Channel Map Report. The report can also be exported as an HTML or T ext file. EDIT/ADD MAP Cli ck to [...]

47 206-4213 FTG File Manager Utilities Overview (Cont.) DELETE Click to remove highlighted channel from FTG Channel Map. ADD After defining a new Logical Channel, click to add channel to the FTG Channel Map. FTG Channel Map Editor The FTG Channel Map Editor shows a single Logical Channel’s data and the FTG Channel Map. EXIT Click to exit editor a[...]

48 206-4213 FTG File Manager Utilities Overview (Cont.) CONFIGURA TION SETTINGS Select tabs for categories of Installer Menu items to set up TV . FTG Installer Menu Conguration Utility Notes: • The Pro:Centric tab enables you to set up Pro:Centric-specic parameters. Refer to the Free-T o- Guest (FTG) File Manager User Guide for further info[...]

49 206-4213 Remote Jack Pack Setup RJP A vailable? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093 RJP A V AILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP A V AILABLE to 001). See Installer Menu detailed descriptions for further information. TV Connections Make these connections ONL[...]

50 206-4213 Reference: Upgrading TV/PTC Software using a USB Memory Device Upgrading TV/PTC Software Before you begin, note that the software upgrade les must be stored in a folder named “LG_DTV” in the root directory of the USB memory device. Also, ensure the USB device has been formatted with F A T format. Not e f or TV S oft wa re Upg ra [...]

51 206-4213 Reference: Do wn l oa di n g a S pl a sh Sc re e n us i ng a US B M e mo ry De vi c e Splash Screen Image File Guidelines • The splash screen image must be a baseline (not progressive) JPEG. • The image should be no larger than 1 MB. • The ideal size for the image is 1366 x 768 pixels or under . • The image le must be stored [...]

52 206-4213 Reference: Power Consumption Settings The following tables assume that Installer Menu item 1 18 POWER SA VINGS is set to 003 (default) and Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 100). Item 099 Back Lighting (Static) 26L T670H 32L T670H 37L T670H 42L T670H Power Consumption (W atts) Percent Savings [...]

53 206-4213 Reference: TV Aux Input Conguration DIRECT ACCESS T uning TV ENABLE MPI DA T A ST ART AUX SOURCE ASSIGN- MENT Installer Menu MPI DA T A ST A TUS TYPE 0x41 SOURCES ENABLED (R/W) DA T A ST A TUS TYPE 0xD2 CURRENT A V SOURCE (R) DA T A ST A TUS TYPE 0x 0D AUX SOUR CE (R) OLD_ OCV = 0 OLD_ OCV = 1 Source Input Source Mode Number Labeling[...]

54 206-4213 Reference: b -LAN Setup & Overview A b -LAN enabled head end device, such as an LG FMA-LG101, broadcasts over the RF distribution system to communicate to multiple TVs. When the TV is first installed, it must be turned ON in order for its embedded b -LAN module to receive communication from the head end device. At this point, if it [...]

55 206-4213 Reference: RJP Model List & Input Auto-sensing Hierarchy RJP Input Auto-sensing Hierarchy Priority Video Audio 1st (Highest) Digital Video In Audio In (3.5mm) 2nd PC Video In Audio In (L/R) 3rd Video In Digital Video In RJP Legacy Models • RJP-101M • RJP-101ML • RJP-1 10F • RJP-1 10FW • RJP-1 10W • RJP-1 10WBR • RJP-1 [...]

56 206-4213 Thi s s ec tio n des cr ibe s h ow to r est ore f act or y d ef aul ts ei the r on a s in gle TV th at is c urr ent ly in P ass -t hro ugh or FTG M ode o r o n mul tip le TVs t hat a re cu rre ntl y in FT G M ode . Note: If the TV(s) is/are currently in FTG Mode, restoring the factory defaults also resets the TV to Pass- through Mode. I[...]

57 206-4213 OPT IO N OK Mo ve Reference: TV Zone Restrictions Close 1 ► ► The FT G Cha nn el Ma p E dit or in t he FTG F ile M ana ge r ’ s F TG Ch an nel Ma p Con g ura tio n Uti li ty en abl es you to a ssi gn Zo ne re str ic tio ns to ch an nel s tha t may be d eem ed un sui ta ble f or ce rta in lo cat io ns, f or exa mpl e, a ho tel l[...]

58 206-4213 RGB IN (PC ) AN TE N NA / CA BL E I N TV -LI NK CF G AU DI O IN (R GB /D VI ) SP EA KE R OU T( 8Ω ) PT C SE R VI CE (S ER V IC E ON L Y) / DVI IN 1 2 .......... RE S E T UP D A TE RJP INTERF A CE GA ME C ON TR OL /MPI RS-2 32C (S E R VI C E & E XT P O WE R ) .......... VI D EO L / MO N O - A U D IO - R A V IN L R DC I N Reference: [...]

59 206-4213 Reference: Installer Remote Control T ypical Key Functions CH.PREVIEW CH VOL 1 2 3 4 5 6 7 8 0 9 P A G E Q.MENU BANK CHAR/NUM FLASHBK EXIT OK GUIDE PORT AL TV DVD INPUT MARK CC TIMER MUTE INFO PIP PIPCH+ PIPCH - SWAP PIP INPUT SAP MENU SETTINGS abc def ghi jkl mno pqrs tuv wxyz .,; @ DELETE TV/DVD Select the remote’s operating mode: T[...]

60 206-4213 T roubleshooting General T roubleshooting Some Quick and Easy T ips for Resolving Problems Symptom Possible Cause(s) Possible Solution(s) Installation Cannot direct enter channel number . (TV in Pass-through Mode) Installer Menu item 028 CH. OVERIDE is set to 0, i.e., disabled (recommended setting). If Installer Menu item 028 CH. OVERID[...]

61 206-4213 T roubleshooting (Cont.) T roubleshooting Flow Chart Controller Quick Check ST A TUS LED on PTC Board blinking? Plug into AC Power outlet. TV connected to AC Power? Bad TV Y es No No Y es Cycle the power by removing and reconnecting the AC Power cord. Then, observe POWER LED on front of TV . POWER LED lit? No Y es Press POWER on LG Inst[...]

62 206-4213 T roubleshooting (Cont.) Commercial Mode Check / FTG Operation T roubleshooting TV turned ON? Y es No Press POWER on Installer Remote. TV is not in Commercial Mode. Call T echnical Support for assistance. TV is in Commercial Mode. No On-screen menu display no longer toggles? Y es Press MENU repeatedly as if to access the Installer Menu.[...]

63 206-4213 Caution: If the TV is in LodgeNet PPV Mode (check with the site admin- istrator if you are not cer- tain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will damage the clone programmer . T roubleshooting (Cont.) Clone Programmer T roubleshooting Reset Clone Programmer After Static Shock After replacing exhaust[...]

64 206-4213 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider . The end looks like a hex-shaped nut with a wire through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV . 300 TO 75 OHM ADAPTER A small device that connects a 2-wire 300 ohm antenna to a 75 ohm RF jack. It is usually [...]

65 206-4213 Document Revision History / Open Source Software Notice Open Source Software Notice Document Revision History Date Description June 2012 Revision A: New document Product documentation is available online at: www .LGsolutions.com/products . From the Products page, select TVs, Systems & Solutions , then LCD TVs , then the applicable T[...]

206-4213 Revision A © Copyright 2012 LG Electronics U.S.A., Inc. For Customer Support/Service, please call: 1-888-865-3026 www .LGsolutions.com Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a trademark of LG Electronics U.S.A., Inc. b -LAN is a trademark of LodgeNet Interactive Corporation. All other trademarks or r[...]