LG Electronics L194WS manual

M ake sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for furture reference. S ee the label attached on the product and give the information to your dealer when you ask for service. L194WS L204WS User ’ s Guide[...]

A1 This unit has been engineered and manufactur ed to ensure your personal safety , however impr oper use may result in potential electrical shock or fir e hazards. In order to allow the proper operation of all safeguards incorporated in this display , observe the following basic rules for its installation, use, and servicing. On Safety Use only th[...]

A2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventil[...]

A3 Connecting the Display Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Once you connect the stand base, try not to disconnect it. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Before sett[...]

A4 Connecting the Display 1. Put a cushion or soft cloth on a flat surface. T o remove the Stand: 2. Place the monitor face down on the cushion or soft cloth. 3. Hold the product as it follows and lift up the Stand slightly. 4. Change your hold on the product as it follows and turn the Stand Base in the arrow direction. 5. Pull out the Stand to rem[...]

A5 Connecting the Display T o remove the Stand Base: 2. Hold the body of the Stand as it follows. T ype. A 3. Press inside the two long latches at the same time with your strength as it follows. 5. The body of the Stand and the Stand Base are successfully separated. 4. Keep pressing the two latches and use the other hand to hold the body of the Sta[...]

A6 Connecting the Display T o remove the Stand Base: 2. Hold the body of the Stand as it follows. T ype. B 3. Press inside the four latches individually toward each end. 4. Put the Stand Base on a flat surface and pull up the body of the Stand while holding the Stand Base with the other hand. to remove. 5. The body of the Stand and the Stand Base a[...]

A7 Connecting the Display 20 Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~20˚ Ergonomic It is recommended that in order to maintain an ergonomic a[...]

A8 2 1 Connecting the Display Using the Computer 1. Place the monitor in a convenient, well-ventilated location near your computer. 2. Connect the signal cable. When attached, tighten the thumbscrews to secure the connection. 3. Connect the power cord into a proper power outlet that is easily accessible and close to the display.  Wall-outlet typ[...]

A9 Control Panel Functions MENU Button Use this button to enter or exit the On Screen Display. Control Function OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can[...]

A10 Control Panel Functions This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber. Use this button to turn the display on or off. Power Button Power Indicator Use this button to enter a selection in the On Screen Display. AUTO/SET Button AUTO[...]

A11 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Scr een Display Control system. A short example is given below to familiarize you with the use of the contr ols. The following section is an outline of the available ad[...]

A12 NOTE The order of icons may differ depending on the model (A12~A17). On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Scr een Display control, adjustment, and setting menus. To adjust the brightness, contrast and gamma of the screen PICTURE COLOR POSITION TRACKING SETUP Main menu Sub-menu A Reference PRES[...]

A13 On Screen Display(OSD) Selection and Adjustment NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. Y ou wer e introduced to the pr ocedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU B[...]

A14 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. PICTURE PICTURE PR[...]

CLOCK PHASE SHARPNESS To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. To adjust the clearness of the screen. TRACKING TRACKING MENU : Exit : Dec[...]

A16 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description If this does not improve the screen image, restore the factory default settings. If necessary, perform the white balance function again. This function will be enabled only when the input signal is an analog signal. SETUP To choose the language in which the control na[...]

A17 On Screen Display(OSD) Selection and Adjustment Icons Menu Name Sub-menu Name Main menu Sub menu Description To adjust the USER sub-menu function, Press the SET Button MOVIE TEXT NORMAL USER When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen wi[...]

A18 T roubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power on and the power indicator blue or green? ● Is the power indicator amber? ● Do you[...]

A19 T roubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results [...]

A20 T roubleshooting Have you installed the display driver? ● Have you installed the display driver? ● Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? • Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driv[...]

A21 Specifications L194WS NOTE Information in this document is subject to change without notice. Display Sync Input Video Input Resolution Plug&Play Power Consumption Dimensions &Weight Tilt Range Power Input Environmental Conditions Stand Base Power cord 19 inches (48.2 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 19 inches view[...]

A22 Specifications L204WS NOTE Information in this document is subject to change without notice. Display Sync Input Video Input Resolution Plug&Play Power Consumption Dimensions &Weight Tilt Range Power Input Environmental Conditions Stand Base Power cord 20.1 inches (51.1 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 20.1 inches [...]

A23 Specifications Preset Modes (Resolution) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 *15 16 640 x 350 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1152 x 870 1152 x 900 1280 x 1024 1280 x 1024 1440 x 900 1440 x 900 1440 x 900 31.469 31.468 31.469 37.[...]

A24 Installing the W all mount plate This monitor satisfies the specifications of the W all mount plate or the interchange device. 1. Put a cushion or soft cloth on a flat surface. 2. Place the monitor face down on the cushion or soft cloth. 3. Hold the product as it follows and lift up the Stand slightly. 4. Change your hold on the product as it f[...]

A25  Installing the W all mount plate Wall mount plate(Separate purchase) This is stand-type or will mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased. Kensington Security Slot Connected to a locking cable that can be purchased separa[...]

Digitally yours[...]