Lucent Technologies 7820-0802-003 manual

APX 8000 ™ /MAX ® TNT/DSLMAX ™ Physical Inte rface Con fi guration Guid e Part Numbe r 7820- 0802 -003 For softwar e versi on 8.0 May 2 000[...]

Lucent Tec hnologi es Copyright© 2000 Lu cent T echnologies. All rights reserved. This ma terial is protect ed by the c opyright laws of the U nited States and o ther countr ies. It may n ot be rep roduce d, distribu ted, or alte red in any fashion by any entit y (eith er i ntern al or ex terna l to Luce nt T ec hnolog ies), except in acc ordan ce[...]

85x11 B ook Temp late (Pr eliminary) iii Customer Service Customer Service provides a variety of op tions for obtaining in formation about L ucent products and s ervices, softwar e upgrades, and tech nical assistance. Finding information and softw are on the Int ernet V isit the W eb site at http://www.lucent.com/ins for technical inform ation, pro[...]

iv 85x11 Book Template (Prelimin ary) support s ervices p rovide har dware and s oftware so lutions to keep y our networ k operati ng at peak perfor mance. For mo re information, call (8 00) 27 2-3634. Othe r telep hone numb ers For a menu of Lucent ’ s services, call (8 00) 27 2-3634. Or call (5 10) 769-6 001 for an operator . Calling Luce nt fr[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide v Content s Customer Service .......................... ............ ........... ........... ................. ........... ............ ........... ...... iii About This Guide ................ ......... .............. .......... ......... ......... ......... xvii What is in this guid e[...]

vi APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Contents Configurin g the APX 8000 for shelf-co ntroller redundan cy ................. ........... ........... .......... 2- 3 Assigning the system IP address ......................... ........... ........... ........... ................. .......... 2-4 Assigning an Ethernet IP add[...]

Contents APX 8000/MAX TNT/DSLTNT Physical Interface Configur ation Guide vii Chapter 6 Configuring MultiDSP Cards (MAX TNT , AP X 8 000) .......... ......... .......... ......... .............. ......... ......... 6 -1 Introduction to MultiDSP.............. ...... ...... ........... ...... ........... ...... ........... ..... ............ ..... ...[...]

viii APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Contents Specifying analog encoding f or TAOS unit codecs .................... ........... ................. ........... .. 7-22 Configurin g specialized options.......... ........... ................. ............ ........... ........... ................. .. 7-22 Sample T1 config[...]

Contents APX 8000/MAX TNT/DSLTNT Physical Interface Configur ation Guide ix Routing pr otocols .............. ........... ................. ........... ............ ........... ........... ................. .. 10-2 RADIUS................ ................. ............ ........... ........... ............ ................ ............ ........... ..[...]

x APX 8000/MAX TNT/DSLTNT P hysic al Interface Configuration Guide Contents Chapter 15 Configuring OC3-A TM Cards (MAX TNT/DSL TNT) .................. ......... ......... .......... .............. ......... .. 15-1 Introduction to OC3-ATM ............ ...... ........... ............ ..... ............ ..... ........... ............ ..... ........ 1[...]

Contents APX 8000/MAX TNT/DSLTNT Physical Interface Configur ation Guide xi Sample Frame Relay IDSL con figuration ..................... ........... ........... ................. ...... 17-22 Configurin g the DSLTNT ..................... ........... ............ ........... ................. ........... 17-23 Configurin g the Pipeline .............[...]

xii APX 8000/MAX TNT/DSLTNT P hysic al Interface Configuration Guide Contents Start and Stop record s ................. ........... ................. ........... ........... ................. ...... 18-21 Disconnect cause codes ........ ...... ..... ............ ..... ............ ........... ..... ............ ..... ...... 18-21 SNMP support for S[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide x iii Figures Figure 13-1 Example of un channelized DS3 slot card application ............ ............ ........... .. 13-1 Figure 14-1 DS3-ATM interface to ATM network .............. ........... ........... ............ ............. 14-1 Figure 15-1 OC3-ATM interface to ATM network..[...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide xv Ta b l e s Table 1-1 Basic TAOS unit config uration tasks ..................... ................ ............ ........... .... 1-2 Table 5-1 Modem configu ration tasks ................... ........... ........... ................. ........... .......... 5-2 Table 7-1 T1 line configu [...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide xvii About T his Guide What is in t his guide This guide provides the following instr uct ions fo r an APX 8000 ™ , MAX T NT ® , or DSL T NT ™ multiservice access con centrator: • Basi c conf i gurat ion of your u nit • Config uring shel f contro ller redundan cy (A PX 8000 on[...]

xviii APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Documenta tion conv entions • Network security Documentation conventions Following are all the special characters and typogr aphical conventio ns used in this manual: Conv ent ion Mean in g Monospace text Represents text that appears on your com puter ’ s screen, or that coul[...]

Documentat ion se t APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide xix Documentation set The APX 8000/MAX TNT/D SL TNT docum entation set consists of the following manual s. • Read me first: – Access Networks Safety a nd Co mpliance Guide Contains important safety instructions and cou ntry-specific compliance inform ation that [...]

xx APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Documenta tion set • RADIUS: T AOS RADIUS Guide and Refer ence Describes how to set up a T A OS unit to use the Remote Authenticatio n Dial -In User Service (RADIUS) server and contains a complete r eference to RADIUS attributes. • Administra t ion and troublesho oting: APX 800[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 1- 1 1 Performing Basic Configura tion Introduction to basic co nfiguratio n T abl e 1 - 1 lists the sections describ ing the tasks you must perf orm for the T AOS unit basic configuration. The table includes a b rief description of each task and lists the com[...]

1-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Introduc tion to bas ic config uration T able 1- 1. Basic T AOS unit confi guration tasks Section Des c ri pt i o n of tas k Related commands or parameters “ Connecting t o a new u nit ” on page 1- 3 Connect the T AOS uni[...]

Performing Ba sic Configuration Connecti ng to a new unit APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 1- 3 Connecting to a new unit T o communicate with a new T A OS unit, you mu st assign an IP addres s to the shelf controller . Once this is done, you can perfo rm further configur ation over a LAN usin g[...]

1-4 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Configu ring the shelf-con troller IP addres s on a nonr edundant unit 4 V erify that the connection and the IP addres s are correct by pinging any d evice on the netw ork. admin> ping 10.10.10.1 64 bytes from 10.10.10.1: [...]

Performing Ba sic Configuration Settin g the system date APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 1- 5 Setting the system date If the system date displayed on your screen is incor rect, set the correct da te and time with the Date command . For exampl e, to set the date and t ime to Oct ober 22, 2000, [...]

1-6 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Conf ig uri ng a de fa ult gat eway T o change the log lev el, specify an optio n for the Save-Level parameter: admin> set save-level = [ none | emergency | alert | criti- cal | error | warning | notice | info | debug ] ad[...]

Performing Ba sic Configuration Pinging the TAO S unit from a local host APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 1- 7 domain-name = "" dns-primary-server = 0.0.0.0 dns-secondary-server = 0.0.0.0 netbios-primary-ns = 0.0.0.0 netbios-secondary-ns = 0.0.0.0 must-accept-address-assign = no pool-[...]

1-8 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Recommen ded basic security m easures Changing the Ad min p assword A user who k nows the passwor d to the Admin level can p erform any o peration on the T AOS unit, i ncluding chan ging th e configurat ion. The Ad min pass w[...]

Performing Ba sic Configuration Recommen ded basic security m easures APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 1- 9 Following is an example of assigning a T elnet password: admin> read ip-global IP-GLOBAL read admin> set telnet-password = SDwiw87 admin> write IP-GLOBAL written All users attemp[...]

1-10 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Recommen ded basic security m easures T o prevent the T AOS unit router from being used as an intermediary in this type of denial-of -ser vice attack laun ched from another network, you must dis able the T AO S unit from forw[...]

Performing Ba sic Configuration Recommen ded basic security m easures APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 1-1 1 Following are the paramete rs related to SNMP security: SNMP enabled = no read-community = public read-write-community = write enforce-address-security = no read-access-hosts = [ 0.0.0.[...]

1-12 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Performing Basic Configuration Where to go next In the following example, commands enforce address securi ty and specify a trusted address for read and write access: admin> read snmp SNMP read admin> list enabled = no read-community = public read-wri[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 2-1 2 Configu ring Sh elf-Contr oller Redundanc y (APX 8000 ) Over view of redu ndan cy op eratio ns The APX 8000 can oper ate with a single shelf contro ller or with two red undant shelf controllers. When the APX 8000 runs with two shelf controller s, one contr[...]

2-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Shelf-Contr oller Redundancy (APX 8000) Overvie w of redun dancy op erations The controllers next elect the controller that will be primary. The election process is based on a hierarchical list of co mplex criteria. The firs t criterion in the lis[...]

Configuring Shelf-Controller Redundanc y (APX 8000) Config uring the APX 8000 fo r shelf-c ontroll er redundan cy APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 2- 3 Controller switchover If the primary controller fatals, the seco ndar y contro ller autom a tically takes over as primary controller . The new [...]

2-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Shelf-Contr oller Redundancy (APX 8000) Configu ring the AP X 8000 for shelf-c ontroller redundancy Assigning the system IP address T o configure an A PX 8000 t hat has redu ndant s helf control lers, y ou must map system I P settings to th e unit[...]

Configuring Shelf-Controller Redundanc y (APX 8000) Config uring the APX 8000 fo r shelf-c ontroll er redundan cy APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 2- 5 admin> set ip-address = 192.168.100.2/24 admin> write IP-INTERFACE/{ { shelf-1 right-control ler 1 } 0 } written After you assign IP addr[...]

2-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Shelf-Contr oller Redundancy (APX 8000) Configu ring the AP X 8000 for shelf-c ontroller redundancy Configuring shelf-contro ller redundancy When setting up shelf-controller red undancy , you might need to configure the followin g profiles: • Ph[...]

Configuring Shelf-Controller Redundanc y (APX 8000) Config uring the APX 8000 fo r shelf-c ontroll er redundan cy APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 2- 7 admin> read redundancy REDUNDANCY read admin> list [in REDUNDANCY] context = [ { } { } ] primary-preference = no-preference The following[...]

2-8 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Shelf-Contr oller Redundancy (APX 8000) Configu ring the AP X 8000 for shelf-c ontroller redundancy Switchin g the primary controller at the command-line interf ace Y ou can manuall y sw itch primary shelf-controller functio n a lity to the second[...]

Configuring Shelf-Controller Redundanc y (APX 8000) Obtaini ng status informa tion about redundant shelf control lers APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 2- 9 the default security level is reactiv ated . In addition, a system reset can cause a W AN lin e to temporarily be shut down due to momentar[...]

2-10 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring Shelf-Contr oller Redundancy (APX 8000) Obtaini ng status informat ion about r edundant shelf controller s disrupted and then reestablis hed, the uptime command rep orts the time elapsed since the secondary contr oller reestablished commun icati[...]

Configuring Shelf-Controller Redundanc y (APX 8000) Obtaini ng status informa tion about redundant shelf control lers APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 2-1 1 The following example di splays the show comman d entered on the s econdary con troller when the right contro ller is primary: admin>[...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 3- 1 3 Configur in g the Therma l Profile for Fa n T ray Operat ions (APX 80 00) Overview of the Thermal p rofile for fan tray operation s On the APX 8000, an on-board d igital temperature chip on the shelf contro ller and a temperature device at th e intake e[...]

3-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring the Thermal Pr ofile for Fan Tray Operations (APX 8000) Overvie w of the Th ermal prof ile for fan t ray operat ions Example of configur ing thermal controls The command s in the follow ing example sh ow how to co nfigure the fan tray to run th[...]

Configuring the Thermal Profile for Fan Tray Operations (APX 8000) Overv iew of the The rmal profi le for fan tr ay operati ons APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 3- 3 admin> write THERMAL written admin> list [in THERMAL] fantray-lownoise-rpm = 2500 operation-mode = auto-regulation low-temp[...]

3-4 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring the Thermal Pr ofile for Fan Tray Operations (APX 8000) Thermal s tatus re porting Thermal status reporting A power -on self test ( POST) is ru n on the f an tray of the APX 800 0 during the BOOT l oader and during the operational load. If the [...]

Configuring the Thermal Profile for Fan Tray Operations (APX 8000) Thermal status re portin g APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 3- 5 Thermalst atus command The thermalstatus comman d displays a number of temperature-r elated values to sh ow the over all thermal s tatus of the unit. For exam ple,[...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 4- 1 4 Configu ring Et hernet Ca rds Introduction to Ethernet slot cards This chapter explains how to install and co nfigure the Ethern et slot cards. For information about confi guring IP routing, see the APX 8 000/MAX TNT DSL TNT W AN, Routing and T unneling[...]

4-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Ethernet Cards Overvie w of Ether net co nfi gurati on Upgrading to the Ethernet-2 and Et hernet-3 slot cards T o upgrade from an existing 10Mbps or 10/100Mb ps Ethern et card to an Ethernet- 2 or Ethernet-3 slot card, proceed as in the followi[...]

Configuring Ethernet Cards Config uring duple x mode on the 100 Mbps Ethe rnet port APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 4- 3 5 08/06/1998 17:11:46 { shelf-2 slot-4 3 } 5 08/06/1998 17:11:46 { shelf-2 slot-4 4 } If the 1 0/100 Mbps Ethernet-2 card is instal led, t he 100Mbps Ethernet port is d ispl[...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 5- 1 5 Confi g u ring Series5 6 II an d III Modem and Hybrid Access Card s T ypically , Series56 II ™ and Se r ies 56 III Di gital M odem sl ot car ds do n ot requ ire a ny configurat ion. Dependin g on your net work, si tuation s might requ ire you to chang[...]

5-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Series56 II and III Modem and Hybrid Access Cards Specify ing modem negotiati on settin gs Specifying mod em negoti ation setti ngs Calls from analo g modems are d ir ected f irst to th e dig ital mod ems, where the conn ection mus t be negotia[...]

Configuring Series56 II and III Modem and Hy brid Access Card s Speci fying modem modulatio n for Seri es56 II and III modem c ards APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 5- 3 2 List the parameters in the Modem-Conf ig uration subprofile. For example: admin> list modem-configuration v42/mnp = will[...]

5-4 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Series56 II and III Modem and Hybrid Access Cards Series56 II and III Call-Rou te profil es rate and the A T -Answer-S tring par ameter specifies a dif ferent baud rate, the answer string overwrites the configured maxim um b aud rate. Following[...]

Configuring Series56 II and III Modem and Hy brid Access Card s Prevent ing Seri es56 II an d III ca rds from d elayi ng Frame R elay c onnections APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 5- 5 Preventing Series56 II and III cards from delaying Frame R elay connections If the APX 8000 o r MAX TNT has a [...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 6-1 6 Configuring Mult iDSP Cards (MAX TNT , APX 8000) Introduction to MultiDSP The MultiDSP card is a highly versatile, digital signal processor (DSP ) slot card for MAX TNT and APX 8000 units. The following services are s upported by the MultiDSP card: • Dat[...]

6-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring MultiDSP Cards (MAX TNT, APX 8000) Introduc tion to Mul tiDSP 48-port MultiDSP card The 48-port MultiDSP card supports up to 48 ports of servi ce. Note: In MAX TNT and APX 8000 profiles and parameters, the 48-port MultiDSP card is identified as ma[...]

Configuring MultiDSP Cards (MAX TNT, APX 8000) Suppo rted Mult iDSP ser vices APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 6- 3 Card configuration constraints The following constr aints affect th e mixing of slo t cards in MAX TNT and APX 8000 units . Using 48-port and 96 -port Multi DSP car ds Y ou cannot[...]

6-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring MultiDSP Cards (MAX TNT, APX 8000) Suppo rted Mult iDSP s ervic es V .110 features supported by the MultiDSP card include the following: • Asynchronous, answer-mode only (answer , but no call out), with 1 start bit, 8 data bits, and 1 st op bit [...]

Configuring MultiDSP Cards (MAX TNT, APX 8000) Obtainin g status information about a MultiDSP card APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 6- 5 A V oI P so ft ware li cense is required for MultiDS P support of the V oIP service. An additional software license is required fo r supp ort of real-time fax[...]

6-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring MultiDSP Cards (MAX TNT, APX 8000) Configu ring a M ultiD SP card For example, enter the following comman d to di sp lay inf orm atio n about a 96-port MultiDSP card (identified as madd2-car d ) installed in shelf 1, slot 10 of a MAX TNT unit: adm[...]

Configuring MultiDSP Cards (MAX TNT, APX 8000) Configur ing a Mul tiDSP c ard APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 6- 7 • V erifying that all other con figurations associated with the Mu ltiDSP services have been performed. For example, for V oI P MultiDSP support, all required configu rations fo[...]

6-8 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring MultiDSP Cards (MAX TNT, APX 8000) Configu ring a M ultiD SP card ... phs-support = yes ... voip-enabled = no ... v110-enabled = disabled ... rtfax-enabled = no ... V erifying call routes for Mul ti DSP service s Y ou can verify call routes for en[...]

Configuring MultiDSP Cards (MAX TNT, APX 8000) Configur ing a Mul tiDSP c ard APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 6- 9 The following example shows a Call -Route profile for the V oIP service ( entry is 3) on a 48-port MultiDSP card in stalled in slot 5: 33 12/10/1999 18:25:32 {{{shelf-1 slot-5 0} [...]

6-10 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring MultiDSP Cards (MAX TNT, APX 8000) Configu ring a M ultiD SP card Viewing call -routing d ataba s e entri es Unlike the Call Route profiles, entries in a call-routing database are created f or the analog modem service, dig ital service, and for [...]

Configuring MultiDSP Cards (MAX TNT, APX 8000) Configur ing a Mul tiDSP c ard APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 6-1 1 admin> slot -r 1 5 admin> slot -u When the MultiDSP cards are brought u p, the unit cr eates n ew profiles and call route entries for each service, including the new serv[...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 7- 1 7 Configur in g T1 Cards Introduction to T1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7- 2 Overview of T1 co nfiguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

7-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Introductio n to T1 Introduction to T1 A T1 line consists of 24 channels. Each channel can transmit and receive data or digitized voice. The l ine uses fram ing and signal ing to ach ieve synchron ous and rel iable trans mission. The m[...]

Configuring T1 Ca rds Overvi ew of T1 conf iguratio n APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 7- 3 Overview of T1 conf iguration T able 7-1 lists t he secti on s des cri bi ng com mon t ask s you mi g ht hav e to perform t o co nfi g ure a T1 line. The table includes a brief description of each task a[...]

7-4 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Over view of T1 conf igur ati on “ Confi guring i nband robbed-bi t signaling ” on pag e 7-1 1 If the lines use inband signaling, chan ge the sign aling mode t o robbed bit and specify the type of robbed bit signalin g to use. Y ou[...]

Configuring T1 Ca rds Overvi ew of T1 conf iguratio n APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 7- 5 “ Confi guring na iled channels ” on page 7-21 Y ou must assig n a nailed ch annel to a group to m ake it available for use. The group nu mber can be refer red to in a Connectio n or Frame- Relay pro[...]

7-6 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Making a profile the working pr ofile Making a profile th e working profile When the T AOS unit detects that a T1 card has been installed, it creates a default T1 p rofile for each of the eigh t lines on the card. In the followin g dis[...]

Configuring T1 Ca rds Assi gning nam es to T1 li ne profil es APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 7- 7 nfas-group-id = 0 nfas-id = 0 incoming-call-handling = internal-processing call-by-call = 0 data-sense = normal idle-mode = flag-idle FDL = none front-end-type = dsx DSX-line-length = 1-133 CSU-b[...]

7-8 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Enablin g a line Enablin g a line By default each T1 line is disabled. T o enable the T1 line, read its profile to m ake it the working profile, then set the Line Interface subpr ofile ’ s Enabled parameter to Y es, as in the followi[...]

Configuring T1 Ca rds Configur ing ISDN network-s ide emula tion APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 7- 9 admin> set line switch-type = switchtype admin> set line channel 24 channel-usage=d-channel admin> write T1/{ shelf-1 slot-2 1} written T o see a complete list of switch types support[...]

7-10 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Conf ig ur in g over lap r eceiv ing on PRI line s trailing-digits = 2 t302-timer = 10000 [in E1/{ shelf-1 slot-12 1 }:line-inte rface] signaling-mode = isdn overlap-receiving = yes pri-prefix-number = 3069 trailing-digits = 2 t302-tim[...]

Configuring T1 Ca rds Config uring in band robbed- bit sig naling APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-1 1 The following exa mple enables overlap receiving on an E1 PRI line: admin> read e1 {1 16 7} E1/{ shelf-1 slot-16 7 } read admin> set signaling-mode = isdn admin> set overlap-receiv[...]

7-12 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Configu ring inban d robbed- bit signal ing accounting. (On lines configu red fo r PRI sign aling, this inform ation is pr esented as part of the call setup message an d does not require special configur ation on the T AOS unit.) T o c[...]

Configuring T1 Ca rds Conf ig uri ng NF AS APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-1 3 Configuring NF AS A group of T1 lines configur ed for NF AS signaling shares a D channe l. One line in the group is configured with a primary D channel, and anoth er line is configur ed with a secondary D channel[...]

7-14 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Conf ig uri ng NF AS admin> read t1 {1 2 1} T1/{ shelf-1 slot-2 1 } read admin> set line signaling-mode = isdn-nfas admin> set line nfas-id = 0 admin> set line nfas-group-id = 1 admin> set channel 24 channel = nfas-prima[...]

Configuring T1 Ca rds Configur ing T1 R1 and R1-Modi fied (Taiw an) with A NI and cal led-number processin g APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-1 5 admin> write T1/{ shelf-1 slot-2 6 } written admin> read t1 {1 2 7} T1/{ shelf-1 slot-2 7 } read admin> set line signaling-mode = isdn-nf[...]

7-16 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Configur ing T1 R1 and R1-Modi fied (Taiwa n) with ANI a nd called- number proc essing the switch, you can also specify how long it waits before send ing the request, and ho w long the ANIR sig nal l asts . The following par ameters en[...]

Configuring T1 Ca rds Config uring clo cking APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-1 7 Configuring clocking Y ou can configure the T AOS unit to use any of th e T1 lines as a ma ster phase-locked loo p (PLL) clock source f or synchro nous connections for an en tire sys tem. In synchr onous transm[...]

7-18 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Configu ring ch annel us age T o specify CSU settings, proceed as in the following examp le after reading in the line ’ s T 1 profile: admin> set front-end-type = csu admin> set csu-build-out = 7.5-db admin> write Configurin[...]

Configuring T1 Ca rds Assi gning tel ephone num bers to swi tched ch annels APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-1 9 Assigning telephone numbers to switched channels Channel assignment s typicall y specify add -on nu mbers, not fu ll telep hone nu mbers. Ad d-on numbers include only the rightmo [...]

7-20 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Configu ring trunk gr oups admin> set 13 phone = 72 admin> write Configuring trunk groups Like nail ed channels t hat have b een assigned a group number , switched channels in a t runk group can be referred to from a Connection p[...]

Configuring T1 Ca rds Configur ing nail ed channe ls APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-2 1 phone-number = "" call-route-info = { any-shelf any-slot 0 } nailed-group = 0 admin> set trunk-group = 4 admin> write Note: Command h istory is very useful for repeat ing comm ands. Pres[...]

7-22 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Specify ing anal og encoding f or TAOS unit code cs • Clock-Source set to Eligible (the default) In T1 profile for the other end of the line, specify the following values: • Signaling -Mode set to Inband (the defau lt) • Robbed-B[...]

Configuring T1 Ca rds Sample T1 conf igurat ion APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 7-2 3 Sample T1 config uration This section provides an example of h ow to configure a T1 slot card. The example uses the following setu p: • The card is in shelf 1, slot 2. • All lines use PRI sig naling. •[...]

7-24 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T1 Cards Default Call-Route p rofiles 4 Enable the line: admin> set enabled = yes 5 Set the frame type: admin> set frame-type = est 6 Set the line encoding: admin> set encoding = b8zs 7 Set the signaling m ode: admin> set signaling-[...]

APX 8000 Physical Interface Configuration Guide Preli minary M ay 9, 2000 8-1 8 Configur in g T1 FrameLine Card s (MAX TNT , DSL TNT) Introduction to T1 FrameLine The T1 FrameLine slot card provides 10 unchannelized T1 lines, each of which can be used f or one nailed connection. Associated with each T1 lin e is a Serial Communications Adapter (SCA)[...]

8-2 Preliminary May 9 , 2000 APX 8000 Physical Interface Configuration Guide Configuring T1 FrameLine Cards (MAX TNT, DSLTNT) Over view of T1 Fra meLi n e co nfi gur ati on • Multilink Protocol (MP) and Multil ink Protocol Plus (MP+) are no t su ppo rted. The connection profile must speci fy only P PP . • Users are authenticated b y the local p[...]

Configuring T1 FrameLine Cards (MAX TNT, DSLTNT) Configur ing the c lock sourc e APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 8- 3 – Call- by-Call – Channel-Usage – Defa ult-C all- T y pe – Data Sense – FDL – Idle-Mod e – Maintenance-St ate – NF AS-ID – Robbed-B it-Mode – SendDisc-V al [...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelim inary May 9 , 2000 9- 1 9 Configu ring E1 Cards Introduction to E1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9- 2 Overview of E1 co nfiguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

9-2 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Introduc tion to E1 Introduction to E1 An E1 line suppor ts 32 64Kbps channels , each of which can be used to transm it and receive data or d igitiz ed voice. The line uses framing an d signaling to achieve synchron ous and reliable tr[...]

Configuring E1 Cards Overvi ew of E1 configu ration APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 9- 3 “ Confi guring a back-t o-back connection ” on page 9-7 A back-to-back connection lets yo u connect two T AOS units to one an other over a crossover E1 cable. Back-to-Back “ Specifying the framing ?[...]

9-4 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Understa ndi ng co nfig urati on re qui remen ts Understanding co nfi guration requirements Y ou need the follo win g information from your E1/P RI ser vice provider: • The telephone n umbers assigned to your E1/PRI interface, channe[...]

Configuring E1 Cards Making a profil e the work ing prof ile APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 9- 5 • Rate adapt ion pr otocol — DASS 2 and DPNSS only (X.30 and V .110) Note: The T AOS unit cannot receive multichannel calls using Multilin k P rotocol (MP) encapsulation unless all channels of[...]

9-6 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Assign ing names to E1 li ne profiles line-interface = { no none g703 eligible middle-priority + back-to-back = false [in E1/{ shelf-1 slot-15 5 }:line-interface] enabled = yes t-online-type = none frame-type = g703 clock-source = elig[...]

Configuring E1 Cards Enabling a line APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 9- 7 admin> read e1 {1 12 0} admin> set name = E1 Trunk admin> write E1/{ shelf-1 slot-12 0 } written admin> dir e1 17 04/17/1997 19:00:02 { shelf-1 slot-12 0 } "E1 Trunk" For E1 lines , the Line S tatus[...]

9-8 Preliminary May 9 , 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Specify ing E1 s ignalin g admin> set line frame-type = [ G703 | 2DS | D4 | esf ] admin> write E1/{ shelf-1 slot-2 1 } written Specifying E1 signalin g An E1 lin e ’ s si gna l ing mo de can be an y o f the f ollow i ng: • IS[...]

Configuring E1 Cards Configur ing ISDN network-s ide emula tion APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 9- 9 Configure ISDN PRI service as in the following example: admin> read e1 {1 15 5} E1/{ shelf-1 slot-15 5 } read admin> list [in E1/{ shelf-1 slot-15 5 }] name = "" physical-addres[...]

9-10 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Configu ring E1 R1 signalin g ISDN emulation enables you to build, s end, receive, and p rocess ISDN data. ISDN mon itoring, on the other h and, all ows you on ly to decode the ISDN data. Configuring E1 R1 si gnali ng R1 is a mu ltifre[...]

Configuring E1 Cards Configu ring E1 R2 s ignalin g APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 9-1 1 T o configure the line f or R2 signaling, p roceed as in the following example: admin> read e1 {1 2 2} E1/{ shelf-1 slot-2 2 } read Number- Com plete Number of digits considered to be a comp lete numb[...]

9-12 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Conf ig urin g DP NSS si gnal ing admin> list line enabled=no frame-type=g703 clock-source=eligible clock-priority=middle-priority signaling-mode=isdn switch-type=net5-pri front-end-type=short-haul channel-config=[ { unused-channel [...]

Configuring E1 Cards Configur ing ove rlap rece iving on PRI li nes APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 9-1 3 admin> set loop-avoidance = 7 admin> write Configuring overlap receiving on PRI lin es Overlap receiving af fects the procedure of establishing an incoming call received on a T1 or [...]

9-14 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Configu ring ch annel us age Configuring channel usage Y ou must specify how each o f the 32 channels of an E1 line is to be us ed. By defau lt, E1 channels are config ured as switched. Each of the 32 channels of an E1 line can be conf[...]

Configuring E1 Cards Configur ing nail ed channe ls APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 9-1 5 idle-logout = 0 parallel-dialing = 2 single-file-incoming = yes analog-encoding = a-law sessionid-base = 0 admin> set use-trunk-groups = yes admin> write Then assign the channels of each E1 line to[...]

9-16 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 Cards Specify ing anal og encoding f or TAOS unit code cs When you conf igure Connection profiles to use the leas ed connection, y ou must specify the Nailed-G roup num ber in the T elco-Opti ons subp rofile. T o configure a nailed c hannel,[...]

Configuring E1 Cards Default Cal l-Route p rofiles APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 9-1 7 This defaul t Call- Route pro file rout es outbo und trun k calls t o any line o n the card. T o handle inbound m odem and LAN-sessio n traf fic, you must con figure speci fic call ro utes. For d etails, [...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 10-1 10 Configur in g E1 Frame Line Cards (MAX TNT , DSL TNT) Introduction to E1 FrameLine The E1 FrameLine sl ot card provides 1 0 E1 FrameLine lines, each of which can be used for one nailed connection. Associated with each E1 lin e is a Serial Communications Adapter (SCA), which is [...]

10-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 FrameLine Cards (MAX TNT, DSLTNT) Overvie w of E1 FrameL ine confi gurat ion PPP The E1 FrameLine sl ot card supports PPP as follows : • Only one PPP s essi on per li ne. • Bandwidth per ses sion is 1-3 1 DS0 ch annels. Chann el 1 is no [...]

Configuring E1 FrameLine Cards (MAX TNT, DSLTNT) Over vie w of E 1 Fra meL ine con fig ur ation APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 10-3 • Channel-Usage for chan nel must be set to Unus ed-Channel. • For all other channels, Channel-Us age must be set to either Unused-Chann el or Nailed-6 4-Channel. • Chan nel 17 is[...]

10-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 FrameLine Cards (MAX TNT, DSLTNT) Adminis trative profile s for E1 F rameLin e hunt-grp-phone-number-2 = "" hunt-grp-phone-number-3 = "" T o configure the E1 FrameLine card: admin> read E1 {1 2 2} UE1/{ shelf-1 slot-2 [...]

Configuring E1 FrameLine Cards (MAX TNT, DSLTNT) Adminis tr ati v e comm and s and sta tus infor ma tio n APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 10-5 Admin-S t ate profile When you install the E1 FrameLine slot card, the MAX TNT or DSL TNT creates 20 Admin-St ate profiles; 10 are associated with the E1 lines and 10 are asso[...]

10-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring E1 FrameLine Cards (MAX TNT, DSLTNT) Conf ig uri ng th e c lock sou r ce Conf iguring the cloc k sour ce The E1 FrameLine s lot card uses the same system-wide PLL s ynchronous clo ck source fo r DS1 transmission as do the eight-port T1 and E1 c[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary M ay 9, 2000 11- 1 11 Configur in g T3 Cards Introduction to T3 The T3 slot card is a communications circuit composed of seven DS2s, each o f which includes four DS1 s, each of w hich in t urn is compo sed of 24 DS0s, for a total of 672 DS0 chan nels. On the T3 card, DS2 c[...]

11-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T3 Cards Understa nding T3 c onfiguration requir ements For complete infor mation about the as sociated parameters, see the APX 8 000/MAX TNT/DSLTNT Reference . Understanding T3 configu ratio n requ irements Config urin g the T3 slot card is v [...]

Configuring T3 Ca rds Unders tanding T3 slot c ard profil es APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 11- 3 Understanding T3 slot card profiles When the T AO S unit first detects the pr esence of a T3 slot card, it creates the following profiles for each card: • One T3 profile • One Call-R oute pr[...]

11-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring T3 Cards Assign ing a name to a T3 p rofile 13 02/28/1997 10:54:49 { { { she lf-1 slot-8 0 } 0 } 0 } 13 02/28/1997 10:54:49 { { { she lf-1 slot-11 0 } 0 } 0 } 13 02/28/1997 10:54:49 { { { she lf-1 slot-16 0 } 0 } 0 } 13 02/28/1997 10:54:49 { { [...]

Configuring T3 Ca rds Enabling a line APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 11- 5 admin> read t3 {1 12 0} admin> set name = T3 Trunk admin> write T3/{ shelf-1 slot-12 0 } written admin> dir T3 17 04/17/1997 19:00:02 { shelf-1 slot-12 0 } "T3 Trunk" For T3 lines, the Line S tat[...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary May 9, 2000 12- 1 12 Confi gurin g Serial W AN (SW AN) Cards (MAX TNT, DSL TNT) Introduction to SW AN The Serial W AN (SW AN) card, has four V .35 serial ports, which can be used for nailed Frame Relay connections. This card can support u p to 120 Frame Relay virtual circu[...]

12-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring Serial WAN (SWAN) Cards (MAX TNT, DSLTNT) Understa nding SW AN card configurati on requi rements For complete infor mation about the associated param eters, see the APX 8000 /MAX TNT/DSLTNT Reference . Understanding SW AN card configuration requ[...]

Configuring Serial WAN (SWAN) Cards (MAX TNT, DSLTNT) Making a profil e the work ing prof ile APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 12- 3 Making a profile th e working profile When the T AO S unit detects that a SW AN card has been installed, it cre ates a default SW A N profile for each of the li[...]

12-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring Serial WAN (SWAN) Cards (MAX TNT, DSLTNT) Assign ing a name to a SWA N profil e clocking clock-mode = external-clock divider = 1 exp = 2 Assigning a name t o a SW AN profile In a SW AN profile, the Name p arameter enables you to assi gn the prof[...]

Configuring Serial WAN (SWAN) Cards (MAX TNT, DSLTNT) Spec ifyi ng th e SWAN i n ter nal cl ock speed APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 12- 5 Specifying the SW A N inter nal clock speed The SW AN slot card can generate a tran smit or receive internal clock based o n the clock speed of its Seri[...]

12-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring Serial WAN (SWAN) Cards (MAX TNT, DSLTNT) Frame Rela y co nfi gur atio n divider = 1 exp = 2 5 Specify the Divider and exponent to u se for calculating the clock s peed: admin> set divider=4 admin> set exp=2 6 W r ite th e profile: admin&g[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 13 Confi gur ing Unchannelized DS3 Cards (MAX TNT , DSL TNT) Introduction to unch annelized DS3 The unchannelized DS3 slot card (UDS3), supported on the MAX TNT and the DSL TNT, is a 44.736Mbps communications circuit that can b e used to conce ntrate incoming traffi c on the unit and d[...]

13-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Unchannelized DS3 Cards (MAX TNT, DSLTNT) Overvie w of uncha nnelized DS3 configu ration Overview of unchannelized DS3 configura tion T able 9-1 lists the sectio ns descri bing com mon tasks you might have t o perform t o conf igure an unchann [...]

Configuring Unchannelized DS3 Cards (MAX TNT, DSLTNT) Conf ig uri ng th e UD S3 p hysi cal lin k APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 13- 3 By default, each un channelized DS3 line is disa bled. When the DS3 interface is dis abled, it transmits the DS3 Idle Sig n al to the far end. T o assign the [...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 14-1 14 Configu r ing DS3 -A T M Cards Introduction DS3-A TM The DS3-A TM cards (DS3-A TM and DS3- A TM2) suppo rt one 44.736 Mbps interface fo r connecting to o ne A TM switch. At a minimum, yo u must enable the line and specify a n ailed group. T AOS units use the nailed group to dir[...]

14-2 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DS3-ATM Cards Over view of DS 3-AT M set tin gs [in DS3-ATM/{ any-shelf any-slot 0 }:l ine-config] trunk-group = 9 nailed-group = 1 activation = static call-route-info = { any-shelf any-slot 0 } loopback = no-loopback high-tx-output = no framer-mode = C-BIT-PLCP vpi-vci[...]

Configuring DS3-ATM Cards Examp les of DS3 -ATM config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide 14-3 Examples of DS3-A TM c onfigurations The following set of commands enables a DS3-A TM interface in slot 12 and assigns the nailed group nu mber 1 1 1. admin> read ds3-atm {1 12 1} DS3-ATM/{ shelf-1 12 1 } read admi[...]

14-4 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DS3-ATM Cards Example s of DS3-AT M confi guration s Looping back the line T o diagnose possible line pr oblems, you can loop back the DS3-A TM interface by using the Loopback p arameter in the line profile. While the interface is looped back, normal data tr affic is in[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary May 9, 2000 15- 1 15 Configu r in g OC3-A TM Cards (MAX TNT/DSL TNT) Introduction to OC3-A TM An OC3-A TM card pr ovides one 155 .52Mbps interface f or connecting to an A TM switch. At a minimum, you must enable the line and specify a nailed group. MAX TNT and DSL TNT unit[...]

15-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring OC3-ATM Cards (MAX TNT/DSLTNT) Over view o f O C3-A TM s ett ing s rx-descramble-disabled = no tx-scramble-disabled = no rx-cell-payload-descramble-disabled = no tx-cell-payload-scramble-disabled = no loop-timing = yes vpi-vci-range = 0-15/32-40[...]

Configuring OC3-ATM Cards (MAX TNT/DSLTNT) Using O C3-ATM p orts as a clock source APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 15- 3 Using OC3 -A TM ports as a clock so urce OC3-A TM profiles support Clock -Source and Clock -Priority p arameters f or specify ing whether the port c an be used to s ource [...]

15-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring OC3-ATM Cards (MAX TNT/DSLTNT) Example of an OC3 -ATM con figur ation For example, the f ollowing commands configure an OC3-A TM port as an eligible clock source. If this port becomes unavailab le and is not back ed up, the unit begins using the[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary M ay 9, 2000 16- 1 16 Configu ring ST M-0 Ca rds Introduction to STM-0 The Synch ronous T ransport Mo dule (STM)-0 ca rd is an o ptical 51 .85Mbps com munication circuit designed to be used with an approved signaling gateway . Each of its 28 T1 lines can be configu red as [...]

16-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring STM-0 Cards Usi ng S TM an d T1 pr ofiles Using STM and T1 profiles When the T AO S unit first detects the pr esence of an STM-0 card, it creates a default STM profile for the card as well as 28 T1 p rofiles for each component T1 line. The foll[...]

Configuring STM-0 Cards Sample S TM-0 con figurati ons APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 16- 3 Example of configuring a T1 dat a trunk The following command s configure a T1 line as an SS7 data tru nk, enabling the si gnaling gateway to control the line: admin> read t1 {1 1 7} T1/{ shelf-1 s[...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary May 9, 2000 17- 1 17 Configu r in g DSL Connections (DSL TNT) Introduction to DSL technologies Three types of Digital Subscriber Line (DSL) cards are available for the DSL TNT. These cards support either Asymmetr ic Dig ital Subscriber Line (ADSL), ISDN Digital Subscrib er[...]

17-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Introduc tion to DSL technolo gies The IDSL line card pr ovides the following featu res: • ISDN BRI (2B1Q) signaling • T wo DB37 connectors, each providing 16 IDSL sessions f or a total of 3 2 sessions • 128Kbps u[...]

Configuring DSL Connections (DSLTNT) Introduc tion to DSL te chnologi es APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 17- 3 SDSL overview The SDSL card suppor ts symmetric data tran sfer rates of 768 Kbps for a distance of up to 12,000 f eet (3.7 km) ov er a single pair of copper wires. The SDSL-HS data [...]

17-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring DSL Connections (DSL TNT) DSL confi guration For complete details o f configuring authen tication or Frame Relay and PPP connections on your DSL TNT, see the APX 8000 /MAX TNT/DSL T NT W AN, Routing and T unneling Configurati on Gu ide and the A[...]

Configuring DSL Connections (DSLTNT) Configur ing nail ed connec tions APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 17- 5 • Set the Dial # parameter in the Configure prof ile to the DS L po rt number, which in the case of a single DSLPipe is always 1. T o configure a s witched connection on the DSL TNT[...]

17-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Conf ig uri ng d ata t ra n s fer rate s Configuring data transfer rates Y ou can configure DSL upstream and d ownstream rates in the line p rofiles fo r each card, and in Connection or RADIUS profiles. The data transfe[...]

Configuring DSL Connections (DSLTNT) Config uring da ta transf er rates APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 17- 7 For example, if the transceiver is configu red for 108 800 0bps and th e loop qu ality is so poo r that the transceiver will not connect to the remote side, the transceiver does not [...]

17-8 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Conf ig uri ng d ata t ra n s fer rate s T o configure the max imum transfer ra te for the 24 -port SDSL card: 1 Open the SDSL profile: admin> read sdsl {2 1 7} SDSL/{ shelf-2 slot-1 7 } read 2 Enable the line: admin[...]

Configuring DSL Connections (DSLTNT) Config uring da ta transf er rates APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 20 00 17- 9 For more information about thes e parameters, see the APX 8000/MAX TNT/DSL TNT Refer ence . Config uring pe r -se s sion dat a rate s using mode m rate co ntrol In the following exam[...]

17-10 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Conf ig uri ng d ata t ra n s fer rate s admin> set session ses-rate-type = adsl-cap admin> set session ses-adsl-cap-down-rate = 7168000 admin> write CONNECTION/adslpipe-1 written Following is a comparable R A[...]

Configuring DSL Connections (DSLTNT) Config uring da ta transf er rates APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -11 LOG info, Shelf 1, Controller, Time: 16:47:11-- [1/7/1/1] Incoming Call [MBID 18] LOG info, Shelf 1, Controller, Time: 16:47:11-- [1/7/1/0] Assigned to port [MBID 18] LOG info, Shelf [...]

17-12 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Configu ring DSL Pipe Plug a nd Play LOG info, Shelf 1, Controller, Time: 16:47:34-- [1/7/1/0] Assigned to port [MBID 19] LOG info, Shelf 1, Controller, Time: 16:47:34-- [1/7/1/1] Call Connected [MBID 19] LOG info, She[...]

Configuring DSL Connections (DSLTNT) Configur ing DSLP ipe Plug and Play APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -13 Figur e 1 7-1. DSLPipe unit obtaining its con figuration (Plug and Play) The DSLPipe unit uses the m inimal configuration it ob tains via DHCP to access the specified TF TP server an[...]

17-14 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Configu ring DSL Pipe Plug a nd Play TFTP Host Name=host-1.abc.com Boot File Path=/tftpboot/config For a Pipeline unit to op erate as a DHCP server , DHCP Spoofing and Always Spoof must be set to Y es. T o enable the s[...]

Configuring DSL Connections (DSLTNT) Configur ing DSLP ipe Plug and Play APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -15 Configuring the DSL TNT DSLPipe Plug and Play suppor t requires the fo llowing configu ration on the DSL TNT: • BOOTP Re lay enable d • A nailed DSL connection to the DSLPipe •[...]

17-16 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Configu ring DSL Pipe Plug a nd Play 1 Read in the SDSL prof ile. For example, if the SDSL card is installed in s helf 1, slot 1 1 , and the remote DSLPipe is connected to por t 1: admin> read sdsl {1 3 1} SDSL/{ sh[...]

Configuring DSL Connections (DSLTNT) Configu ring IDSL v oice connec tions APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -17 6 W r ite th e profile: admin> write FRAME-RELAY/fr written Config uring a Co nn ectio n profile This example Conn ection profile uses the Frame Relay pr ofile configured in the[...]

17-18 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Conf ig ur in g IDSL voic e conn ect ions Figur e 17-2. Incomi ng and o utgoing vo ice calls Incoming calls Incoming IDSL voice calls requir e that the C entral Of fice (CO) switch support Dialed Number Identification [...]

Configuring DSL Connections (DSLTNT) Configu ring IDSL v oice connec tions APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -19 1 Read the IDSL pro file the remote user is connected to. For example : admin> read idsl {1 7 29} IDSL/{ shelf-1 slot-7 29 } read 2 List the IDSL prof ile: admin> list name =[...]

17-20 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Conf ig ur in g IDSL voic e conn ect ions remote-address = 0.0.0.0/0 local-address = 0.0.0.0/0 .. .. 5 Specify the Pipeline IP addr ess: admin> set remote-address=192.1.2.1/24 6 List the T e lco -Options profile: ad[...]

Configuring DSL Connections (DSLTNT) Configu ring IDSL v oice connec tions APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -21 techpubs-lab-25> list line-interface channel-config [in T1/{ shelf-1 slot-1 1 }:line-inter face:channel-config] channel-config[1] = { switched-channel 9 "" { any-shelf[...]

17-22 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations – My Name= buffer – My Addr= 192.1.2.1/24 – Rem Name= bufferstnt – Rem Addr= 192.1.1.1/24 – Route= IP 3 Exit and s ave the Co nfigure p rofile. 4 Open Ethernet > Conn ections &g[...]

Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -23 Configuri ng the DSL TNT This example assumes the DSL TNT has already been configured with the followin g information: • IP address of 192 .1.1 4/24 • System name of idsltnt T o configur[...]

17-24 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations admin> write Confi gu rin g the ID SL pr ofi le T o configure the DSL TNT IDSL profile, proceed as in the following example: 1 Read the IDSL pro file that the remote user is co nnected to[...]

Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -25 admin> write Configu ring a static route t o the gateway T o configure a static route to the gateway: 1 Read in the IP-Route Default profile: admin> read ip-route default 2 Enter the a[...]

17-26 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations – Name= idsl-fr – Active= Yes – Call T ype = Nailed – Nailed Grp= 1 3 Exit the Frame R elay profile and s ave your chan ges. Note that the Pipeline uses th e follo win g nailed group[...]

Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -27 Confi gur ing t he ADSL prof ile T o configur e the ADSL profile in this example: 1 Read in the ADSL pro file: admin> read adsl-cap {1 7 3} 2 Enable the port: admin> set enabled=yes 3 [...]

17-28 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations 6 V erify that IP routing is enabl ed (the default) for this Connection profile: admin> set ip-routing-enabled = yes 7 V erify that VJ header predictio n is not en abled for this Connecti[...]

Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -29 2 Specify the following valu es: – Chan Usage= Leased/Unused – My Name= dslpipe – My Addr= 10.10.73.1/24 – Rem Name= max-tnt – Rem Addr= 104.178.115.163/24 – Route= IP – Bridge[...]

17-30 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations Figur e 17-5. E xample S DSL setup with in terface -based r out ing Configuring an SDSL conn ection requires the following gene ral step s: • Configuring the Connectio n profile • Config[...]

Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -31 admin> set local-address=192.168.23.142/30 7 List the subm enu for Frame Relay optio ns: admin> list .. fr-options [in CONNECTION/sdsl-pipeline:fr-option s] frame-relay-profile = "[...]

17-32 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations Confi gur ing t he SDSL prof ile T o configure the SDSL profile : 1 Read in the SDSL prof ile. For example, if the SDSL card is installed in s lot 1 1 of shelf 1 and the remote DSLPipe-S is [...]

Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -33 Conf igur ing t he D SLPip e-S This section provides an example of co nfiguring the SDSL Pipelin e (DSLPipe-S). For complete informa tion about configuring the DSLPipe-S, s ee the documentat[...]

17-34 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations 2 Specify the following valu es: – Name= Frame Relay – Active= Yes – Call Type= Nailed 3 If your Pipeline supports it, set Lin kUp to Y es: – LinkUp= Yes Note that this parameter doe[...]

Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -35 3 Specify the encapsulation ty pe as Frame Relay: admin> set encapsulation-protocol=frame-relay 4 List the IP -Optio ns submen u: admin> list ip-options [in CONNECTION/sdsl-pipeline:ip[...]

17-36 Preliminary May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring DSL Connections (DSL TNT) Sample DS L config urations Confi gur ing t he SDSL prof ile T o configure the SDSL profile : 1 Read in the SDSL prof ile. For example, if the SDSL card is installed in s lot 1 1 of shelf 1 and the remote DSLPipe-S is [...]

Configuring DSL Connections (DSLTNT) Sample DS L config urations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 17 -37 Before you configure the Pip e lin e, make sure of the following: • The PC connected to the Pipeline has an I P address on the s ame subnet as the Pipeline. • The IP address of the Pipel[...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary M ay 9, 2000 18- 1 18 Signali ng System 7 (SS7) Introduction to SS7 Signalin g S yst em 7 ( SS7) i s an i ntern ationall y st and ardi zed gener a l-pur pos e co mmon -chan nel signaling system designed for use ov er a variety o f digital circuit -switched net works . At t[...]

18-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Signaling System 7 (SS7 ) System requireme nts for SS7 operatio ns System requirements for SS7 oper ations A T AOS unit config ured for SS7 in communication with an SS7 signaling gateway is a service switching point (SSP) . T o operate in th is cap acity ,[...]

Signaling System 7 ( SS7) System requirem ents for SS 7 operations APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 18- 3 T AOS unit as te rminator of voice and dat a calls in an SS 7 network W ith the IPDC license, the T AO S unit can communicate with th e signaling g ateway by means of IPDC. IPDC enables th[...]

18-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway See MultiV oice for MAX TNT Configuration Guide for a m ore detailed des cription of how V oIP calls are processed by IPDC. Interface between a signal ing gateway and T AOS unit TCP/IP is th[...]

Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 18- 5 Settings in the SS7-Gateway profile con figure the signaling interf ace. The T A OS unit resets the signaling link whenever changes ar e written to the profile. Following are the para met er[...]

18-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway Specifying the SS7 control protocol W ith the appropria te sof tware lic ense, T AOS supports eit her ASGCP an d IPDC 0.1 2 control protoco l. If onl y one of t he poss ible con trol p rotoc[...]

Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 18- 7 System IP address consider ati ons The System-IP-Addr par ameter of the IP-G lobal profile specifies the sou rce address of all packets gener ated by the system, s uch as the connection requ[...]

18-8 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway For so me sites, ad ministrativ e policy or other constraints introduce a requirement to use t he system addres s for some pur poses, bu t to use a separ ate source addr ess for commun icati[...]

Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 18- 9 [in T1/{ shelf-1 slot-1 7 }:line-inter face:channel-config:24] channel-usage = switched-channel Exam ple of c onfig uring a T3 ca rd fo r SS7 da ta T o configure lines of a T3 car d as SS7 d[...]

18-10 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway admin> set line-interface enabled = yes admin> set line-interface signaling-mode = ss7-data-trunk admin> set line-interface incoming-call-handling = inter- nal-processing admin>[...]

Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-11 For example, the following com mands con figur e an E1 line as an SS7 data trunk, ena bling the signaling gateway to control th e line: admin> read e1 {1 10 1} E1/{ shelf-1 slot-10 1 } re[...]

18-12 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway per-line basis. Both the native 2-wire continuity check (GR-246-CORE Section B.2) and 4-wire-t o-2-wire emulation (GR-246-CORE Section B.3) are supporte d. Note: Outgoing contin uity tes ts[...]

Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-13 T AOS also supports the 4-wire- to-2-wire continuity ch eck, with the following req uirements: The exchang e that terminates 4 wires must use a transmitting f requency of 1780 ± 20 Hz and a[...]

18-14 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway For examp le, the fol lowing string def ines a 1004hz t one at 227 48 ampli tude for 1 second: " 1004, 0, 22748, 1000 " The follo wing stri ng defines a d ual tone with fre quency[...]

Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-15 ss7nmi de bug-l evel com mand The T AOS unit reports th e V oIP call statistics in the output of the ss7nmi debug- level command. When the comm and is entered with the -s option, the results[...]

18-16 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway Number of CONNECT to ASG: 0 Number of CONNECT_ACK from ASG: 0 Number of SETUP rejected from: L3: 0 CC: 0 Number of DISCONNECT requests fr om: L2: 0 CC: 0 Number of REGISTRATION to ASG: 0 Nu[...]

Signaling System 7 ( SS7) Configuring an SS7 s ignaling gat eway APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-17 Number of CONNECT to ASG T otal number of active connectio ns to the signaling gateway since it was last reset. Number of CONNECT_ACK from ASG Number of connection acknowledgements the T AOS[...]

18-18 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Configu ring an SS 7 signal ing gateway Command outpu t showing errors The following sample in dicates that errors were detected in SS7 connections: admin> ss7asg -s SS7 Signaling Gateway interface statis tics: Initialized suc[...]

Signaling System 7 ( SS7) Cause co des fo r SS7 ASGC P call s to th e TAOS un it APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-19 Number of T308 expiry events: 0 Last L3 counters reset timestamp: [02/16/1999 10:33:31] Data Transport Layer: Number of link fail-overs: 0 Number of persistent errors: 0 Last[...]

18-20 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Cause co des for S S7 ASGC P call s to the T AOS un it • The T A OS unit reports User bus y (17) i f it cannot find a r oute, or if no reso urce is available for the call. SS7 IPDC support for call ID and disconnect cause codes[...]

Signaling System 7 ( SS7) Cause co des fo r SS7 ASGC P call s to th e TAOS un it APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-21 ft1-caller = 0 calling-number = { "" unknown unknown unspecified unspecified } force-56kbps = 0 redirect-number = "" call-direction = 0 global-call-id = 0[...]

18-22 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Signaling System 7 (SS7 ) Cause co des for S S7 ASGC P call s to the T AOS un it DIS_Q850_TEMPORARY_FAILURE 841 T emporary failure DIS_Q850_NETWORK_CONGESTION 842 Switching equipment conges tion DIS_Q850_ACCESS_INFO_DISCARDED 843 Access information discar[...]

Signaling System 7 ( SS7) SNMP s upport fo r SS7 APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 18-23 SNMP support for SS7 The SS7 MIB ( mgstat.mib) is implemented as a b ranch object with the main o bject, mgGroup , linked i nto t he As cend en ter pris e MIB. F or defi ni ti ons and descr ip ti ons of ob [...]

[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prel iminary M ay 9, 2000 19- 1 19 Confi gur in g Call Routi ng : The T A OS unit uses a set of call -routing algorith ms to ro ute inboun d and ou tbound calls to devices that handle the ap propriate call type. For example, the unit routes an inbound voice-service call to a mod em and[...]

19-2 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Call Routing Understa nding the cal l-routing database Some slot cards act in a dual capaci ty , performing b oth network and hos t funct ions. Some dual-purpose cards provide their own HDLC reso urces. For examp le, T1 and E 1 FrameLine cards [...]

Configuring Call Routing Unde rsta ndi n g th e cal l-r outi ng databa se APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 19- 3 How call routes affect device usage The system sorts its call-routing databa se en tries after a reset. During active use, the system applies operational criteria, such as availabil[...]

19-4 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Call Routing Understa nding the cal l-routing database 3:1:4 ... The system uses the first modem on the lower -number ed card, then the first mo dem on the next card. It then u ses the second mo dem on each of the cards, and so forth. Th is sor[...]

Configuring Call Routing Working with Call-Ro ute profil es APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 19- 5 Hybrid Access card. See “ Dedicat ing Series 56 cards t o modem pro cessing ” on page 19-9 for related information . T runk li ne usage and sort ord er T runk lines are sorted in the order in[...]

19-6 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Call Routing Working wi th Call-Rou te profil es Outbound call routing by trunk group If no exp licit call routes are defined, the T AOS unit always routes a call to the first entry in its database that matches the call ’ s parameters and is [...]

Configuring Call Routing Working with Call-Ro ute profil es APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 19- 7 W ith out an explicit call r oute for trunk group 8 , the system always tr ies the first E1 card, f inds that it d oes not use trun k group 8, and then drops t he call. The following com mands cr[...]

19-8 Preliminary May 9, 2000 APX 8000/MAX TNT/DSLTNT P hysical Interf ace Configuration Guide Configuring Call Routing Working wi th Call-Rou te profil es The next set o f commands creates an other Call-Route prof ile for the Hybr id Access card and sets the preferred source to the secon d E1 interface in s lot 2: admin> new call-route { { { she[...]

Configuring Call Routing Another way to ro ute incom ing calls (deprecat ed) APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Prelimi nary May 9, 2000 19- 9 The following commands create a Call-R oute profile to rou te calls received on trunk group 4 to the Hybrid Access card in slot 4: admin> new call-route { { { 1 4 0 } 0} 0} CA[...]

19-10 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Call Routing Call rout ing algo rithms For example, the f ollowing commands specify that calls received o n the tenth T1 channel on line 1 of a card installed in shelf 1, slot 22 is always routed to the specified host d evice: admin> read t[...]

Configuring Call Routing Call routing algorithms APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 19-11 How the system finds a route After sorting the call-routing d atabase, the T AOS unit compares t he information i t has gathered about a call to the values in the da tabase, looking for a match. V alues are[...]

19-12 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Call Routing Call rout ing algo rithms Det ails of how a r oute is chosen The system comp ares call information to its database entries. The entries are accessed in th e order in which they are sorted, with devices that are us ed less frequent[...]

Configuring Call Routing Call routing algorithms APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminar y May 9, 2000 19-13 equal to the i npu t numb er , and its digits mus t match the add- on digits of the i np ut nu mber . For example, suppose the calling switch sent the fo llowing number to the T AOS unit: 555-1212 Profiles [...]

19-14 Preliminar y May 9, 200 0 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Configuring Call Routing Call rout ing algo rithms voice service, all profiles that speci fy Digital-Call-T ype are removed from cons ideration. Only profiles that specify V oice-Call-T ype or Any-C all-T ype r e mai n in the list. Note: For T1 lines that[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Preliminary May 9, 2000 A- 1 A Provisioning the Switc h This appendix pr ovides th e information neces sary for p roperly p rovisioning a sw itch for T1/EI or T1/E1 PRI access to the W AN. Provisioning the switch for T1 access If you u se an inb and signaling line, the T1 circu it at t[...]

A-2 Prelimi nary May 9, 200 0 APX 8000/MAX TNT/DSLTNT P hysical Interface Configuration Guide What you need from your T1 s ervice p rovider What you need from your T1 service provider Request the f ollowing infor mation about you r T1 interface from your W AN provider: • T ype of signal ing (inban d or ISD N D channel) • T ype of line enco ding[...]

APX 8000/MAX TNT/DSLTNT Physical Interf ace Configuration Guide Index-1 Index A ACM. See address complete mes sage (ACM) activation, for serial W AN card , 12-3 add-on nu mbers desc ribed , 7-19 specifying , 7-19 addresses requiring call to accept dyn amic , 1-9 used to route calls received on chann el , 19-13 used to route calls to a d evice , 19-[...]

Index-2 APX 8000/MAX TNT/DSLTNT Physical Interface Config uration Guide bearer capability and , 9-10 signalin g modes des cribed , 9-8 cause codes access S S7 gateway c ontro l protocol (ASGCP) calls , 18-19 disco nnect, sign aling s ystem 7 (S S7) supp ort f or call ID , 18-20 CCITT . See Co nsultative Com mi ttee for International T elephone and [...]

APX 8000/ MAX TNT/DSLTNT Physical I nterface Configu ration Gu ide Index-3 serial W AN card configurati on requir ements , 12-2 setting date and time , 1-5 setting log level , 1- 5 shelf-contro ller redu ndan c y , 2-1 , 2-6 signaling interface parameter s , 18-5 sign a ling s ystem 7 (SS7) ga teway , 18-4 specifying defau lt gateway , 1-6 specifyi[...]

Index-4 APX 8000/MAX TNT/DSLTNT Physical Interface Config uration Guide DS3-A TM physical interface , 14-2 DS3-A TM port physi cal-a ddress , 14-2 DSL config uring naile d connect ions , 17-5 configuring switched co nnections , 17-4 data transfer rates, configuring , 17-6 enabling on ly active ports , 17-4 IDSL voice connections , 17-17 incoming ID[...]

APX 8000/ MAX TNT/DSLTNT Physical I nterface Configu ration Gu ide Index-5 Ethernet configu ring full duplex m ode on E thernet-2 card , 4-3 installing Ethernet-2 card , 4-2 overview of Ether net card configuration , 4-2 related prof iles , 4-2 shelf cont roller and r outin g load , 1-4 shelf controller interface f or managem ent , 4-2 specifying d[...]

Index-6 APX 8000/MAX TNT/DSLTNT Physical Interface Config uration Guide I IAM. See initial address message (IAM) ICD. See Internet Call Diversion (ICD) ICMP redir ects, conf iguring s ystem to ig nore , 1-9 Idle mode for T1 lines , 7-5 , 7-22 IDS L incoming vo ice calls , 17-18 outg oing vo ice c alls , 17 -18 suppor ted CPE devi ces , 17-4 voice c[...]

APX 8000/ MAX TNT/DSLTNT Physical I nterface Configu ration Gu ide Index-7 modems A T modem st rings , configur ing addi tional , 5-3 conf iguri ng V . 34 m odul atio n , 5-3 specifying nego tiation settings , 5-2 modulati on, conf iguring V .34 fo r 56K mod em , 5-3 MP/MP+ calls FrameLine card and , 8-2 , 10-2 multichannel calls disrup ted by fo r[...]

Index-8 APX 8000/MAX TNT/DSLTNT Physical Interface Config uration Guide T AOS default valu e , 18-6 Use-System-IP -Address-As-S ource , 18- 7 pass word s assigni ng to seri al port , 1-8 changing Admin , 1-8 not saved by defau lt , 1-8 SNMP comm unity strings , 1-1 1 Te l n e t , 1-8 perm i s s ions, A llow- Passwo rd not enab l e d by def ault , 1[...]

APX 8000/ MAX TNT/DSLTNT Physical I nterface Configu ration Gu ide Index-9 shelf -con troll er , 2- 6 shelf-control ler primary election , 2-1 shelf-control ler startup electio n , 2-1 robbed-bit config uration , 7-1 1 routing protoco ls supporte d by E1 F rameLine card , 10-2 protoco ls support ed by FrameLine car d , 8-2 shelf controlle r Ethern [...]

Index-10 APX 8000/MAX TNT/DSLTNT Physical Interface Co nfiguration Guide cause codes for access SS7 gateway control proto co (ASG CP) ca lls , 18-19 connections statistics , 18-15 connectio ns, error r eporting , 18-15 control protocol s pecification , 18-6 E1 lines as data trunks , 18- 10 gatewa y , confi guration , 18-4 incoming calls , 18-4 inte[...]

APX 8000/ MAX TNT/DSLTNT Physical I nterface Configu ration Gu ide Index-11 usage , 7-4 , 7-18 T1 line continuity check, two -wire , 18-11 T1 lines assign ing name t o profi le , 7-7 call control for , 7-1 1 call control for line-sid e , 7-1 1 call control for trunk-sid e , 7-1 1 clock so urce and pri ority , 7-4 , 7-17 clo c king for , 7-17 conf i[...]

Index-12 APX 8000/MAX TNT/DSLTNT Physical Interface Co nfiguration Guide transport ser vice TCP/ IP , 18- 4 trans port-la yer options configuration , 18- 6 Tra p p f o f i l e sett i ng up , 2-1 1 Tra p p r o f i l e configuri ng , 2-11 trunk groups assigning to E1 chan nels , 9- 14 , 9-15 assigning to T1 chan nels , 7- 20 configuri ng , 7-20 expla[...]