Makita 1923B manual

Power Planer PI an in g width 82 mm (3-1/4”) MODEL 1923B ~ ~~~~ __ Planing Rabbeting No load 0 vera I I Net depth depth speed (RPM) length weight INSTRUCTION MANUAL 82 mm (3-1 /4”) SPEC I FI CAT IO N S 293 mm 2.9 kg (11-112”) (6.4 Ibs) 16,000 1 mm 23 mm (1 132”) (1 5/16”) x Manufacturer reserves the right to change specifications without [...]

IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invit[...]

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext[...]

ADDITIONAL SAFETY RULES 1. Rags, cloth, cord, string and the like should never be left around the work 2. Avoid cutting nails. Inspect for and remove all nails from the workpiece be- 3. Handle the blades very carefully. 4. Be sure the blade installation bolts are securely tightened before operation. 5. Hold the tool firmly with both hands. 6. Keep [...]

Removing or installing planer blades CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the blade. To remove the blades on the drum, un- screw the three installation bolts with the socket wrench. The drum cover comes off together with the blades. To install the blades, first clean out all chips or for[...]

3. Set the adjust platehet plate on the gauge base so that the planer blade locating lugs on the set plate rest in the mini planer blade groove, then press in the heel of the adjust plate flush with the back side of the gauge base and tighten the pan head screws. 4. It is important that the blade sits flush with the inside flank of the gauge plate,[...]

For shiplapping, the blade edge should be made to protrude outside slightly (0.3 mm - 0.6 mm: 1/64" - 1/32"). Otherwise, nicks and generally poor ship- lapping results. I 4 I I I II CAUTION : Tighten the blade installation bolts carefully when attaching the blades to the tool. A loose installation bolt can be dangerous. Always check to se[...]

Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release i[...]

Shiplapping To make a stepped cut as shown at the right, use the edge fence. Cutting line I Adjust the edge fence until it comes in con- tact with the side of the workpiece, then secure it by tightening the screw. You may wish to add to the length of the fence by attaching an extra piece of wood. Convenient holes are provided in the fence for this [...]

Chamfering To make a cut as shown at the right, align the "V" groove in the front base with the edge of the workpiece and plane it as shown in the figure (A). Use of nozzle assembly Use of the special nozzle assembly will minimize chip scatter, making for a cleaner work area. The nozzle assembly may be attached after I 1 10[...]

Sharpening planer blades 71 Always keep your blades sharp for the best performance possible. Use the sharpening holder to remove nicks and produce a fine edge. First, loosen the two wing nuts on the holder and insert the blades (A) and (B) so that they contact the sides (C) and (D). Then tighten the wing nuts. Immerse the dressing stone in water fo[...]

MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be r[...]

ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injuty to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Planer blade 0 Planer blade Width : 82 mm (3[...]

Fsb.-20-'87 EN 82 mm (3-1/4") POWER PLANER Model 1923B Note: The switch, noise suppressor and other part configurations may differ from country to country. 14[...]

MODEL 19238 Mar-02 '89 US 10 11 12 'yoM A& DESCRIPTION 12 21 31 41 51 66 71 81 91 1 1 1 '7,'o" DESCRIPTION 34 35 36 37 38 39 40 41 42 43 44 45 1 1 2 1 1 1 1 1 1 1 1 1 Pan Head Screw M4r25 (With Washer1 Bel, Cover Poly V Belt 4-241 V Pulley 4-20L V Pulley 4 31 Pan Head Screw M4x20 Wth Washerl Bracket Rubber Pin 4 Ball Be[...]

c t MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one- year period, return the COMPLETE tool, f[...]