Makita 3612C manual

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Router Equipped with Electric Brake MODEL 3612 MODEL 3612C 003647 DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 SER VICE 23. T ool ser vice mu st be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to[...]

5 9. Before using the tool on an actual w ork- piece, let it run for a while. Watc h for vibration or wobb ling that could indicate improperl y installed bit. 10. Be careful of the bit rotating direction and the feed direction. 11 . Do not leave the tool running. Operate the tool only when hand-held. 12. Alwa ys switch off and wait for the bit to c[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Adjusting the depth of cut Place the tool on a flat surf ace. Loosen the lock le ver and lower the tool body until the bit just touches the flat surf ace. Press the lock le ver do wn to lock the tool[...]

7 Stopper bloc k The stopper bloc k has three adjusting hex bolts which raise or lower 0.8 mm (1/32 ” ) per tur n. Y ou can easily obtain three diff erent depths of cut using these adjusting hex bolts without readjusting the stopper pole. Adjust the lowest he x bolt to obtain the deepest depth of cut, f ollowing the method of “ Adjusting depth [...]

8 Speed adjusting dial For model 3612C only The tool speed can be changed by turning the speed adjust- ing dial to a given n umber setting from 1 to 5. Higher speed is obtained when the dial is turned in the direc- tion of number 5. And low er speed is obtained when it is turned in the direction of number 1. This allows the ideal speed to be select[...]

9 OPERA TION CA UTION: • Bef ore operation, alwa ys make sure that the tool body automatically rises to the upper limit and the bit does not protrude from the tool base when the lock le ver is loosened. • Bef ore operation, alwa ys make sure that the chip deflector is installed properly . Set the tool base on the workpiece to be cut without the[...]

10 Straight guide (optional accessory) The straight guide is eff ectively used f or straight cuts when chamfe r ing or groo ving. Install the straight guide on the guide holder with the wing bolt (B). Inser t the guide holder into the holes in the tool base and tighten the wing bolt (A). T o adjust the distance between the bit and the straight guid[...]

11 T o install the templet guide, loosen the screws on the tool base, insert the templet guide and then tighten the screws. Secure the templet to the workpiece. Place the tool on the templet and mov e the tool with the templet guide sliding along the side of the templet. NO TE: • The workpiece will be cut a slightly different siz e from the templ[...]

12 Install the trimmer guide on the guide holder with the wing bolt (B). Inser t the guide holder into the holes in the tool base and tighten the wing bolt (A). T o adjust the distance between the bit and the trimmer guide, loosen the wing bolt (B) and turn the fine adjusting screw (1.5 mm or 1/16 ” per turn). When adjusting the guide roller up o[...]

13 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. Replacing carbon brushes Remov e and check the carbon brushes regularly . Replace when they we ar down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes[...]

14 AC C E S S O R I E S CA UTION: • These accessories or attachments are recommended for use with your Makita tool specified in this man ual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment f or its stated pur pose. If you need an y assistance for more details regarding [...]

Memo 15[...]

Memo 16[...]

17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

18 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

19 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]