Makita 6092DW manual

Cordless Driver Drill Dimensions (L x W x H) Capacities No load speed IRPM) Steel Wood Wood screw High tow Equipped with Electric Brake 10 mm (3/8") MODEL 60921) 10 mm (318") MODEL 6092DW With Fast Charger Net weight INSTRUCTION MANUAL 96V SPECIFICATIONS ~~ ~ ~ A C only 50 Hz ~ 60 Hz DC 72V,96V 1 Hr 10" - 4oo I 247mm x 581" 262m[...]

IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONM[...]

13. DISCONNECT TOOLS. When not in use, before servicing, and when chang- ing accessories, such as blades, bits, cutters. 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on swi[...]

IMPORTANT Length of Cord (Feet) AWG Size of Cord SAFETY 25 50 100 150 18 18 18 16 IN STRU CTI 0 N S 1. 2. 3. 4. 5. 6. 7. 8. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, a[...]

ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the batte[...]

Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, pull out I 0 the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. 1 To insert the battery cartridge, align the tongue on the battery cartridge [...]

0 When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. 0 If you wish to charge two battery cartridges[...]

CAUTION : Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the revers- ing switch to the right for clockwise rota- tion or t[...]

Drilling operation 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer at the point to be drilled. Place t[...]

Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the trigger just as the screw bottoms out. The electric brake will then stop the tool immediately, pre- venting the screw and/or bit from being damaged. When driving wood Scr[...]

Hole When storing the tool, the hole in the heel of the tool is a convenient way to hang it by a cord, hook or other means. Nominal diameter (mm) Wood screw Use the chart to determine the best size Selecting correct Phillips bit driver bit for the size of screw that you wish to use. Bit No. 2.1 - 2.7 (3132'' - 118") --- 3.1 - 4.8 (1/[...]

MA1 NTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 12[...]

ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Slotted Bits Phil1 ips 1 #2 1 784214-0A I Size[...]

0 Battery holster Holster holds extra battery. Part No. 823033-3C 0 Plastic carrying case Part No. 824431-7 0 Tool holster has some bits storage space. Use holster to carry drill only after removing bit. Also, keep the reversing switch lever in neutral position when carrying in the holster. Part No. 823033-36 Part No. 823033-3E (Genuine leather) 0 [...]

Aug -08 86 EN 10 mm (3/8”) CORDLESS DRIVER DRILL Model 6092D Note: The switch and other part configurations may differ from country to country. 15[...]

MODEL 60920 $tD DESCRIPTION Aug -08-'86 EN $tD DESCRIFTION MACHINE ~ 1 2 3 4 5 6 7 8 9 10 11 12 13 15 14 __ 1 1 1 1 1 1 1 1 1 1 1 8 1 1 1 - Drill Chuck SlO Pan Head Screw M5x18 Spindle Ball Bearing 600CiLB Stop Ring E-9 Compression Spring 10 Thin Washer 10 Spur Gear 78 Ring 16 Spur Gear 93 Housing Sef [With Item 271 Pan Head Screw Max22 [With [...]

Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. 2. a). or b). I Ni-Cd 1 Take the battery to your nearest Makita Factory Service Center Take the battery to your nearest Makita Authorized Service Center or D[...]