Makita 6096D manual

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Cor dless Driver Drill Equipped with Electric Brake MODEL 6096D 001717[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA003-1 (FOR All BA TTER Y OPERA TED T OOLS ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic sh[...]

3 SA VE THESE INSTR UCTIONS Wo r k A r e a 1. Keep y our work area clean and well lit. Cluttered benches and dark areas invite acci- dents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Pow e r tools create sparks which may ignite the dust or fumes. 3. Keep bystander s, childre[...]

4 small metal objects that can make a con- nection from one terminal to another . Shor ting the battery ter minals together ma y cause sparks, burns, or a fire. 18. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control. 19. Check f or misalig[...]

5 SA VE THESE INSTR UCTIONS W ARNING: MISUSE or failure to fo llow the safety rules stated in this instruction manual ma y cause serious personal injury . SYMBOLS USD301-1 The f ollowings show the symbols used f or tool. V ....................... volts ................... direct current .................... no load speed .../min ................ re[...]

6 b. That extension cor d is properly wired and in good electrical condition; c. That wire size is at least as large as the one specified in the table below . 9. Do not operate charger with damaged cord or plug - replace them immediatel y . 10. Do not operate charger if it has received a sharp blow , been dropped, or otherwise damaged in any wa y; [...]

7 7. Do not incinerate the Battery Car tridge even if it is severel y damaged or is com- pletely w orn out. The batter y cartridge can explode in a fire. 8. Be careful not to drop, shake or strike bat- tery . 9. Do not charge inside a bo x or container of any kind. The battery m ust be placed in a well ventilated area during charging. SA VE THESE I[...]

8 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed bef ore adjusting or checking function on the tool. Installing or removing battery cartridge • Alwa ys switch off the tool bef ore inser tion or remov al of the batter y cartr idge. • T o remove the battery car tridge, pu[...]

9 • If you try to charge a car tridge from a just-operated tool, sometimes the charging light will not come on. If this occurs, let the car tridge cool off f or a while. Then re- inser t it and try to charge it once more. • When you charge a ne w batter y car tridge or a batter y car tridge which has not been used for a long period, it ma y not[...]

10 • If you charge a battery car tridge from a just operated tool or a batter y cartr idge which has been left in a location e xposed to direct sunlight or heat for a long time, the charging light ma y flash in red color . If this occurs, wait f or a while. Charging will begin after the batter y cartr idge cools. The battery car tridge will cool [...]

11 Rever sing switch action CA UTION: • Alwa ys check the direction of rotation bef ore operation. • Use the re versing s witch only after the tool comes to a complete stop . Changing the direction of rotation before the tool stops ma y damage the tool. This tool has a re versing s witch to change the direction of rotation. Mov e the rev ersing[...]

12 NO TE: • The adjusting ring does not lock when the pointer is positioned only halfwa y between the graduations . • Do not operate the tool with the adjusting ring set between the number 16 and the marking. The tool ma y be damaged. ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed b[...]

13 OPERA TION Screwdriving operation Place the point of the driver bit in the scre w head and apply pressure to the tool. Star t the tool slowly and then increase the speed gradually . Release the switch trigger as soon as the clutch cuts in. NO TE: • Make sure that the driver bit is inserted straight in the screw head, or the scre w and/or bit m[...]

14 CA UTION: • Pressing e xcessively on the tool will not speed up the drilling. In fact, this e xcessive pressure will only serve to damage the tip of your bit, decrease the tool perf or mance and shor ten the service life of the tool. • There is a tremendous f orce ex er ted on the tool/bit at the time of hole break through. Hold the tool fir[...]

15 EN0001-1 Recyc ling the Battery The only wa y to dispose of a Makita batter y is to recycle it. The law prohibits an y other method of disposal. T o recycle the batter y: 1. Remov e the batter y from the tool. 2. a) T ake the batter y to y our nearest Makita F actor y Ser- vice Center or b) T ake the batter y to y our nearest Makita Authorized S[...]

Memo 16[...]

17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

18 1. This product was pur chased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

19 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]