Makita 9060DBL manual

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. Angle Sander MODEL 9060DBL 001015 DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to follo w Maintenance instructions may create a risk of electric shock or injury . USE PROPER EXTENSION CORD: Mak e sure your e xtension cord is in good condition. When using an e [...]

5 9. Make sure the abrasive disc or the wheel is not contacting the workpiece bef ore the switch is turned on. 10. W atch out for flying sparks. Hold the tool so that sparks fly awa y from you and other persons or flammable materials. 11 . Do not leave the tool running. Operate the tool only when hand-held. 12. Do not touch the w orkpiece immediate[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Shaft lock CA UTION: • Ne ver actuate the shaft lock when the spindle is mo ving. The tool ma y be damaged. Press the shaft lock to pre vent spindle rotation when install- ing or removing accessori[...]

7 Installing or removing abrasive disc (optional accessory) NO TE: • Use sander accessories specified in this manual. These must be purchased separately . Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and screw the loc k nut onto the spindle. T o tighten the lock n ut, press the shaft lock fir mly so that the spindle canno[...]

8 Installing or removing wheel guar d CA UTION: • When using a depressed center grinding wheel/Multi- disc, fle x wheel or wire wheel brush, the wheel guard must be fitted on the tool so that the closed side of the guard alwa ys points toward the oper ator. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch o[...]

9 Installing or removing fle x wheel (optional accessory) W ARNING: • Alwa ys use specific guard when depressed center grinding wheel/Multi-disc is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injur y . F ollow instructions for depressed center grinding wheel/ Multi-disc but also use plastic pad o ver wheel.[...]

10 AL W A YS hold the tool fir mly with one hand on rear handle and the other on the side handle. T ur n the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surf ace. During the break-in peri od with a ne w wheel, do not work the grinder in th[...]

11 • AL W A YS use guard with wire wheel br ushes, assuring diameter of wheel fits inside guard. Wheel can shatter during use and guard helps to reduce chances of personal injur y . Unplug tool and place it upside down allowing easy access to spindle. Remo ve any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wr[...]

12 AC C E S S O R I E S CA UTION: • These accessories or attachments are recommended for use with your Makita tool specified in this man ual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment f or its stated pur pose. • If you decide to use y our Makita sander with appro[...]

13 C00169 2 3 5 2 3 6 7 5 8 9 10 2 11 12 4 13 1 001188 9060DBL 1 Grip 36 2 Wheel guard 3 Inner flange 89 4 Depressed center grinding wheel/Multi-disc 5 Lock nut 5/ 8-40 6 Plastic pad 7F l e x w h e e l 8 Rubber pad 170 9 Abrasiv e disc 10 Sanding lock nu t 5/8-48 11 Wire wheel brush 12 Urethane washer 14 13 Wire cup brush - Lock nut wrench 28 - Acc[...]

Memo 14[...]

Memo 15[...]

Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita ’ s[...]