Makita 9067DB manual

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. Angle Grinder MODEL 9067L MODEL 9067DB 001011 DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 SER VICE 23. T ool ser vice mu st be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to[...]

5 cracked or dama g ed wheel immediatel y . Run the tool (with guard) at no load f or about a minute, holding tool awa y from others. If wheel is flawed, it will likel y sep- arate during this test. 7. Use only flanges specified for this tool. 8. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock n ut. [...]

6 SYMBOLS USD292-1 The f ollowings show the symbols used f or tool. V ....................... volts A ....................... amperes .............. alternating current .............. alternating or direct current .................... no load speed .................... Class II Construction .../min ................ rev olutions or reciprocation per[...]

7 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Shaft lock CA UTION: • Ne ver actuate the shaft lock when the spindle is mo ving. The tool ma y be damaged. Press the shaft lock to pre vent spindle rotation when install- ing or removing accessori[...]

8 ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is switched off and unplugged befo re carr ying out any work on the tool. Installing side grip (handle) CA UTION: • Alwa ys be sure that the side grip is installed securely bef ore operation. Screw the side grip securely on the position of the tool as shown in the figure. Installing or remov[...]

9 T o tighten the lock nut, press the shaft lock firmly so that the spindle cannot re volve , then use the lock nut wrench and securely tighten clockwise . T o remove the wheel, f ollow the installation procedure in re verse. Installing or removing fle x wheel (optional accessory) W ARNING: • Alwa ys use supplied guard when flex wheel is on tool.[...]

10 OPERA TION W ARNING: • It should ne ver be necessar y to f orce the tool. The weight of the tool applies adequate pressure. F orcing and e xcessive pressure could cause dangerous wheel breakage. • AL W A YS replace wheel if tool is dropped while grinding. • NEVER bang or hit grinding disc or wheel onto work. • A void bouncing and snaggin[...]

11 Unplug tool and place it upside down allowing easy access to spindle. Remo ve any accessories on spindle. Mount ure- thane washer then thread wire cup brush onto spindle and tighten with supplied wrench. When using brush, av oid applying too much pressure which causes ov er bending of wires, leading to premature breakage . NO TE: • When using [...]

12 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. The tool and its air vents ha ve to be k ept clean. Regular ly clean the tool ’ s air vents or whene v er the vents star t to become obstructed. Replacing carbon brushes When the resin insulating tip in[...]

13 from your Makita distributor or f actory ser vice center , be sure to obtain and use all necessar y f asteners and guards as recommended in this manual. Y our failure to do so could result in personal injury to y ou and others. If you need an y assistance for more details regarding these accessories, ask your local Makita service center . 9067L/[...]

Memo 14[...]

Memo 15[...]

Memo 16[...]

17 Fold Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitb y , Ontario L1N 7B7[...]

18 Y our answer s to the following questions are appreciated. Date Purchased Model No. Serial No. Initial Last Name Street Address City Province AGE: Male Female Married Single Month Day Y ear 20 Under 19 20-29 30-39 40-49 Over 50 P aste Paste P aste Paste P aste P aste Paste P aste P aste Paste P aste Paste P aste P aste P aste Paste P aste Paste [...]

19 F actory Ser vice Centres For the authorized service centre nearest you please refer to the local yellow pages directory under “ tools ” or con- tact our customer service department (Tel) 1-800-263-3734 When you need service... • Explain the problem in a letter • Enclose the letter with the tool • Package carefully and send prepaid to [...]

Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita ’ s[...]