Makita 9564CVL manual

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Angle Grinder 115 mm (4-1/2”) MODEL 9564CVL DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to follo w Maintenance instructions may create a risk of electric shock or injury . USE PROPER EXTENSION CORD: Mak e sure your e xtension cord is in good condition. When using an e [...]

5 8. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock n ut. Damage to these par ts could result in wheel breakage. 9. NEVER use tool with wood cutting bl ades or other sawblades. Suc h blades when used on a grinder frequently kic k and cause loss of control leading to per sonal injury . 10. Hold the t[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Shaft lock CA UTION: • Ne ver actuate the shaft lock when the spindle is mo ving. The tool ma y be damaged. Press the shaft lock to pre vent spindle rotation when install- ing or removing accessori[...]

7 Speed adjusting dial The rotating speed can be changed by turning the speed adjusting dial to a given n umber setting from 1 to 5. Higher speed is obtained when the dial is turned in the direc- tion of number 5. And low er speed is obtained when it is turned in the direction of number 1. Ref er to the table below f or the relationship between the[...]

8 Removing head co ver When use as a grinder , remov e the head cover . Loosen the screws and pull off the head co ver while pulling out its cor- ners. Installing side grip (handle) CA UTION: • Alwa ys be sure that the side grip is installed securely bef ore operation. Screw the side grip securely on the position of the tool as shown in the figur[...]

9 T o remove wheel guard, f ollow the installation procedure in re verse. Installing or removing depressed center grinding wheel/Multi-disc (optional accessory) W ARNING: • Alwa ys use supplied guard when depressed center grinding wheel/Multi-disc is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injur y . Mou[...]

10 OPERA TION W ARNING: • It should ne ver be necessar y to f orce the tool. The weight of the tool applies adequate pressure. F orcing and e xcessive pressure could cause dangerous wheel breakage. • AL W A YS replace wheel if tool is dropped while grinding. • NEVER bang or hit grinding disc or wheel onto work. • A void bouncing and snaggin[...]

11 Operation with wire cup brush (optional accessory) CA UTION: • Check oper ation of br ush b y r unning tool with no load, insuring that no one is in front of or in line with br ush. • Do not use brush that is damaged, or which is out of balance. Use of damaged brush could increase potential f or injur y from contact with broken brush wires. [...]

12 Operation with abrasive cut-off wheel (optional accessory) W ARNING: • When using an abrasiv e cut-off wheel, be sure to use only the special wheel guard designed fo r use with cut- off wheels. • NEVER use cut-off wheel f or side gr inding. During cutting operations, ne ver change the angle of the wheel. Placing side pressure on the cut-off [...]

13 If you need an y assistance for more details regarding these accessories, ask your local Makita service center . 9564CVL 1G r i p 3 6 2 Wheel guard 3 Inner flange 45 4 Depressed center grinding wheel/Multi-disc 5 Lock nut 5/8-45 6 Rubber pad 115 (Hook & loop) 7 Abrasiv e disc (Hook & loop) 8 Wire wheel brush 9 Wire cup brush 10 Wheel gua[...]

Memo 14[...]

Memo 15[...]

Memo 16[...]

17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

18 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

19 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]