Makita N9514B manual

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Disc Grinder 100 mm (4”) MODEL N9514B DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 SER VICE 23. T ool ser vice mu st be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to[...]

5 6. Check the wheel carefull y for cracks or damage before operation. Replace cracked or dama g ed wheel immediatel y . Run the tool (with guard) at no load f or about a minute, holding tool awa y from others. If wheel is flawed, it will likel y sep- arate during this test. 7. Use only flanges specified for this tool. 8. Be careful not to damage t[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the slide s witch actuates proper ly and returns to the “ OFF ” position when the rear of the slide s witch is [...]

7 ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is switched off and unplugged befo re carr ying out any work on the tool. Installing side grip (handle) CA UTION: • Alwa ys be sure that the side grip is installed securely bef ore operation. Screw the side grip securely on the position of the tool as shown in the figure. Installing or remov[...]

8 Installing or removing fle x wheel (optional accessory) W ARNING: • Alwa ys use supplied guard when flex wheel is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injur y . F ollow instructions for depressed center grinding wheel/ Multi-disc but also use plastic pad o ver wheel. See order of assembly on access[...]

9 OPERA TION W ARNING: • It should ne ver be necessar y to f orce the tool. The weight of the tool applies adequate pressure. F orcing and e xcessive pressure could cause dangerous wheel breakage. • AL W A YS replace wheel if tool is dropped while grinding. • NEVER bang or hit grinding disc or wheel onto work. • A void bouncing and snagging[...]

10 cup brush onto spindle and tighten with supplied wrench. When using brush, av oid applying too much pressure which causes ov er bending of wires, leading to premature break- age. Operation with wire wheel brush (optional accessory) CA UTION: • Check oper ation of wire wheel br ush b y r unning tool with no load, insuring that no one is in fron[...]

11 AC C E S S O R I E S CA UTION: • These accessories or attachments are recommended for use with your Makita tool specified in this man ual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment f or its stated pur pose. • Y our tool is supplied with a guard fo r use with a[...]

12 N9514B 1G r i p 3 6 2 Grip holder 3 Wheel guard 4 Inner flange 35 5 100 mm (4 ” ) Depressed centerwheel/Multi-disc 6 Lock nut 10-35 7 Plastic pad 8 100 mm (4 ” ) Flex wheel 9 Rubber pad 10 Abrasive disc 11 Sanding lock nut 30 12 Wire wheel brush 13 Wire cup brush 14 Wrench 14 15 Lock n ut Wrench 20 3 4 5 9 10 31 3 12 11 6 3 4 7 8 6 2 1 00117[...]

13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]