Marantz TT-15S1 manual

Model TT -15S1 User Guide T ur ntab le[...]

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to aler[...]

IMPOR T ANT SAFETY INSTR UCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1. Read Instructions – All the safety and operating instructions should be read before t[...]

20. Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following con[...]

1 CONTENTS CONTENTS ............................................................................................................................................1 BEFORE USE .........................................................................................................................................2 ACCESSORIES ..........................[...]

2 This section must be read before any connection is made to the mains supply. 7 Equipment Main P ower Setting Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. TT-15S1 can be powered by 120V AC only. 7 Copyright Recording and playback of any material may require consent. For [...]

3 A CCESSORIES Before using the turntable, please make sure that you have all of the following accessories. 1. T ur ntab le chassis 2. Center shaft 3. T one ar m 4. T ur ntab le 5. Motor 6. Motor pulley (f or 60Hz areas) 7. Glov es (pair) 8. Ground wire[...]

4 A CCESSORIES 9. 2 Drive belts (1 spare belt) 10. Bear ing oil 11. T ur ntable sheet 12. 3 Allen wrenches (large/medium/small) 1 adjustment screwdriv er 13. Record clamp ( “ Cle v er clamp ” produced by Souther n Engineering) 14. Counter weight 15. T one ar m height adjustment sheet 16. Car tridge (MM type) by Clearaudio[...]

5 ASSEMBLING AND ADJUSTING 1. Installing the ground wire Connect the ground wire to the turntable shaft base. 2. Inserting the center shaft Insert the center shaft into the turntable chassis. 3. Installing the turntable Place the turntable onto the center shaft. 4. Attaching the tone arm a) Pass the Phono cable that is connected to the tone arm thr[...]

6 ASSEMBLING AND ADJUSTING b-2) Direction The direction position is correct when the tone arm is parallel with the side of the turntable base. b-3) When you have determined the height and direction of the tone arm attachment position, tighten the tone arm fixing screw using the Allen wrench (large). After fixing the tone arm in place, remove the co[...]

7 ASSEMBLING AND ADJUSTING c) Attach the cartridge that you attached in the previous step to the tone arm. • When using the included cartridge Attach to the front attachment hole position on the tone arm. • When using a different cartridge Attach the cartridge so that it is 32mm from the stylus tip. d ) Connect the 4 tone arm wires to their res[...]

8 ASSEMBLING AND ADJUSTING d) Lower the lifter lever, and rotate the counter weight to balance the tone arm so that it is parallel with the turntable. e) After finding the balance, raise the lifter lever and attach the anti-skating adjustment screw. 7. Stylus pressure adjustment Adjust to the recommended stylus pressure of the cartridge being used.[...]

9 ASSEMBLING AND ADJUSTING 9. Attaching the motor pulle y Attach the motor pulley to the motor. Using the adjustment screwdriver included to fix the pulley ’ s 3 plastic screws. Be careful not to turn the screws with too much force, as they are made from plastic and can break easily. When attaching the pulley, fix with approximately 3mm space bet[...]

10 NAMES AND FUNCTIONS q P ower switc h (OFF , ON) When it is switched ON, the turntable rotates. w Pulley This is changed to suit the rpm speed of the record to be played. 33 1/3 rpm record ....................................[Lower side] 45 rpm record ..........................................[Upper side] e Belt r T urntable t T urntable sheet y [...]

11 CONNECTIONS AND OPERA TION 7 Connections Make sure that the power supply to both this turntable and the amplifier are OFF before you start connecting. 1. Connect the PHONO cables (L: white, R: red) that are connected to the toner arm to the corresponding L and R [PHONO] input terminals on your amplifier. 2. Connect both the ground wire that is c[...]

12 TR OUBLE SHOO TING If you think a malfunction has occurred, first check the points listed below. 7 Are each of the connections correct? 7 Are y ou operating the turntable correctly as described in this instruction manual? If the turntable does not operate correctly, check all of the items in the following table. However, if none of the items in [...]

13 SPECIFICA TIONS AND EXTERNAL DIMENSIONS DIA GRAM 7 T urntable section RPM ................................................33 1/3 rpm, 45 rpm Drive system ..........................................Belt drive system Turntable ............................................High density acrylic Turntable depth ..........................................[...]

14 The section describes the care and maintenance tasks that must be performed to optimize the operation of your Marantz equipment. 7 Cleaning external surfaces of equipment The exterior finish of your unit will last indefinitely with proper care and cleaning, Never use scouring pads, steel wool, scourging powders or harsh chemical agents (e.g., ly[...]

www .marantz.com You can find your nearest Marantz Authorized Dealer on our website. U.S.A. Marantz America, Inc. 1100 Maplewood Drive, Itasca, IL 60143, U.S.A. Printed in USA 11/2005 00M31BW851250 mzh-d is a registered trademark.[...]