Miele DA 3190 EXT manual

Operating and installation instructions Cooker hoods DA 3160 DA 3180 DA 3190 DA 3160 EXT DA 3190 EXT To avoid the risk of accidents or damage to this appliance it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 06 681 580 e n-G B[...]

Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Description of [...]

Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and can normally be recycled. Packaging e.g. cling film, polystyrene and plastic wrappings must be kept out of the reach of babies and young children. Danger of suffocation! Dispose of or recycle al[...]

This appliance complies with all relevant local and national safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important information on the safety, i[...]

~ Before connecting the appliance to the mains supply, make sure that the voltage and frequency details given on the data plate correspond with the on-site electricity supply, otherwise the appliance could be damaged. Consult a qualified electrician if in any doubt. ~ The electrical safety of this appliance can only be guaranteed when continuity is[...]

~ Do not connect the appliance to the mains electricity supply by a multi-socket unit or an extension lead. These do not guarantee the required safety of the appliance (e.g. danger of overheating). ~ For appliances with an external fan motor fitted (...EXT models) the connection of the two units must be made using the connection cable and the plug [...]

In order to ensure safe operation, and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously, an underpressure in the room of 0.04 mbar (4 pa) is the maximum permissible. Ventilation can be maintained by air inlets which cannot be blocked, in wind[...]

Correct use ~ Never use an open flame beneath the cooker hood. To avoid the danger of fire, do not flambé or grill over an open flame. When switched on, the cooker hood could draw flames into the filter. Fat particles drawn into the cooker hood present a fire hazard. ~ When using the cooker hood over a gas hob, ensure that any burners in use are a[...]

~ Follow the cooker or hob manufacturer's instructions on the use of flammable materials over the cooker/hob when installing a wood or laminate lightshield onto the cooker hood. ~ Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves. ~ All ducting, pipework and fittings must be of non-flammable material. These can be[...]

Guide to the appliance 10[...]

a Exhaust socket ø 150 mm b Control panel c Grease filter d Pull-out deflector plate e Hob lighting f Charcoal filter (extra accessory available to order for recirculation mode) g Drop-down lightshield to conceal control panel The front of the deflector plate can be fitted with a lightshield to match your kitchen furniture (max. weight 1300 g.). T[...]

The cooker hood works with . . . air extraction: The air is drawn in, cleaned by the grease filter and then directed outside. If the on-site ventilation system does not have a non-return flap , then the non-return flap supplied with the appliance must be fitted in the exhaust socket in the motor unit. Having a non-return flap fitted in the ducting [...]

The cooker hood is operated by pulling out and pushing in the deflector plate. To switch the fan on ^ Pull out the deflector plate. The fan will begin to operate at setting II. The On/Off indicator lamp and the 2nd – / + power level indicator lamp will light up. If the cooker hood has been connected to a window contact switch via the Miele DSM 40[...]

Automatic switch-off of the Intensive setting You can set the Intensive setting so that it only runs for 10 minutes before reverting automatically to level III. ^ To set this option, both the fan and the hob lighting must be switched off and the deflector plate pushed in. ^ Press the – and + touch controls at the same time for approx. 10 seconds [...]

Before any cleaning or maintenance work is carried out, disconnect the cooker hood from the mains supply. Ensure that: – it is switched off at the wall socket and the plug is withdrawn, or – the fuse is withdrawn from the fused spur connection unit, or – the mains fuse is disconnected ,or – the screw-out fuse is removed (in countries where [...]

Important for DFB aluminium lightshields (optional accessory) Aluminium is affected by the way that light falls on it, by the surrounding environment and by the angle you observe it from. Aluminium surfaces may suffer discolouration or damage if soiling is left on them for too long. Remove any soiling straight away. Observe the General notes on cle[...]

Cleaning the grease filters by hand ^ Clean the filters with a soft nylon brush in a mild solution of hot water and a little washing-up liquid. Do not use "neat" washing up liquid. Do not use: – cleaning agents containing descaling agents, – powder cleaners, cream cleaners or abrasive all-purpose cleaning agents, – oven sprays. Clea[...]

Fitting and replacing the charcoal filter If the cooker hood is connected for recirculation, a charcoal filter (optional accessory) must be inserted in addition to the grease filter. This is designed to absorb cooking smells. It is fitted in the canopy above the grease filter. Replacement charcoal filters can be obtained from your dealer or the Mie[...]

Changing a halogen lamp ^ Pull out the deflector plate, and remove the grease filter as described earlier. ^ Switch off the fan and the lighting. Exercise caution when changing halogen lamps. They get very hot during use, and remain hot for some time after being switched off. Do not touch the surface directly when changing a lamp, as grease particl[...]

DA 3160 DA 3180* DA 3190* – The front section of the wall housing unit must be fitted with a shelf to the depth of the partition wall. – The partition wall in the wall unit must be removable. * Installation is also possible in a 600 m m wide unit. Appliance dimensions 20[...]

Safety distance between hob and cooker hood The minimum safety distances between the top of a cooker or hob and the bottom of the cooker hood are as follows, unless a greater distance is specified by the manufacturer of your cooking appliance: - 450 mm above electric hobs and cookers, - 650 mm above gas hobs and cookers, - 650 mm above an open gril[...]

Installation accessories Installation 22[...]

a 2 hose clips for securing the vent ducting to the exhaust socket. b 1 reducing collar for exhaust ducting C 125 mm (not on EXT models). c 1 non-return flap for fitting into the exhaust socket on the motor unit (only for air extraction mode, not on EXT models). d 2 brackets to support the appliance in the wall unit. e 1 spacer strip to conceal the[...]

Installation 24[...]

Positioning the appliance in the wall housing unit To position the appliance correctly, cut the spacer strip to required depth T, and then attach it to the back of the appliance. T = Depth of carcase K minus depth of appliance G ^ The depth of appliance G depends on the lightshield being used: – a Lightshield to match existing kitchen furniture ?[...]

^ Screw the brackets onto the right and left inside walls of the housing unit as shown. The back edge of the brackets should align with the vertical line drawn up from the front of the spacer strip, and the lower edge aligned with the lower edge of the housing unit side wall. The brackets are designed for 16 and 19 mm thick carcase sides. Orientate[...]

^ When fitting a DA 3180 or a DA 3190 into a 60 cm housing unit, unscrew the brackets on the deflector plate whilst it is pulled out. ^ Lift the appliance up into the housing from below, and engage in the brackets. Note for dismantling the cooker hood: Undoing the screws on the left and right inside the housing releases the brackets, allowing the a[...]

^ Secure the front of the appliance to the floor of the housing unit from below using 4 screws (6 screws for 90 cm wide cooker hood). To avoid damaging the deflector plate when it is pulled out, care should be taken to screw the fixing screws in straight, and to ensure that the screwheads are countersunk. ^ Secure the spacer strip to the back of th[...]

^ Remove the protective strip around the edge of the grease filter. Replace the grease filter. ^ To do this, pull the deflector plate out. ^ Turn the grease filter so that the red plastic guides are at the front and facing upwards. ^ Replace the grease filter in the front of the deflector plate, press it upwards and push it in together with the def[...]

Set up for recirculation mode If site conditions are not suitable for the cooker hood to be used with air extraction, the appliance must be set up for recirculation. For this, we recommend using the conversion kit available from your Miele dealer or the Miele Spare Parts Dept (see "Technical data"). You will also need a charcoal filter (s[...]

Important: To avoid the danger of toxic fumes please observe the Warning and Safety instructions. This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room. The cooker hood should be installed according to local and national building regulations. Seek approval from the[...]

Important: If the exhaust ducting is to run through rooms, ceiling space etc. where there may be great variations in temperature between the different areas, the problem of condensation will need to be addressed. The exhaust ducting will need to be suitably insulated. Condensate trap (optional accessory) In addition to insulating the exhaust ductin[...]

All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous, for which the manufacturer cannot be held liable. Ensure power is not supplied to the appli[...]

The Miele DSM 400 control module can be used to combine the cooker hood with other components. It enables the following: Connection to a window contact switch If adequate ventilation to the room can only be ensured by having a window open when the cooker hood is in use at the same time as a heating appliance which depends on the air from the same r[...]

Connection to a light switch The control module can be used to switch on the cooker hood lighting via a light switch in the house. Installation The control module must be installed above the cooker hood housing. The control module is supplied with its own detailed operating and installation instructions. Operation with DSM 400 control module 35[...]

In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – Your Miele Dealer or – The Miele Customer Contact Centre (see back cover for address). When contacting your Dealer or the Contact Centre, please quote the mo - del and serial number of your appliance. These are shown on the data [...]

Connected load* .............2 8 0W Fan motor* .................1 8 0W Hob lighting .............2x5 0W Voltage ................. A C2 3 0V Frequency ..................5 0H z Fuse rating (UK) ...............1 3A Electrical cable length .........1 . 5m Weight DA 3160 ....................1 2k g DA 3160 EXT ................1 0k g DA 3190 .............[...]

38[...]

39[...]

Alteration rights reserved / 4007 M.-Nr. 06 681 580 / 04[...]