Miele KM2030 en-CA manual

Installation Instructions KM2030 en-CA IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE To prevent accidents and machine damage read these instructions before installation or use. Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulatio[...]

To avoid damage to the appliance, it should not be installed until the upper cabinet and exhaust hood have already been mounted. ~ This appliance is not connected to an exhaust vent. It must be installed and connected to the power supply in compliance with the applicable installation requirements. ~ The room will need to be at least 20 m 3 in volum[...]

Upper clearance For an exhaust hood above the appliance, the safe clearance distance indicated by the hood manufacturer must be maintained. If there are no specifications from the hood manufacturer or if flammable materials (e. g., a hanging cabinet) are installed above the appliance, the clearance distance must be at least 30" (760 mm). The m[...]

When installing a gas stovetop, the cabinetry or walls to ONE side and to the rear of the appliance can be as tall as you wish. However, on the other side there must not be any appliance or furniture that is taller than the installed gas stovetop (see illustrations). You must ensure that the following minimum safety clearances are kept: – 4"[...]

KM 2030 a front b Installation height c Gas connection R 1/2" ISO 7-1 d Junction box with power cable ,L=7 8 3 / 4 " (2000 mm) Appliance and installation dimensions 29[...]

KM 2050 a front b Installation height c Gas connection R 1/2" ISO 7-1 d Junction box with power cable ,L=7 8 3 / 4 " (2000 mm) Appliance and installation dimensions 30[...]

How to make the countertop cut-out ^ Use the template to make a countertop cut-out. Be sure to observe the minimum distance from the rear wall and from the left or right to a side wall . See the section on "SAFETY NOTICES FOR INSTALLATION". ^ Seal any wooden countertop surfaces with a special varnish, silicone rubber, or resin, to help pr[...]

Sealing NEVER use sealing unless it is explicitly called for in the instructions. The sealing strip under the edge of the upper part of the appliance provides a sufficient seal against the countertop. NEVER use sealing between the upper appliance frame and the countertop! It will hinder access to the appliance during servicing, and the frame and co[...]

This appliance must be grounded according to local or national codes. All electrical work should be performed by a qualified electrician in accordance with local codes and with the: - National Electrical Code ANSI / NFPA 70 for the USA or - Canadian Electrical Code Part I for Canada (CSA Standard C 22.1) , WARNING Disconnect the appliance from the [...]

Installation and service must be performed by a qualified installer, service agency or the gas supplier. This appliance must be installed with its own shut off valve and the included gas pressure regulator. Both the valve and the regulator must be easily accessible to the consumer to turn on or shut off the gas supply after the appliance is install[...]

Gas pressure regulator A pressure regulator that is convertible from natural to LP gas (Propane) or vice versa is included with the appliance. The included regulator corresponds with the gas type of the appliance. Verify before installing. The adjusted pressure is: natural gas - 4" w.c. LP gas - 10" w.c. a Appliance b ½" NPT c Regul[...]

The appliance should have been ordered for connection to either natural gas or LP gas (propane). If the appliance is not configured for the proper type of gas connection please contact your Miele Dealer. If the appliance is to be connected to a type of gas other than it was originally configured for, both the regulator and burners must be converted[...]

Rated load at high setting Burner Type of gas KM 2030 KM 2050 BTU/hr kW BTU/hr kW Small burner Natural gas (NG) Liquid gas (LP) 3500 3500 1,00 1,00 3500 3500 1,00 1,00 Regular burner Natural gas (NG) Liquid gas (LP) 6200 5800 1,80 1,70 6200 5800 1,80 1,70 Power burner Natural gas (NG) Liquid gas (LP) - - - - 8900 8900 2,60 2,60 Wok Natural gas (NG)[...]

, Switchover to a different gas type should only be performed by a duly authorized gas company technician. Save the nozzles removed from the appliance for future use. Nozzle table If you switch to a different type of gas, the large and small burner nozzles will need to be changed. Main nozzle Ø Low setting nozzle Ø Natural gas (NG) Small burner R[...]

How to change a nozzle Unplug the appliance from the electrical supply. How to change the main nozzle ^ Remove the burner cover b , the burner ring a (wok) and the burner head c . ^ Use a socket wrench (M7) to unscrew the main nozzle h . ^ Insert the proper nozzles (see Nozzle table) and tighten them down. Small, normal, and power burners Wok burne[...]

How to change the small nozzles (all burners) To change the small nozzles, you will first need to remove the upper part of the appliance. ^ Unscrew the mounting screws on the burner. ^ Pull the control knob up and off. ^ Take off the upper part of the appliance. ^ Remove the ignition switch a . ^ Use a small screwdriver to unscrew the small nozzle [...]

After switching over ^ Use the reverse order to re-assemble the burner parts. ^ Before putting the upper part of the appliance back in place, light each burner with matches to test the seal on all the gas flow parts. ^ After testing, set aside the loose burner parts. ^ Put the upper part of the appliance back in place. ^ Screw down the lower part o[...]

Alteration rights reserved / 4908 For the most updated manual see the Miele web site. M.-Nr. 07 520 080 / 00[...]