Mitsubishi Electronics MC300 manual

COMPUTER PRODUCTS MC300 Workst ation Computer (Manual Part Number MAN-WKSTN-001)[...]

W ARNING! Programmable control devices such as the MC300 Series Workstation must not be used as stand-alone protection in any application. Unless proper safeguards are used, unwanted start-ups could result in equipment damage or personal injury . The operator must be made aware of this hazard and appropriate precautions must be taken. In addition, [...]

i MAN-WKSTN-001 MC Series Computers CONTENTS CHAPTER 1 INTRODUCTION Manual Organization ............................................................................. 1 Introduction ........................................................................................... 2 What you need to get started ..............................................[...]

ii MC Series Computers MAN-WKSTN-001 CONTENTS This p age intentionally left blank.[...]

1 1 INTRODUCTION MAN-WKSTN-001 MC Series Computers The table, below provides an overall description of the topics covered within this manual. Introduction Provides Manual Organization, and lists what you need to get started. Discusses how to get help with questions or problems you might encounter through T echnical Support. Models and Equipment 2 1[...]

2 1 INTRODUCTION MC Series Computers MAN-WKSTN-001 Introduction The Mitsubishi Electric Automation MC300 Series Workstation Industrial Com- puter features an Intel Pentium III CPU on a single board computer , in various sizes to fit your application needs. An active matrix LCD with resistive-type touchscreen is mounted in a rugged steel enclosure, [...]

3 1 INTRODUCTION MAN-WKSTN-001 MC Series Computers What you need to get st arted: T echnical Support Hardware • Industrial Workstation 6 Slot Panel Computer MC300 — 12-inch MC320 — 15-inch Software • Windows XP Pro (st andard) If you are having difficulty with a particular aspect of installation or setup, technical support is available at 1[...]

4 1 INTRODUCTION MC Series Computers MAN-WKSTN-001 This page intentionally left blank.[...]

5 MAN-WKSTN-001 MC Series Computers Models MC300 12-inch XP Pro Industrial Workstation 6 Slot Panel Computer MC320 15-inch XP Pro Industrial Workstation 6 Slot Panel Computer 2 MODELS AND EQUIPMENT[...]

6 MC Series Computers MAN-WKSTN-001 There are replacement parts and other optional equipment available to cus- tomize or upgrade the Workstation to fit your application. The tables, below , provides you with a list of this equipment. Accessories and Optional Sof tware 2 MODELS AND EQUIPMENT A ccesso r i es Pr o duct Part N um be r 3 2 MB D i sk on [...]

7 MAN-WKSTN-001 MC Series Computers Op tio n a l S o ft w a re Pr o duct Part N um be r Win dow s NT 4. 0 Work stat i on M C7 01 Win dow s 2000 S er v er MC70 2 Win dow s 2000 Pro MC70 3 W in dow s XP Pr o M C704 W in dow s XP Ser v e r M C705 M S DO S M C706 LI N U X Ser v er M C707 LI N U X W/ S M C708 Win dow s N T /e ( E mbedd ed) MC710 Win dow[...]

8 MC Series Computers MAN-WKSTN-001 COMPUTER SPECIFICA TIONS CPU T ype: Intel Pentium III (850 Mhz minimum) Power Supply: A TX 250 Watts Memory: 256 MB (Expandable up to 1.5 GB) Bios: Flash ROM Drive: 40 GB Hard Drive Serial Port s: 1 dedicated RS-232 port, 1 RS-232/RS-422/RS-485 port Parallel Port: SPP/EPP/ECP supported (configurable to LPT1) LAN:[...]

9 MAN-WKSTN-001 MC Series Computers Installing the WORKST A TION requires the following three major steps: The W orkstation is a front-panel stud mount unit. Mounting of the unit requires a p anel cutout, and drilling fourteen (14) holes in the mounting surface for the mounting studs. Please see the Mounting section beginning on page 14 for mountin[...]

10 MC Series Computers MAN-WKSTN-001 Mounting The Industrial Workstation is a panel-mount unit. The following diagrams show the outline and cutout dimensions necessary to mount the Workstation using the studs. 12" and 15" Industrial Wo rkst ation Models MC300 and MC320 Outline Dimensions 4 INST ALLA TION[...]

11 MAN-WKSTN-001 MC Series Computers 12" and 15" Industrial W orkst ation Models MC300 and MC320 Cutout Dimensions 4 INST ALLA TION[...]

12 MC Series Computers MAN-WKSTN-001 Located on one side of the Workstations are the following components: CDROM Drive The computer is equipped with a 48x (or faster) type CD ROM Drive. Floppy Disk Drive The computer is also equipped with a 1.44 MB Floppy Disk Drive. Backlight Adjust (not available on the 12" model) There is also a recessed BA[...]

13 MAN-WKSTN-001 MC Series Computers 5 EXTERNAL COMPONENTS Reset Push Button Push the RESET button to restart the system. Power Control Push Button Push the Power Control ON/OFF button to turn on the computer. When the button is held for 4 seconds, it will turn power OFF . Power LED Next to the ON/OFF push button is a green POWER LED indicator . It[...]

14 MC Series Computers MAN-WKSTN-001 5 EXTERNAL COMPONENTS Power Connector Power In connector to be connected to 1 15 or 230 V AC power source. Power V oltage Selector Slide Switch Switches computer power to 1 15 or 230 V AC — must match power source. Fan This is the power supply fan. One USB (Universal Serial Bus) Connectors There is one USB con[...]

15 MAN-WKSTN-001 MC Series Computers 5 EXTERNAL COMPONENTS Parallel Port Connector Parallel Port Connector (LPT1) is used to connect to a printer . Serial Port Connectors The serial ports are 9-pin D-Sub male connectors. COM1 is a dedicated RS- 232 port. COM2 is a RS-232/RS-422/RS-485 select able port. One KEYBOARD Connector A personal system/2 (PS[...]

16 MC Series Computers MAN-WKSTN-001 Once you have the Workstation inst alled and the peripheral devices connected, you are ready to power up the computer . 1. Plug the Power cable into the Power plug and the Power source. Ensure that the Power V oltage Selector Switch is set for the correct power source being supplied. 2. Press the POWER ON push b[...]

17 MAN-WKSTN-001 MC Series Computers Expansion Card Inst allation The Workstation can accommodate up to 3 PCI and 3 ISA (or 2 ISA and 1 PICMG) expansion cards. T o install an exp ansion card: 1. Disconnect the power source from the Workstation. 2. T o open the rear of the enclosure, remove 9 screws from back of captive p anel. Panel is still suppor[...]

18 MC Series Computers MAN-WKSTN-001 7 MAINTENANCE AND UPGRADES 6. Reinstall card ret ainer bracket. Insert bottom of bracket onto the tab on the housing floor — there are notches at the bottom of the bracket that slide over the t ab. Reinstall the screw to secure bracket to the top t ab. 7. Adjust card retainer foot until it is securely against [...]

19 MAN-WKSTN-001 MC Series Computers Maintenance Preserving Dat a V iruses can corrupt files; files can be inadvertently deleted; and hard-disk drives can fail after extended used. T o avoid data loss, regularly back up the dat a files on the hard-disk drive. If you lose the contents of your hard-disk drive, you can reinst all programs, but your da[...]

20 MC Series Computers MAN-WKSTN-001 T ouchscreen/Chemical Compatibility The touchscreen has a polyester surface. The following list is provided to make you aware of the general comp atibility between chemicals that may be present in your work environment and the polyester surface of the touchscreen. Use the chart to determine those chemicals that [...]

21 MAN-WKSTN-001 MC Series Computers Err or / Impr ovement Report Fill in this form and fax or mail to: For Mitsubishi use only: Name Company Phone Number ________________________ _________________________ ___________________ Manual / Product / Br ochure V ersion ____________________________________________________ ___________________ Description o[...]

22 MC Series Computers MAN-WKSTN-001 This page intentionally left blank.[...]