NAPCO EXPRESS XP-600 manual

Using Your XP-600 Securit y System ARMED READY SYSTEM ü FIRE AC ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 NAPCO Oi218a.pub page 1 Thursday, December 18, 1997 18:29[...]

Introduction Congratulations on your purchase of an advanced NAPCO EXPRESS XP-600 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been de[...]

3 1 Bell / Battery Test Test your bell or siren by pressing A followed by 1 .This will cause the bell, or siren to sound for 2 seconds and also initiate a test of the battery . 2 Central Station Communication Test (This test should only be performed on weekends or at a time designated by your alarm company) 1. Notify Central Station of the impendin[...]

ARMED READY SYSTEM ü FIRE AC ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 4 Keypad Controls and Indicators Ready Light will light when all zones are secure and system is ready to be Armed. AC Light will light to indicate that AC Power is present. Fire Alarm Light will flash and the Keypad sounder will beep when system is in a Fire Alarm Condition (Se[...]

Arming Your System When Leaving 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your prot- ective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure these zones before proceeding. If any zones cannot be secured, see Bypassing Zones below. 2 Enter your user code. Th[...]

Protecting Yourself While at Home 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure those zones before proceeding. 2 Enter your user code. The Green Ready light will go out, and the Red Armed light wi[...]

Emergency Buttons The three sets of emergency buttons, if programmed, are always active whether the system is armed or disarmed. Discuss these Buttons with your installer. The emergency signal will only be activated when the two respective buttons are pressed at the same time. Fire Alarm : Simultaneously press E + E to sound a fire alarm, and to al[...]

Disarming Your System when Returning 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. 2 Enter your user code. The Red Armed light will go out, indicating that the system has been disarmed. Note: If you make a mistake entering your code, pr[...]

Preparing a Fire Escape Plan Even with the most advanced fire alarm system, adequate protection requires an escape plan. To prepare your plan, draw floor plans of your building. (space is provided on the next page) Show two exits - a front or back door and a window from each room. (Make sure each window works. You may need a special fire-escape lad[...]

10 Fire Protection Floorplan Draw a plan of your premises below. Oi218a.pub page 10 Thursday, December 18, 1997 18:29[...]

Special Functions A By pressing A followed by the appropriate key, (do not press simultaneously) these special functions and features can be enabled: A0 Easy Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by pressing A followed by 0 . This will allow the easy arming of the system by someone who is not a regular sys[...]

The XP600 is constantly monitoring its own components, as well as all critical services, such as AC Power and the Telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the yellow ü ü SYSTEM light and beeping the keypad buzzer. If you[...]

13 ü ü System Troubles Keypad Beeps or ü ü SYSTEM Flashes Zone light ON System Trouble Condition Action 2 Beeps 2 Fire Trouble A problem has been detected in the Fire Circuit. Call installing company for service. 2 Beeps 3 Wireless Receiver Trouble A problem has been detected with the wireless receiver. Call installing company for service. 2 Be[...]

Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where you can program other user codes. The following explains how you will use this code to program or erase additional user codes. Entering the User Program Mode Press A followed by 8 and then enter the User [...]

Ambush Code - In the event that you are forced by an intruder to dis- arm your system, this special code can be used to disarm the system, and simultaneously send a silent alarm to Central Station. If your sys- tem has the Ambush feature enabled, the code assigned as the User 6 code will function as your Ambush Code Arming / Disarming - Turning the[...]

NAPCO LIMITED WARRANTY THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with [...]