NEC LCD205WNXM manual

MultiSync LCD205WNXM MultiSync LCD225WNXM MultiSync LCD225WNX User ’ s Manual[...]

English English-1 Declaration Declaration of the Manufacturer TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT T O RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPT ACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULL Y INSER TED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOL T AGE COMPON[...]

English-2 For the Customer to use in U.S.A. or Canada Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouiller du Canad[...]

English English-3 Contents Y our new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD monitor with tilt base • Audio Cable • Power Cord •V ideo Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) •V ideo Signal Cable (DVI-D to DVI-D) (LCD225WNX only) • USB Cable (LCD205WNXM/LCD225WNXM only) • Us[...]

English-4 3. Place hands on each side of the monitor to tilt the LCD panel 30-degree angle and lift up to the highest position ( Figure B.1 ). 4. Connect all cables to the appropriate connector on the back of the monitor ( Figure B.1 ). Using the USB cable, connect the B type connector to the USB upstream port on the bottom of the monitor and A typ[...]

English English-5 9. Hold all the cables firmly and place the cable cover onto the stand ( Figure D.1 ). T o remove the cable cover , lift the cover off as shown in Figure D.2 . NOTE: Handle with care when placing the cable cover and avoid pinching your fingers. 10. Connect the power cord to the power outlet ( Figure D.3 ). NOTE: If you have diffic[...]

English-6 Figure R.2 Non-abrasive surface Figure R.3 Figure R.4 Connecting a Flexible Arm This LCD monitor is designed for use with a flexible arm. Please use the attached screws (4pcs) as shown in the picture when installing. T o meet the safety requirements, the monitor must be mounted to an arm which guaranties the necessary stability under cons[...]

English English-7 Controls OSD (On-Screen-Display) control buttons on the front of the monitor function as follows: 1. Basic function at pressing each key 2. OSD structure Showing OSD. Shortcut to Brightness adjust Menu. Button At No OSD showing Shortcut to V olume adjust Menu. Input signal select. At OSD showing (Icon selection stage) Go to Adjust[...]

English-8 VOLUME Control the sound volume of speakers and headphone. To mute the speaker sound, press the 1<->2/RESET key . BRIGHTNESS Adjusts the overall image and background screen brightness. CONTRAST Adjusts the image brightness in relation to the background. AUTO CONTRAST (Analog Input only) Adjusts the image displayed for non-standard v[...]

English English-9 OSD LOCK OUT This control completely locks out access to all OSD control functions without V olume, Brightness and Contrast. When attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the OSD are locked out. T o activate the OSD Lock Out function, press “1<->2/ RESET”, then “+?[...]

English-10 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MUL TISYNC LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servic[...]

English English-11 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Y our eyes should look slightly d[...]

English-12 Specifications - LCD205WNXM Monitor Specifications MultiSync LCD205WNXM Monitor Notes LCD Module Diagonal: 51.1 cm/20.1 inches Active matrix; thin film transistor (TFT) Native Resolution (Pixel Count): 1680 x 1050 liquid crystal display (LCD); 0.258 mm dot pitch; 300 cd/m 2 (T yp) white luminance, 1000:1 (T yp) contrast ratio, typical; r[...]

English English-13 Specifications - LCD225WNXM Monitor Specifications MultiSync LCD225WNXM Monitor Notes LCD Module Diagonal: 55.9 cm/22.0 inches Active matrix; thin film transistor (TFT) Native Resolution (Pixel Count): 1680 x 1050 liquid crystal display (LCD); 0.282 mm dot pitch; 300 cd/m 2 (T yp) white luminance, 1000:1 (T yp) contrast ratio, ty[...]

English-14 Specifications - LCD225WNX Monitor Specifications MultiSync LCD225WNX Monitor Notes LCD Module Diagonal: 55.9 cm/22.0 inches Active matrix; thin film transistor (TFT) Native Resolution (Pixel Count): 1680 x 1050 liquid crystal display (LCD); 0.282 mm dot pitch; 300 cd/m 2 (T yp) white luminance, 1000:1 (T yp) contrast ratio, typical; res[...]

English English-15 Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The small footprint and low weight allow it to be moved or transported easily from one location to another . Color Control System: Allows you to adjust the colors on your screen and custo[...]

English-16 T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Check front power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display car[...]

English English-17 TCO’03 Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus tha[...]

English-18 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. W e are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standard[...]