NETGEAR M4100-50-POE manual

350 East Plumeria Drive San Jose, CA 95134 USA February 2013 202-1 1 166-02 1.0 Pr oSaf e Manag ed S w it ch Co mmand L ine Inte rfa ce (CLI) U ser Man ual 10. 0.1 M7100-24X M4100-24G-POE+ M4100-26G M4100-26-POE M4100-26G-POE M4100-50G M4100-50-POE M4100-50G-POE+ M4100-12GF M4100-12G-POE+ M4100-D12G M4100-D10-POE M4100-D12G-POE+[...]

2 ProSafe M4100 and M7100 Managed Switches Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my .netgear .com . Y ou must register your product before you can use NETGEAR telephone support. NETGEAR recommends registerin[...]

3 Content s Chapter 1 Using the Command-Line Interface Licensing and Command Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Command Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Command Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

4 ProSafe M4100 and M7100 Managed Switches IGMP Snooping Configuration Commands . . . . . . . . . . . . . . . . . . . . . . . 148 IGMP Snooping Querier Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 MLD Snooping Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 MLD Snooping Querier Commands . .[...]

5 ProSafe M4100 and M7100 Managed Switches Chapter 6 IPv6 Commands Tunnel Interface Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 IPv6 Routing Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357 OSPFv3 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

6 ProSafe M4100 and M7100 Managed Switches Software License Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609 IP Address Conflict Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610 Link Local Protocol Filtering Commands . . . . . . . . . . . . . . . . . . . . . . . . . 611 RMON Stats and Histor[...]

7 1 1. U sing t he C omman d-L ine Int erf ace The command-line interface (CLI) is a text-based way to manage and monitor the system. Y ou can access the CLI by using a direct serial connection or by using a remote logical connection with telnet or SSH. This chapter describes the CLI syntax, conventions, and modes. It contains the following section[...]

Using the Command-Line Interface 8 ProSafe M4100 and M7100 Managed Switches Licensing and Command Support As shown in the following table, some command groups, or commands, require a license and some are supported on particular switch models. For those requiring a license, license keys are available from your V AR or NETGEAR authorized e-commerce p[...]

Using the Command-Line Interface 9 ProSafe M4100 and M7100 Managed Switches Command Syntax A command is one or more words that might be followed by one or more parameters. Parameters can be required or optional values. Some commands, such as show network or clear vlan, do not require parameters. Other commands, such as network parms , require that [...]

Using the Command-Line Interface 10 ProSafe M4100 and M7100 Managed Switches The parameters for a command might include mandatory values, optional values, or keyword choices. T able 1 describes the conventions this document uses to distinguish between value types. T able 1. Parameter Conventions <value> [value] {choice1 | choice2} choice1 | c[...]

Using the Command-Line Interface 11 ProSafe M4100 and M7100 Managed Switches Slot/P ort Naming Convention Managed switch software references physical entities such as cards and ports by using a slot/port naming convention. The software also uses this convention to identify certain logical entities, such as Port-Channel interfaces. The slot number h[...]

Using the Command-Line Interface 12 ProSafe M4100 and M7100 Managed Switches Note: In the CLI, loopback and tunnel interfaces do not use the slot/port format. T o specify a loopback interface, you use the loopback ID. T o specify a tunnel interface, you use the tunnel ID. Using a Command’s “No” Form The no keyword is a specific form of an exi[...]

Using the Command-Line Interface 13 ProSafe M4100 and M7100 Managed Switches commands. Y ou can execute the User EXEC mode commands in the Privileged EXEC mode. The command prompt changes in each command mode to help you identify the current mode. T able 5 describes the command modes and the prompts visible in that mode. Note: The command modes ava[...]

Using the Command-Line Interface 14 ProSafe M4100 and M7100 Managed Switches T able 6 explains how to enter or exit each mode. Router OSPF Config Switch (Config-router)# Contains the OSPF configuration commands. Router OSPFv3 Config Switch (Config rtr)# Contains the OSPFv3 configuration commands. Router RIP Config Switch (Config-router)# Contains t[...]

Using the Command-Line Interface 15 ProSafe M4100 and M7100 Managed Switches Policy-Map Config From the Global Config mode, enter policy-map <name> in . T o exit to the Global Config mode, enter exit . T o return to the Privileged EXEC mode, enter Ctrl-Z . Policy-Class-Map Config From the Policy Map mode enter class . T o exit to the Policy M[...]

Using the Command-Line Interface 16 ProSafe M4100 and M7100 Managed Switches Command Completion and Abbreviation Command completion finishes spelling the command when you type enough letters of a command to uniquely identify the command keyword. Once you have entered enough letters, press the SP ACEBAR or T AB key to complete the word. Command abbr[...]

Using the Command-Line Interface 17 ProSafe M4100 and M7100 Managed Switches CLI Line -Editing Conventions T able 8 describes the key combinations you can use to edit commands or increase the speed of command entry . Y ou can access this list from the CLI by entering help from the User or Privileged EXEC modes. T able 8. CLI Editing Conventions Usi[...]

Using the Command-Line Interface 18 ProSafe M4100 and M7100 Managed Switches enable Enter into user privilege mode. help Display help for various special keys. logout Exit this session. Any unsaved changes are lost. ping Send ICMP echo packets to a specified IP address. quit Exit this session. Any unsaved changes are lost. show Display Switch Optio[...]

19 2 2. S w it c hing C omman ds This chapter describes the switching commands available in the managed switch CLI. This chapter contains the following sections: • Port Configuration Commands • Loopback Interface Commands • Spanning T ree Protocol (STP) Commands • VLAN Commands • Double VLAN Commands • V oice VLAN Commands • Provision[...]

Switching Commands 20 ProSafe M4100 and M7100 Managed Switches • Port Security Commands • LLDP (802.1AB) Commands • LLDP-MED Commands • Denial of Service Commands • MAC Database Commands • ISDP Commands • Priority-Based Flow Control Commands The commands in this chapter are in three functional groups: • Show commands display switch [...]

Switching Commands 21 ProSafe M4100 and M7100 Managed Switches P ort Configuration Commands This section describes the commands you use to view and configure port settings. interface This command gives you access to the Interface Config mode, which allows you to enable or modify the operation of an interface (port). Format interface <slot/port&g[...]

Switching Commands 22 ProSafe M4100 and M7100 Managed Switches no auto-negotiate This command disables automatic negotiation on a port. Note: Automatic sensing is disabled when automatic negotiation is disabled. auto-negotiate all This command enables automatic negotiation on all ports. Default Format auto-negotiate all Mode no auto-negotiate all T[...]

Switching Commands 23 ProSafe M4100 and M7100 Managed Switches no mtu This command sets the default MTU size (in bytes) for the interface. Format no mtu Mode shutdown This command disables a port. Note: Y ou can use the shutdown command on physical and port-channel (LAG) interfaces, but not on VLAN routing interfaces. no shutdown This command enabl[...]

Switching Commands 24 ProSafe M4100 and M7100 Managed Switches no shutdown all This command enables all ports. Format no shutdown all Mode speed This command sets the speed and duplex setting for the interface. Format speed [{auto}] [{<100 | 10 | 10G> {<half-duplex | full-duplex>}}] Mode 100h 100f 10h 10f 10Gh 10Gf speed all This comman[...]

Switching Commands 25 ProSafe M4100 and M7100 Managed Switches show port advertise Use this command to display the local administrative link advertisement configuration, local operational link advertisement, and the link partner advertisement for an interface. It also displays priority Resolution for speed and duplex as per 802.3 Annex 28B.3. It di[...]

Interface Type • Mirror - this port is a monitoring port. For more information, see Port Mirroring on page 121. • PC Mbr - this port is a member of a port-channel (LAG). • Probe - this port is a probe port. Admin Mode Physical Mode Physical Status Link Status Link Trap LACP Mode Switching Commands 26 ProSafe M4100 and M7100 Managed Switches s[...]

Switching Commands 27 ProSafe M4100 and M7100 Managed Switches show port description This command displays the port description for every port. Format show port description <slot/port> Mode Interface Description show port status This command displays the Protocol-Based VLAN information for either the entire system, or for the indicated group.[...]

Switching Commands 28 ProSafe M4100 and M7100 Managed Switches interface loopback Use this command to enter the Interface Config mode for a loopback interface. The range of the loopback ID is 0–7. Format interface loopback <loopback-id> Mode no interface loopback This command removes the loopback interface and associated configuration param[...]

Switching Commands 29 ProSafe M4100 and M7100 Managed Switches IPv6 Prefix is The IPv6 address of the interface. MTU size The maximum transmission size for packets on this interface, in bytes. T erm Definition[...]

Switching Commands 30 ProSafe M4100 and M7100 Managed Switches Spanning T ree P rotocol (STP) Commands This section describes the commands you use to configure Spanning T ree Protocol (STP). STP helps prevent network loops, duplicate messages, and network instability . spanning -tree This command sets the spanning-tree operational mode to enabled. [...]

Switching Commands 31 ProSafe M4100 and M7100 Managed Switches no spanning-tree bpdufilter Use this command to disable BPDU Filter on the interface or range of interfaces. Default Format no spanning-tree bpdufilter Mode spanning -tree bpdufilter default Use this command to enable BPDU Filter on all the edge port interfaces. Default Format spanning-[...]

Switching Commands 32 ProSafe M4100 and M7100 Managed Switches spanning -tree bpduguard Use this command to enable BPDU Guard on the switch. Default Format spanning-tree bpduguard Mode no spanning-tree bpduguard Use this command to disable BPDU Guard on the switch. Format no spanning-tree bpduguard Mode spanning -tree bpdumigrationcheck Use this co[...]

Switching Commands 33 ProSafe M4100 and M7100 Managed Switches spanning -tree configuration revision This command sets the Configuration Identifier Revision Level for use in identifying the configuration that this switch is currently using. The Configuration Identifier Revision Level is a number in the range of 0–65535. Default Format spanning-tr[...]

Switching Commands 34 ProSafe M4100 and M7100 Managed Switches • Use 802.1s to specify that the switch transmits MST BPDUs (IEEE 802.1s functionality supported). • Use 802.1w to specify that the switch transmits RST BPDUs rather than MST BPDUs (IEEE 802.1w functionality supported). no spanning-tree forceversion This command sets the Force Proto[...]

Switching Commands 35 ProSafe M4100 and M7100 Managed Switches spanning -tree tcnguard This command enables the propagation of received topology change notifications and topology changes to other ports. Default Format spanning-tree tcnguard Mode no spanning-tree tcnguard This command disables the propagation of received topology change notification[...]

Switching Commands 36 ProSafe M4100 and M7100 Managed Switches no spanning-tree max-hops This command sets the Bridge Max Hops parameter for the Common and Internal Spanning T ree to the default value. Format no spanning-tree max-hops Mode spanning -tree mst This command sets the Path Cost or Port Priority for this port within the multiple spanning[...]

Switching Commands 37 ProSafe M4100 and M7100 Managed Switches If you specify cost , this command sets the path cost for this port within a multiple spanning tree instance or the Common and Internal Spanning T ree instance, depending on the <mstid> parameter , to the default value, that is, a path cost value based on the Link Speed. If you sp[...]

Switching Commands 38 ProSafe M4100 and M7100 Managed Switches are masked according to the 802.1s specification. This causes the priority to be rounded down to the next lower valid priority . Default Format spanning-tree mst priority <mstid> <0-61440> Mode no spanning-tree mst priority This command sets the bridge priority for a specifi[...]

Switching Commands 39 ProSafe M4100 and M7100 Managed Switches spanning -tree port mode This command sets the Administrative Switch Port State for this port to enabled. Default Format spanning-tree port mode Mode no spanning-tree port mode This command sets the Administrative Switch Port State for this port to disabled. Format no spanning-tree port[...]

Switching Commands 40 ProSafe M4100 and M7100 Managed Switches spanning -tree bpduforwarding Normally a switch will not forward Spanning T ree Protocol (STP) BPDU packets if STP is disabled. However , if in some network setup, the user wishes to forward BDPU packets received from other network devices, this command can be used to enable the forward[...]

Switching Commands 41 ProSafe M4100 and M7100 Managed Switches show spanning -tree brief This command displays spanning tree settings for the bridge. The following information appears. Format show spanning-tree brief Mode • Privileged EXEC • User EXEC Bridge Priority Bridge Identifier Bridge Max Age Bridge Max Hops Bridge Hello Time Bridge Forw[...]

Switching Commands 42 ProSafe M4100 and M7100 Managed Switches show spanning -tree interface This command displays the settings and parameters for a specific switch port within the Common and Internal Spanning T ree. The <slot/port > is the desired switch port. The following details are displayed on execution of the command. Format show spann[...]

Switching Commands 43 ProSafe M4100 and M7100 Managed Switches corresponds to the desired existing multiple spanning tree instance. The <slot/port > is the desired switch port. Format show spanning-tree mst port detailed <mstid> <slot/port> Mode • Privileged EXEC • User EXEC MST Instance ID Port Identifier Port Priority Port F[...]

Switching Commands 44 ProSafe M4100 and M7100 Managed Switches If you specify 0 (defined as the default CIST ID) as the <mstid> , this command displays the settings and parameters for a specific switch port within the Common and Internal Spanning T ree. The <slot/port > is the desired switch port. In this case, the following are display[...]

Switching Commands 45 ProSafe M4100 and M7100 Managed Switches show spanning -tree mst port summary This command displays the settings of one or all ports within the specified multiple spanning tree instance. The parameter <mstid> indicates a particular MST instance. The parameter { <slot/port > | all} indicates the desired switch port [...]

Switching Commands 46 ProSafe M4100 and M7100 Managed Switches show spanning -tree mst summary This command displays summary information about all multiple spanning tree instances in the switch. On execution, the following details are displayed. Format show spanning-tree mst summary Mode • Privileged EXEC • User EXEC MST Instance ID List For ea[...]

Spanning Tree Adminmode Spanning Tree Version BPDU Guard Mode BPDU Filter Mode Configuration Name Configuration Revision Level Configuration Digest Key Configuration Format Selector MST Instances Switching Commands 47 ProSafe M4100 and M7100 Managed Switches show spanning -tree vlan This command displays the association between a VLAN and a multipl[...]

Switching Commands 48 ProSafe M4100 and M7100 Managed Switches vlan database This command gives you access to the VLAN Config mode, which allows you to configure VLAN characteristics. Format vlan database Mode network mgmt_vlan This command configures the Management VLAN ID. Default Format network mgmt_vlan <1-4093> Mode no network mgmt_vlan [...]

Switching Commands 49 ProSafe M4100 and M7100 Managed Switches vlan acceptframe This command sets the frame acceptance mode per interface. For VLAN Only mode, untagged frames or priority frames received on this interface are discarded. For Admit All mode, untagged frames or priority frames received on this interface are accepted and assigned the va[...]

Switching Commands 50 ProSafe M4100 and M7100 Managed Switches vlan makestatic This command changes a dynamically created VLAN (one that is created by GVRP registration) to a static VLAN (one that is permanently configured and defined). The ID is a valid VLAN identification number . VLAN range is 2-4093. Format vlan makestatic <2-4093> Mode v[...]

Switching Commands 51 ProSafe M4100 and M7100 Managed Switches vlan participation all This command configures the degree of participation for all interfaces in a VLAN. The ID is a valid VLAN identification number . Format vlan participation all {exclude | include | auto} <1-4093> Mode Y ou can use the following participation options: include [...]

Switching Commands 52 ProSafe M4100 and M7100 Managed Switches assigned the value of the interface VLAN ID for this port. With either option, VLAN tagged frames are forwarded in accordance with the IEEE 802.1Q VLAN Specification. Format no vlan port acceptframe all Mode vlan port ingressfilter all This command enables ingress filtering for all port[...]

Switching Commands 53 ProSafe M4100 and M7100 Managed Switches vlan port tagging all This command configures the tagging behavior for all interfaces in a VLAN to enabled. If tagging is enabled, traffic is transmitted as tagged frames. If tagging is disabled, traf fic is transmitted as untagged frames. The ID is a valid VLAN identification number . [...]

Switching Commands 54 ProSafe M4100 and M7100 Managed Switches no vlan protocol group name This command removes the name from a protocol-based VLAN group. Format no vlan protocol group name <1-128> Mode vlan protocol group add protocol This command adds the protocol to the protocol-based VLAN identified by groupid. A group may have more than [...]

Switching Commands 55 ProSafe M4100 and M7100 Managed Switches no protocol group This command removes the <vlanid> from this protocol-based VLAN group that is identified by this <groupid> . Format no protocol group <groupid> <vlanid> Mode protocol vlan group This command adds the physical interface to the protocol-based VLAN[...]

Switching Commands 56 ProSafe M4100 and M7100 Managed Switches no protocol vlan group all This command removes all interfaces from this protocol-based VLAN group that is identified by this <groupid> . Format no protocol vlan group all <groupid> Mode vlan pvid This command changes the VLAN ID per interface. Default Format vlan pvid <1[...]

Switching Commands 57 ProSafe M4100 and M7100 Managed Switches vlan association subnet This command associates a VLAN to a specific IP-subnet. Format vlan association subnet <ipaddr> <netmask> <1-4093> Mode no vlan association subnet This command removes association of a specific IP-subnet to a VLAN. Format no vlan association sub[...]

Switching Commands 58 ProSafe M4100 and M7100 Managed Switches show vlan <vlanid> This command displays detailed information, including interface information, for a specific VLAN. The ID is a valid VLAN identification number . Format show vlan <vlanid> Mode • Privileged EXEC • User EXEC VLAN ID VLAN Name VLAN Type Interface Current [...]

Switching Commands 59 ProSafe M4100 and M7100 Managed Switches show vlan brief This command displays a list of all configured VLANs. Format show vlan brief Mode • Privileged EXEC • User EXEC VLAN ID VLAN Name VLAN Type show vlan port This command displays VLAN port information. Format show vlan port {<slot/port> | all} Mode • Privileged[...]

Switching Commands 60 ProSafe M4100 and M7100 Managed Switches show vlan association subnet This command displays the VLAN associated with a specific configured IP-Address and net mask. If no IP address and net mask are specified, the VLAN associations of all the configured IP-subnets are displayed. Format show vlan association subnet [<ipaddr&g[...]

Switching Commands 61 ProSafe M4100 and M7100 Managed Switches dvlan-tunnel ethertype This command configures the ether-type for all interfaces. The ether-type may have the values of 802.1Q , vMAN , or custom . If the ether-type has a value of custom , the optional value of the custom ether type must be set to a value from 0 to 65535. Default Forma[...]

Switching Commands 62 ProSafe M4100 and M7100 Managed Switches no mode dvlan-tunnel This command is used to disable Double VLAN T unneling on the specified interface. By default, Double VLAN T unneling is disabled. Format no mode dvlan-tunnel Mode show dot1q-tunnel Use this command without the optional parameters to display all interfaces enabled f[...]

Switching Commands 63 ProSafe M4100 and M7100 Managed Switches V oice VLAN Commands This section describes the commands you use for V oice VLAN. V oice VLAN enables switch ports to carry voice traffic with defined priority to enable separation of voice and data traf fic coming onto the port. The benefits of using V oice VLAN is to ensure that the s[...]

Switching Commands 64 ProSafe M4100 and M7100 Managed Switches Y ou can configure V oice VLAN in any of the following ways: vlan-id dot1p none untagged no voice vlan (Interface Config) Use this command to disable the V oice VLAN capability on the interface. Format no voice vlan Mode voice vlan data priority Use this command to either trust or untru[...]

Switching Commands 65 ProSafe M4100 and M7100 Managed Switches When the interface is specified: Voice VLAN Interface Mode Voice VLAN ID Voice VLAN Priority Voice VLAN Untagged Voice VLAN CoS Override Voice VLAN Status . P rovisioning (IEEE 802.1p) Commands This section describes the commands you use to configure provisioning, which allows you to pr[...]

Switching Commands 66 ProSafe M4100 and M7100 Managed Switches If an interface is configured as a protected port, and you add that interface to a Port Channel or link aggregation group (LAG), the protected port status becomes operationally disabled on the interface, and the interface follows the configuration of the LAG port. However , the protecte[...]

Switching Commands 67 ProSafe M4100 and M7100 Managed Switches no switchport protected (Interface Config) Use this command to configure a port as unprotected. The groupid parameter identifies the set of protected ports to which this interface is assigned. Format no switchport protected <groupid> Mode show switchport protected This command dis[...]

Switching Commands 68 ProSafe M4100 and M7100 Managed Switches P rivate VLAN The Private VLANs feature separates a regular VLAN domain into two or more subdomains. Each subdomain is defined (represented) by a primary VLAN and a secondary VLAN. The primary VLAN ID is the same for all subdomains that belong to a private VLAN. The secondary VLAN ID di[...]

host-association mapping primary-vlan-id secondary-vlan-id add remove secondary-vlan-list Switching Commands 69 ProSafe M4100 and M7100 Managed Switches no switchport private-vlan This command is used to remove the private-VLAN association or mapping from the port. switchport mode private-vlan This command is used to configure a port as a promiscuo[...]

Switching Commands 70 ProSafe M4100 and M7100 Managed Switches private-vlan This command is used to configure the private VLANs and to configure the association between the primary private VLAN and secondary VLANs. Format private-vlan {association [add | remove] <secondary-vlan-list> | community | isolated | primary} Mode association secondar[...]

Private -vlan type Primary Secondary Type Ports Switching Commands 71 ProSafe M4100 and M7100 Managed Switches show interface ethernet <slot/port > switchport This command displays the private-VLAN mapping information for the switch interfaces. Format show interface ethernet <slot/port> switchport Mode • Privileged EXEC • User EXEC [...]

Switching Commands 72 ProSafe M4100 and M7100 Managed Switches no set garp timer join This command sets the GVRP join time (for one or all ports and per GARP) to the default and only has an ef fect when GVRP is enabled. Format no set garp timer join Mode • Interface Config • Global Config set garp timer leave This command sets the GVRP leave ti[...]

Switching Commands 73 ProSafe M4100 and M7100 Managed Switches no set garp timer leaveall This command sets how frequently Leave All PDUs are generated the default and only has an ef fect when GVRP is enabled. Format no set garp timer leaveall Mode • Interface Config • Global Config show garp This command displays GARP information. Format show [...]

Switching Commands 74 ProSafe M4100 and M7100 Managed Switches no set gvrp adminmode This command disables GVRP . Format no set gvrp adminmode Mode set gvrp interfacemode This command enables GVRP on a single port (Interface Config mode) or all ports (Global Config mode). Default Format set gvrp interfacemode Mode • Interface Config • Global Co[...]

Switching Commands 75 ProSafe M4100 and M7100 Managed Switches GMRP Commands This section describes the commands you use to configure and view GARP Multicast Registration Protocol (GMRP) information. Like IGMP snooping, GMRP helps control the flooding of multicast packets. GMRP-enabled switches dynamically register and deregister group membership i[...]

Switching Commands 76 ProSafe M4100 and M7100 Managed Switches set gmrp interfacemode This command enables GARP Multicast Registration Protocol on a single interface (Interface Config mode) or all interfaces (Global Config mode). If an interface which has GARP enabled is enabled for routing or is enlisted as a member of a port-channel (LAG), GARP f[...]

Switching Commands 77 ProSafe M4100 and M7100 Managed Switches show mac-address-table gmrp This command displays the GMRP entries in the Multicast Forwarding Database (MFDB) table. Format show mac-address-table gmrp Mode Mac Address Type Description Interfaces P ort -Based Network Access Control Commands This section describes the commands you use [...]

Switching Commands 78 ProSafe M4100 and M7100 Managed Switches clear dot1x statistics This command resets the 802.1x statistics for the specified port or for all ports. Format clear dot1x statistics {<slot/port> | all} Mode clear radius statistics This command is used to clear all RADIUS statistics. Format clear radius statistics Mode dot1x e[...]

Switching Commands 79 ProSafe M4100 and M7100 Managed Switches no dot1x guest-vlan This command disables Guest VLAN on the interface. Default Format no dot1x guest-vlan Mode dot1x initialize This command begins the initialization sequence on the specified port. This command is only valid if the control mode for the specified port is “auto” or ?[...]

Switching Commands 80 ProSafe M4100 and M7100 Managed Switches no dot1x max-req This command sets the maximum number of times the authenticator state machine on this port will transmit an EAPOL EAP Request/Identity frame before timing out the supplicant. Format no dot1x max-req Mode dot1x max -users Use this command to set the maximum number of cli[...]

Switching Commands 81 ProSafe M4100 and M7100 Managed Switches no dot1x port-control This command sets the 802.1x port control mode on the specified port to the default value. Format no dot1x port-control Mode dot1x port - control all This command sets the authentication mode to use on all ports. Select force-unauthorized to specify that the authen[...]

Switching Commands 82 ProSafe M4100 and M7100 Managed Switches no dot1x re-authentication This command disables re-authentication of the supplicant for the specified port. Format no dot1x re-authentication Mode dot1x system-auth-control Use this command to enable the dot1x authentication support on the switch. While disabled, the dot1x configuratio[...]

Switching Commands 83 ProSafe M4100 and M7100 Managed Switches no dot1x timeout This command sets the value, in seconds, of the timer used by the authenticator state machine on this port to the default values. Depending on the token used, the corresponding default values are set. Format no dot1x timeout {guest-vlan-period | reauth-period | quiet-pe[...]

Switching Commands 84 ProSafe M4100 and M7100 Managed Switches no dot1x unauthenticated-vlan This command resets the unauthenticated-vlan associated with the port to its default value. Format no dot1x unauthenticated-vlan Mode dot1x user This command adds the specified user to the list of users with access to the specified port or all ports. The &l[...]

Switching Commands 85 ProSafe M4100 and M7100 Managed Switches no dot1x dynamic-vlan enable Use this command to disable the switch from creating VLANs dynamically when a RADIUS assigned VLAN does not exist in the switch. Format no dot1x dynamic-vlan enable Mode dot1x system-auth-control monitor Use this command to enable the 802.1X monitor mode on [...]

Switching Commands 86 ProSafe M4100 and M7100 Managed Switches show authentication methods This command displays information about the authentication methods. Format show authentication methods Mode The following is an example of this command: Login Authentication Method Lists ________________________________ Console_Default: None Network_Default:L[...]

Switching Commands 87 ProSafe M4100 and M7100 Managed Switches If you do not use the optional parameters <slot/port> or <vlanid> , the command displays the global dot1x mode, the VLAN Assignment mode, and the Dynamic VLAN Creation mode. Administrative Mode VLAN Assignment Mode Dynamic VLAN Creation Mode Monitor Mode If you use the optio[...]

Switching Commands 88 ProSafe M4100 and M7100 Managed Switches Backend Authentication State Current state of the backend authentication state machine. Possible values are Request, Response, Success, Fail, T imeout, Idle, and Initialize. When MAC-based authentication is enabled on the port, this parameter is deprecated. Quiet Period The timer used b[...]

Switching Commands 89 ProSafe M4100 and M7100 Managed Switches The show dot1x detail <slot/port> command will display the following MAC-based dot1x fields if the port-control mode for that specific port is MAC-based. For each client authenticated on the port, the show dot1x detail <slot/port> command will display the following MAC-based[...]

Switching Commands 90 ProSafe M4100 and M7100 Managed Switches show dot1x clients This command displays 802.1x client information. This command also displays information about the number of clients that are authenticated using Monitor mode and using 802.1X. Format show dot1x clients { <slot/port> | all} Mode Last EAPOL Frame Source The source[...]

Switching Commands 91 ProSafe M4100 and M7100 Managed Switches show dot1x users This command displays 802.1x port security user information for locally configured users. Format show dot1x users <slot/port> Mode Users 802.1X Supplicant Commands 802.1X (“dot1x”) supplicant functionality is on point-to-point ports. The administrator can conf[...]

Switching Commands 92 ProSafe M4100 and M7100 Managed Switches dot1x supplicant port - control Use this command to set the ports authorization state (Authorized or Unauthorized) either manually or by setting the port to auto-authorize upon startup. By default all the ports are authenticators. If the port’s attribute needs to be moved from <aut[...]

Switching Commands 93 ProSafe M4100 and M7100 Managed Switches dot1x supplicant timeout start -period Use this command to configure the start period timer interval to wait for the EAP identity request from the authenticator . Default Format dot1x supplicant timeout start-period < 1-65535 seconds > Mode no dot1x supplicant timeout start-period[...]

Switching Commands 94 ProSafe M4100 and M7100 Managed Switches no dot1x supplicant timeout auth-period Use this command to set the auth-period value to the default value. Format no dot1x supplicant timeout auth-period Mode dot1x supplicant user Use this command to map the given user to the port. Format dot1x supplicant user Mode Storm- Control Comm[...]

Switching Commands 95 ProSafe M4100 and M7100 Managed Switches rate kbps. For example, if the configured limit is 10%, this is converted to ~25000 pps, and this pps limit is set in forwarding plane (hardware). Y ou get the approximate desired output when 512bytes packets are used. storm-control broadcast Use this command to enable broadcast storm r[...]

Switching Commands 96 ProSafe M4100 and M7100 Managed Switches no storm-control broadcast level This command sets the broadcast storm recovery threshold to the default value for an interface and disables broadcast storm recovery . Format no storm-control broadcast level Mode storm-control broadcast rate Use this command to configure the broadcast s[...]

Switching Commands 97 ProSafe M4100 and M7100 Managed Switches storm-control broadcast level (Global) This command configures the broadcast storm recovery threshold for all interfaces as a percentage of link speed and enables broadcast storm recovery . If the mode is enabled, broadcast storm recovery is active, and if the rate of L2 broadcast traff[...]

Switching Commands 98 ProSafe M4100 and M7100 Managed Switches storm-control multicast This command enables multicast storm recovery mode for an interface. If the mode is enabled, multicast storm recovery is active, and if the rate of L2 multicast traffic ingressing on an interface increases beyond the configured threshold, the traffic will be drop[...]

Switching Commands 99 ProSafe M4100 and M7100 Managed Switches the traffic is dropped. Therefore, the rate of multicast traffic is limited to the configured threshold. Default Format storm-control multicast rate <0-14880000> Mode no storm-control multicast rate This command sets the multicast storm recovery threshold to the default value for [...]

Switching Commands 100 ProSafe M4100 and M7100 Managed Switches no storm-control multicast level This command sets the multicast storm recovery threshold to the default value for all interfaces and disables multicast storm recovery . Format no storm-control multicast level Mode storm-control multicast rate (Global) Use this command to configure the[...]

Switching Commands 101 ProSafe M4100 and M7100 Managed Switches no storm-control unicast This command disables unicast storm recovery mode for an interface. Format no storm-control unicast Mode storm-control unicast level This command configures the unicast storm recovery threshold for an interface as a percentage of link speed, and enables unicast[...]

Switching Commands 102 ProSafe M4100 and M7100 Managed Switches no storm-control unicast rate This command sets the unicast storm recovery threshold to the default value for an interface and disables unicast storm recovery . Format no storm-control unicast rate Mode storm-control unicast (Global) This command enables unicast storm recovery mode for[...]

Switching Commands 103 ProSafe M4100 and M7100 Managed Switches no storm-control unicast level This command sets the unicast storm recovery threshold to the default value and disables unicast storm recovery for all interfaces. Format no storm-control unicast level Mode storm-control unicast rate (Global) Use this command to configure the unicast st[...]

Switching Commands 104 ProSafe M4100 and M7100 Managed Switches Use the all keyword to display the per-port configuration parameters for all interfaces, or specify the slot/port to display information about a specific interface. Format show storm-control [all | <slot/port>] Mode Bcast Mode Bcast Level Mcast Mode Mcast Level Ucast Mode Ucast L[...]

Switching Commands 105 ProSafe M4100 and M7100 Managed Switches no flowcontrol Format no flowcontrol Mode • Global Config • Interface Config show flowcontrol Use this command to display the IEEE 802.3 Annex 31B flow control settings and status for a specific interface or all interfaces. It also displays 802.3 Tx and Rx pause counts. Priority Fl[...]

Switching Commands 106 ProSafe M4100 and M7100 Managed Switches A port-channel (LAG) interface can be either static or dynamic, but not both. All members of a port channel must participate in the same protocols.) A static port-channel interface does not require a partner system to be able to aggregate its member ports. Note: If you configure the ma[...]

Switching Commands 107 ProSafe M4100 and M7100 Managed Switches lacp admin key Use this command to configure the administrative value of the key for the port-channel. The value range of < key > is 0–65535. Default Format lacp admin key < key > Mode Note: This command is only applicable to port-channel interfaces. no lacp admin key Use[...]

Switching Commands 108 ProSafe M4100 and M7100 Managed Switches lacp actor admin key Use this command to configure the administrative value of the LACP actor admin key . The valid range for < key > is 0-65535. Default Format lacp actor admin key < key > Mode Note: This command is only applicable to physical interfaces. no lacp actor adm[...]

Switching Commands 109 ProSafe M4100 and M7100 Managed Switches Note: This command is only applicable to physical interfaces. no lacp actor admin state longtimeout Use this command to set the LACP actor admin state to short timeout. Format no lacp actor admin state longtimeout Mode Note: This command is only applicable to physical interfaces. lacp [...]

Switching Commands 11 0 ProSafe M4100 and M7100 Managed Switches no lacp actor port priority Use this command to configure the default priority value assigned to the Aggregation Port. Format no lacp actor port priority Mode lacp actor system priority Use this command to configure the priority value associated with the LACP Actor ’s SystemID. The [...]

Switching Commands 111 ProSafe M4100 and M7100 Managed Switches no lacp partner admin key Use this command to configure the administrative value of the Key for the protocol partner . Format no lacp partner admin key < key > Mode lacp partner admin state individual Use this command to set LACP partner admin state to individual. Format lacp par[...]

Switching Commands 11 2 ProSafe M4100 and M7100 Managed Switches lacp partner admin state passive Use this command to set the LACP partner admin state to passive. Format lacp partner admin state passive Mode Note: This command is only applicable to physical interfaces. no lacp partner admin state passive Use this command to set the LACP partner adm[...]

Switching Commands 11 3 ProSafe M4100 and M7100 Managed Switches Note: This command is only applicable to physical interfaces. no lacp partner port priority Use this command to configure the default LACP partner port priority . Format no lacp partner port priority Mode lacp partner system id Use this command to configure the 6-octet MAC Address val[...]

Switching Commands 11 4 ProSafe M4100 and M7100 Managed Switches Note: This command is applicable only to physical interfaces. no lacp partner system priority Use this command to configure the default administrative value of priority associated with the Partner ’s System ID. Format no lacp partner system priority Mode port - channel local-prefere[...]

Switching Commands 11 5 ProSafe M4100 and M7100 Managed Switches no port-channel static This command sets the static mode on a particular port-channel (LAG) interface to the default value. This command will be executed only for interfaces of type port-channel (LAG). Format no port-channel static Mode port lacpmode This command enables Link Aggregat[...]

Switching Commands 11 6 ProSafe M4100 and M7100 Managed Switches no port lacptimeout This command sets the timeout back to its default value on a physical interface of a particular device type ( actor or partner ). Format no port lacptimeout {actor | partner} Mode port lacptimeout (Global Config) This command sets the timeout for all interfaces of [...]

Switching Commands 11 7 ProSafe M4100 and M7100 Managed Switches port - channel linktrap This command enables link trap notifications for the port-channel (LAG). The interface is a logical slot/port for a configured port-channel. The option all enables link trap notifications for all the configured port-channels. Default Format port-channel linktra[...]

1 2 3 4 5 6 7 <slot/port>| all Switching Commands 11 8 ProSafe M4100 and M7100 Managed Switches no port-channel load-balance This command reverts to the default load balancing configuration. port - channel name This command defines a name for the port-channel (LAG). The interface is a logical slot/port for a configured port-channel, and <n[...]

Switching Commands 11 9 ProSafe M4100 and M7100 Managed Switches no port-channel system priority Use this command to configure the default port-channel system priority value. Format no port-channel system priority Mode show lacp actor Use this command to display LACP actor attributes. Format show lacp actor {< slot/port >|all} Mode The follow[...]

Switching Commands 120 ProSafe M4100 and M7100 Managed Switches show port - channel brief This command displays the static capability of all port-channel (LAG) interfaces on the device as well as a summary of individual port-channel interfaces. Format show port-channel brief Mode • Privileged EXEC • User EXEC For each port-channel the following[...]

Switching Commands 121 ProSafe M4100 and M7100 Managed Switches show port - channel system priority Use this command to display the port-channel system priority . Format show port-channel system priority Mode P ort Mirroring Port mirroring, which is also known as port monitoring, selects network traffic that you can analyze with a network analyzer [...]

Switching Commands 122 ProSafe M4100 and M7100 Managed Switches no monitor session Use this command without optional parameters to remove the monitor session (port monitoring) designation from the source probe port, the destination monitored port and all VLANs. Once the port is removed from the VLAN, you must manually add the port to any desired VL[...]

Switching Commands 123 ProSafe M4100 and M7100 Managed Switches Static MA C Filtering The commands in this section describe how to configure static MAC filtering. Static MAC filtering allows you to configure destination ports for a static multicast MAC filter irrespective of the platform. macfilter This command adds a static MAC filter entry for th[...]

Switching Commands 124 ProSafe M4100 and M7100 Managed Switches no macfilter This command removes all filtering restrictions and the static MAC filter entry for the MAC address <macaddr> on the VLAN <vlanid> . The <macaddr> parameter must be specified as a 6-byte hexadecimal number in the format of b1:b2:b3:b4:b5:b6. The <vlani[...]

Switching Commands 125 ProSafe M4100 and M7100 Managed Switches 6-byte hexadecimal number in the format of b1:b2:b3:b4:b5:b6. The <vlanid> parameter must identify a valid VLAN. Note: Configuring a destination port list is only valid for multicast MAC addresses. no macfilter adddest all This command removes all ports from the destination filte[...]

Switching Commands 126 ProSafe M4100 and M7100 Managed Switches 6-byte hexadecimal number in the format of b1:b2:b3:b4:b5:b6. The <vlanid> parameter must identify a valid VLAN. Format macfilter addsrc all <macaddr> <vlanid> Mode no macfilter addsrc all This command removes all interfaces to the source filter set for the MAC filter[...]

Mac Address Type Description Interfaces Switching Commands 127 ProSafe M4100 and M7100 Managed Switches DHCP L2 R elay Agent Commands Y ou can enable the switch to operate as a DHCP Layer 2 relay agent to relay DHCP requests from clients to a Layer 3 relay agent or server . The Circuit ID and Remote ID can be added to DHCP requests relayed from cli[...]

Switching Commands 128 ProSafe M4100 and M7100 Managed Switches Separate non-consecutive IDs with a comma (,), and do not insert spaces or zeros in between the range. Use a dash (–) for the range. Format dhcp l2relay circuit-id vlan < vlan-list > Mode no dhcp l2relay circuit-id vlan Use this parameter to clear the DHCP Option-82 Circuit ID [...]

Switching Commands 129 ProSafe M4100 and M7100 Managed Switches no dhcp l2relay vlan Use this command to disable the DHCP L2 Relay agent for a set of VLANs. Format no dhcp l2relay vlan < vlan-list > Mode dhcp l2relay trust Use this command to configure an interface or range of interfaces as trusted for Option-82 reception. Default Format dhcp[...]

Switching Commands 130 ProSafe M4100 and M7100 Managed Switches show dhcp l2relay interface Use this command to display DHCP L2 relay configuration specific to interfaces. Format show dhcp l2relay interface {all | interface-num } Mode Example: The following shows example CLI display output for the command. (switch) #show dhcp l2relay interface all [...]

Switching Commands 131 ProSafe M4100 and M7100 Managed Switches 5 Enabled Enabled --NULL— 6 Enabled Enabled netgear 7 Enabled Disabled --NULL— 8 Enabled Disabled --NULL— 9 Enabled Disabled --NULL— 10 Enabled Disabled --NULL-- DHCP Client Commands DHCP Client can include vendor and configuration information in DHCP client requests relayed to[...]

Switching Commands 132 ProSafe M4100 and M7100 Managed Switches show dhcp client vendor -id- option Use this command to display the configured administration mode of the vendor-id-option and the vendor-id string to be included in Option-43 in DHCP requests. Format show dhcp client vendor-id-option Mode Example: The following shows example CLI displ[...]

Switching Commands 133 ProSafe M4100 and M7100 Managed Switches no ip dhcp snooping vlan Use this command to disable DHCP Snooping on VLANs. Format no ip dhcp snooping vlan < vlan-list > Mode ip dhcp snooping verify mac-address Use this command to enable verification of the source MAC address with the client hardware address in the received D[...]

Switching Commands 134 ProSafe M4100 and M7100 Managed Switches no ip dhcp snooping database write-delay Use this command to set the write delay value to the default value. Format no ip dhcp snooping database write-delay Mode ip dhcp snooping binding Use this command to configure static DHCP Snooping binding. Format ip dhcp snooping binding < ma[...]

Switching Commands 135 ProSafe M4100 and M7100 Managed Switches no ip dhcp snooping limit Use this command to set the rate at which the DHCP Snooping messages come, and the burst level, to the defaults. Format no ip dhcp snooping limit Mode ip dhcp snooping log -invalid Use this command to control the logging DHCP messages filtration by the DHCP Sn[...]

Switching Commands 136 ProSafe M4100 and M7100 Managed Switches ip verify source Use this command to configure the IPSG source ID attribute to filter the data traffic in the hardware. Source ID is the combination of IP address and MAC address. Normal command allows data traffic filtration based on the IP address. With the “port-security” option[...]

Switching Commands 137 ProSafe M4100 and M7100 Managed Switches 0/1 Yes No 0/2 No Yes 0/3 No Yes 0/4 No No 0/6 No No show ip dhcp snooping binding Use this command to display the DHCP Snooping binding entries. T o restrict the output, use the following options: • Dynamic: Restrict the output based on DCHP snooping. • Interface: Restrict the out[...]

Switching Commands 138 ProSafe M4100 and M7100 Managed Switches show ip dhcp snooping database Use this command to display the DHCP Snooping configuration related to the database persistency . Format show ip dhcp snooping database Mode • Privileged EXEC • User EXEC Example: The following shows example CLI display output for the command. (switch[...]

Switching Commands 139 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. (switch) #show ip dhcp snooping statistics Interface MAC Verify Client Ifc DHCP Server Failures Mismatch Msgs Rec'd ----------- ---------- ---------- ----------- 0/2 0 0 0 0/3 0 0 0 0/4 0 0 0 0/5 0 0 0 0/6 0 [...]

Switching Commands 140 ProSafe M4100 and M7100 Managed Switches show ip verify source Use this command to display the IPSG configurations on all ports. Format show ip verify source Mode • Privileged EXEC • User EXEC Example: The following shows example CLI display output for the command. (switch) #show ip verify source Interface Filter Type IP [...]

Switching Commands 141 ProSafe M4100 and M7100 Managed Switches The following shows sample CLI display output for the command. (switch) #show ip source binding MAC Address IP Address Type Vlan Interface ----------------- --------------- ------------- ----- ------------- 00:00:00:00:00:08 1.2.3.4 dhcp-snooping 2 0/1 00:00:00:00:00:09 1.2.3.4 dhcp-sn[...]

Switching Commands 142 ProSafe M4100 and M7100 Managed Switches ip arp inspection validate Use this command to enable additional validation checks like source-mac validation, destination-mac validation, and ip address validation on the received ARP packets. Each command overrides the configuration of the previous command. For example, if a command [...]

Switching Commands 143 ProSafe M4100 and M7100 Managed Switches no ip arp inspection trust Use this command to configure an interface as untrusted for Dynamic ARP Inspection. Format no ip arp inspection trust Mode ip arp inspection limit Use this command to configure the rate limit and burst interval values for an interface. Configuring none for th[...]

Switching Commands 144 ProSafe M4100 and M7100 Managed Switches no ip arp inspection filter Use this command to unconfigure the ARP ACL used to filter invalid ARP packets on a list of comma-separated VLAN ranges. Format no ip arp inspection filter acl-name vlan vlan-list [static] Mode arp access-list Use this command to create an ARP ACL. Format ar[...]

Switching Commands 145 ProSafe M4100 and M7100 Managed Switches the given VLAN list. The global configuration includes the source mac validation , destination mac validation, and invalid IP validation information. Format show ip arp inspection [vlan < vlan-list> ] Mode • Privileged EXEC • User EXEC Example: The following shows example CLI[...]

Switching Commands 146 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command show ip arp inspection statistics which lists the summary of forwarded and dropped ARP packets on all DAI-enabled VLANs. VLAN Forwarded Dropped ---- --------- ------- 10 90 14 20 10 3 Example: The following shows e[...]

Switching Commands 147 ProSafe M4100 and M7100 Managed Switches command displays the values for that interface whether the interface is enabled for DAI or not. Format show ip arp inspection interfaces [slot/port] Mode • Privileged EXEC • User EXEC Example: The following shows example CLI display output for the command. (Switch) #show ip arp ins[...]

Switching Commands 148 ProSafe M4100 and M7100 Managed Switches IGMP Snooping Configuration Commands This section describes the commands you use to configure IGMP snooping. The software supports IGMP V ersions 1, 2, and 3. The IGMP snooping feature can help conserve bandwidth because it allows the switch to forward IP multicast traffic only to conn[...]

Format no set igmp <vlanid> Mode Switching Commands 149 ProSafe M4100 and M7100 Managed Switches set igmp interfacemode This command enables IGMP Snooping on all interfaces. If an interface has IGMP Snooping enabled and you enable this interface for routing or enlist it as a member of a port-channel (LAG), IGMP Snooping functionality is disab[...]

Switching Commands 150 ProSafe M4100 and M7100 Managed Switches no set igmp fast-leave This command disables IGMP Snooping fast-leave admin mode on a selected interface. Format no set igmp fast-leave Mode Format no set igmp fast-leave <vlan_id> Mode set igmp groupmembership-interval This command sets the IGMP Group Membership Interval time on[...]

Switching Commands 151 ProSafe M4100 and M7100 Managed Switches particular group in that interface. This value must be less than the IGMP Query Interval time value. The range is 1–25 seconds. Default Format set igmp maxresponse <1-25> Mode • Global Config • Interface Config Format set igmp maxresponse <vlan_id> <1-25> Mode n[...]

Switching Commands 152 ProSafe M4100 and M7100 Managed Switches no set igmp mcrtrexpiretime This command sets the Multicast Router Present Expiration time to 0. The time is set for the system, on a particular interface or a VLAN. Format no set igmp mcrtrexpiretime Mode • Global Config • Interface Config Format no set igmp mcrtrexpiretime <vl[...]

Switching Commands 153 ProSafe M4100 and M7100 Managed Switches set igmp report - suppression Use this command to suppress the IGMP reports on a given VLAN ID. In order to optimize the number of reports traversing the network with no added benefits, a Report Suppression mechanism is implemented. When more than one client responds to an MGMD query f[...]

Switching Commands 154 ProSafe M4100 and M7100 Managed Switches mac address-table multicast forbidden-unregistered vlan Use this command to forbid forwarding unregistered multicast addresses (in other words, unknown multicast traffic) on a given VLAN ID. Default Format mac address-table multicast forbidden-unregistered vlan < 1-4093 > Mode no[...]

Switching Commands 155 ProSafe M4100 and M7100 Managed Switches show igmpsnooping This command displays IGMP Snooping information. Configured information is displayed whether or not IGMP Snooping is enabled. Format show igmpsnooping [<slot/port> | <vlan_id>] Mode When the optional arguments <slot/port > or <vlan_id> are not [...]

Switching Commands 156 ProSafe M4100 and M7100 Managed Switches show igmpsnooping mrouter interface This command displays information about statically configured ports. Format show igmpsnooping mrouter interface <slot/port> Mode Interface Multicast Router Attached VLAN ID show igmpsnooping mrouter vlan This command displays information about [...]

Switching Commands 157 ProSafe M4100 and M7100 Managed Switches show mac-address-table igmpsnooping This command displays the IGMP Snooping entries in the MFDB table. Format show mac-address-table igmpsnooping Mode MAC Address Type Description Interfaces show mac address-table multicast filtering Use this command to display the multicast filtering [...]

Switching Commands 158 ProSafe M4100 and M7100 Managed Switches set igmp querier Use this command to enable IGMP Snooping Querier on the system, using Global Config mode, or on a VLAN. Using this command, you can specify the IP Address that the Snooping Querier switch should use as the source address while generating periodic queries. If a VLAN has[...]

Switching Commands 159 ProSafe M4100 and M7100 Managed Switches no set igmp querier query-interval Use this command to set the IGMP Querier Query Interval time to its default value. Format no set igmp querier query-interval Mode set igmp querier timer expiry Use this command to set the IGMP Querier timer expiration period. It is the time period tha[...]

Switching Commands 160 ProSafe M4100 and M7100 Managed Switches than the Snooping Querier ’s address, it stops sending periodic queries. If the Snooping Querier wins the election, then it will continue sending periodic queries. Default Format set igmp querier election participate Mode no set igmp querier election participate Use this command to s[...]

Switching Commands 161 ProSafe M4100 and M7100 Managed Switches When you specify a value for < vlanid >, the following additional information appears. VLAN Admin Mode VLAN Operational State VLAN Operational Max Response Time Querier Election Participation Querier VLAN Address Operational Version Last Querier Address Last Querier Version When [...]

Switching Commands 162 ProSafe M4100 and M7100 Managed Switches interface. MLD Snooping functionality is re-enabled if you disable routing or remove port channel (LAG) membership from an interface that has MLD Snooping enabled. MLD Snooping supports the following activities: • V alidation of address version, payload length consistencies and disca[...]

Switching Commands 163 ProSafe M4100 and M7100 Managed Switches set mld fast -leave Use this command to enable MLD Snooping fast-leave admin mode on a selected interface or VLAN. Enabling fast-leave allows the switch to immediately remove the Layer 2 LAN interface from its forwarding table entry upon receiving and MLD done message for that multicas[...]

Switching Commands 164 ProSafe M4100 and M7100 Managed Switches no set groupmembership-interval Use this command to set the MLDv2 Group Membership Interval time to the default value. Format no set mld groupmembership-interval Mode • Interface Config • Global Config • VLAN Mode set mld maxresponse Use this command to set the MLD Maximum Respon[...]

Switching Commands 165 ProSafe M4100 and M7100 Managed Switches interfaces with multicast routers attached. The range is 0–3600 seconds. A value of 0 indicates an infinite timeout, that is, no expiration. Default Format set mld mcrtexpiretime vlanid 0-3600 Mode • Global Config • Interface Config no set mld mcrtexpiretime Use this command to s[...]

Switching Commands 166 ProSafe M4100 and M7100 Managed Switches no set mld mrouter interface Use this command to disable the status of the interface as a statically configured multicast router-attached interface. Format no set mld mrouter interface Mode show mldsnooping Use this command to display MLD Snooping information. Configured information is[...]

Switching Commands 167 ProSafe M4100 and M7100 Managed Switches When you specify a value for vlanid , the following information appears. VLAN Admin Mode show mldsnooping mrouter interface Use this command to display information about statically configured multicast router attached interfaces. Format show mldsnooping mrouter interface slot/port Mode[...]

VLAN ID MAC Address Type Description Interfaces Switching Commands 168 ProSafe M4100 and M7100 Managed Switches MLD Snooping Querier Commands In an IPv6 environment, MLD Snooping requires that one central switch or router periodically query all end-devices on the network to announce their multicast memberships. This central device is the MLD Querie[...]

Switching Commands 169 ProSafe M4100 and M7100 Managed Switches no set mld querier Use this command to disable MLD Snooping Querier on the system. Use the optional parameter address to reset the querier address. no set mld querier [ vlan-id ][ address ] • Global Config • VLAN Mode set mld querier query_interval Use this command to set the MLD Q[...]

Switching Commands 170 ProSafe M4100 and M7100 Managed Switches set mld querier election participate Use this command to enable the Snooping Querier to participate in the Querier Election process when it discovers the presence of another Querier in the VLAN. When this mode is enabled, if the Snooping Querier finds that the other Querier ’s source[...]

Switching Commands 171 ProSafe M4100 and M7100 Managed Switches When you specify a value for vlanid , the following information appears. When the optional argument detail is used, the command shows the global information and the information for all Querier-enabled VLANs. P ort Security Commands This section describes the commands you use to configu[...]

Switching Commands 172 ProSafe M4100 and M7100 Managed Switches port - security This command enables port locking at the system level (Global Config) or port level (Interface Config) Default Format port-security Mode • Global Config • Interface Config . no port-security This command disables port locking for one (Interface Config) or all (Globa[...]

Switching Commands 173 ProSafe M4100 and M7100 Managed Switches no port-security max-static This command sets maximum number of statically locked MAC addresses to the default value. Format no port-security max-static Mode port - security mac-address This command adds a MAC address to the list of statically locked MAC addresses. The <vid> is t[...]

Switching Commands 174 ProSafe M4100 and M7100 Managed Switches no port-security mac-address sticky The no form removes the sticky mode. The sticky MAC address can be deleted by using the command no port-security mac-address <mac-address> <vid> . Format no port-security mac-address sticky [<mac-address> <vid>] Modes • Glob[...]

Switching Commands 175 ProSafe M4100 and M7100 Managed Switches show port - security static This command displays the statically locked MAC addresses for port. Format show port-security static [lag <lag-intf-num> | <slot/port> ] Mode MAC Address show port - security violation This command displays the source MAC address of the last pack[...]

Switching Commands 176 ProSafe M4100 and M7100 Managed Switches lldp receive Use this command to enable the LLDP receive capability . Default Format lldp receive Mode no lldp receive Use this command to return the reception of LLDPDUs to the default value. Format no lldp receive Mode lldp timers Use this command to set the timing parameters for loc[...]

Switching Commands 177 ProSafe M4100 and M7100 Managed Switches Use port-desc to transmit the port description TL V . T o configure the port description, see description on page 22 Default Format lldp transmit-tlv [sys-desc] [sys-name] [sys-cap] [port-desc] Mode no lldp transmit-tlv Use this command to remove an optional TL V from the LLDPDUs. Use [...]

Switching Commands 178 ProSafe M4100 and M7100 Managed Switches no lldp notification Use this command to disable notifications. Default Format no lldp notification Mode lldp notification-interval Use this command to configure how frequently the system sends remote data change notifications. The <interval> parameter is the number of seconds to[...]

Switching Commands 179 ProSafe M4100 and M7100 Managed Switches show lldp Use this command to display a summary of the current LLDP configuration. Format show lldp Mode Transmit Interval Transmit Hold Multiplier Re-initialization Delay Notification Interval show lldp interface Use this command to display a summary of the current LLDP configuration [...]

Switching Commands 180 ProSafe M4100 and M7100 Managed Switches show lldp statistics Use this command to display the current LLDP traffic and remote table statistics for a specific interface or for all interfaces. Format show lldp statistics {<slot/port> | all} Mode Last Update Total Inserts Total Deletes Total Drops Total Ageouts The table c[...]

Switching Commands 181 ProSafe M4100 and M7100 Managed Switches show lldp remote- device Use this command to display summary information about remote devices that transmit current LLDP data to the system. Y ou can show information about LLDP remote data received on all ports or on a specific port. Format show lldp remote-device {<slot/port> |[...]

Switching Commands 182 ProSafe M4100 and M7100 Managed Switches show lldp remote- device detail Use this command to display detailed information about remote devices that transmit current LLDP data to an interface on the system. Format show lldp remote-device detail <slot/port> Mode Local Interface Remote Identifier Chassis ID Subtype Chassis[...]

Switching Commands 183 ProSafe M4100 and M7100 Managed Switches Port ID: 00:FC:E3:90:01:11 System Name: System Description: Port Description: System Capabilities Supported: System Capabilities Enabled: Time to Live: 24 seconds show lldp local-device Use this command to display summary information about the advertised LLDP local data. This command c[...]

Switching Commands 184 ProSafe M4100 and M7100 Managed Switches LLDP -MED Commands Link Layer Discovery Protocol - Media Endpoint Discovery (LLDP-MED) (ANSI-TIA-1057) provides an extension to the LLDP standard. Specifically , LLDP-MED provides extensions for network configuration and policy , device location, Power over Ethernet (PoE) management an[...]

Switching Commands 185 ProSafe M4100 and M7100 Managed Switches no ldp med confignotification Use this command to disable notifications. Format no lldp med confignotification Mode lldp med transmit -tlv Use this command to specify which optional T ype Length V alues (TL Vs) in the LLDP MED set will be transmitted in the Link Layer Discovery Protoco[...]

Switching Commands 186 ProSafe M4100 and M7100 Managed Switches lldp med all Format lldp med all Mode Use this command to configure LLDP-MED on all the ports no lldp med all Use this command to remove LLDP-MD on all ports. Format no lldp med all Mode lldp med confignotification all U Format lldp med confignotification all Mode se this command to co[...]

Switching Commands 187 ProSafe M4100 and M7100 Managed Switches lldp med transmit -tlv all Use this command to specify which optional T ype Length V alues (TL Vs) in the LLDP MED set will be transmitted in the Link Layer Discovery Protocol Data Units (LLDPDUs). Default Format lldp med transmit-tlv all [capabilities] [ex-pd] [ex-pse] [inventory] [lo[...]

Switching Commands 188 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. (switch) #show lldp med LLDP MED Global Configuration Fast Start Repeat Count: 3 Device Class: Network Connectivity (switch) # show lldp med interface Use this command to display a summary of the current LLDP MED [...]

Switching Commands 189 ProSafe M4100 and M7100 Managed Switches 0/13 Down Disabled Disabled Disabled 0,1 0/14 Down Disabled Disabled Disabled 0,1 TLV Codes: 0- Capabilities, 1- Network Policy 2- Location, 3- Extended PSE 4- Extended Pd, 5- Inventory --More-- or (q)uit (Switch) #show lldp med interface 0/2 Interface Link configMED operMED ConfigNoti[...]

Switching Commands 190 ProSafe M4100 and M7100 Managed Switches (Switch) #show lldp med local-device detail 0/8 LLDP MED Local Device Detail Interface: 0/8 Network Policies Media Policy Application Type : voice Vlan ID: 10 Priority: 5 DSCP: 1 Unknown: False Tagged: True Media Policy Application Type : streamingvideo Vlan ID: 20 Priority: 1 DSCP: 2 [...]

Switching Commands 191 ProSafe M4100 and M7100 Managed Switches show lldp med remote- device This command displays summary information about remote devices that transmit current LLDP MED data to the system. Y ou can show information about LLDP remote data received on all ports or on a specific port. Format show lldp med remote-device {<slot/port[...]

Switching Commands 192 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. (Switch) #show lldp med remote-device detail 0/8 Device Class Shows the device class as advertized by the device remotely connected to the port. Network Policy Information Shows if network policy TL V is received [...]

Switching Commands 193 ProSafe M4100 and M7100 Managed Switches LLDP MED Remote Device Detail Local Interface: 0/8 Remote Identifier: 18 Capabilities MED Capabilities Supported: capabilities, networkpolicy, location, extendedpse MED Capabilities Enabled: capabilities, networkpolicy Device Class: Endpoint Class I Network Policies Media Policy Applic[...]

Switching Commands 194 ProSafe M4100 and M7100 Managed Switches This section describes the commands you use to configure Denial of Service (DoS) Control. The software provides support for classifying and blocking specific types of Denial of Service attacks. Y ou can configure your system to monitor and block these types of attacks: • SIP=DIP: Sou[...]

Switching Commands 195 ProSafe M4100 and M7100 Managed Switches dos -control sipdip This command enables Source IP address = Destination IP address (SIP=DIP) Denial of Service protection. If the mode is enabled, Denial of Service prevention is active for this type of attack. If packets ingress with SIP=DIP , the packets will be dropped if the mode [...]

Switching Commands 196 ProSafe M4100 and M7100 Managed Switches dos- control tcpfrag This command enables TCP Fragment Denial of Service protection. If the mode is enabled, Denial of Service prevention is active for this type of attack. If packets ingress having IP Fragment Offset equal to one (1), the packets will be dropped if the mode is enabled[...]

Switching Commands 197 ProSafe M4100 and M7100 Managed Switches Note: Some applications mirror source and destination L4 ports - RIP for example uses 520 for both. If you enable dos-control l4port, applications such as RIP may experience packet loss which would render the application inoperable. no dos-control l4port This command disables L4 Port D[...]

Switching Commands 198 ProSafe M4100 and M7100 Managed Switches this type of attack. If packets ingress with SMAC=DMAC, the packets will be dropped if the mode is enabled. Default Format dos-control smacdmac Mode no dos-control smacdmac This command disables Source MAC address = Destination MAC address (SMAC=DMAC) Denial of Service protection. Form[...]

Switching Commands 199 ProSafe M4100 and M7100 Managed Switches no dos-control udpport This command disables UDP L4 source = destination port number (Source UDP Port = Destination UDP Port) Denial of Service protection. Format no dos-control udppport Mode dos -control tcpflagseq This command enables TCP Flag and Sequence Denial of Service protectio[...]

Switching Commands 200 ProSafe M4100 and M7100 Managed Switches dos- control tcpsyn This command enables TCP SYN and L4 source = 0-1023 Denial of Service protection. If the mode is enabled, Denial of Service prevention is active for this type of attack. If packets ingress having TCP flag SYN set and an L4 source port from 0 to 1023, the packets wil[...]

Switching Commands 201 ProSafe M4100 and M7100 Managed Switches no dos-control tcpfinurgpsh This command sets disables TCP FIN and URG and PSH and SEQ=0 checking Denial of Service protections. Format no dos-control tcpfinurgpsh Mode dos -control icmpv4 This command enables Maximum ICMPv4 Packet Size Denial of Service protections. If the mode is ena[...]

Switching Commands 202 ProSafe M4100 and M7100 Managed Switches no dos-control icmpv6 This command disables Maximum ICMP Packet Size Denial of Service protections. Format no dos-control icmpv6 Mode dos- control icmpfrag This command enables ICMP Fragment Denial of Service protection. If the mode is enabled, Denial of Service prevention is active fo[...]

Switching Commands 203 ProSafe M4100 and M7100 Managed Switches MA C Database Commands This section describes the commands you use to configure and view information about the MAC databases. bridge aging -time This command configures the forwarding database address aging timeout in seconds. The <seconds> parameter must be within the range of 1[...]

Switching Commands 204 ProSafe M4100 and M7100 Managed Switches no bridge aging-time This command sets the forwarding database address aging timeout to the default value. Format no bridge aging-time Mode show forwardingdb agetime This command displays the timeout for address aging. Default Format show forwardingdb agetime Mode Address Aging Timeout[...]

Switching Commands 205 ProSafe M4100 and M7100 Managed Switches show mac-address-table stats This command displays the Multicast Forwarding Database (MFDB) statistics. Format show mac-address-table stats Mode Max MFDB Table Entries Most MFDB Entries Since Last Reset Current Entries ISDP Commands This section describes the commands you use to config[...]

Switching Commands 206 ProSafe M4100 and M7100 Managed Switches isdp timer This command sets the period of time between sending new ISDP packets. The range is given in seconds. Default Format isdp timer <5-254> Mode isdp advertise-v2 This command enables the sending of ISDP version 2 packets from the device. Default Format isdp advertise-v2 M[...]

Switching Commands 207 ProSafe M4100 and M7100 Managed Switches clear isdp counters This command clears ISDP counters. Format clear isdp counters Mode clear isdp table This command clears entries in the ISDP table. Format clear isdp table Mode show isdp This command displays global ISDP settings. Format show isdp Mode Timer Hold Time Version 2 Adve[...]

Switching Commands 208 ProSafe M4100 and M7100 Managed Switches show isdp interface This command displays ISDP settings for the specified interface. Format show isdp interface {all | <slot/port>} Mode Mode show isdp entry This command displays ISDP entries. If the device id is specified, then only entries for that device are shown. Format sho[...]

Switching Commands 209 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. (Switch) #show isdp neighbors detail Device ID 0001f45f1bc0 Address(es): IP Address: 10.27.7.57 Capability Router Trans Bridge Switch IGMP Platform SecureStack C2 Interface 0/48 Port ID ge.3.14 Holdtime 131 Advert[...]

Switching Commands 210 ProSafe M4100 and M7100 Managed Switches debug isdp packet This command enables tracing of ISDP packets processed by the switch. ISDP must be enabled on both the device and the interface in order to monitor packets for a particular interface. Format debug isdp packet [{receive | transmit}] Mode no debug isdp packet This comma[...]

Switching Commands 21 1 ProSafe M4100 and M7100 Managed Switches dropped frames, while allowing traffic that has greater loss tolerance to continue to flow on the interface. Priorities are differentiated by the priority field of the IEEE 802.1Q VLAN header , which identifies an IEEE 802.1p priority value. In NETGEAR Managed Switch, these priority v[...]

Switching Commands 212 ProSafe M4100 and M7100 Managed Switches VLAN tagging must be enabled to carry the 802.1p value through the network. The number of lossless priorities supported is 2. Additionally , the mapping of class-of-service levels to 802.1p priority values to must be set to one-to-one. Format priority-flow-control priority priority-lis[...]

213 3 3. Multi cas t VL AN R egistr ati on (MVR) This chapter contains the following sections: • About MVR • MVR Commands[...]

Multicast VLAN Registration (MVR) 214 ProSafe M4100 and M7100 Managed Switches About MVR Internet Group Management Protocol (IGMP) Layer 3 is widely used for IPv4 network multicasting. In Layer 2 networks, IGMP uses resources inefficiently . For example, a Layer 2 switch multicasts traffic to all ports, even if there are receivers connected to only[...]

Multicast VLAN Registration (MVR) 215 ProSafe M4100 and M7100 Managed Switches no mvr group This command removes the MVR membership group. mvr mode This command changes the MVR mode type. If the mode is set to compatible, the switch does not learn multicast groups; they need to be configured by the operator as the protocol does not forward joins fr[...]

Multicast VLAN Registration (MVR) 216 ProSafe M4100 and M7100 Managed Switches mvr vlan This command sets the MVR multicast VLAN. no mvr vlan This command sets the MVR multicast VLAN to the default value. mvr immediate This command enables MVR immediate leave mode. MVR has two modes of operating with the IGMP Leave messages: normal leave and immedi[...]

Multicast VLAN Registration (MVR) 217 ProSafe M4100 and M7100 Managed Switches mvr type This command sets the MVR port type. When a port is set as source, it is the port to which the multicast traffic flows using the multicast VLAN. When a port is set to receiver , it is the port where a listening host is connected to the switch. no mvr type Use th[...]

Multicast VLAN Registration (MVR) 218 ProSafe M4100 and M7100 Managed Switches The following table explains the output parameters. Example: (Switch)#show mvr MVR Running…........................... TRUE MVR multicast VLAN….................... 1200 MVR Max Multicast Groups….............. 256 MVR Current multicast groups….......... 1 MVR Glob[...]

Multicast VLAN Registration (MVR) 219 ProSafe M4100 and M7100 Managed Switches (switch)#show mvr members 224.1.1.1 MVR Group IP Status Members ------------------ --------------- --------------------- 224.1.1.1 INACTIVE 0/1, 0/2, 0/3 show mvr interface This command displays the MVR-enabled interfaces configuration. The following table explains the o[...]

Multicast VLAN Registration (MVR) 220 ProSafe M4100 and M7100 Managed Switches show mvr traffic This command displays global MVR statistics. The following table explains the output parameters. Example: (switch)#show mvr traffic IGMP Query Received…........................................ 2 IGMP Report V1 Received…...............................[...]

221 4 4. R o utin g Co mmands This chapter describes the routing commands available in the 7000 series CLI. Note: Some commands described in this chapter require a license. For more information, see Licensing and Command Support on page 8. This chapter contains the following sections: • Address Resolution Protocol (ARP) Commands • IP Routing Co[...]

Routing Commands 222 ProSafe M4100 and M7100 Managed Switches Address R esolution P rotocol (ARP) Commands This section describes the commands you use to configure ARP and to view ARP information about the switch. ARP associates IP addresses with MAC addresses and stores the information as ARP entries in the ARP cache. arp This command creates an A[...]

Routing Commands 223 ProSafe M4100 and M7100 Managed Switches ip proxy -arp This command enables proxy ARP on a router interface. Without proxy ARP , a device only responds to an ARP request if the target IP address is an address configured on the interface where the ARP request arrived. With proxy ARP , the device might also respond if the target [...]

Routing Commands 224 ProSafe M4100 and M7100 Managed Switches no arp dynamicrenew This command prevents dynamic ARP entries from renewing when they age out. Format no arp dynamicrenew Mode arp purge This command causes the specified IP address to be removed from the ARP cache. Only entries of type dynamic or gateway are affected by this command. Fo[...]

Routing Commands 225 ProSafe M4100 and M7100 Managed Switches no arp retries This command configures the default ARP count of maximum request for retries. Format no arp retries Mode arp timeout This command configures the ARP entry ageout time. The value for <seconds> is a valid positive integer , which represents the IP ARP entry ageout time[...]

Routing Commands 226 ProSafe M4100 and M7100 Managed Switches show arp This command displays the Address Resolution Protocol (ARP) cache. The displayed results are not the total ARP entries. T o view the total ARP entries, the operator should view the show arp results with the show arp switch results. Format show arp Mode Age Time (seconds) Respons[...]

Age Time (seconds) Response Time (seconds) Retries Cache Size Dynamic Renew Mode Total Entry Count Current / Peak Static Entry Count Current / Max Routing Commands 227 ProSafe M4100 and M7100 Managed Switches show arp switch This command displays the contents of the switch’s Address Resolution Protocol (ARP) table. Format show arp switch Mode IP [...]

Routing Commands 228 ProSafe M4100 and M7100 Managed Switches no routing This command disables routing for an interface. Y ou can view the current value for this function with the show ip brief command. The value is labeled as “Routing Mode.” Format no routing Mode ip routing This command enables the IP Router Admin Mode for the master switch. [...]

Routing Commands 229 ProSafe M4100 and M7100 Managed Switches no ip address This command deletes an IP address from an interface. The value for <ipaddr> is the IP address of the interface in a.b.c.d format where the range for a, b, c, and d is 1-255. The value for <subnetmask> is a 4-digit dotted-decimal number which represents the Subn[...]

Routing Commands 230 ProSafe M4100 and M7100 Managed Switches no ip default-gateway Use this command to remove the default gateway address from the configuration. Format no ip default-gateway < ipaddr > Mode release dhcp Use this command to force the DHCPv4 client to release the leased address from the specified interface. Format release dhcp[...]

Routing Commands 231 ProSafe M4100 and M7100 Managed Switches ip route This command configures a static route. The <ipaddr> parameter is a valid IP address, and <subnetmask> is a valid subnet mask. The <nexthopip> parameter is a valid IP address of the next hop router . Specifying Null0 as nexthop parameter adds a static reject ro[...]

Routing Commands 232 ProSafe M4100 and M7100 Managed Switches ip route default This command configures the default route. The value for <nexthopip> is a valid IP address of the next hop router . The <preference> is an integer value from 1 to 255. A route with a preference of 255 cannot be used to forward traffic. Default Format ip route[...]

Routing Commands 233 ProSafe M4100 and M7100 Managed Switches ip netdirbcast This command enables the forwarding of network-directed broadcasts. When enabled, network directed broadcasts are forwarded. When disabled they are dropped. Default Format ip netdirbcast Mode no ip netdirbcast This command disables the forwarding of network-directed broadc[...]

Routing Commands 234 ProSafe M4100 and M7100 Managed Switches no ip mtu This command resets the ip mtu to the default value. Format no ip mtu <mtu> Mode encapsulation This command configures the link layer encapsulation type for the packet. The encapsulation type can be ethernet or snap . Default Format encapsulation {ethernet | snap} Mode No[...]

Routing Commands 235 ProSafe M4100 and M7100 Managed Switches show ip brief This command displays all the summary information of the IP , including the ICMP rate limit configuration and the global ICMP Redirect configuration. The following shows example CLI display output for the command. (Switch) #show ip brief Default Time to Live................[...]

Routing Interface Status Primary IP Address Secondary IP Address Method Routing Mode Administrative Mode Forward Net Directed Broadcasts Proxy ARP Local Proxy ARP Active State Link Speed Data Rate MAC Address Encapsulation Type IP MTU Bandwidth Destination Unreachables ICMP Redirects Routing Commands 236 ProSafe M4100 and M7100 Managed Switches The[...]

Routing Commands 237 ProSafe M4100 and M7100 Managed Switches Link Speed Data Rate........................... Inactive MAC address.................................... 02:14:6C:FF:00:DE Encapsulation Type............................. Ethernet IP MTU......................................... 1500 Bandwidth...................................... 100000 [...]

Routing Commands 238 ProSafe M4100 and M7100 Managed Switches Maximum Paths The maximum number of next hops in an OSPF route Routing for Networks The address ranges configured with an OSPF network command Distance The administrative distance (or route preference) for intra-area, inter-area, and external routes Default Route Advertise Whether OSPF i[...]

Routing Commands 239 ProSafe M4100 and M7100 Managed Switches show ip route This command displays the routing table. The <ip-address> specifies the network for which the route is to be displayed and displays the best matching best-route for the address. The <mask> specifies the subnet mask for the given <ip-address> . When you use[...]

Routing Commands 240 ProSafe M4100 and M7100 Managed Switches T o administratively control the traffic destined to a particular network and prevent it from being forwarded through the router , you can configure a static reject route on the router . Such traffic would be discarded and the ICMP destination unreachable message is sent back to the sour[...]

Routing Commands 241 ProSafe M4100 and M7100 Managed Switches ECMP Group 1 with 2 next hops (used by 1 route) 172.20.33.100 on interface 2/33 172.20.34.100 on interface 2/34 ECMP Group 2 with 3 next hops (used by 1 route) 172.20.32.100 on interface 2/32 172.20.33.100 on interface 2/33 172.20.34.100 on interface 2/34 ECMP Group 3 with 4 next hops (u[...]

Routing Commands 242 ProSafe M4100 and M7100 Managed Switches The following shows example CLI display output for the command. (router) #show ip route summary Connected Routes............................... 7 Static Routes.................................. 1 RIP Routes..................................... 20 OSPF Routes..............................[...]

Routing Commands 243 ProSafe M4100 and M7100 Managed Switches Total routes................................... 1032 Best Routes (High)............................. 1032 (1032) Alternate Routes............................... 0 Route Adds..................................... 1010 Route Modifies................................. 1 Route Deletes.........[...]

Routing Commands 244 ProSafe M4100 and M7100 Managed Switches show ip stats This command displays IP statistical information. Refer to RFC 1213 for more information about the fields that are displayed. Format show ip stats Modes • Privileged EXEC • User EXEC show routing heap summary This command displays a summary of the memory allocation from[...]

Routing Commands 245 ProSafe M4100 and M7100 Managed Switches ip irdp This command enables Router Discovery on an interface. Default Format ip irdp Mode no ip irdp This command disables Router Discovery on an interface. Format no ip irdp Mode ip irdp multicast This command configures the address that the interface uses to send the router discovery [...]

Routing Commands 246 ProSafe M4100 and M7100 Managed Switches no ip irdp holdtime This command configures the default value, in seconds, of the holdtime field of the router advertisement sent from this interface. Format no ip irdp holdtime Mode ip irdp maxadvertinterval This command configures the maximum time, in seconds, allowed between sending r[...]

Routing Commands 247 ProSafe M4100 and M7100 Managed Switches ip irdp preference This command configures the preferability of the address as a default router address, relative to other router addresses on the same subnet. Default Format ip irdp preference <-2147483648 to 2147483647> Mode no ip irdp preference This command configures the defau[...]

Routing Commands 248 ProSafe M4100 and M7100 Managed Switches Virtual LAN R outing Commands This section describes the commands you use to view and configure VLAN routing and to view VLAN routing status information. vlan routing This command enables routing on a VLAN. The vlanid value has a range from 1 to 4093. The [interface ID] value has a range[...]

Routing Commands 249 ProSafe M4100 and M7100 Managed Switches Virtual R outer R edundancy Protocol Commands This section describes the commands you use to view and configure Virtual Router Redundancy Protocol (VRRP) and to view VRRP status information. VRRP helps provide failover and load balancing when you configure two devices as a VRRP pair . ip[...]

Routing Commands 250 ProSafe M4100 and M7100 Managed Switches ip vrrp mode This command enables the virtual router configured on the specified interface. Enabling the status field starts a virtual router . The parameter <vrid> is the virtual router ID which has an integer value ranging from 1 to 255. Default Format ip vrrp <vrid> mode M[...]

Routing Commands 251 ProSafe M4100 and M7100 Managed Switches required when authorization type is simple text apssword. The parameter <vrid> is the virtual router IFD which has an integer value range from 1 to 255. Default Format ip vrrp <vrid> authentication {none | simple <key>} Mode no ip vrrp authentication This command sets t[...]

Routing Commands 252 ProSafe M4100 and M7100 Managed Switches another router in the group higher than the master ’s priority , the router will take over as master only if preempt mode is enabled. Default Format ip vrrp <vrid> priority <1-254> Mode no ip vrrp priority This command sets the default priority value for the virtual router [...]

Routing Commands 253 ProSafe M4100 and M7100 Managed Switches decrement) for each downed interface. The default priority decrement is changed using the < priority > argument. The default priority of the virtual router is 100, and the default decrement priority is 10. By default, no interface are tracked. If you specify just the interface to b[...]

Routing Commands 254 ProSafe M4100 and M7100 Managed Switches ip vrrp <vrid> accept -mode This command is used to allow a router to respond to ICMP Echo Requests sent to an address on a VRRP virtual router . VRRP supports responding to pings, but does not allow the VRRP Master to accept other types of packets. A new configuration option contr[...]

Uptime Protocol State Transitioned to Master Advertisement Received Advertisement Interval Errors Authentication Failure IP TTL errors Zero Priority Packets Received Zero Priority Packets Sent Invalid Type Packets Received Address List Errors Invalid Authentication Type Authentication Type Mismatch Packet Length Errors Routing Commands 255 ProSafe [...]

Admin Mode Router Checksum Errors Router Version Errors Router VRID Errors Routing Commands 256 ProSafe M4100 and M7100 Managed Switches show ip vrrp interface This command displays all configuration information and VRRP router statistics of a virtual router configured on a specific interface. Use the output of the command to verify the track inter[...]

Routing Commands 257 ProSafe M4100 and M7100 Managed Switches Advertisement Interval (secs).................. 1 Pre-empt Mode.................................. Enable Administrative Mode............................ Disable Accept Mode.................................... Enable State.......................................... Initialized Track Interf[...]

Routing Commands 258 ProSafe M4100 and M7100 Managed Switches no bootpdhcprelay cidoptmode This command disables the circuit ID option mode for BootP/DHCP Relay on the system. Format no bootpdhcprelay cidoptmode Mode bootpdhcprelay maxhopcount This command configures the maximum allowable relay agent hops for BootP/DHCP Relay on the system. The <[...]

Routing Commands 259 ProSafe M4100 and M7100 Managed Switches show bootpdhcprelay This command displays the BootP/DHCP Relay information. Format show bootpdhcprelay Modes • Privileged EXEC • User EXEC IP Helper Commands This section describes the commands to configure a DHCP relay agent with multiple DHCP server addresses per routing interface,[...]

Routing Commands 260 ProSafe M4100 and M7100 Managed Switches The ip helper-address command forwards specific UDP broadcast from one interface to another . Y ou can define many helper addresses but the total number of address-port pairs is limited to 128 for the whole device. The setting of a helper address for a specific interface has precedence o[...]

Routing Commands 261 ProSafe M4100 and M7100 Managed Switches ip helper -address Use this command to add a unicast helper address to the list of helper addresses on an interface. This is the address of a DHCP server . This command can be applied multiple times on the routing interface to form the helper addresses list until the list reaches the max[...]

Routing Commands 262 ProSafe M4100 and M7100 Managed Switches The following shows example CLI display output for the command. (switch) #show ip helper-address 0/1 Helper IP Address.............................. 1.2.3.4 ............................................... 1.2.3.5 show ip helper statistics Use this command to display the number of DHCP an[...]

Routing Commands 263 ProSafe M4100 and M7100 Managed Switches Open Shortest P ath First (OSPF) Commands This section describes the commands you use to view and configure OSPF , which is a link-state routing protocol that you use to route traffic within a network. router ospf Use this command to enter Router OSPF mode. Format router ospf Mode enable[...]

Routing Commands 264 ProSafe M4100 and M7100 Managed Switches no network area (OSPF) Use this command to disable the OSPFv2 on an interface if the IP address of an interface was earlier covered by this network command. Format no network <ip-address> <wildcard-mask> area <area-id> Mode ip ospf area Use this command to enable OSPFv2[...]

Routing Commands 265 ProSafe M4100 and M7100 Managed Switches no 1583compatibility This command disables OSPF 1583 compatibility . Format no 1583compatibility Mode area default - cost (OSPF) This command configures the default cost for the stub area. Y ou must specify the area ID and an integer value between 1-16,777,215. Format area <areaid>[...]

Routing Commands 266 ProSafe M4100 and M7100 Managed Switches no area nssa default-info-originate (OSPF) This command disables the default route advertised into the NSSA. Format no area <areaid> nssa default-info-originate [<metric>] [{comparable | non-comparable}] Mode area nssa no-redistribute (OSPF) This command configures the NSSA A[...]

Routing Commands 267 ProSafe M4100 and M7100 Managed Switches of candidate causes the router to participate in the translator election process when it attains a border router status. Format area <areaid> nssa translator-role {always | candidate} Mode no area nssa translator (OSPF) This command disables the nssa translator role from the specif[...]

Routing Commands 268 ProSafe M4100 and M7100 Managed Switches no area range The no form of this command deletes a specified area range or reverts an option to its default. Format no area ar eaid range prefix netmask {summarylink | nssaexternallink} [advertise | not-advertise] [cost] Mode area stub (OSPF) This command creates a stub area for the spe[...]

Routing Commands 269 ProSafe M4100 and M7100 Managed Switches no area stub This command deletes a stub area for the specified area ID. Format no area <areaid> stub Mode area stub no- summary (OSPF) This command configures the Summary LSA mode for the stub area identified by <areaid> . Use this command to prevent LSA Summaries from being[...]

Routing Commands 270 ProSafe M4100 and M7100 Managed Switches composed of standard displayable, non-control keystrokes from a Standard 101/102-key keyboard. The authentication key must be 8 bytes or less if the authentication type is simple. If the type is encrypt, the key might be up to 16 bytes. Unauthenticated interfaces do not need an authentic[...]

Routing Commands 271 ProSafe M4100 and M7100 Managed Switches area virtual-link hello-interval (OSPF) This command configures the hello interval for the OSPF virtual interface on the virtual interface identified by <areaid> and <neighbor> . The <neighbor> parameter is the Router ID of the neighbor . The range for <seconds> i[...]

Routing Commands 272 ProSafe M4100 and M7100 Managed Switches area virtual-link transmit - delay (OSPF) This command configures the transmit delay for the OSPF virtual interface on the virtual interface identified by < areaid > and < neighbor > . The < neighbor > parameter is the Router ID of the neighbor . The range for seconds i[...]

Routing Commands 273 ProSafe M4100 and M7100 Managed Switches bandwidth By default, OSPF computes the link cost of an interface as the ratio of the reference bandwidth to the interface bandwidth. Reference bandwidth is specified with the auto-cost command. For the OSPF link cost calculation, use the bandwidth command to specify the interface bandwi[...]

Routing Commands 274 ProSafe M4100 and M7100 Managed Switches clear ip ospf configuration Use this command to reset the OSPF configuration to factory defaults. Format clear ip ospf configuration Mode clear ip ospf counters Use this command to reset global and interface statistics. Format clear ip ospf counters Mode clear ip ospf neighbor Use this c[...]

Routing Commands 275 ProSafe M4100 and M7100 Managed Switches default -information originate (OSPF) This command is used to control the advertisement of default routes. Default • metric—unspecified • type—2 Format default-information originate [always] [metric <0-16777214>] [metric-type {1 | 2}] Mode no default-information originate ([...]

Routing Commands 276 ProSafe M4100 and M7100 Managed Switches no distance ospf This command sets the default route preference value of OSPF routes in the router . The type of OSPF can be intra, inter , or external. All the external type routes are given the same preference value. Format no distance ospf {intra-area | inter-area | external} Mode dis[...]

Routing Commands 277 ProSafe M4100 and M7100 Managed Switches external-lsdb-limit (OSPF) This command configures the external LSDB limit for OSPF . If the value is -1, there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches the external LSDB limit, the router enters overflow state. The route[...]

Routing Commands 278 ProSafe M4100 and M7100 Managed Switches authentication key must be 8 bytes or less if the authentication type is simple. If the type is encrypt, the key might be up to 16 bytes. If the type is encrypt a < keyid > in the range of 0 and 255 must be specified. Unauthenticated interfaces do not need an authentication key or [...]

Routing Commands 279 ProSafe M4100 and M7100 Managed Switches no ip ospf database-filter all out Use this command in Interface Configuration mode to enable OSPFv2 LSA flooding on an interface. Default Format no ip ospf database-filter all out Mode ip ospf dead-interval This command sets the OSPF dead interval for the specified interface. The value [...]

Routing Commands 280 ProSafe M4100 and M7100 Managed Switches no ip ospf hello-interval This command sets the default OSPF hello interval for the specified interface. Format no ip ospf hello-interval Mode ip ospf network Use this command to configure OSPF to treat an interface as a point-to-point rather than broadcast interface. The broadcast optio[...]

Routing Commands 281 ProSafe M4100 and M7100 Managed Switches no ip ospf priority This command sets the default OSPF priority for the specified router interface. Format no ip ospf priority Mode ip ospf retransmit -interval This command sets the OSPF retransmit Interval for the specified interface. The retransmit interval is specified in seconds. Th[...]

Routing Commands 282 ProSafe M4100 and M7100 Managed Switches ip ospf mtu-ignore This command disables OSPF maximum transmission unit (MTU) mismatch detection. OSPF Database Description packets specify the size of the largest IP packet that can be sent without fragmentation on the interface. When a router receives a Database Description packet, it [...]

Routing Commands 283 ProSafe M4100 and M7100 Managed Switches no redistribute This command configures OSPF protocol to prohibit redistribution of routes from the specified source protocol/routers. Format no redistribute {rip | static | connected} [metric] [metric-type] [tag] [subnets] Mode maximum-paths (OSPF) This command sets the number of paths [...]

Routing Commands 284 ProSafe M4100 and M7100 Managed Switches passive-interface (OSPF) Use this command to set the interface or tunnel as passive. It overrides the global passive mode that is effective on the interface or tunnel. Default Format passive-interface {< slot/port >} Mode no passive-interface Use this command to set the interface o[...]

Routing Commands 285 ProSafe M4100 and M7100 Managed Switches timers pacing lsa-group T o adjust how OSPF groups LSAs for periodic refresh, use this command in OSPFv2 Router Configuration mode. OSPF refreshes self-originated LSAs once every 30 minutes. When OSPF refreshes LSAs, it considers all self-originated LSAs whose age is from 1800 to 1800 pl[...]

Routing Commands 286 ProSafe M4100 and M7100 Managed Switches trapflags (OSPF) Use this command to enable individual OSPF traps, enable a group of trap flags at a time, or enable all the trap flags at a time. The dif ferent groups of trapflags, and each group’ s specific trapflags to enable or disable, are listed in T able 1 . T able 1. T rapflag[...]

Routing Commands 287 ProSafe M4100 and M7100 Managed Switches no trapflags Use this command to revert to the default reference bandwidth. • T o disable the individual flag, enter the group name followed by that particular flag. • T o disable all the flags in that group, give the group name followed by all . • T o disable all the flags, give t[...]

Routing Commands 288 ProSafe M4100 and M7100 Managed Switches show ip ospf This command displays information relevant to the OSPF router . Format show ip ospf Mode Note: Some of the information below displays only if you enable OSPF and configure certain features. Privileged EXEC T erm Definition Router ID A 32-bit integer in dotted decimal format [...]

Routing Commands 289 ProSafe M4100 and M7100 Managed Switches ASBR Status Reflects whether the ASBR mode is enabled or disabled. Enable implies that the router is an autonomous system border router . The router automatically becomes an ASBR when it is configured to redistribute routes learnt from other protocols. The possible values for the ASBR st[...]

Routing Commands 290 ProSafe M4100 and M7100 Managed Switches The following shows example CLI display output for the command. (Switch) #show ip ospf Router ID.....................................2.2.2.2 OSPF Admin Mode...............................Disable RFC 1583 Compatibility........................Enable External LSDB Limit.....................[...]

Routing Commands 291 ProSafe M4100 and M7100 Managed Switches Number of Active Areas......................... 3 (3 normal, 0 stub, 0 nssa) ABR Status....................................Disable ASBR Status...................................Disable Stub Router...................................FALSE External LSDB Overflow........................FALSE[...]

AreaID External Routing Spf Runs Area Border Router Count Area LSA Count Area LSA Checksum Import Summary LSAs OSPF Stub Metric Value Routing Commands 292 ProSafe M4100 and M7100 Managed Switches The following OSPF NSSA-specific information displays only if the area is configured as an NSSA: Import Summary LSAs Redistribute into NSSA Default Inform[...]

Routing Commands 293 ProSafe M4100 and M7100 Managed Switches show ip ospf asbr This command displays the internal OSPF routing table entries to Autonomous System Boundary Routers (ASBR). This command takes no options. Format show ip ospf asbr Mode • Privileged EXEC • User EXEC Type Router ID Cost Area ID Next Hop Next Hop Intf show ip ospf dat[...]

Routing Commands 294 ProSafe M4100 and M7100 Managed Switches The information below is only displayed if OSPF is enabled. Format show ip ospf [<areaid>] database [{database-summary | [{asbr-summary | external | network | nssa-external | opaque-area | opaque-as | opaque-link | router | summary}] [{adv-router [<ipaddr>] | self-originate}][...]

Routing Commands 295 ProSafe M4100 and M7100 Managed Switches show ip ospf interface This command displays the information for the IFO object or virtual interface tables. Format show ip ospf interface {<slot/port> | loopback <loopback-id> | vlan <1-4093>} Mode • Privileged EXEC • User EXEC Type-7 Ext T otal number of T ype-7 e[...]

Routing Commands 296 ProSafe M4100 and M7100 Managed Switches The information below will only be displayed if OSPF is enabled. OSPF Interface Type State Designated Router Backup Designated Router Number of Link Events Local Link LSAs Local Link LSA Checksum show ip ospf interface brief This command displays brief information for the IFO object or v[...]

Routing Commands 297 ProSafe M4100 and M7100 Managed Switches show ip ospf interface stats This command displays the statistics for a specific interface. The information below will only be displayed if OSPF is enabled. Format show ip ospf interface stats <slot/port> Modes • Privileged EXEC • User EXEC Retransmit Interval A number represen[...]

Routing Commands 298 ProSafe M4100 and M7100 Managed Switches The command lists the number of OSPF packets of each type sent and received on the interface. Source Not On Local Subnet The number of received packets discarded because the source IP address is not within a subnet configured on a local interface. Note: This field only applies to OSPFv2.[...]

Routing Commands 299 ProSafe M4100 and M7100 Managed Switches show ip ospf neighbor This command displays information about OSPF neighbors. If you do not specify a neighbor IP address, the output displays summary information in a table. If you specify an interface or tunnel, only the information for that interface or tunnel displays. The <ip-add[...]

Routing Commands 300 ProSafe M4100 and M7100 Managed Switches If you specify an IP address for the neighbor router , the following fields display: Interface Neighbor IP Address Interface Index Area ID Options Router Priority Dead Timer Due Up Time State Events Retransmission Queue Length The following shows example CLI display output for the comman[...]

Routing Commands 301 ProSafe M4100 and M7100 Managed Switches show ip ospf range This command displays information about the area ranges for the specified < areaid > . The < areaid > identifies the OSPF area whose ranges are being displayed. Format show ip ospf range < areaid > Modes • Privileged EXEC • User EXEC Area ID IP Ad[...]

Routing Commands 302 ProSafe M4100 and M7100 Managed Switches show ip ospf stub table This command displays the OSPF stub table. The information below will only be displayed if OSPF is initialized on the switch. Format show ip ospf stub table Modes • Privileged EXEC • User EXEC Area ID Type of Service Metric Val Import Summary LSA show ip ospf [...]

Routing Commands 303 ProSafe M4100 and M7100 Managed Switches The following shows example CLI display output for the command. (netgear switch) #show ip ospf traffic Time Since Counters Cleared: 4000 seconds OSPFv2 Packet Statistics Hello Database Desc LS Request LS Update LS ACK Total Recd: 500 10 20 50 20 600 Sent: 400 8 16 40 16 480 LSAs Retransm[...]

Routing Commands 304 ProSafe M4100 and M7100 Managed Switches show ip ospf virtual-link brief This command displays the OSPF Virtual Interface information for all areas in the system. Format show ip ospf virtual-link brief Modes • Privileged EXEC • User EXEC Area ID Neighbor Hello Interval Dead Interval Retransmit Interval Transit Delay OSPF Gr[...]

Routing Commands 305 ProSafe M4100 and M7100 Managed Switches avoiding announcement of a topology change and the potential for flooding of LSAs and shortest-path-first (SPF) runs, which determine OSPF routes. Helpful neighbors continue to forward packets through the restarting router . The restarting router relearns the network topology from its he[...]

Routing Commands 306 ProSafe M4100 and M7100 Managed Switches set long enough to allow the restarting router to reestablish all of its adjacencies and complete a full database exchange with each of those neighbors. no nsfrestart -interval Use this command to revert the grace period to its default value. nsf helper Use this command to enable helpful[...]

Routing Commands 307 ProSafe M4100 and M7100 Managed Switches nsf helper disable Use this command to disable helpful neighbor functionality for OSPF . Note: The commands no nsf helper and nsf ietf helper disable are functionally equivalent. The command nsf ietf helper disable is supported solely for compatibility with other network software CLI. ns[...]

Routing Commands 308 ProSafe M4100 and M7100 Managed Switches max -metric router -lsa T o configure OSPF to enter stub router mode, use this command in Router OSPF Global Configuration mode. When OSPF is in stub router mode, as defined by RFC 3137, OSPF sets the metric in the nonstub links in its router LSA to LsInfinity . Other routers therefore c[...]

Routing Commands 309 ProSafe M4100 and M7100 Managed Switches the command no max-metric router-lsa on-startup . The command no max-metric router-lsa summary-lsa causes OSPF to send summary LSAs with metrics computed using normal procedures defined in RFC 2328. Format no max-metric router-lsa [on-startup] [summary-lsa] Mode OSPF Interface Flap Dampe[...]

Routing Commands 310 ProSafe M4100 and M7100 Managed Switches show dampening interface This command summarizes the number of interfaces configured with dampening and the number of interfaces being suppressed. Format show dampening interface Mode The following shows example CLI display output for the command. (netgear switch)# show dampening interfa[...]

Routing Commands 31 1 ProSafe M4100 and M7100 Managed Switches Any change in the dampening configuration resets the current penalty , reuse time, and suppressed state to their default values, meaning 0, 0, and F ALSE respectively . The following shows example CLI display output for the command. (netgear switch)# show interface dampening Interface 0[...]

Routing Commands 312 ProSafe M4100 and M7100 Managed Switches ip rip This command enables RIP on a router interface. Default Format ip rip Mode no ip rip This command disables RIP on a router interface. Format no ip rip Mode auto- summary This command enables the RIP auto-summarization mode. Default Format auto-summary Mode no auto-summary This com[...]

Routing Commands 313 ProSafe M4100 and M7100 Managed Switches default -metric (RIP) This command is used to set a default for the metric of distributed routes. Format default-metric < 0-15 > Mode no default-metric (RIP) This command is used to reset the default metric of distributed routes to its default value. Format no default-metric Mode d[...]

Routing Commands 314 ProSafe M4100 and M7100 Managed Switches no distribute-list out This command is used to specify the access list to filter routes received from the source protocol. Format no distribute-list <1-199> out {ospf | static | connected} Mode ip rip authentication This command sets the RIP V ersion 2 Authentication T ype and Key [...]

Routing Commands 315 ProSafe M4100 and M7100 Managed Switches no ip rip receive version This command configures the interface to allow RIP control packets of the default version(s) to be received. Format no ip rip receive version Mode ip rip send version This command configures the interface to allow RIP control packets of the specified version to [...]

Routing Commands 316 ProSafe M4100 and M7100 Managed Switches split -horizon This command sets the RIP split horizon mode. Split horizon is a technique for avoiding problems caused by including routes in updates sent to the router from which the route was originally learned. The options are: None - no special processing for this case. Simple - a ro[...]

Routing Commands 317 ProSafe M4100 and M7100 Managed Switches show ip rip This command displays information relevant to the RIP router . Format show ip rip Modes • Privileged EXEC • User EXEC RIP Admin Mode Split Horizon Mode Auto Summary Mode Host Routes Accept Mode Global Route Changes Global queries Default Metric Default Route Advertise sho[...]

Routing Commands 318 ProSafe M4100 and M7100 Managed Switches show ip rip interface This command displays information related to a particular RIP interface. Format show ip rip interface { <slot/port> | vlan <1-4093>} Modes • Privileged EXEC • User EXEC Interface IP Address Send Version Receive Version RIP Admin Mode Link State Authe[...]

Routing Commands 319 ProSafe M4100 and M7100 Managed Switches ip unreachables Use this command to enable the generation of ICMP Destination Unreachable messages. By default, the generation of ICMP Destination Unreachable messages is enabled. Default Format ip unreachables Mode no ip unreachables Use this command to prevent the generation of ICMP De[...]

Routing Commands 320 ProSafe M4100 and M7100 Managed Switches no ip icmp echo-reply Use this command to prevent the generation of ICMP Echo Reply messages by the router . Format no ip icmp echo-reply Mode ip icmp error -interval Use this command to limit the rate at which IPv4 ICMP error messages are sent. The rate limit is configured as a token bu[...]

321 5 5. IP Multi cas t Co mmands This chapter describes the IP Multicast commands available in the managed switch CLI. Note: Some commands described in this chapter require a license. For more information, see Licensing and Command Support on page 8. This chapter contains the following sections: • Multicast Commands • DVMRP Commands • PIM Co[...]

IP Multicast Commands 322 ProSafe M4100 and M7100 Managed Switches no ip mcast boundary This command deletes an administrative scope multicast boundary specified by < groupipaddr > and < mask > for which this multicast administrative boundary is applicable. < groupipaddr > is a group IP address and < mask > is a group IP mas[...]

IP Multicast Commands 323 ProSafe M4100 and M7100 Managed Switches no ip multicast ttl-threshold This command applies the default < ttlthreshold> to a routing interface. The < ttlthreshold> is the TTL threshold which is to be applied to the multicast Data packets which are to be forwarded from the interface . Format no ip multicast ttl-[...]

IP Multicast Commands 324 ProSafe M4100 and M7100 Managed Switches show ip mcast boundary This command displays all the configured administrative scoped multicast boundaries. Format show ip mcast boundary {<slot/port> | all} Modes • Privileged EXEC • User EXEC Interface Group Ip Mask show ip mcast interface This command displays the multi[...]

IP Multicast Commands 325 ProSafe M4100 and M7100 Managed Switches If you use the detail parameter , the command displays the following fields: Source IP Group IP Expiry Time Up Time RPF Neighbor Flags If you use the summary parameter , the command displays the following fields: Source IP Group IP Protocol Incoming Interface Outgoing Interface List[...]

IP Multicast Commands 326 ProSafe M4100 and M7100 Managed Switches show ip mcast mroute source This command displays the multicast configuration settings such as flags, timer settings, incoming and outgoing interfaces, RPF neighboring routers, and expiration times of all the entries in the multicast mroute table containing the given source IP addre[...]

IP Multicast Commands 327 ProSafe M4100 and M7100 Managed Switches ip dvmrp(Global Config) This command sets administrative mode of DVMRP in the router to active. Default Format ip dvmrp Mode no ip dvmrp(Global Config) This command sets administrative mode of DVMRP in the router to inactive. Format no ip dvmrp Mode ip dvmrp metric This command conf[...]

IP Multicast Commands 328 ProSafe M4100 and M7100 Managed Switches no ip dvmrp trapflags This command disables the DVMRP trap mode. Format no ip dvmrp trapflags Mode ip dvmrp This command sets the administrative mode of DVMRP on an interface to active. Default Format ip dvmrp Mode no ip dvmrp This command sets the administrative mode of DVMRP on an[...]

IP Multicast Commands 329 ProSafe M4100 and M7100 Managed Switches show ip dvmrp interface This command displays the interface information for DVMRP on the specified interface. Format show ip dvmrp interface < slot/port > Modes • Privileged EXEC • User EXEC Interface Mode Metric Local Address The following field is displayed only when DVM[...]

IfIndex Nbr IP Addr State Up Time Expiry Time Generation ID Major Version Minor Version Capabilities Received Routes Rcvd Bad Pkts Rcvd Bad Routes IP Multicast Commands 330 ProSafe M4100 and M7100 Managed Switches show ip dvmrp nexthop This command displays the next hop information on outgoing interfaces for routing multicast datagrams. Format show[...]

IP Multicast Commands 331 ProSafe M4100 and M7100 Managed Switches show ip dvmrp prune This command displays the table listing the router ’s upstream prune information. Format show ip dvmrp prune Modes • Privileged EXEC • User EXEC Group IP Source IP Source Mask Expiry Time (secs) show ip dvmrp route This command displays the multicast routin[...]

IP Multicast Commands 332 ProSafe M4100 and M7100 Managed Switches routing across the Internet, independent of the mechanisms provided by any particular unicast routing protocol. ip pim dense (Global Config) This command enables the administrative mode of PIM-DM in the router . Default Format ip pim dense Mode no ip pim dense (Global Config) This c[...]

IP Multicast Commands 333 ProSafe M4100 and M7100 Managed Switches no ip pim hello-interval This command resets the transmission frequency of hello messages between PIM enabled neighbors to its default value. Format no ip pim hello-interval Mode show ip pim interface This command displays the PIM Interface status parameters. If the interface number[...]

IP Multicast Commands 334 ProSafe M4100 and M7100 Managed Switches Join Prune Interval (secs) 60 DR Priority NA BSR Border Disabled Neighbor Count 1 Designated Router NA show ip pim neighbor This command displays the neighbor information for PIM on the specified interface. Format show ip pim neighbor <slot/port> Modes Neighbor Address Interfa[...]

IP Multicast Commands 335 ProSafe M4100 and M7100 Managed Switches no ip pim sparse(Global Config) This command is used to administratively disable PIM-SM multicast routing mode on the router . Format no ip pim sparse Mode ip pim bsr -border Use this command to prevent bootstrap router (BSR) messages from being sent or received through an interface[...]

IP Multicast Commands 336 ProSafe M4100 and M7100 Managed Switches no ip pim bsr-candidate This command is used to disable the router to announce its candidacy as a bootstrap router (BSR). Format no ip pim bsr-candidate interface [vlan | <slot/port>] Mode ip pim dr -priority Use this command to set the priority value for which a router is ele[...]

IP Multicast Commands 337 ProSafe M4100 and M7100 Managed Switches < groupaddress > is the group address supported by the RP . The parameter < groupmask > is the group mask for the group address. The optional keyword override indicates that if there is a conflict, the RP configured with this command prevails over the RP learned by BSR. [...]

IP Multicast Commands 338 ProSafe M4100 and M7100 Managed Switches ip pim ssm Use this command to define the Source Specific Multicast (SSM) range of IP multicast addresses. Default Format ip pim ssm {default | <group-address> <group-mask>} Mode default-range no ip pim ssm This command is used to disable the Source Specific Multicast (S[...]

PIM Mode Interface Interface-Mode Operational-Sta tus IP Multicast Commands 339 ProSafe M4100 and M7100 Managed Switches Example 1: (Switch) #show ip pim PIM Mode Dense Interface Interface-Mode Operational-Status --------- -------------- ------------------ 0/1 Enabled Operational 0/3 Disabled Non-Operational Example 2: (Switch) #show ip pim PIM Mod[...]

IP Multicast Commands 340 ProSafe M4100 and M7100 Managed Switches show ip pim bsr -router This command displays the bootstrap router (BSR) information. The output includes elected BSR information and information about the locally configured candidate rendezvous point (RP) advertisement. Format show ip pim bsr-router [candidate | elected] Mode • [...]

IP Multicast Commands 341 ProSafe M4100 and M7100 Managed Switches show ip pim rp mapping This command displays the mappings for the PIM group to the active rendezvous points.. Format show ip pim rp mapping [<rp address> | candidate | static] Modes RP Address Group Address Group Mask Origin Expiry Time Example 1: (Switch) #show ip pim rp mapp[...]

IP Multicast Commands 342 ProSafe M4100 and M7100 Managed Switches Group Mask 255.255.0.0 Origin Static Expiry Time (hh:mm:ss) NA Internet Group Message P rotocol (IGMP) Commands This section describes the commands you use to view and configure IGMP settings. ip igmp This command sets the administrative mode of IGMP in the system to active. Default[...]

IP Multicast Commands 343 ProSafe M4100 and M7100 Managed Switches ip igmp last -member - query-count This command sets the number of Group-Specific Queries sent before the router assumes that there are no local members on the interface. The range for < count> is 1–20. Format ip igmp last-member-query-count <count> Modes no ip igmp la[...]

IP Multicast Commands 344 ProSafe M4100 and M7100 Managed Switches no ip igmp query-interval This command resets the query interval for the specified interface to the default value. This is the frequency at which IGMP Host-Query packets are transmitted on this interface. Format no ip igmp query-interval Modes ip igmp query -max -response-time This [...]

IP Multicast Commands 345 ProSafe M4100 and M7100 Managed Switches ip igmp startup- query-count This command sets the number of Queries sent out on startup, separated by the Startup Query Interval on the interface. The range for < count> is 1–20. Default Format ip igmp startup-query-count < count > Mode no ip igmp startup-query-count [...]

IGMP Admin Mode Interface Interface-Mode Operational-Sta tus IP Multicast Commands 346 ProSafe M4100 and M7100 Managed Switches show ip igmp groups This command displays the registered multicast groups on the interface. If [detail] is specified this command displays the registered multicast groups on the interface in detail. Format show ip igmp gro[...]

IP Multicast Commands 347 ProSafe M4100 and M7100 Managed Switches show ip igmp interface This command displays the IGMP information for the interface. Format show ip igmp interface < slot/port > Modes • Privileged EXEC • User EXEC Interface IGMP Admin Mode Interface Mode IGMP Version Query Interval Query Max Response Time Robustness Star[...]

IP Multicast Commands 348 ProSafe M4100 and M7100 Managed Switches show ip igmp interface membership This command displays the list of interfaces that have registered in the multicast group. Format show ip igmp interface membership <multiipaddr> [detail] Mode Interface Interface IP State Group Compatibility Mode Source Filter Mode If you use [...]

Querier Status Querier IP Address Querier Up Time Querier Expiry Time Wrong Version Queries Number of Joins Number of Groups IP Multicast Commands 349 ProSafe M4100 and M7100 Managed Switches IGMP P roxy Commands The IGMP Proxy is used by IGMP Router (IPv4 system) to enable the system to issue IGMP host messages on behalf of hosts that the system d[...]

IP Multicast Commands 350 ProSafe M4100 and M7100 Managed Switches ip igmp-proxy unsolicit-rprt -interval This command sets the unsolicited report interval for the IGMP Proxy router . This command is valid only when you enable IGMP Proxy on the interface. The value of <interval> can be 1-260 seconds. Default Format ip igmp-proxy unsolicit-rpr[...]

IP Multicast Commands 351 ProSafe M4100 and M7100 Managed Switches Example: The following example shows CLI display output for the command. (Switch) #show ip igmp-proxy Interface Index............................................. 0/1 Admin Mode................................................ Enable Operational Mode..................................[...]

IP Multicast Commands 352 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. (Switch) #show ip igmp-proxy interface Interface Index................................ 0/1 Ver Query Rcvd Report Rcvd Report Sent Leave Rcvd Leave Sent ----------------------------------------------------------[...]

IP Multicast Commands 353 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. (Switch) #show ip igmp-proxy groups Interface Index................................ 0/1 Group Address Last Reporter Up Time Member State Filter Mode Sources ------------- -------------- ---------- -------------[...]

IP Multicast Commands 354 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. (Switch) #show ip igmp-proxy groups Interface Index................................ 0/1 Group Address Last Reporter Up Time Member State Filter Mode Sources ------------- -------------- ----------- ------------[...]

355 6 6. IPv6 Co mmands This chapter describes the IPv6 commands available in the managed switch CLI. Note: Some commands described in this chapter require a license. For more information, see Licensing and Command Support on page 8. This chapter contains the following sections: • T unnel Interface Commands • IPv6 Routing Commands • OSPFv3 Co[...]

IPv6 Commands 356 ProSafe M4100 and M7100 Managed Switches T unnel Interface Commands The commands in this section describe how to create, delete, and manage tunnel interfaces. Several different types of tunnels provide functionality to facilitate the transition of IPv4 networks to IPv6 networks. These tunnels are divided into two classes: configur[...]

IPv6 Commands 357 ProSafe M4100 and M7100 Managed Switches tunnel mode ipv6ip This command specifies the mode of the tunnel. With the optional 6to4 argument, the tunnel mode is set to 6to4 automatic. Without the optional 6to4 argument, the tunnel mode is configured. Format tunnel mode ipv6ip [6to4] Mode show interface tunnel This command displays t[...]

IPv6 Commands 358 ProSafe M4100 and M7100 Managed Switches ipv6 hop-limit This command defines the unicast hop count used in ipv6 packets originated by the node. The value is also included in router advertisements. V alid values for <hops> are 1-255 inclusive. The default “not configured” means that a value of zero is sent in router adver[...]

IPv6 Commands 359 ProSafe M4100 and M7100 Managed Switches no ipv6 enable Use this command to disable IPv6 routing on an interface. Format no ipv6 enable Mode ipv6 address Use this command to configure an IPv6 address on an interface, including tunnel and loopback interfaces, and to enable IPv6 processing on this interface. Y ou can assign multiple[...]

IPv6 Commands 360 ProSafe M4100 and M7100 Managed Switches ipv6 address autoconfig This command is used to enable stateless address autoconfiguration capability . Note: When unicast-routing is enabled, autoconfig mode does not work. Format ipv6 address autoconfig Mode ipv6 address autoconfig This command disables the stateless autoconfiguration. Fo[...]

IPv6 Commands 361 ProSafe M4100 and M7100 Managed Switches using a link-local address as the next hop. A route with a preference of 255 cannot be used to forward traffic. Default Format ipv6 route <ipv6-prefix>/<prefix_length> {<next-hop-address> | Null0 | interface {<slot/port> | tunnel <tunnel_id>} <next-hop-addre[...]

IPv6 Commands 362 ProSafe M4100 and M7100 Managed Switches ipv6 mtu This command sets the maximum transmission unit (MTU) size, in bytes, of IPv6 packets on an interface. This command replaces the default or link MTU with a new MTU value. Note: The default MTU value for a tunnel interface is 1480. Y ou cannot change this value . no ipv6 mtu This co[...]

IPv6 Commands 363 ProSafe M4100 and M7100 Managed Switches ipv6 nd managed-config-flag This command sets the “managed address configuration” flag in router advertisements. When the value is true, end nodes use DHCPv6. When the value is false, end nodes automatically configure addresses. Default Format ipv6 nd managed-config-flag Mode no ipv6 nd[...]

IPv6 Commands 364 ProSafe M4100 and M7100 Managed Switches no ipv6 nd other-config-flag This command resets the “other stateful configuration” flag back to its default value in router advertisements sent from the interface. Format no ipv6 nd other-config-flag Mode ipv6 nd ra-interval This command sets the transmission interval between router ad[...]

IPv6 Commands 365 ProSafe M4100 and M7100 Managed Switches ipv6 nd reachable-time This command sets the router advertisement time to consider a neighbor reachable after neighbor discovery confirmation. Reachable time is specified in milliseconds. A value of zero means the time is unspecified by the router . Default Format ipv6 nd reachable-time <[...]

IPv6 Commands 366 ProSafe M4100 and M7100 Managed Switches ipv6 nd router-preference Format no ipv6 router-preference Mode This command will set the router preference to default. ipv6 unreachables Use this command to enable the generation of ICMPv6 Destination Unreachable messages. By default, the generation of ICMPv6 Destination Unreachable messag[...]

IPv6 Commands 367 ProSafe M4100 and M7100 Managed Switches no ipv6 icmp error-interval Use the no form of the command to return burst-interval and burst-size to their default values. Format no ipv6 icmp error-interval Mode show ipv6 brief Use this command to display the IPv6 status of forwarding mode and IPv6 unicast routing mode. Format show ipv6 [...]

IPv6 Commands 368 ProSafe M4100 and M7100 Managed Switches show ipv6 interface Use this command to show the usability status of IPv6 interfaces and whether ICMPv6 Destination Unreachable messages might be sent. Format show ipv6 interface {brief | <slot/port> |tunnel <0-7> | loopback <0-7>} Mode If you use the brief parameter , the[...]

IPv6 Commands 369 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. (Switch) #show ipv6 interface 0/1 Routing Mode................................... Disabled Administrative Mode............................ Enabled IPv6 Routing Operational Mode.................. Disabled Bandwidth.....[...]

IPv6 Commands 370 ProSafe M4100 and M7100 Managed Switches show ipv6 neighbor Use this command to display information about the IPv6 neighbors. Format show ipv6 neighbor Mode clear ipv6 neighbors Use this command to clear all entries IPv6 neighbor table or an entry on a specific interface. Use the <slot/port> parameter to specify the interfac[...]

IPv6 Commands 371 ProSafe M4100 and M7100 Managed Switches Note: If you use the connected keyword for <protocol> , the all option is not available because there are no best or non-best connected routes. The show ipv6 route command displays the routing tables in the following format: Codes: C - connected, S - static O - OSPF Intra, OI - OSPF I[...]

IPv6 Commands 372 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. (Switch) #show ipv6 route IPv6 Routing Table - 3 entries Codes: C - connected, S - static O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF Ext 1, OE2 - OSPF Ext 2 ON1 - OSPF NSSA Ext Type 1, ON2 - OSPF NSSA Ext Type 2 S 200[...]

IPv6 Commands 373 ProSafe M4100 and M7100 Managed Switches show ipv6 route preferences Use this command to show the preference value associated with the type of route. Lower numbers have a greater preference. A route with a preference of 255 cannot be used to forward traffic. Format show ipv6 route preferences Mode Local Static OSPF Intra OSPF Inte[...]

IPv6 Commands 374 ProSafe M4100 and M7100 Managed Switches The following example shows CLI display output for the command. (switch) #show ipv6 route summary Connected Routes............................... 4 Static Routes.................................. 0 6To4 Routes.................................... 0 Alternate Routes The number of alternate ro[...]

IPv6 Commands 375 ProSafe M4100 and M7100 Managed Switches OSPF Routes.................................... 13 Intra Area Routes............................ 0 Inter Area Routes............................ 13 External Type-1 Routes....................... 0 External Type-2 Routes....................... 0 Reject Routes..................................[...]

IPv6 Commands 376 ProSafe M4100 and M7100 Managed Switches show ipv6 traffic Use this command to show traffic and statistics for IPv6 and ICMPv6. Specify a logical, loopback, or tunnel interface to view information about traffic on a specific interface. If you do not specify an interface, the command displays information about traffic on all interf[...]

IPv6 Commands 377 ProSafe M4100 and M7100 Managed Switches Received Datagrams Discarded Other Number of input IPv6 datagrams for which no problems were encountered to prevent their continue processing, but which were discarded (for example, for lack of buffer space). Note that this counter does not include datagrams discarded while awaiting reassem[...]

IPv6 Commands 378 ProSafe M4100 and M7100 Managed Switches ICMPv6 Messages with errors Number of ICMP messages which the interface received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, and so on). ICMPv6 Destination Unreachable Messages Number of ICMP Destination Unreachable messages received by the interface. ICMP[...]

IPv6 Commands 379 ProSafe M4100 and M7100 Managed Switches clear ipv6 route counters This command resets to zero the IPv6 routing table counters reported in show ipv6 route summary . The command resets only the event counters. Counters that report the current state of the routing table, such as the number of routes of each type, are not reset. Form[...]

IPv6 Commands 380 ProSafe M4100 and M7100 Managed Switches clear ipv6 statistics Use this command to clear IPv6 statistics for all interfaces or for a specific interface, including loopback and tunnel interfaces. IPv6 statistics display in the output of the show ipv6 traffic command. If you do not specify an interface, the counters for all IPv6 tra[...]

IPv6 Commands 381 ProSafe M4100 and M7100 Managed Switches ipv6 ospf cost This command configures the cost on an OSPF interface. The < cost > parameter has a range of 1–65,535. Default Format ipv6 ospf cost < 1-65535> Mode no ipv6 ospf cost This command configures the default cost on an OSPF interface. Format no ipv6 ospf cost Mode ip[...]

IPv6 Commands 382 ProSafe M4100 and M7100 Managed Switches no ipv6 ospf hello-interval This command sets the default OSPF hello interval for the specified interface. Format no ipv6 ospf hello-interval Mode ipv6 ospf mtu-ignore This command disables OSPF maximum transmission unit (MTU) mismatch detection. OSPF Database Description packets specify th[...]

IPv6 Commands 383 ProSafe M4100 and M7100 Managed Switches no ipv6 ospf network This command sets the interface type to the default value. Format no ipv6 ospf network {broadcast | point-to-point} Mode ipv6 ospf priority This command sets the OSPF priority for the specified router interface. The priority of the interface is a priority integer from 0[...]

IPv6 Commands 384 ProSafe M4100 and M7100 Managed Switches ipv6 ospf transmit - delay This command sets the OSPF T ransit Delay for the specified interface. The transmit delay is specified in seconds. In addition, it sets the estimated number of seconds it takes to transmit a link state update packet over this interface. V alid values for <secon[...]

IPv6 Commands 385 ProSafe M4100 and M7100 Managed Switches no area nssa(OSPFv3) This command disables nssa from the specified area id. Format no area <areaid> nssa Mode area nssa default -info -originate (OSPFv3) This command configures the metric value and type for the default route advertised into the NSSA. The optional metric parameter spe[...]

IPv6 Commands 386 ProSafe M4100 and M7100 Managed Switches area nssa no- summary (OSPFv3) This command configures the NSSA so that summary LSAs are not advertised into the NSSA. Format area <areaid> nssa no-summary Mode no area nssa no-summary (OSPFv3) This command disables nssa from the summary LSAs. Format no area <areaid> nssa no-sum[...]

IPv6 Commands 387 ProSafe M4100 and M7100 Managed Switches no area nssa translator-stab-intv (OSPFv3) This command disables the nssa translator ’s <stabilityinterval> from the specified area id. Format no area <areaid> nssa translator-stab-intv <stabilityinterval> Mode area range (OSPFv3) This command creates a specified area ra[...]

IPv6 Commands 388 ProSafe M4100 and M7100 Managed Switches area stub no- summary (OSPFv3) This command disables the import of Summary LSAs for the stub area identified by <areaid> . Default Format area <areaid> stub no-summary Mode no area stub no-summary(OSPFv3) This command sets the Summary LSA import mode to the default for the stub [...]

IPv6 Commands 389 ProSafe M4100 and M7100 Managed Switches no area virtual-link dead-interval(OSPFv3) This command configures the default dead interval for the OSPF virtual interface on the virtual interface identified by <areaid> and <neighbor> . The <neighbor> parameter is the Router ID of the neighbor . Format no area <areai[...]

IPv6 Commands 390 ProSafe M4100 and M7100 Managed Switches no area virtual-link retransmit-interval(OSPFv3) This command configures the default retransmit interval for the OSPF virtual interface on the virtual interface identified by < areaid > and < neighbor > . The < neighbor > parameter is the Router ID of the neighbor . Format[...]

IPv6 Commands 391 ProSafe M4100 and M7100 Managed Switches no auto-cost reference-bandwidth (OSPFv3) Use this command to set the reference bandwidth to the default value. Format no auto-cost reference-bandwidth Mode clear ipv6 ospf Use this command to disable and re-enable OSPF . Format clear ipv6 ospf Mode clear ipv6 ospf configuration Use this co[...]

IPv6 Commands 392 ProSafe M4100 and M7100 Managed Switches clear ipv6 ospf neighbor interface T o drop adjacency with all neighbors on a specific interface, use the optional parameter [ slot/port ]. T o drop adjacency with a specific router ID on a specific interface, use the optional parameter [ neighbor-id ]. Format clear ipv6 ospf neighbor inter[...]

IPv6 Commands 393 ProSafe M4100 and M7100 Managed Switches no default-metric (OSPFv3) This command is used to set a default for the metric of distributed routes. Format no default-metric Mode distance ospf (OSPFv3) This command sets the route preference value of OSPF route types in the router . Lower route preference values are preferred when deter[...]

IPv6 Commands 394 ProSafe M4100 and M7100 Managed Switches exit - overflow-interval (OSPFv3) This command configures the exit overflow interval for OSPF . It describes the number of seconds after entering Overflow state that a router will wait before attempting to leave the overflow state. This allows the router to again originate non-default AS-ex[...]

IPv6 Commands 395 ProSafe M4100 and M7100 Managed Switches maximum-paths (OSPFv3) This command sets the number of paths that OSPF can report for a given destination where maxpaths is platform-dependent. Default Format maximum-paths <maxpaths> Mode no maximum-paths This command resets the number of paths that OSPF can report for a given destin[...]

IPv6 Commands 396 ProSafe M4100 and M7100 Managed Switches no passive-interface(OSPFv3) Use this command to set the interface or tunnel as non-passive. It overrides the global passive mode that is ef fective on the interface or tunnel. Format no passive-interface {< slot/port > | tunnel < tunnel-id >} Mode redistribute (OSPFv3) This com[...]

IPv6 Commands 397 ProSafe M4100 and M7100 Managed Switches trapflags (OSPFv3) Use this command to enable individual OSPF traps, enable a group of trap flags at a time, or enable all the trap flags at a time. The dif ferent groups of trapflags, and each group’ s specific trapflags to enable or disable, are listed in T able 2, T rapflag Groups (OSP[...]

IPv6 Commands 398 ProSafe M4100 and M7100 Managed Switches • T o enable all the flags, give the command as trapflags all . Default Format trapflags { all | errors {all | authentication-failure | bad-packet | config-error | virt- authentication-failure | virt-bad-packet | virt-config-error} | if-rx {all | if-rx-packet} | lsa {all | lsa-maxage | ls[...]

IPv6 Commands 399 ProSafe M4100 and M7100 Managed Switches Note: Some of the information below displays only if you enable OSPF and configure certain features. T erm Definition Router ID A 32-bit integer in dotted decimal format identifying the router , about which information is displayed. This is a configured value. OSPF Admin Mode Shows whether [...]

IPv6 Commands 400 ProSafe M4100 and M7100 Managed Switches Maximum Number of Retransmit Entries The maximum number of LSAs that can be waiting for acknowledgment at any given time. Retransmit Entries High Water Mark The highest number of LSAs that have been waiting for acknowledgment. External LSDB Limit The maximum number of non-default AS-externa[...]

IPv6 Commands 401 ProSafe M4100 and M7100 Managed Switches show ipv6 ospf abr This command displays the internal OSPFv3 routes to reach Area Border Routers (ABR). This command takes no options. Format show ipv6 ospf abr Modes • Privileged EXEC • User EXEC show ipv6 ospf area This command displays information about the area. The < areaid >[...]

IPv6 Commands 402 ProSafe M4100 and M7100 Managed Switches The following OSPF NSSA-specific information displays only if the area is configured as an NSSA. Import Summary LSAs Redistribute into NSSA Default Information Originate Default Metric Default Metric Type Translator Role Translator Stability Interval Translator State show ipv6 ospf asbr Thi[...]

IPv6 Commands 403 ProSafe M4100 and M7100 Managed Switches show ipv6 ospf database This command displays information about the link state database when OSPFv3 is enabled. If you do not enter any parameters, the command displays the LSA headers for all areas. Use the optional <areaid> parameter to display database information about a specific [...]

IPv6 Commands 404 ProSafe M4100 and M7100 Managed Switches show ipv6 ospf database database- summary Use this command to display the number of each type of LSA in the database and the total number of LSAs in the database. Format show ipv6 ospf database database-summary Modes • Privileged EXEC • User EXEC Router Network Inter-area Prefix Inter-a[...]

IPv6 Commands 405 ProSafe M4100 and M7100 Managed Switches The following information only displays if OSPF is initialized on the interface: OSPF Interface Type State Designated Router Backup Designated Router Number of Link Events Metric Cost show ipv6 ospf interface brief This command displays brief information for the IFO object or virtual interf[...]

IPv6 Commands 406 ProSafe M4100 and M7100 Managed Switches show ipv6 ospf interface stats This command displays the statistics for a specific interface. The command only displays information if OSPF is enabled. Format show ipv6 ospf interface stats <slot/port> Modes • Privileged EXEC • User EXEC T erm Definition Interface V alid slot and [...]

IPv6 Commands 407 ProSafe M4100 and M7100 Managed Switches See show ip ospf interface stats on page 297 for a sample output of the number of OSPF packets of each type sent and received on the interface. show ipv6 ospf neighbor This command displays information about OSPF neighbors. If you do not specify a neighbor IP address, the output displays su[...]

IPv6 Commands 408 ProSafe M4100 and M7100 Managed Switches If you do not specify an IP address, a table with the following columns displays for all neighbors or the neighbor associated with the interface that you specify: Router ID Priority Intf ID Interface State • Down- initial state of the neighbor conversation - no recent information has been[...]

IPv6 Commands 409 ProSafe M4100 and M7100 Managed Switches show ipv6 ospf range This command displays information about the area ranges for the specified < areaid > . The < areaid > identifies the OSPF area whose ranges are being displayed. Format show ipv6 ospf range < areaid > Modes • Privileged EXEC • User EXEC show ipv6 os[...]

IPv6 Commands 410 ProSafe M4100 and M7100 Managed Switches show ipv6 ospf virtual-link This command displays the OSPF Virtual Interface information for a specific area and neighbor . The < areaid > parameter identifies the area and the < neighbor > parameter identifies the neighbor ’s Router ID. Format show ipv6 ospf virtual-link <[...]

IPv6 Commands 41 1 ProSafe M4100 and M7100 Managed Switches OSPFv3 Graceful R estart Commands The managed switch implementation of OSPFv3 supports graceful restart as specified in RFC 5187 and RFC 3623. Graceful restart works together with managed switch non-stop forwarding (nsf) to enable the hardware to continue forwarding IPv6 packets using OSPF[...]

IPv6 Commands 412 ProSafe M4100 and M7100 Managed Switches The grace LSA announcing the graceful restart includes the reason for the restart. Reasons 1 (software restart) and 2 (software reload/upgrade) are considered planned restarts. Reasons 0 (unknown) and 3 (switch to redundant control processor) are considered unplanned restarts. Default Forma[...]

IPv6 Commands 413 ProSafe M4100 and M7100 Managed Switches no nsf [ietf] helper strict -lsa- checking (OSPFv3) This command allows OSPF to continue as a helpful neighbor in spite of topology changes. nsf restart -interval (OSPFv3) This command configures the length of the grace period on the restarting router . The grace period must be set long eno[...]

IPv6 Commands 414 ProSafe M4100 and M7100 Managed Switches ipv6 dhcp server Use this command to configure DHCPv6 server functionality on an interface. The <pool-name> is the DHCPv6 pool containing stateless and/or prefix delegation parameters, rapid-commit is an option that allows for an abbreviated exchange between the client and server , an[...]

IPv6 Commands 415 ProSafe M4100 and M7100 Managed Switches These pools are shared between multiple interfaces over which DHCPv6 server capabilities are configured. Format ipv6 dhcp pool <pool-name> Mode no ipv6 dhcp pool This command removes the specified DHCPv6 pool. Format no ipv6 dhcp pool <pool-name> Mode domain-name (IPv6) This com[...]

IPv6 Commands 416 ProSafe M4100 and M7100 Managed Switches prefix - delegation (IPv6) Multiple IPv6 prefixes can be defined within a pool for distributing to specific DHCPv6 Prefix delegation clients. Prefix is the delegated IPv6 prefix. DUID is the client’s unique DUID value (Example: 00:01:00:09:f8:79:4e:00:04:76:73:43:76'). Name is 31 cha[...]

IPv6 Commands 417 ProSafe M4100 and M7100 Managed Switches T erm Definition DHCPv6 Solicit Packets Received Number of solicit received statistics. DHCPv6 Request Packets Received Number of request received statistics. DHCPv6 Confirm Packets Received Number of confirm received statistics. DHCPv6 Renew Packets Received Number of renew received statis[...]

IPv6 Commands 418 ProSafe M4100 and M7100 Managed Switches show ipv6 dhcp interface This command displays DHCPv6 information for all relevant interfaces or the specified interface. If you specify an interface, you can use the optional statistics parameter to view statistics for the specified interface. Format show ipv6 dhcp interface <slot/port&[...]

IPv6 Commands 419 ProSafe M4100 and M7100 Managed Switches show ipv6 dhcp pool This command displays configured DHCP pool. Format show ipv6 dhcp pool <pool-name> Mode DHCP Pool Name Client DUID Host Prefix/Prefix Length Preferred Lifetime Valid Lifetime DNS Server Address Domain Name show ipv6 dhcp binding This command displays configured DHC[...]

IPv6 Commands 420 ProSafe M4100 and M7100 Managed Switches Valid Lifetime V alid lifetime in seconds for delegated prefix. Preferred Lifetime Preferred lifetime in seconds for delegated prefix. T erm Definition[...]

421 7 7. IPv6 Multi cas t Comman ds This chapter describes the IPv6 multicast commands available in the managed switch CLI. Note: Some commands described in this chapter require a license. For more information, see Licensing and Command Support on page 8. This chapter contains the following sections: • IPv6 Multicast Forwarder Commands on page 42[...]

IPv6 Multicast Commands 422 ProSafe M4100 and M7100 Managed Switches IPv6 Multicast Forwarder Commands Note: There is no specific IP multicast enable for IPv6. Enabling of multicast at global config is common for both IPv4 and IPv6. show ipv6 mroute Use this command to show the mroute entries specific for IPv6. (This command is the IPv6 equivalent [...]

IPv6 Multicast Commands 423 ProSafe M4100 and M7100 Managed Switches show ipv6 mroute group This command displays the multicast configuration settings specific to IPv6 such as flags, timer settings, incoming and outgoing interfaces, RPF neighboring routers, and expiration times of all the entries in the multicast mroute table containing the given g[...]

IPv6 Multicast Commands 424 ProSafe M4100 and M7100 Managed Switches If you use the summary parameter , the command displays the following column headings in the output table: Source IP Group IP Protocol Incoming Interface Outgoing Interface List IPv6 PIM Commands This section describes the Protocol Independent Multicast (PIM) commands that support[...]

IPv6 Multicast Commands 425 ProSafe M4100 and M7100 Managed Switches no ipv6 pim (Interface Config) Use this command to set the administrative mode of PIM on an interface to disabled. Format no ipv6 pim Mode ipv6 pim hello-interval Use this command to configure the PIM hello interval for the specified router interface. The hello-interval is specifi[...]

IPv6 Multicast Commands 426 ProSafe M4100 and M7100 Managed Switches PIM Mode..................................... Dense Data Threshold Rate (Kbps)................... 0 Register Rate-limit (Kbps)................... 0 Interface Interface Mode Operational-Status --------- -------------- ---------------- 0/1 Enabled Non-Operational show ipv6 pim neigh[...]

IPv6 Multicast Commands 427 ProSafe M4100 and M7100 Managed Switches (Switch) #show ipv6 pim interface 0/1 Interface...................................... 0/1 Mode........................................... Dense Hello Interval (secs).......................... 30 Join Prune Interval (secs)..................... 60 DR Priority........................[...]

IPv6 Multicast Commands 428 ProSafe M4100 and M7100 Managed Switches no ipv6 pim bsr-candidate Use this command to disable the router to announce its candidacy as a bootstrap router (BSR). Format no ipv6 pim bsr-candidate interface [ <slot/port> | vlan <1-4093>] [hash-mask-length] [priority] Mode ipv6 pim dr -priority Use this command t[...]

IPv6 Multicast Commands 429 ProSafe M4100 and M7100 Managed Switches ipv6 pim join-prune-interval Use this command to configure the interface join/prune interval for the PIM-SM router . The join/prune interval is specified in seconds. This parameter can be configured to a value from 0 to 18000. Default Format ipv6 pim join-prune-interval <0-1800[...]

IPv6 Multicast Commands 430 ProSafe M4100 and M7100 Managed Switches no ipv6 pim rp-candidate Use this command to disable the router to advertise itself as a PIM candidate rendezvous point (RP) to the bootstrap router (BSR). Format no ipv6 pim rp-candidate interface <slot/port> <group-address> <group-mask> Mode ipv6 pim ssm Use th[...]

BSR Address Uptime BSR Priority Hash Mask Length Next Bootstrap Message In Next Candidate RP advertisement in IPv6 Multicast Commands 431 ProSafe M4100 and M7100 Managed Switches show ipv6 pim rp-hash Use this command to display which rendezvous point (RP) is being used for a specified group. Format show ipv6 pim rp-hash < group-address > Mod[...]

IPv6 Multicast Commands 432 ProSafe M4100 and M7100 Managed Switches network. In this situation, the 7000 series has an IGMP/MLD Snooping Querier running on one of the switches and Snooping enabled on all the switches. For more information, see IGMP Snooping Configuration Commands on page 146 and MLD Snooping Commands on page 158. ipv6 mld router U[...]

IPv6 Multicast Commands 433 ProSafe M4100 and M7100 Managed Switches sent on that interface. The range for <query-max-response-time> is 0–65,535 milliseconds. Default Format ipv6 mld query-max-response-time <query-max-response-time> Mode no ipv6 mld query-max-response-time This command resets the MLD query max response time for the in[...]

IPv6 Multicast Commands 434 ProSafe M4100 and M7100 Managed Switches no ipv6 mld last-member-query-count Use this command to reset the <last-member-query-count> parameter of the interface to the default value. Format no ipv6 mld last-member-query-count Mode show ipv6 mld groups Use this command to display information about multicast groups th[...]

IPv6 Multicast Commands 435 ProSafe M4100 and M7100 Managed Switches The following table is displayed to indicate all the sources associated with this group. Source Address Uptime Expiry Time Example: The following shows examples of CLI display output for the commands. (Switch) #show ipv6 mld groups ? <group-address> Enter Group Address Info.[...]

IPv6 Multicast Commands 436 ProSafe M4100 and M7100 Managed Switches The following information is displayed for each of the interfaces or for only the specified interface. Interface MLD Global Mode MLD Operational Mode MLD Version Query Interval Query Max Response Time Robustness Startup Query interval Startup Query Count Last Member Query Interval[...]

IPv6 Multicast Commands 437 ProSafe M4100 and M7100 Managed Switches show ipv6 mld traffic Use this command to display MLD statistical information for the router . Format show ipv6 mld traffic Mode • Privileged EXEC • User EXEC IPv6 MLD -Proxy Commands MLD-Proxy is the IPv6 equivalent of IGMP-Proxy . MLD-Proxy commands allow you to configure th[...]

IPv6 Multicast Commands 438 ProSafe M4100 and M7100 Managed Switches ipv6 mld-proxy Use this command to enable MLD-Proxy on the router . T o enable MLD-Proxy on the router , you must enable multicast forwarding. Also, make sure that there are no other multicast routing protocols enabled n the router . Format ipv6 mld-proxy Mode no ipv6 mld-proxy Us[...]

IPv6 Multicast Commands 439 ProSafe M4100 and M7100 Managed Switches show ipv6 mld-proxy Use this command to display a summary of the host interface status parameters. Format show ipv6 mld-proxy Mode • Privileged EXEC • User EXEC The command displays the following parameters only when you enable MLD-Proxy . Interface Index Admin Mode Operationa[...]

IPv6 Multicast Commands 440 ProSafe M4100 and M7100 Managed Switches show ipv6 mld-proxy interface This command displays a detailed list of the host interface status parameters. It displays the following parameters only when you enable MLD-Proxy . Format show ipv6 mld-proxy interface Modes • Privileged EXEC • User EXEC Interface Index The colum[...]

IPv6 Multicast Commands 441 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. (Switch) #show ipv6 mld-proxy groups Interface Index................................ 0/3 Group Address Last Reporter Up Time Member State Filter Mode Sources ------------- -------------- ---------- ----------[...]

IPv6 Multicast Commands 442 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. (Switch) #show ipv6 igmp-proxy groups Interface Index................................ 0/3 Group Address Last Reporter Up Time Member State Filter Mode Sources ------------- ---------------- ----------- ------[...]

443 8 8. Quality of Se r v ice (QoS) C omman ds This chapter describes the Quality of Service (QoS) commands available in the managed switch CLI. This chapter contains the following sections: • Class of Service (CoS) Commands • Differentiated Services (DiffServ) Commands • DiffServ Class Commands • DiffServ Policy Commands • DiffServ Serv[...]

Quality of Service (QoS) Commands 444 ProSafe M4100 and M7100 Managed Switches Class of Service (CoS) Commands This section describes the commands you use to configure and view Class of Service (CoS) settings for the switch. The commands in this section allow you to control the priority and transmission rate of traffic. Note: Commands you issue in [...]

Quality of Service (QoS) Commands 445 ProSafe M4100 and M7100 Managed Switches no classofservice ip-dscp-mapping This command maps each IP DSCP value to its default internal traf fic class value. Format no classofservice ip-dscp-mapping Modes classofservice trust This command sets the Class of Service trust mode of an interface. Y ou can set the mo[...]

Quality of Service (QoS) Commands 446 ProSafe M4100 and M7100 Managed Switches cos- queue strict This command activates the strict priority scheduler mode for each specified queue. Format cos-queue strict <queue-id-1> [<queue-id-2> … <queue-id-n>] Modes • Global Config • Interface Config no cos-queue strict This command rest[...]

Quality of Service (QoS) Commands 447 ProSafe M4100 and M7100 Managed Switches random-detect exponential weighting-constant Use this command to configure the WRED decay exponent for a CoS queue interface. Format random-detect exponential-weighting-constant 0-15 Modes • Global Config • Interface Config Default no random-detect exponential weight[...]

Quality of Service (QoS) Commands 448 ProSafe M4100 and M7100 Managed Switches no random-detect queue-parms Use this command to set the WRED configuration back to the default. Format no random-detect queue-parms queue-id-1 [queue-id-2 … queue-id-n] Modes • Global Config • Interface Config traffic-shape This command specifies the maximum trans[...]

Quality of Service (QoS) Commands 449 ProSafe M4100 and M7100 Managed Switches show classofservice ip-precedence -mapping This command displays the current IP Precedence mapping to internal traffic classes for a specific interface. The slot/port parameter is optional and is only valid on platforms that support independent per-port Class of Service [...]

Non-IP Traffic Class Untrusted Traffic Class Quality of Service (QoS) Commands 450 ProSafe M4100 and M7100 Managed Switches show interfaces cos- queue This command displays the class-of-service queue configuration for the specified interface. The slot/port parameter is optional and is only valid on platforms that support independent per-port Class [...]

Quality of Service (QoS) Commands 451 ProSafe M4100 and M7100 Managed Switches show interfaces random-detect This command displays the global WRED settings for each CoS queue. If you specify the slot/port, the command displays the WRED settings for each CoS queue on the specified interface. Format show interfaces random-detect [slot/port] Mode Queu[...]

Quality of Service (QoS) Commands 452 ProSafe M4100 and M7100 Managed Switches The following rules apply when you create a DiffServ class: • Each class can contain a maximum of one referenced (nested) class • Class definitions do not support hierarchical service policies A given class definition can contain a maximum of one reference to another[...]

Quality of Service (QoS) Commands 453 ProSafe M4100 and M7100 Managed Switches This set of commands consists of class creation/deletion and matching, with the class match commands specifying Layer 3, Layer 2, and general match criteria. The class match criteria are also known as class rules, with a class definition consisting of one or more rules t[...]

Quality of Service (QoS) Commands 454 ProSafe M4100 and M7100 Managed Switches no class-map This command eliminates an existing DiffServ class. The <class-map-name> is the name of an existing Dif fServ class. (The class name ‘default’ is reserved and is not allowed here.) This command might be issued at any time; if the class is currently[...]

Quality of Service (QoS) Commands 455 ProSafe M4100 and M7100 Managed Switches match class-map This command adds to the specified class definition the set of match conditions defined for another class. The <refclassname> is the name of an existing DiffServ class whose match conditions are being referenced by the specified class definition. De[...]

Quality of Service (QoS) Commands 456 ProSafe M4100 and M7100 Managed Switches match secondary cos This command adds to the specified class definition a match condition for the secondary Class of Service value (the only tag in a single tagged packet or the first or outer 802.1Q tag of a double VLAN tagged packet). The value might be from 0 to 7. De[...]

Quality of Service (QoS) Commands 457 ProSafe M4100 and M7100 Managed Switches match dstip6 This command adds to the specified class definition a match condition based on the destination IPv6 address of a packet. Default Format match dstip6 <destination-ipv6-prefix/prefix-length> Mode match dstl4port This command adds to the specified class d[...]

Quality of Service (QoS) Commands 458 ProSafe M4100 and M7100 Managed Switches match ip precedence This command adds to the specified class definition a match condition based on the value of the IP Precedence field in a packet, which is defined as the high-order three bits of the Service T ype octet in the IP header (the low-order five bits are not[...]

Quality of Service (QoS) Commands 459 ProSafe M4100 and M7100 Managed Switches match protocol This command adds to the specified class definition a match condition based on the value of the IP Protocol field in a packet using a single keyword notation or a numeric value notation. T o specify the match condition using a single keyword notation, the [...]

Quality of Service (QoS) Commands 460 ProSafe M4100 and M7100 Managed Switches parameter specifies an IP address bit mask and must consist of a contiguous set of leading 1 bits. Default Format match srcip <ipaddr> <ipmask> Mode match srcip6 This command adds to the specified class definition a match condition based on the source IP addr[...]

Quality of Service (QoS) Commands 461 ProSafe M4100 and M7100 Managed Switches match secondary -vlan This command adds to the specified class definition a match condition based on the value of the layer 2 secondary VLAN Identifier field (the 802.1Q tag of a double VLAN tagged packet). The VLAN is an integer from 0 to 4095. Default Format match seco[...]

Quality of Service (QoS) Commands 462 ProSafe M4100 and M7100 Managed Switches drop This command specifies that all packets for the associated traffic stream are to be dropped at ingress. Format drop Mode Incompatibilities mirror This command specifies that all incoming packets for the associated traffic stream are copied to a specific egress inter[...]

Quality of Service (QoS) Commands 463 ProSafe M4100 and M7100 Managed Switches class This command creates an instance of a class definition within the specified policy for defining treatment of the traffic class through subsequent policy attribute statements. The <classname> is the name of an existing DiffServ class. Note: This command causes[...]

Quality of Service (QoS) Commands 464 ProSafe M4100 and M7100 Managed Switches mark cos-as - sec- cos This command marks outer VLAN tag priority bits of all packets as the inner VLAN tag priority , marking CoS as Secondary CoS. This essentially means that the inner VLAN tag CoS is copied to the outer VLAN tag CoS. Format mark-cos-as-sec-cos Mode In[...]

Quality of Service (QoS) Commands 465 ProSafe M4100 and M7100 Managed Switches police- simple This command is used to establish the traffic policing style for the specified class. The simple form of the police command uses a single data rate and burst size, resulting in two outcomes: conform and violate. The conforming data rate is specified in kil[...]

Quality of Service (QoS) Commands 466 ProSafe M4100 and M7100 Managed Switches policy -map This command establishes a new DiffServ policy . The <policyname> parameter is a case-sensitive alphanumeric string from 1 to 31 characters uniquely identifying the policy . The type of policy is specific to the inbound traffic direction as indicated by[...]

Quality of Service (QoS) Commands 467 ProSafe M4100 and M7100 Managed Switches service-policy This command attaches a policy to an interface in the inbound direction. The <policyname> parameter is the name of an existing DiffServ policy . This command causes a service to create a reference to the policy . Note: This command ef fectively enabl[...]

Quality of Service (QoS) Commands 468 ProSafe M4100 and M7100 Managed Switches DiffServ Show Commands Use the DiffServ show commands to display configuration and status information for classes, policies, and services. Y ou can display DiffServ information in summary or detailed formats. The status information is only shown when the DiffServ adminis[...]

Quality of Service (QoS) Commands 469 ProSafe M4100 and M7100 Managed Switches show diffserv This command displays the DiffServ General Status Group information, which includes the current administrative mode setting as well as the current and maximum number of rows in each of the main DiffServ private MIB tables. This command takes no options. For[...]

Quality of Service (QoS) Commands 470 ProSafe M4100 and M7100 Managed Switches The following information is repeated for each class associated with this policy (only the policy attributes that are configured are displayed): T erm Definition Assign Queue Directs traffic stream to the specified QoS queue. This allows a traf fic classifier to specify [...]

Quality of Service (QoS) Commands 471 ProSafe M4100 and M7100 Managed Switches If the Policy Name is not specified this command displays a list of all defined DiffServ policies. The following fields are displayed: Policy Name Policy Type Class Members show diffserv service This command displays policy service information for the specified interface[...]

DiffServ Admin Mode Quality of Service (QoS) Commands 472 ProSafe M4100 and M7100 Managed Switches The following information is repeated for interface and direction (only those interfaces configured with an attached policy are shown): Interface Direction OperStatus Policy Name show policy -map interface This command displays policy-oriented statist[...]

Quality of Service (QoS) Commands 473 ProSafe M4100 and M7100 Managed Switches show service-policy This command displays a summary of policy-oriented statistics information for all interfaces in the specified direction. Format show service-policy {in|out} Mode The following information is repeated for each interface and direction (only those interf[...]

Quality of Service (QoS) Commands 474 ProSafe M4100 and M7100 Managed Switches no mac access-list extended This command deletes a MAC ACL identified by <name> from the system. Format no mac access-list extended <name> Mode mac access-list extended rename This command changes the name of a MAC access control list (ACL). The <name> [...]

Quality of Service (QoS) Commands 475 ProSafe M4100 and M7100 Managed Switches ibmsna, ipv4, ipv6, ipx, mplsmcast, mplsucast, netbios, novell, pppoe, rarp. Each of these translates into its equivalent Ethertype value(s). The time-range parameter allows imposing time limitation on the MAC ACL rule as defined by the parameter <time-range-name>.[...]

Quality of Service (QoS) Commands 476 ProSafe M4100 and M7100 Managed Switches mac access-group This command either attaches a specific MAC access control list (ACL) identified by <name> to an interface, or associates it with a VLAN ID, in a given direction. The <name> parameter must be the name of an existing MAC ACL. An optional seque[...]

Quality of Service (QoS) Commands 477 ProSafe M4100 and M7100 Managed Switches no mac access-group This command removes a MAC ACL identified by <name> from the interface in a given direction. Format no mac access-group <name> {{control-plane|in|out} vlan vlan-id {in|out}} Modes • Global Config • Interface Config show mac access-list[...]

Quality of Service (QoS) Commands 478 ProSafe M4100 and M7100 Managed Switches IP Access Control List (A CL) Commands This section describes the commands you use to configure IP ACL settings. IP ACLs ensure that only authorized users have access to specific resources and block any unwarranted attempts to reach network resources. The following rules[...]

Quality of Service (QoS) Commands 479 ProSafe M4100 and M7100 Managed Switches no access-list This command deletes an IP ACL that is identified by the parameter < accesslistnumber> from the system. The range for < accesslistnumber> 1-99 for standard access lists and 100-199 for extended access lists. Format no access-list <accesslist[...]

Quality of Service (QoS) Commands 480 ProSafe M4100 and M7100 Managed Switches If an IP ACL by this name exists, this command enters IPv4-Access_List config mode to allow updating the existing IP ACL. Note: The CLI mode changes to IPv4-Access-List Config mode when you successfully execute this command. no ip access-list This command deletes the IP [...]

Quality of Service (QoS) Commands 481 ProSafe M4100 and M7100 Managed Switches Note: The mirror parameter allows traf fic matching this rule to be copied to the specified <slot/port> , while the redirect parameter allows traffic matching this rule to be forwarded to the specified <slot/port> . The assign-queue and redirect parameters ar[...]

Quality of Service (QoS) Commands 482 ProSafe M4100 and M7100 Managed Switches number indicates higher precedence order . If a sequence number is already in use for this interface and direction, the specified access list replaces the currently attached IP access list using that sequence number . If the sequence number is not specified for this comm[...]

Quality of Service (QoS) Commands 483 ProSafe M4100 and M7100 Managed Switches show ip access-lists This command displays an IP ACL <accesslistnumber> is the number used to identify the IP ACL. Format show ip access-lists <accesslistnumber> Mode Note: Only the access list fields that you configure are displayed. Privileged EXEC T erm De[...]

Quality of Service (QoS) Commands 484 ProSafe M4100 and M7100 Managed Switches show access-lists This command displays IP ACLs, IPv6 ACLs, and MAC access control lists information for a designated interface and direction. Format show access-lists interface <slot/port> [in|out] Mode ACL Type ACL ID Sequence Number IPv6 Access Control List (A C[...]

Quality of Service (QoS) Commands 485 ProSafe M4100 and M7100 Managed Switches no ipv6 access-list This command deletes the IPv6 ACL identified by <name> from the system. Format no ipv6 access-list <name> Mode ipv6 access-list rename This command changes the name of an IPv6 ACL. The <name> parameter is the name of an existing IPv6[...]

Quality of Service (QoS) Commands 486 ProSafe M4100 and M7100 Managed Switches number of user configurable queues available for the hardware platform. The assign-queue parameter is valid only for a permit rule. The mirror parameter allows the traffic matching this rule to be copied to the specified <slot/port> , while the redirect parameter a[...]

Quality of Service (QoS) Commands 487 ProSafe M4100 and M7100 Managed Switches no ipv6 traffic-filter This command removes an IPv6 ACL identified by <name> from the interface(s) in a given direction. Format no ipv6 traffic-filter <name> {{ control-plane | in | out }|vlan < vlan-id > {in|out}} Modes • Global Config • Interface [...]

Quality of Service (QoS) Commands 488 ProSafe M4100 and M7100 Managed Switches Time R ange Commands for Time -Based A CLs T ime-based ACLs allow one or more rules within an ACL to be based on time. Each ACL rule within an ACL, except for the implicit deny all rule, can be configured to be active and operational only during a specific time period. T[...]

Quality of Service (QoS) Commands 489 ProSafe M4100 and M7100 Managed Switches time zone. The [start time date ] parameters indicate the time and date at which the configuration that referenced the time range starts going into effect. The time is expressed in a 24-hour clock, in the form of hours:minutes. For example, 8:00 is 8:00 am and 20:00 is 8[...]

Quality of Service (QoS) Commands 490 ProSafe M4100 and M7100 Managed Switches no periodic Use this command to delete a periodic time entry from a time range. Format no periodic <frequency>{days-of-the-week time } to {[days-of-the-week] time } Mode periodic {start|end} time Use this command to configure the start/end time for the time-range. [...]

Quality of Service (QoS) Commands 491 ProSafe M4100 and M7100 Managed Switches In a V oIP system, various signaling protocols are used to establish the connection between two V oIP devices. The supported signaling protocols are SIP , H.323, and SCCP . OUI-based Auto V oIP The OUI-based Auto V oIP feature prioritizes V oIP packets based on the OUI b[...]

Quality of Service (QoS) Commands 492 ProSafe M4100 and M7100 Managed Switches no auto-voip oui This command is to delete already configured OUI. Format no auto-voip oui <oui-prefix> Mode auto-voip vlan This command is used to configure the global Auto V oIP VLAN id. The VLAN behavior is depend on the configured auto V oIP mode. Format auto-v[...]

Quality of Service (QoS) Commands 493 ProSafe M4100 and M7100 Managed Switches Note: The administrator has to enable tagging on auto-V oIP-enabled ports to remark the voice data when it is egressed. Format auto-voip protocol-based {remark <remark-priority> | traffic-class <tc>} Mode • Global Config • Interface Config Default no auto[...]

Quality of Service (QoS) Commands 494 ProSafe M4100 and M7100 Managed Switches Interface Auto VoIP Operational Status Mode --------- -------------- ------------------ 0/1 Disabled Down 0/2 Disabled Down 0/3 Disabled Down 0/4 Disabled Down Example: The following shows an example of a CLI display output for the command. (Netgear Switch)# show auto-vo[...]

Quality of Service (QoS) Commands 495 ProSafe M4100 and M7100 Managed Switches • Detecting the establishment and termination of iSCSI sessions and connections by snooping packets used in the iSCSI protocol. • Maintaining a database of currently active iSCSI sessions and connections to store data about the participants. This allows the formulati[...]

Quality of Service (QoS) Commands 496 ProSafe M4100 and M7100 Managed Switches also choose to use these {unreserved} ports). When a port is already defined and not bound to an IP , and the User wants to bind it to an IP , the User should first remove it by using the no form of the command and then add it again, this time together with the relevant [...]

Quality of Service (QoS) Commands 497 ProSafe M4100 and M7100 Managed Switches Note: SCSI flows are assigned by default to the highest VPT/DSCP mapped to the highest queue not used for stack management or voice VLAN. The user should also take care of configuring the relevant Class of Service parameters for the queue in order to complete the setting[...]

Quality of Service (QoS) Commands 498 ProSafe M4100 and M7100 Managed Switches • When aging time is increased - Current sessions will be timed out according to the new value. • When aging time is decreased - Any sessions that have been dormant for a time exceeding the new setting will be immediately deleted from the table. All other sessions wi[...]

Quality of Service (QoS) Commands 499 ProSafe M4100 and M7100 Managed Switches show iscsi sessions The show iscsi sessions Privileged EXEC mode command displays the iSCSI sessions. Format show iscsi sessions [detailed] Mode • Privileged EXEC • User EXEC Default detailed Example: The following example displays the iSCSI sessions. Console # show [...]

Quality of Service (QoS) Commands 500 ProSafe M4100 and M7100 Managed Switches Time for aging out: 2 min ISID: 22 Initiator Initiator Target Target IP address TCP port IP address IP port 172.16.1.30 49200 172.16.1.20 30001 172.16.1.30 49201 172.16.1.21 30001[...]

501 9 9. P o w er o v er Ethe rn et (P oE) Co mmands This chapter contains the following sections: • About PoE • PoE Commands About P oE Power over Ethernet describes a technology to pass electrical power safely along with data on existing Ethernet cabling. The PSE or power supply equipment is the device or switch that delivers electrical power[...]

Power over Ethernet (PoE) Commands 502 ProSafe M4100 and M7100 Managed Switches P oE Commands poe Use this command to enable the Power over Ethernet (PoE) functionality on a global basis or per interface. no poe Use this command to disable the Power over Ethernet (PoE) functionality on a global basis or per interface. poe detection Use this command[...]

Power over Ethernet (PoE) Commands 503 ProSafe M4100 and M7100 Managed Switches no poe detection Use this command to set the detection mode to the default on a global basis or per interface. poe high-power Use this command to switch a port from 802.3af mode to high-power mode. This mode is used to power up devices that require more power than the c[...]

Power over Ethernet (PoE) Commands 504 ProSafe M4100 and M7100 Managed Switches • user-defined —Allows you to define the maximum power to the port. This can be a value from 3 through 32 watts. no poe power limit Use this command to set the power limit type to the default. It also sets the maximum power limit to the default if the power limit ty[...]

Power over Ethernet (PoE) Commands 505 ProSafe M4100 and M7100 Managed Switches Dynamic Power Management Available power = 300 watts - 3 watts = 297 watts no poe power management Use this command to set the power management mode to the default. poe priority Use this command to configure the priority on a specific port. This is used for power manage[...]

Power over Ethernet (PoE) Commands 506 ProSafe M4100 and M7100 Managed Switches this command takes effect only once after it is executed and cannot be saved across power cycles. poe timer schedule name Use this command to allow you to attach a timer schedule to a PoE port. Y ou can define a time schedule using the existing time range commands. This[...]

Power over Ethernet (PoE) Commands 507 ProSafe M4100 and M7100 Managed Switches no poe timer schedule name Use this command to detach the schedule from the port. poe usagethreshold Use this command to set a threshold (as a percentage) for the total amount of power that can be delivered by the switch. For example, if the switch can deliver up to a m[...]

Power over Ethernet (PoE) Commands 508 ProSafe M4100 and M7100 Managed Switches no poe traps Use this command to disable logging the PoE traps. show poe Use this command to get global information regarding the PoE status. • ON—Indicates that the PoE controller is actively delivering power . • OFF—Indicates that the PoE controller is not del[...]

Power over Ethernet (PoE) Commands 509 ProSafe M4100 and M7100 Managed Switches Example: (switch) #show poe Firmware Version............................... 1.0.0.2 PSE Main Operational Status.................... ON Total Power (Main AC).......................... 380 Total Power (RPS).............................. 300 Total Power (PD) ..............[...]

Power over Ethernet (PoE) Commands 510 ProSafe M4100 and M7100 Managed Switches show poe port info Use this command to get information about the status of the PoE ports. Y ou can display information based on each individual port or all the ports collectively . The command displays only PSE-capable ports. • Disabled—The PoE function is disabled [...]

Power over Ethernet (PoE) Commands 51 1 ProSafe M4100 and M7100 Managed Switches High Max Output Output Intf Power Power Class Power Current Voltage Status Fault (W) (W) (mA) (volt) Status ------ ------- ----- ------- ------ ------- ------- ------------------ --------------- 0/33 No 18.0 2 04.400 84 53.3 Delivering Power No Error show poe pd Use th[...]

512 10 10. Utility Comman ds This chapter describes the utility commands available in the CLI. This chapter contains the following sections: • Auto Install Commands • Dual Image Commands • System Information and Statistics Commands • Logging Commands • Email Alerting and Mail Server Commands • System Utility and Clear Commands • Simpl[...]

Utility Commands 513 ProSafe M4100 and M7100 Managed Switches Auto Install Commands This section describes the Auto Install Commands. Auto Install is a software feature which provides for the configuration of a switch automatically when the device is initialized and no configuration file is found on the switch. The Auto Install process requires DHC[...]

Utility Commands 514 ProSafe M4100 and M7100 Managed Switches boot host auto- save This command is used to enable automatically saving the downloaded configuration on the switch. Default Format boot host auto-save Mode no boot host auto-save This command is used to disable automatically saving the downloaded configuration on the switch. Format no b[...]

Utility Commands 515 ProSafe M4100 and M7100 Managed Switches no boot host retry-count This command is used to reset the number to the default. The default number is 3. Format no boot host retry-count Mode boot host dhcp This command is used to enable AutoInstall on the switch for the next reboot cycle. The command does not change the current behav[...]

Utility Commands 516 ProSafe M4100 and M7100 Managed Switches delete This command deletes the supplied image file from the permanent storage. The image to be deleted must be a backup image. If this image is the active image, or if this image is activated, an error message displays. The optional <unit> parameter is valid only on Stacks. Error [...]

Utility Commands 517 ProSafe M4100 and M7100 Managed Switches update bootcode This command updates the bootcode (boot loader) on the switch. The bootcode is read from the active-image for subsequent reboots. The optional <unit> parameter is valid only on Stacks. Error will be returned, if this parameter is provided, on Standalone systems. For[...]

Utility Commands 518 ProSafe M4100 and M7100 Managed Switches Note: Event log information is retained across a switch reset. show hardware This command displays inventory information for the switch. Note: The show version command and the show hardware command display the same information. In future releases of the software, the show hardware comman[...]

Utility Commands 519 ProSafe M4100 and M7100 Managed Switches show interface This command displays a summary of statistics for a specific interface or a count of all CPU traffic based upon the argument. Format show interface {<slot/port> | switchport | lag < lag-intf-num >} Mode The display parameters, when the argument is <slot/port[...]

Utility Commands 520 ProSafe M4100 and M7100 Managed Switches The display parameters, when the argument is “switchport” are as follows: Packets Received Without Error Broadcast Packets Received Packets Received With Error Packets Transmitted Without Error Broadcast Packets Transmitted Transmit Packet Errors Address Entries Currently In Use VLAN[...]

Utility Commands 521 ProSafe M4100 and M7100 Managed Switches show interface ethernet This command displays detailed statistics for a specific interface or for all CPU traffic based upon the argument. Format show interface ethernet { slot/port | switchport} Mode When you specify a value for slot/port , the command displays the following information[...]

Utility Commands 522 ProSafe M4100 and M7100 Managed Switches (cont) • Packets RX and TX 65–127 Octets - The total number of packets (including bad packets) received and transmitted that were from 65 through 127 octets in length inclusive (excluding framing bits but including FCS octets). • Packets RX and TX 128–255 Octets - The total numbe[...]

Utility Commands 523 ProSafe M4100 and M7100 Managed Switches Packets Received with MAC Errors • T otal Packets Received with MAC Errors - The total number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. • Jabbers Received - The total number of packets received that were longer than 15[...]

Utility Commands 524 ProSafe M4100 and M7100 Managed Switches Packets T ransmitted Octets • T otal Packets T ransmitted (Octets) - The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets). This object can be used as a reasonable estimate of Ethernet utilization. [...]

Utility Commands 525 ProSafe M4100 and M7100 Managed Switches T ransmit Discards • T otal T ransmit Packets Discards - The sum of single collision frames discarded, multiple collision frames discarded, and excessive frames discarded. • Single Collision Frames - A count of the number of successfully transmitted frames on a particular interface f[...]

Utility Commands 526 ProSafe M4100 and M7100 Managed Switches If you use the switchport keyword, the following information appears. T erm Definition Octets Received The total number of octets of data received by the processor (excluding framing bits but including FCS octets). T otal Packets Received Without Error The total number of packets (includ[...]

Utility Commands 527 ProSafe M4100 and M7100 Managed Switches show mac-addr -table This command displays the forwarding database entries. These entries are used by the transparent bridging function to determine how to forward a received frame. Enter all or no parameter to display the entire table. Enter a MAC Address and VLAN ID to display the tabl[...]

Utility Commands 528 ProSafe M4100 and M7100 Managed Switches If you enter the interface <slot/port> parameter , in addition to the MAC Address and Status fields, the following field appears: VLAN ID The following information displays if you enter the count parameter: Dynamic Address count Static Address (User-defined) count Total MAC Address[...]

Utility Commands 529 ProSafe M4100 and M7100 Managed Switches falling utilization threshold is optional. If the falling CPU utilization parameters are not configured, they take the same value as the rising CPU utilization parameters. Format process cpu threshold type total rising <1-100> interval <5-86400> {falling <1-100> interva[...]

Utility Commands 530 ProSafe M4100 and M7100 Managed Switches bcmCNTR.0 0.20% bcmLINK.0 0.35% DHCP snoop 0.10% Dynamic ARP Inspection 0.10% dot1s_timer_task 0.10% dhcpsPingTask 0.20% show mbuf total This command shows the total system buffer pools status. Format Mode The following shows an example of CLI display output for the command. (switch) #sh[...]

Utility Commands 531 ProSafe M4100 and M7100 Managed Switches Note: If you issue the show running-config command from a serial connection, access to the switch through remote connections (such as T elnet) is suspended while the output is being generated and displayed. Note: If you use a text-based configuration file, the show running-config command[...]

Switch Description System Name System Location System Contact System Object ID System Up Time MIBs Supported Utility Commands 532 ProSafe M4100 and M7100 Managed Switches show tech-support Use this command to display system and configuration information when you contact technical support. The output of this command combines the output of the follow[...]

Utility Commands 533 ProSafe M4100 and M7100 Managed Switches length Use this command to set the pagination length to value number of lines for the sessions specified by configuring on different Line Config modes (telnet, ssh, and console) and is persistent. Default Format length <0|5-48> Mode no length value Use this command to set the pagin[...]

Utility Commands 534 ProSafe M4100 and M7100 Managed Switches memory free low-watermark processor Use this command to get notifications when the CPU free memory falls below the configured threshold. A notification is generated when the free memory falls below the threshold. Another notification is generated once the available free memory rises to 1[...]

Utility Commands 535 ProSafe M4100 and M7100 Managed Switches logging buffered wrap This command enables wrapping of in-memory logging when the log file reaches full capacity . Otherwise when the log file reaches full capacity , logging stops. Default Format logging buffered wrap Mode no logging buffered wrap This command disables wrapping of in-me[...]

Utility Commands 536 ProSafe M4100 and M7100 Managed Switches no logging console This command disables logging to the console. Format no logging console Mode logging host This command enables logging to a host. Y ou can configure up to eight hosts. The <ipaddr|hostname> is the IP address of the logging host. The <addresstype> indicates [...]

Utility Commands 537 ProSafe M4100 and M7100 Managed Switches no logging syslog This command disables syslog logging. Format no logging syslog Mode logging syslog source-interface This command configures the syslog source-interface. Format logging syslog source-interface {<u/s/p> | {loopback < loopback-id >} | {tunnel < tunnel-id >[...]

Utility Commands 538 ProSafe M4100 and M7100 Managed Switches show logging buffered This command displays buffered logging (system startup and system operation logs). Format show logging buffered Mode Buffered (In-Memory) Logging Buffered Logging Wrapping Behavior Buffered Log Count show logging hosts This command displays all configured logging ho[...]

Number of Traps Since Last Reset Trap Log Capacity Number of Traps Since Log Last Viewed Log System Time Up Trap Utility Commands 539 ProSafe M4100 and M7100 Managed Switches logging persistent Use this command to configure the Persistent logging for the switch. The severity level of logging messages is specified at severity level. Possible values [...]

Utility Commands 540 ProSafe M4100 and M7100 Managed Switches no logging email This command disables email alerting. Format no logging email Mode logging email urgent This command sets the lowest severity level at which log messages are emailed immediately in a single email message. Specify the severitylevel value as either an integer from 0 to 7 o[...]

Utility Commands 541 ProSafe M4100 and M7100 Managed Switches no logging email message-type to-addr This command removes the configured to-addr field of email. Format no logging email message-type {urgent |non-urgent |both} to-addr < to-email-addr > Mode logging email from-addr This command configures the email address of the sender (the swit[...]

Utility Commands 542 ProSafe M4100 and M7100 Managed Switches logging email logtime This command configures how frequently non-urgent email messages are sent. Non-urgent messages are collected and sent in a batch email at the specified interval. The valid range is every 30- 1440 minutes. Default Format logging email logtime < minutes > Mode n[...]

Utility Commands 543 ProSafe M4100 and M7100 Managed Switches show logging email config This command displays information about the email alert configuration. Format show logging email config Mode Email Alert Logging Email Alert From Address Email Alert Urgent Severity Level Email Alert Non Urgent Severity Level Email Alert Trap Severity Level Emai[...]

Utility Commands 544 ProSafe M4100 and M7100 Managed Switches clear logging email statistics This command resets the email alerting statistics. Format clear logging email statistics Mode mail-server Use this command to configure the SMTP server to which the switch sends email alert messages and change the mode to Mail Server Configuration mode. The[...]

Utility Commands 545 ProSafe M4100 and M7100 Managed Switches port Use this command to configure the TCP port to use for communication with the SMTP server . The recommended port for TLSv1 is 465, and for no security (i.e. none) it is 25. However , any nonstandard port in the range 1–65,535 is also allowed. Default Format port {465 | 25 | 1–655[...]

Utility Commands 546 ProSafe M4100 and M7100 Managed Switches System Utility and Clear Commands This section describes the commands you use to help troubleshoot connectivity issues and to restore various configurations to their factory defaults. traceroute Use the traceroute command to discover the routes that packets actually take when traveling t[...]

Utility Commands 547 ProSafe M4100 and M7100 Managed Switches The following are examples of the CLI command. traceroute Success: (Switch) # traceroute 10.240.10.115 initTtl 1 maxTtl 4 maxFail 0 interval 1 count 3 port 33434 size 43 Traceroute to 10.240.10.115 ,4 hops max 43 byte packets: 1 10.240.4.1 708 msec 41 msec 11 msec 2 10.240.10.115 0 msec [...]

Utility Commands 548 ProSafe M4100 and M7100 Managed Switches of the traceroute. This port should be an unused port on the destination system. The range for < port > is zero (0) to 65535. The default value is 33434. Default Format traceroute ipv6 < ipv6-address|hostname > [ port < port >] Mode clear config This command resets the [...]

Utility Commands 549 ProSafe M4100 and M7100 Managed Switches clear counters This command clears the statistics for a specified <slot/port>, for all the ports, or for the entire switch based upon the argument. Format clear counters {<slot/port> | all} Mode clear igmpsnooping This command clears the tables managed by the IGMP Snooping fu[...]

Utility Commands 550 ProSafe M4100 and M7100 Managed Switches enable password This command prompts you to change the Privileged EXEC password. Passwords are a maximum of 64 alphanumeric characters. The password is case-sensitive. The option [encrypted] allows the administrator to transfer the enable password between devices without having to know t[...]

Utility Commands 551 ProSafe M4100 and M7100 Managed Switches Using the options described below , you can specify the number and size of Echo Requests and the interval between Echo Requests. count interval size The following are examples of the CLI command. ping success: (Switch) #ping 10.254.2.160 count 3 interval 1 size 255 Pinging 10.254.2.160 w[...]

Utility Commands 552 ProSafe M4100 and M7100 Managed Switches command, configure the switch for network (in-band) connection. The source and target devices must have the ping utility enabled and running on top of TCP/IP . The switch can be pinged from any IP workstation with which the switch is connected through the default VLAN (VLAN 1), as long a[...]

Utility Commands 553 ProSafe M4100 and M7100 Managed Switches quit This command closes the current telnet connection or resets the current serial connection. The system asks you whether to save configuration changes before quitting. Format quit Modes • Privileged EXEC • User EXEC reload This command resets the switch without powering it off. Re[...]

Utility Commands 554 ProSafe M4100 and M7100 Managed Switches In the copy url ias-users command, for url , use one of the following for the IAS user's file: { { tftp://<ipaddr | hostname> | <ipv6address | hostname> /<filepath>/<filename> } | { sftp | scp://<username>@<ipaddress>/<filepath>/<filename[...]

Utility Commands 555 ProSafe M4100 and M7100 Managed Switches nvram:traplog <url> Copies the trap log file to a server . system:running-config nvram:startup-config Saves the running configuration to nvram. <url> nvram:clibanner Downloads the CLI banner to the system. <url> nvram:script <destfilename> Downloads a configuratio[...]

Utility Commands 556 ProSafe M4100 and M7100 Managed Switches write memory Use this command to save running configuration changes to NVRAM so that the changes you make will persist across a reboot. This command is the same as copy system:running config nvram:startup-config . Format write memory Mode Simple Network Time P rotocol (SNTP) Commands Thi[...]

Utility Commands 557 ProSafe M4100 and M7100 Managed Switches sntp client mode This command enables Simple Network T ime Protocol (SNTP) client mode and might set the mode to either broadcast or unicast. Default Format sntp client mode [broadcast | unicast] Mode no sntp client mode This command disables Simple Network T ime Protocol (SNTP) client m[...]

Utility Commands 558 ProSafe M4100 and M7100 Managed Switches no sntp unicast client poll-interval This command resets the poll interval for SNTP unicast clients to its default value. Format no sntp unicast client poll-interval Mode sntp unicast client poll-timeout This command will set the poll timeout for SNTP unicast clients in seconds to a valu[...]

Utility Commands 559 ProSafe M4100 and M7100 Managed Switches sntp server This command configures an SNTP server (a maximum of three). The optional priority can be a value of 1-3, the version a value of 1-4, and the port id a value of 1-65535. Format sntp server <ipaddress|ipv6address| hostname> [<priority> [<version> [<portid&[...]

Utility Commands 560 ProSafe M4100 and M7100 Managed Switches clock set This command sets the system time and date. Format clock set <hh:mm:ss> clock set <mm/dd/yyyy> Mode clock summer -time recurring Use the clock summer-time recurring command to set the summertime offset to UTC recursively every year . If the optional parameters are n[...]

Utility Commands 561 ProSafe M4100 and M7100 Managed Switches • offset—Number of minutes to add during the summertime. (Range:1-1440) • acronym—The acronym for the time zone to be displayed when summertime is in ef fect. (Range: Up to four characters) For example: (Switch)(config)# clock summer-time date 1 Apr 2007 02:00 28 Oct 2007 offset [...]

Utility Commands 562 ProSafe M4100 and M7100 Managed Switches show sntp client This command is used to display SNTP client settings. Format show sntp client Mode Client Supported Modes SNTP Version Port Client Mode show sntp server This command is used to display SNTP server settings and configured servers. Format show sntp server Mode Server Host [...]

Utility Commands 563 ProSafe M4100 and M7100 Managed Switches For each configured server: Host Address Address Type Priority Version Port Last Attempt Time Last Update Status Total Unicast Requests Failed Unicast Requests show clock Use the show clock command in Privileged EXEC or User EXEC mode to display the time and date from the system clock. U[...]

Utility Commands 564 ProSafe M4100 and M7100 Managed Switches DHCP Server Commands This section describes the commands you to configure the DHCP server settings for the switch. DHCP uses UDP as its transport protocol and supports a number of features that facilitate in administration address allocations. ip dhcp pool This command configures a DHCP [...]

Utility Commands 565 ProSafe M4100 and M7100 Managed Switches client -name This command specifies the name for a DHCP client. Name is a string consisting of standard ASCII characters. Default Format client-name <name> Mode no client-name This command removes the client name. Format no client-name Mode default -router This command specifies th[...]

Utility Commands 566 ProSafe M4100 and M7100 Managed Switches no dns-server This command removes the DNS Server list. Format no dns-server Mode hardware-address This command specifies the hardware address of a DHCP client. Hardware-address is the MAC address of the hardware platform of the client consisting of 6 bytes in dotted hexadecimal format. [...]

Utility Commands 567 ProSafe M4100 and M7100 Managed Switches lease This command configures the duration of the lease for an IP address that is assigned from a DHCP server to a DHCP client. The overall lease time should be between 1-86400 minutes. If you specify infinite , the lease is set for 60 days. Y ou can also specify a lease duration. Days i[...]

Utility Commands 568 ProSafe M4100 and M7100 Managed Switches no bootfile This command deletes the boot image name. Format no bootfile Mode domain-name This command specifies the domain name for a DHCP client. The <domain> specifies the domain name string of the client. Default Format domain-name <domain> Mode no domain-name This comman[...]

Utility Commands 569 ProSafe M4100 and M7100 Managed Switches netbios-node -type The command configures the NetBIOS node type for Microsoft Dynamic Host Configuration Protocol (DHCP) clients. type specifies the NetBIOS node type. V alid types are: • b-node—Broadcast • p-node—Peer-to-peer • m-node—Mixed • h-node—Hybrid (recommended) [...]

Utility Commands 570 ProSafe M4100 and M7100 Managed Switches period (for example, a3.4f.22.0c ), colon (for example, a3:4f:22:0c ), or white space (for example, a3 4f 22 0c ). Default Format option <code> {ascii string | hex <string1> [<string2>...<string8>] | ip <address1> [<address2>...<address8>]} Mode [...]

Utility Commands 571 ProSafe M4100 and M7100 Managed Switches no ip dhcp ping packets This command prevents the server from pinging pool addresses and sets the number of packets to 0. Default Format no ip dhcp ping packets Mode service dhcp This command enables the DHCP server . Default Format service dhcp Mode no service dhcp This command disables[...]

Utility Commands 572 ProSafe M4100 and M7100 Managed Switches ip dhcp conflict logging This command enables conflict logging on DHCP server . Default Format ip dhcp conflict logging Mode no ip dhcp conflict logging This command disables conflict logging on DHCP server . Format no ip dhcp conflict logging Mode clear ip dhcp binding This command dele[...]

Utility Commands 573 ProSafe M4100 and M7100 Managed Switches show ip dhcp binding This command displays address bindings for the specific IP address on the DHCP server . If no IP address is specified, the bindings corresponding to all the addresses are displayed. Format show ip dhcp binding [<address>] Modes • Privileged EXEC • User EXEC[...]

Pool Name Pool Type Lease Time DNS Servers Default Routers Utility Commands 574 ProSafe M4100 and M7100 Managed Switches The following additional field is displayed for Dynamic pool type: Network The following additional fields are displayed for Manual pool type: Client Name Client Identifier Hardware Address Hardware Address Type Host show ip dhcp[...]

Utility Commands 575 ProSafe M4100 and M7100 Managed Switches Message Received: DHCP DISCOVER DHCP REQUEST DHCP DECLINE DHCP RELEASE DHCP INFORM Message Sent: DHCP OFFER DHCP ACK DHCP NACK show ip dhcp conflict This command displays address conflicts logged by the DHCP Server . If no IP address is specified, all the conflicting addresses are displa[...]

Utility Commands 576 ProSafe M4100 and M7100 Managed Switches ip domain lookup Use this command to enable the DNS client. Default Format ip domain lookup Mode no ip domain lookup Use this command to disable the DNS client. Format no ip domain lookup Mode ip domain name Use this command to define a default domain name that the software uses to compl[...]

Utility Commands 577 ProSafe M4100 and M7100 Managed Switches name command, is used only when the default domain name list is empty . A maximum of 32 names can be entered in to this list. Default Format ip domain list <name> Mode no ip domain list Use this command to delete a name from a list. Format no ip domain list <name> Mode ip nam[...]

Utility Commands 578 ProSafe M4100 and M7100 Managed Switches no ip host Use this command to remove the name-to-address mapping. Format no ip host < name > Mode ipv6 host Use this command to define static host name-to-IPv6 address mapping in the host cache. < name > is host name. <v6 address > is the IPv6 address of the host. Defa[...]

Utility Commands 579 ProSafe M4100 and M7100 Managed Switches ip domain timeout Use this command to specify the amount of time to wait for a response to a DNS query . The parameter < seconds > specifies the time, in seconds, to wait for a response to a DNS query . < seconds > ranges from 0 to 3600. Default Format ip domain timeout < [...]

Utility Commands 580 ProSafe M4100 and M7100 Managed Switches Example: The following shows example CLI display output for the command. <Switch> show hosts Host name......................... Device Default domain.................... gm.com Default domain list............... yahoo.com, Stanford.edu, rediff.com Domain Name lookup................[...]

Utility Commands 581 ProSafe M4100 and M7100 Managed Switches packets are captured and capturing packets is stopped automatically .The packet capture operates in three modes: • Capture file • Remote capture • Capture line The command is not persistent across a reboot cycle. Format capture {start|stop} {transmit|receive|all} Mode capture {file[...]

Utility Commands 582 ProSafe M4100 and M7100 Managed Switches no capture Use this command to reset the capture mode to remote mode. Format no capture Mode capture remote port Use this command to configure file capture options. The command is persistent across a reboot cycle. Default Format capture remote port <port-id> Mode no capture remote [...]

Utility Commands 583 ProSafe M4100 and M7100 Managed Switches displayed during the capturing session. When capturing is in progress, unsaved, not-yet-displayed packets will not be lost. Default Format capture line wrap Mode no capture line wrap Use this command to disable the capture line wrap mode. Format no capture line wrap Mode show capture pac[...]

Utility Commands 584 ProSafe M4100 and M7100 Managed Switches no debug arp Use this command to disable ARP debug protocol messages. Format no debug arp Mode debug auto-voip Use this command to enable Auto VOIP debug messages. Use the optional parameters to trace H323, SCCP , or SIP packets respectively . Default Format debug auto-voip [H323|SCCP|SI[...]

Utility Commands 585 ProSafe M4100 and M7100 Managed Switches no debug console This command disables the display of “debug” trace output on the login session in which it is executed. Format no debug console Mode debug crashlog Use this command to view information contained in the crash log file that the system maintains when it experiences an u[...]

Utility Commands 586 ProSafe M4100 and M7100 Managed Switches debug dhcp packet Use this command to display “debug” information about DHCPv4 client activities and trace DHCPv4 packets to and from the local DHCPv4 client. Default Format debug dhcp packet [transmit | receive] Mode no debug dhcp Use this command to disable the display of “debug?[...]

Utility Commands 587 ProSafe M4100 and M7100 Managed Switches no debug igmpsnooping packet This command disables tracing of IGMP Snooping packets. Format no debug igmpsnooping packet Mode debug igmpsnooping packet transmit This command enables tracing of IGMP Snooping packets transmitted by the switch. Snooping should be enabled on the device and t[...]

Utility Commands 588 ProSafe M4100 and M7100 Managed Switches no debug igmpsnooping transmit This command disables tracing of transmitted IGMP snooping packets. Format no debug igmpsnooping transmit Mode debug igmpsnooping packet receive This command enables tracing of IGMP Snooping packets received by the switch. Snooping should be enabled on the [...]

Utility Commands 589 ProSafe M4100 and M7100 Managed Switches no debug igmpsnooping receive This command disables tracing of received IGMP Snooping packets. Format no debug igmpsnooping receive Mode debug ip acl Use this command to enable debug of IP Protocol packets matching the ACL criteria. Default Format debug ip acl <acl Number> Mode no [...]

Utility Commands 590 ProSafe M4100 and M7100 Managed Switches no debug ip dvmrp packet Use this command to disable debug tracing of DVMRP packet reception and transmission. Format no debug ip dvmrp packet [receive|transmit] Mode debug ip igmp packet Use this command to trace IGMP packet reception and transmission. receive traces only received IGMP [...]

Utility Commands 591 ProSafe M4100 and M7100 Managed Switches debug ip pimdm packet Use this command to trace PIMDM packet reception and transmission. receive traces only received PIMDM packets and transmit traces only transmitted PIMDM packets. When neither keyword is used in the command, then all PIMDM packet traces are dumped. Vital information [...]

Utility Commands 592 ProSafe M4100 and M7100 Managed Switches no debug ip vrrp Use this command to disable VRRP debug protocol messages. Format no debug ip vrrp Mode debug ipv6 dhcp Use this command to display “debug” information about DHCPv6 client activities and trace DHCPv6 packets to and from the local DHCPv6 client. Default Format debug ip[...]

Utility Commands 593 ProSafe M4100 and M7100 Managed Switches debug ipv6 mld packet Use this command to trace MLDv6 packet reception and transmission. receive traces only received MLDv6 packets and transmit traces only transmitted MLDv6 packets. When neither keyword is used in the command, then all MLDv6 packet traces are dumped. Vital information [...]

Utility Commands 594 ProSafe M4100 and M7100 Managed Switches no debug ipv6 pimsm packet Use this command to disable debug tracing of PIMSMv6 packet reception and transmission. Format no debug ipv6 pimsm packet [receive|transmit] Mode debug lacp packet This command enables tracing of LACP packets received and transmitted by the switch. Default Form[...]

Utility Commands 595 ProSafe M4100 and M7100 Managed Switches no debug mldsnooping packet Use this command to disable debug tracing of MLD snooping packet reception and transmission. debug ospf packet This command enables tracing of OSPF packets received and transmitted by the switch. Default Format debug ospf packet Mode Sample outputs of the trac[...]

Utility Commands 596 ProSafe M4100 and M7100 Managed Switches The remaining fields in the trace are specific to the type of OSPF Packet. HELLO packet field definitions: Netmask DesignRouter Backup DB_DSCR packet field definitions: MTU Options Flags • I – Init • M – More • MS – Master/Slave Seq LS_REQ packet field definitions. Length LS_[...]

Utility Commands 597 ProSafe M4100 and M7100 Managed Switches LS_ACK packet field definitions. Length no debug ospf packet This command disables tracing of OSPF packets. Format no debug ospf packet Mode debug ipv6 ospfv3 packet Use this command to enable OSPFv3 packet debug trace. Default Format debug ipv6 ospfv3 packet Mode no debug ipv6 ospfv3 pa[...]

Utility Commands 598 ProSafe M4100 and M7100 Managed Switches The following parameters are displayed in the trace message: TX/RX Intf SRC_IP DEST_IP Type no debug ping packet This command disables tracing of ICMP echo requests and responses. Format no debug ping packet Mode debug rip packet This command turns on tracing of RIP requests and response[...]

Utility Commands 599 ProSafe M4100 and M7100 Managed Switches The following parameters are displayed in the trace message: TX/RX Intf Src_IP Dest_IP Rip_Version Packet_Type Routes Number of routes not printed no debug rip packet This command disables tracing of RIP requests and responses. Format no debug rip packet Mode debug sflow packet Use this [...]

Utility Commands 600 ProSafe M4100 and M7100 Managed Switches debug spanning -tree bpdu This command enables tracing of spanning tree BPDUs received and transmitted by the switch. Default Format debug spanning-tree bpdu Mode no debug spanning-tree bpdu This command disables tracing of spanning tree BPDUs. Format no debug spanning-tree bpdu Mode deb[...]

Utility Commands 601 ProSafe M4100 and M7100 Managed Switches no debug spanning-tree bpdu receive This command disables tracing of received spanning tree BPDUs. Format no debug spanning-tree bpdu receive Mode debug spanning -tree bpdu transmit This command enables tracing of spanning tree BPDUs transmitted by the switch. Spanning tree should be ena[...]

Utility Commands 602 ProSafe M4100 and M7100 Managed Switches debug udld packet This command enables debugging on the received and transmitted UDLD PDU’ s. Format default udld packet receive Mode Default no debug udld packet This command disables debugging on the received and transmitted UDLD PDU’s. Format debug udld packet receive Mode debug u[...]

Utility Commands 603 ProSafe M4100 and M7100 Managed Switches debug aaa accounting This command is useful for debugging accounting configuration and functionality in User Manager . Format debug aaa accounting Mode no debug aaa accounting Use this command to turn off debugging of User Manager accounting functionality . Format no debug aaa accounting[...]

Utility Commands 604 ProSafe M4100 and M7100 Managed Switches cablestatus This command returns the status of the specified port. Format cablestatus <slot/port> Mode sFlow Commands sFlow ® is the standard for monitoring high-speed switched and routed networks. sFlow technology is built into network equipment and gives complete visibility into[...]

Utility Commands 605 ProSafe M4100 and M7100 Managed Switches no sflow receiver Use this command to set the sFlow collector parameters back to the defaults. Format no sflow receiver < indx > {ip < ip-address > | maxdatagram < size > | owner < string > timeout < interval > | port < 14-port >} Mode sflow sampler A [...]

Utility Commands 606 ProSafe M4100 and M7100 Managed Switches no sflow sampler Use this command to reset the sFlow sampler instance to the default settings. Format no sflow sampler {< rcvr-indx > | rate < sampling-rate > | maxheadersize < size >} Mode sflow poller A data source configured to collect counter samples is called a pol[...]

Utility Commands 607 ProSafe M4100 and M7100 Managed Switches show sflow agent The sFlow agent collects time-based sampling of network interface statistics and flow-based samples. These are sent to the configured sFlow receivers. Use this command to display the sFlow agent information. Format show sflow agent Mode Example: The following shows examp[...]

Utility Commands 608 ProSafe M4100 and M7100 Managed Switches show sflow receivers Use this command to display configuration information related to the sFlow receivers. Format show sflow receivers [<index>] Mode Example: The following shows example CLI display output for the command. (switch) #show sflow receivers 1 Receiver Index............[...]

Utility Commands 609 ProSafe M4100 and M7100 Managed Switches Software License Commands License commands allow you to configure advanced features on some layer2 managed switches. The following table lists the software license matrix for the layer2 managed switches. For details, see Licensing and Command Support on page 8. Managed Switches Note: The[...]

Utility Commands 610 ProSafe M4100 and M7100 Managed Switches (Managed Switches) # show license features This command displays the features that are licensed on the switch Format show license features Mode Example: The following shows example CLI display output for the command. (Managed Switches) #show license features IGMP MCAST PIMDM DVMRP PIMSM [...]

Utility Commands 61 1 ProSafe M4100 and M7100 Managed Switches clear ip address- conflict-detect This command clears the detected address conflict status information. Format clear ip address-conflict-detect Mode Link Local P rotocol Filtering Commands Link Local Protocol Filtering (LLPF) allows the switch to filter out multiple proprietary protocol[...]

Utility Commands 612 ProSafe M4100 and M7100 Managed Switches show llpf interface all Use this command to display the status of LLPF rules configured on a particular port or on all ports. Format show llpf interface [all | slot/port] Mode RMON Stats and History Commands The various MIBs within RFC 2819, 3273, and 3434 are arranged into groups. The m[...]

Utility Commands 613 ProSafe M4100 and M7100 Managed Switches • Group 9 - Event Controls the actions that are taken when an event occurs. RMON events occur when: • A threshold (alarm) is exceeded • There is a match on certain filters. RFC 3273 • Group 1 - Media Independent Group Contains media-independent statistics that provide information[...]

Utility Commands 614 ProSafe M4100 and M7100 Managed Switches no rmon alarm This command deletes the rmon alarm entry . Format no rmon alarm <alarm number> Mode rmon hcalarm This command sets the rmon hcalarm entry in the High Capacity RMON alarm mib group. Format rmon hcalarm <alarm number> <variable> <sample interval> <[...]

Utility Commands 615 ProSafe M4100 and M7100 Managed Switches no rmon hcalarm This command deletes the rmon hcalarm entry . Format no rmon hcalarm <alarm number> Mode rmon event This command sets the rmon event entry in the RMON event mib group. Format rmon event < event number > [description|log|owner|trap] Mode • None • Log • SN[...]

Utility Commands 616 ProSafe M4100 and M7100 Managed Switches rmon collection history This command sets the history control parameters of the RMON historyControl mib group. Format rmon collection history <index number> buckets <1-65535> | interval <1-3600> | owner <owner> Mode no rmon collection history This command deletes [...]

Utility Commands 617 ProSafe M4100 and M7100 Managed Switches show rmon history This command displays the specified entry in the RMON history table. Format show rmon history <index> {errors|other|throughput} Mode Example: (Swtich) # show rmon history 1 throughput Sample set: 1 Maximum table size: 270 Time Octets Packets Broadcast Multicast Ut[...]

Utility Commands 618 ProSafe M4100 and M7100 Managed Switches show rmon {hcalarms | hcalarm <alarm index>} This command displays the entries in the RMON hcAlarmT able. Format show rmon {hcalarms | hcalarm <alarm index>} Mode UDLD Commands The UDLD feature detects unidirectional links physical ports. A unidirectional link is a forwarding[...]

Utility Commands 619 ProSafe M4100 and M7100 Managed Switches udld timeout interval This command configures the time interval after which UDLD link is considered to be unidirectional. The range is from 5 to 60 seconds. Default Format udld timeout interval <interval> Mode udld enable This command enables UDLD on the specified interface. Defaul[...]

Utility Commands 620 ProSafe M4100 and M7100 Managed Switches show udld This command displays the global settings of UDLD. Format show udld Mode Admin Mode Message Interval Timeout Interval show udld <slot/port> This command displays the UDLD settings for the specified <slot/port>. If the “all” keyword is entered, it displays inform[...]

Utility Commands 621 ProSafe M4100 and M7100 Managed Switches show usb device This command displays USB flash device details. Format show USB device Mode Device Status • Active . Device is plugged in and the device is recognized if device is not mounted. • Inactive . Device is not mounted. • Invalid . Device is not present or invalid device i[...]

Filename Filesize Total Size Bytes Used Bytes Free Utility Commands 622 ProSafe M4100 and M7100 Managed Switches Example: (switch) #dir USB: Filename Filesize Modification Time F1.cfg 256 4/22/2009 8:00:12 Total Size: xxxx Bytes Used: yyyy Bytes Free: zzzz Parameter Description File name File size USB flash device storage size Indicates size of mem[...]

623 11 1 1. M anage men t C omman ds This chapter describes the management commands available in the managed switch CLI. This chapter contains the following sections: • Configuring the Switch Management CPU • Network Interface Commands • Console Port Access Commands • T elnet Commands • Secure Shell (SSH) Commands • Management Security [...]

Management Commands 624 ProSafe M4100 and M7100 Managed Switches Configuring the Switch Management CPU T o manage the switch via the web GUI or telnet, an IP address needs to be assigned to the switch management CPU. Whereas there are CLI commands that can be used to do this, ezconfig simplifies the task. The tool is applicable to all NETGEAR 7000-[...]

Management Commands 625 ProSafe M4100 and M7100 Managed Switches The following is an example of an ezconfig session. NETGEAR EZ Configuration Utility -------------------------------- Hello and Welcome! This utility will walk you thru assigning the IP address for the switch management CPU. It will allow you to save the changes at the end. After the [...]

Management Commands 626 ProSafe M4100 and M7100 Managed Switches Network Interface Commands This section describes the commands you use to configure a logical interface for management access. T o configure the management VLAN, see step on page 47. enable (P rivileged EXEC access) Use this command to access the Privileged EXEC mode. From the Privile[...]

Management Commands 627 ProSafe M4100 and M7100 Managed Switches A locally administered address must have bit 6 On (b'1') and bit 7 Off (b'0'). Format network mac-address <macaddr> Mode network mac-type Use this command to specify whether the switch uses the burned in MAC address or the locally administered MAC address. De[...]

Management Commands 628 ProSafe M4100 and M7100 Managed Switches the switch's network interface do not affect the configuration of the front panel ports through which traffic is switched or routed. The network interface is always considered to be up, whether any member ports are up; therefore, the show network command will always show “Inter[...]

Management Commands 629 ProSafe M4100 and M7100 Managed Switches IPv6 Address/Length is ........................ 3099::210:18FF:FE82:337/64 IPv6 Default Router is ........................ FE80::204:76FF:FE73:423A Burned In MAC Address.......................... 00:10:18:82:03:37 Locally Administered MAC Address............... 00:00:00:00:00:00 MAC A[...]

Management Commands 630 ProSafe M4100 and M7100 Managed Switches no serial baudrate Use this command to set the communication rate of the terminal interface. Format no serial baudrate Mode serial timeout Use this command to specify the maximum connect time (in minutes) without console activity . A value of 0 indicates that a console can be connecte[...]

Management Commands 631 ProSafe M4100 and M7100 Managed Switches enable authentication Use this command in line configuration mode to specify an authentication method list when the user accesses a higher privilege level in remote telnet or console. Format enable authentication {default | list-name } Mode no enable authentication Use this command to[...]

Management Commands 632 ProSafe M4100 and M7100 Managed Switches ip telnet server enable Use this command to enable T elnet connections to the system and to enable the T elnet Server Admin Mode. This command opens the T elnet listening port. Default Format ip telnet server enable Mode no ip telnet server enable Use this command to disable T elnet a[...]

Management Commands 633 ProSafe M4100 and M7100 Managed Switches no transport input telnet Use this command to prevent new T elnet sessions from being established. Format no transport input telnet Mode transport output telnet Use this command to regulate new outbound T elnet connections. If enabled, new outbound T elnet sessions can be established [...]

Management Commands 634 ProSafe M4100 and M7100 Managed Switches no session-limit Use this command to set the maximum number of simultaneous outbound T elnet sessions to the default value. Format no session-limit Mode session-timeout Use this command to set the T elnet session timeout value. The timeout value unit of time is minutes. Default Format[...]

Management Commands 635 ProSafe M4100 and M7100 Managed Switches telnetcon timeout Use this command to set the T elnet connection session timeout value, in minutes. A session is active as long as the session has not been idle for the value set. The time is a decimal value from 1 to 160. Note: When you change the timeout value, the new value is appl[...]

Outbound Telnet Login Timeout Maximum Number of Outbound Telnet Sessions Allow New Outbound Telnet Sessions Management Commands 636 ProSafe M4100 and M7100 Managed Switches show telnetcon Use this command to display the current inbound T elnet settings. In other words, these settings apply to T elnet connections initiated from a remote system to th[...]

Management Commands 637 ProSafe M4100 and M7100 Managed Switches ip ssh Use this command to enable SSH access to the system. (This command is the short form of the ip ssh server enable command.) Default Format ip ssh Mode ip ssh protocol Use this command to set or remove protocol levels (or versions) for SSH. Either SSH1 (1), SSH2 (2), or both SSH [...]

Management Commands 638 ProSafe M4100 and M7100 Managed Switches no sshcon maxsessions Use this command to set the maximum number of allowed SSH connection sessions to the default value. Format no sshcon maxsessions Mode sshcon timeout Use this command to set the SSH connection session timeout value, in minutes. A session is active as long as the s[...]

Management Commands 639 ProSafe M4100 and M7100 Managed Switches Management Security Commands This section describes commands you use to generate keys and certificates, which you can do in addition to loading them as before. crypto certificate generate Use this command to generate self-signed certificate for HTTPS. The generate RSA key for SSL has [...]

Management Commands 640 ProSafe M4100 and M7100 Managed Switches no crypto key generate rsa Use this command to delete the RSA key files from the device. Format no crypto key generate rsa Mode crypto key generate dsa Use this command to generate a DSA key pair for SSH. The new key files will overwrite any existing generated or downloaded DSA key fi[...]

Management Commands 641 ProSafe M4100 and M7100 Managed Switches no ip http server Use this command to disable access to the switch through the Web interface. When access is disabled, the user cannot login to the switch's W eb server . Format no ip http server Mode ip http secure- server Use this command to enable the secure socket layer for s[...]

Management Commands 642 ProSafe M4100 and M7100 Managed Switches user will be forced to reauthenticate. This timer begins on initiation of the web session and is unaffected by the activity level of the connection. Format ip http session hard-timeout <0-168> Mode no ip http session hard-timeout Use this command to restore the hard timeout for [...]

Management Commands 643 ProSafe M4100 and M7100 Managed Switches ip http session maxsessions Use this command to limit the number of allowable unsecure HTTP sessions. Zero is the configurable minimum. Format ip http session maxsessions <0-16> Mode no ip http session maxsessions Use this command to restore the number of allowable unsecure HTTP[...]

Management Commands 644 ProSafe M4100 and M7100 Managed Switches no ip http secure-session maxsessions Use this command to restore the number of allowable secure HTTP sessions to the default value. Format no ip http secure-session maxsessions Mode ip http secure- session soft-timeout Use this command to configure the soft timeout for secure HTTP se[...]

Management Commands 645 ProSafe M4100 and M7100 Managed Switches ip https authentication Use this command to specify the authentication methods for http server users. The additional methods of authentication are used only if the previous method returns an error , not if it fails. T o ensure that the authentication succeeds even if all methods retur[...]

Management Commands 646 ProSafe M4100 and M7100 Managed Switches ip http secure-protocol Use this command to set protocol levels (versions). The protocol level can be set to TLS1, SSL3 or to both TLS1 and SSL3. Default Format ip http secure-protocol [SSL3] [TLS1] Mode show ip http Use this command to display the http settings for the switch. Format[...]

Management Commands 647 ProSafe M4100 and M7100 Managed Switches Access Commands Use the commands in this section to close remote connections or to view information about connections to the system. disconnect Use the disconnect command to close HTTP , HTTPS, T elnet, or SSH sessions. Use all to close all active sessions, or use <session-id> t[...]

Management Commands 648 ProSafe M4100 and M7100 Managed Switches username Use this command to add a new user to the local user database. The default privilege level is 1. Using the encrypted keyword allows the administrator to transfer local user passwords between devices without having to know the passwords. When the password parameter is used alo[...]

Management Commands 649 ProSafe M4100 and M7100 Managed Switches username name nopassword Use this command to remove an existing user ’s password (NULL password). Format username name nopassword [ Level Level ] Mode username <username> unlock Use this command to unlock a user ’s account. Only a user with read/write access can reactivate a[...]

Management Commands 650 ProSafe M4100 and M7100 Managed Switches username snmpv3 authentication Use this command to specify the authentication protocol to be used for the specified user . The valid authentication protocols are none , md5 or sha . If you specify md5 or sha , the login password is also used as the snmpv3 authentication password and t[...]

Management Commands 651 ProSafe M4100 and M7100 Managed Switches no username snmpv3 encryption Use this command to set the encryption protocol to none . The <username> is the login user name for which the specified encryption protocol will be used. Format no username snmpv3 encryption <username> Mode show users Use this command to displ[...]

Management Commands 652 ProSafe M4100 and M7100 Managed Switches show users accounts detail This command displays the local user status about user account lockout and password aging. It also includes information about Password strength and complexity . Format show users accounts detail Mode (Switch) #show users accounts detail UserName.............[...]

Login Time Username Protocol Location Management Commands 653 ProSafe M4100 and M7100 Managed Switches passwords min-length Use this command to enforce a minimum password length for local users. The value also applies to the enable password. The valid range is 0–64. Default Format passwords min-length <0-64> Mode no passwords min-length Use[...]

Management Commands 654 ProSafe M4100 and M7100 Managed Switches passwords aging Use this command to implement aging on passwords for local users. When a user ’s password expires, the user will be prompted to change it before logging in again. The valid range is 1-365. The default is 0, or no aging. Default Format passwords aging <1-365> Mo[...]

Management Commands 655 ProSafe M4100 and M7100 Managed Switches no passwords strength-check Use this command to disable the password strength-check. Format no passwords strength-check Mode passwords strength minimum uppercase-letters Use this command to enforce a minimum number of uppercase letters that a password should contain. The valid range i[...]

Management Commands 656 ProSafe M4100 and M7100 Managed Switches passwords strength minimum numeric-characters Use this command to enforce a minimum number of numeric characters that a password should contain. The valid range is 0-16. The default is 2. Minimum of 0 means no restriction on that set of characters. Format passwords strength minimum nu[...]

Management Commands 657 ProSafe M4100 and M7100 Managed Switches no passwords strength maximum consecutive-characters Use this command to reset the maximum number of consecutive characters to the default value. Format no passwords strength maximum consecutive-characters Mode passwords strength maximum repeated-characters Use this command to enforce[...]

Management Commands 658 ProSafe M4100 and M7100 Managed Switches passwords strength exclude-keyword Use this command to exclude the specified keyword while configuring the password. The password does not accept the keyword in any form (in between the string, case insensitive and reverse) as a substring. User can configure up to a maximum of 3 keywo[...]

Management Commands 659 ProSafe M4100 and M7100 Managed Switches show passwords result Use this command to display the last password set result information. Format show passwords result Mode Last User Whose Password Is Set Password Strength Check Last Password Set Result aaa authentication login Use this command to set authentication at login. The [...]

Management Commands 660 ProSafe M4100 and M7100 Managed Switches list-name Character string used to name the list of authentication methods activated when a user logs in. Up to 12 characters. method1 [method2…] At least one from the following table: enable line local none radius tacacs Note: The local user database is checked. This has the same e[...]

Management Commands 661 ProSafe M4100 and M7100 Managed Switches Default Uses the listed authentication methods that follow this argument as the default list of methods when a user accesses a higher privilege level. list-name Character string used to name the list of authentication methods activated when a user accesses a higher privilege level. Up[...]

Management Commands 662 ProSafe M4100 and M7100 Managed Switches specified as an authentication method after radius, no authentication is used if the radius server is down. Format aaa authentication dot1x default method1 Mode method1: At least one from the following table: local none radius ias no aaa authentication dot1x Use this command to remove[...]

exec commands default list-name start-stop stop-only none method ( method1/method2 …) Management Commands 663 ProSafe M4100 and M7100 Managed Switches no aaa accounting This command deletes the accounting method list. Format no aaa accounting {exec | commands} {list_name default} Mode accounting (Console/T elnet/SSH) This command applies the acco[...]

Management Commands 664 ProSafe M4100 and M7100 Managed Switches ip http/https accounting This command applies user exec accounting list to the line methods HTTP and HTTPs methods. Format ip {http| https} accounting exec {default| <listname>} Mode HTTP/HTTPS default list-name no ip http/https accounting exec This command deletes the authoriza[...]

Management Commands 665 ProSafe M4100 and M7100 Managed Switches Example: (switch) # (switch) #show accounting methods Acct Type Method Name Record Type Method Type ---------- ------------ ------------ ------------ Exec dfltExecList start-stop TACACS Commands dfltCmdsList stop-only TACACS Commands UserCmdAudit start-stop TACACS Line EXEC Method Lis[...]

Management Commands 666 ProSafe M4100 and M7100 Managed Switches no aaa authorization This command deletes the authorization method list. Format no aaa authorization {commands | exec } {default | <list_name>} method1[method2] Mode authorization(console/telnet/ssh) T o apply the command authorization method list to an access method (console/te[...]

Management Commands 667 ProSafe M4100 and M7100 Managed Switches ---------------------------- ------------------------------ dfltExecAuthList none undefined undefined undefined Line Exec Method List --------- --------------------- Console dfltExecAuthList Telnet dfltExecAuthList SSH dfltExecAuthList domain-name Managed switch supports authenticatio[...]

Management Commands 668 ProSafe M4100 and M7100 Managed Switches no domain-name enable This command disables the domain name functionality . Format no domain-name enable Mode show domain-name This command displays the configured domain-name. Format show domain-name Mode Example: (switch) # (switch) #show domain-name Domain : Enable Domain-name :abc[...]

Management Commands 669 ProSafe M4100 and M7100 Managed Switches aaa session-id This global aaa command specifies whether the same session-id is used for Authentication, Authorization, and Accounting service type within a session. Default common Format aaa session-id [common | unique] Mode common unique no aaa session-id This command resets the aaa[...]

Management Commands 670 ProSafe M4100 and M7100 Managed Switches clear aaa ias-users Use this command to remove all users from the IAS database. Format clear aaa ias-users Mode show aaa ias-users Use this command to display configured IAS users and their attributes. Passwords configured are not shown in the show command output. Format show aaa ias-[...]

Management Commands 671 ProSafe M4100 and M7100 Managed Switches no snmp-server community Use this command to remove this community name from the table. The <name> is the community name to be deleted. Format no snmp-server community <name> Mode snmp- server community ipaddr Use this command to set a client IP address for an SNMP communi[...]

Management Commands 672 ProSafe M4100 and M7100 Managed Switches station, and will use that machine's IP address for the client IP address. A value of 0.0.0.0 will allow access from any IP address. The name is the applicable community name. Default Format snmp-server community ipmask <ipmask> <name> Mode no snmp-server community ip[...]

Management Commands 673 ProSafe M4100 and M7100 Managed Switches snmp- server community ro Use this command to restrict access to switch information. The access mode is read-only (also called public). Format snmp-server community ro <name> Mode snmp- server community rw Use this command to restrict access to switch information. The access mod[...]

Management Commands 674 ProSafe M4100 and M7100 Managed Switches no snmp-server enable traps Use this command to disable the Authentication Flag. Format no snmp-server enable traps Mode Note: This command might not be available on all platforms. snmp- server enable traps linkmode Use this command to enable Link Up/Down traps for the entire switch. [...]

Management Commands 675 ProSafe M4100 and M7100 Managed Switches no snmp-server enable traps multiusers Use this command to disable Multiple User traps. Format no snmp-server enable traps multiusers Mode snmp- server enable traps stpmode Use this command to enable sending new root traps and topology change notification traps. Default Format snmp-se[...]

Management Commands 676 ProSafe M4100 and M7100 Managed Switches no snmptrap Use this command to delete trap receivers for a community . Format no snmptrap <name> {ipaddr <ipaddr|hostname> | ip6addr <ip6addr| hostname>} Mode snmptrap snmpversion Use this command to modify the SNMP version of a trap. The maximum length of <name&[...]

Management Commands 677 ProSafe M4100 and M7100 Managed Switches snmptrap mode Use this command to activate or deactivate an SNMP trap. Enabled trap receivers are active (able to receive traps). Disabled trap receivers are inactive (not able to receive traps). Format snmptrap mode <name> { <ipaddr | hostname> |<ip6addr |hostname>}[...]

Management Commands 678 ProSafe M4100 and M7100 Managed Switches snmp trap link - status all Use this command to enable link status traps for all interfaces. Note: This command is valid only when the Link Up/Down Flag is enabled. For more information, see snmp-server enable traps linkmode on page 674. no snmp trap link-status all Use this command t[...]

Management Commands 679 ProSafe M4100 and M7100 Managed Switches TCP/IP to an external SNMP manager based on the SNMP configuration (the trap receiver and other SNMP community parameters). Format show snmpcommunity Mode SNMP Community Name Client IP Address Client IP Mask Access Mode Status show snmptrap Use this command to display SNMP trap receiv[...]

Management Commands 680 ProSafe M4100 and M7100 Managed Switches Community Name IpAddress IPv6 Address Snmp Version Mode Mytrap 0.0.0.0 2001::1 SNMPv2 Enable show trapflags show trapflags Use this command to display trap conditions. The command’ s display shows all the enabled OSPFv2 and OSPFv3 trapflags. Configure which traps the switch should g[...]

Management Commands 681 ProSafe M4100 and M7100 Managed Switches authorization network radius Use this command to enable the switch to accept VLAN assignment by the radius server . Default Format authorization network radius Mode no authorization network radius Use this command to disable the switch to accept VLAN assignment by the radius server . [...]

Management Commands 682 ProSafe M4100 and M7100 Managed Switches no radius server attribute Use the no version of this command to disable the NAS-IP-Address attribute global parameter for RADIUS client. When this parameter is disabled, the RADIUS client does not send the NAS-IP-Address attribute in RADIUS requests. Format no radius server attribute[...]

Management Commands 683 ProSafe M4100 and M7100 Managed Switches Note: T o reconfigure a RADIUS accounting server to use the default UDP <port> , set the <port> parameter to 1813. no radius server host Use the no version of this command to delete the configured server entry from the list of configured RADIUS servers. If the RADIUS authe[...]

Management Commands 684 ProSafe M4100 and M7100 Managed Switches radius server key Use this command to configure the key to be used in RADIUS client communication with the specified server . Depending on whether the 'auth' or 'acct' token is used, the shared secret is configured for the RADIUS authentication or RADIUS accounting[...]

Management Commands 685 ProSafe M4100 and M7100 Managed Switches no radius server msgauth Use the no version of this command to disable the message authenticator attribute to be used for the specified RADIUS Authenticating server . Format no radius server msgauth <ipaddr|dnsname> Mode radius server primary Use this command to designate a conf[...]

Management Commands 686 ProSafe M4100 and M7100 Managed Switches no radius server retransmit Use this command to set the value of this global parameter to the default value. Format no radius server retransmit Mode radius server timeout Use this command to configure the global parameter for the RADIUS client that specifies the timeout value (in seco[...]

Number of Configured Authentication Servers Number of Configured Accounting Servers Number of Named Authentication Server Groups Number of Named Accounting Server Groups Number of Retransmits Time Duration RADIUS Accounting Mode RADIUS Attribute 4 Mode RADIUS Attribute 4 Value Management Commands 687 ProSafe M4100 and M7100 Managed Switches The fol[...]

Management Commands 688 ProSafe M4100 and M7100 Managed Switches The following shows example CLI display output for the command. (Switch) #show radius servers Cur Host Address Server Name Port Type rent ---- ------------------------ --------------------------------- ----- ---------- * 192.168.37.200 Network1_RADIUS_Server 1813 Primary 192.168.37.20[...]

Management Commands 689 ProSafe M4100 and M7100 Managed Switches 192.168.37.201 Network2_RADIUS_Server Primary 192.168.37.202 Network3_RADIUS_Server Secondary 192.168.37.203 Network4_RADIUS_Server Primary (Switch) #show radius servers name Default_RADIUS_Server Server Name............................ Default_RADIUS_Server Host Address..............[...]

Management Commands 690 ProSafe M4100 and M7100 Managed Switches The following shows example CLI display output for the command. (Switch) #show radius accounting name Host Address Server Name Port Secret Configured ----------------------- --------------------------------- -------- ----------- 192.168.37.200 Network1_RADIUS_Server 1813 Yes 192.168.3[...]

Management Commands 691 ProSafe M4100 and M7100 Managed Switches The following shows example CLI display output for the command. (Switch) #show radius accounting statistics 192.168.37.200 RADIUS Accounting Server Name................. Default_RADIUS_Server Host Address.................................. 192.168.37.200 Round Trip Time................[...]

Management Commands 692 ProSafe M4100 and M7100 Managed Switches Malformed Responses........................... 0 Bad Authenticators............................ 0 Pending Requests.............................. 0 Timeouts...................................... 0 Unknown Types................................. 0 Packets Dropped.........................[...]

Management Commands 693 ProSafe M4100 and M7100 Managed Switches The following shows example CLI display output for the command. (Switch) #show radius statistics 192.168.37.200 RADIUS Server Name............................ Default_RADIUS_Server Server Host Address........................... 192.168.37.200 Access Requests...........................[...]

Management Commands 694 ProSafe M4100 and M7100 Managed Switches debug tacacs packet Use the debug tacacs packet command to turn on T ACACS+ packet debug. Default Format debug tacacs packet [receive | transmit] Mode no debug tacacs packet Use this command to turn off T ACACS+ packet debug. Format no debug tacacs packet Mode tacacs- server host Use [...]

Management Commands 695 ProSafe M4100 and M7100 Managed Switches keyword. In the show running config command’s display , these secret keys are displayed in encrypted format. Y ou cannot show these keys in plain text format. Format tacacs-server key [< key-string> | encrypted <key-string>] Mode no tacacs-server key Use the no tacacs-se[...]

Management Commands 696 ProSafe M4100 and M7100 Managed Switches no tacacs-server source interface Use this command in Global Configuration mode to remove the global source interface (Source IP selection) for all T ACACS+ communications between the T ACACS+ client and the server . Format no tacacs-server source-interface Mode tacacs- server timeout[...]

Management Commands 697 ProSafe M4100 and M7100 Managed Switches port Use the port command in T ACACS Configuration mode to specify a server port number . The server <port-number> range is 0 - 65535. Default Format port <port-number> Mode priority Use the priority command in T ACACS Configuration mode to specify the order in which serve[...]

Management Commands 698 ProSafe M4100 and M7100 Managed Switches Configuration Scripting Commands Configuration Scripting allows you to generate text-formatted script files representing the current configuration of a system. Y ou can upload these configuration script files to a computer or UNIX system and edit them. Then, you can download the edite[...]

Management Commands 699 ProSafe M4100 and M7100 Managed Switches " " hello hello script apply Use this command to apply the commands in the script to the switch. The <scriptname> parameter is the name of the script to apply . Format script apply <scriptname> Mode script delete Use this command to delete a specified script, whe[...]

Management Commands 700 ProSafe M4100 and M7100 Managed Switches script validate Use this command to validate a script file by parsing each line in the script file, where <scriptname> is the name of the script to validate. The validate option is intended to be used as a tool for script development. V alidation identifies potential problems. I[...]

Management Commands 701 ProSafe M4100 and M7100 Managed Switches set clibanner Use this command to add the CLI Banner . The banner message supports up to 2000 characters. Format set clibanner < line > Mode no set clibanner Use this command to remove the CLI Banner downloaded through TFTP . Format no set clibanner Mode Switch Database Manageme[...]

ipv4-routing dual-ipv4-and-ipv 6 Management Commands 702 ProSafe M4100 and M7100 Managed Switches no sdm prefer Use this command to return to the default template. Format no sdm prefer Mode show sdm prefer Use this command to view the currently active SDM template and its scaling parameters, or to view the scaling parameters for an inactive templat[...]

Management Commands 703 ProSafe M4100 and M7100 Managed Switches Example: #show sdm prefer Current template: Dual IPv4 and IPv6 ARP Entries.................................... 4096 IPv4 Unicast Routes............................ 6112 IPv6 NDP Entries............................... 2048 IPv6 Unicast Routes............................ 3072 ECMP Next [...]

Management Commands 704 ProSafe M4100 and M7100 Managed Switches network ipv6 address Use this command to configure an IPv6 global address, enable or disable stateless global address autoconfiguration, and enable or disable dhcpv6 client protocol information for the network port. Y ou can configure multiple IPv6 addresses on the network port. Forma[...]

Management Commands 705 ProSafe M4100 and M7100 Managed Switches no network ipv6 gateway Use this command to remove IPv6 gateways on the network port interface. Format no network ipv6 gateway Mode show network ndp Use this command to display NDP cache information for the network port. Default Format show network ndp Mode • Privileged EXEC • Use[...]

Management Commands 706 ProSafe M4100 and M7100 Managed Switches The following example shows CLI display output for the command: (switch)#show network ipv6 dhcp statistics DHCPv6 Client Statistics ------------------------- DHCPv6 Advertisement Packets Received................. 0 DHCPv6 Reply Packets Received......................... 0 Received DHCP[...]

Management Commands 707 ProSafe M4100 and M7100 Managed Switches clear network ipv6 dhcp statistics Use this command to clear the DHCPv6 statistics on the network management interface. Format clear network ipv6 dhcp statistics Mode Privileged EXEC[...]

708 12 12. L og M ess age s This chapter lists common log messages, along with information regarding the cause of each message. There is no specific action that can be taken per message. When there is a problem being diagnosed, a set of these messages in the event log, along with an understanding of the system configuration and details of the probl[...]

Log Messages 709 ProSafe M4100 and M7100 Managed Switches Core T able 3. BSP Log Messages Component Message Cause BSP Event(0xaaaaaaaa) Switch has restarted. BSP Starting code... BSP initialization complete, starting 7000 series application. T able 4. NIM Log Messages Component Message Cause NIM NIM: L7_A TT ACH out of order for intIfNum(x) unit x [...]

Log Messages 710 ProSafe M4100 and M7100 Managed Switches T able 5. System Log Messages Component Message Cause SYSTEM Configuration file Switch CLI.cfg size is 0 (zero) bytes The configuration file could not be read. This message might occur on a system for which no configuration has ever been saved or for which configuration has been erased. SYST[...]

Log Messages 71 1 ProSafe M4100 and M7100 Managed Switches Utilities T able 6. T rap Mgr Log Message Component Message Cause Trap Mgr Link Up/Down: slot/port An interface changed link state. T able 7. DHCP Filtering Log Messages Component Message Cause DHCP Filtering Unable to create r/w lock for DHCP Filtering Unable to create semaphore used for d[...]

Log Messages 712 ProSafe M4100 and M7100 Managed Switches T able 9. RADIUS Log Messages Component Message Cause RADIUS RADIUS: Invalid data length - xxx The RADIUS Client received an invalid message from the server . RADIUS RADIUS: Failed to send the request A problem communicating with the RADIUS server . RADIUS RADIUS: Failed to send all of the r[...]

Log Messages 713 ProSafe M4100 and M7100 Managed Switches Management T able 10. T ACACS+ Log Messages Component Message Cause TACACS+ T ACACS+: authentication error , no server to contact T ACACS+ request needed, but no servers are configured. TACACS+ T ACACS+: connection failed to server x.x.x.x T ACACS+ request sent to server x.x.x.x but no respo[...]

Log Messages 714 ProSafe M4100 and M7100 Managed Switches T able 14. EmW eb Log Messages Component Message Cause EmWeb EMWEB (T elnet): Max number of T elnet login sessions exceeded A user attempted to connect via telnet when the maximum number of telnet sessions were already active. EmWeb EMWEB (SSH): Max number of SSH login sessions exceeded A us[...]

Log Messages 715 ProSafe M4100 and M7100 Managed Switches T able 16. WEB Log Messages Component Message Cause WEB Max clients exceeded This message is shown when the maximum allowed java client connections to the switch is exceeded. WEB Error on send to sockfd XXXX, closing connection Failed to send data to the java clients through the socket. WEB [...]

Log Messages 716 ProSafe M4100 and M7100 Managed Switches SSHD SSHD: Unknown UI event in message, event=XXXX Failed to dispatch the UI event to the appropriate SSHD function as it’s an invalid event. XXXX indicates the event to be dispatched. SSHD sshdApiCnfgrCommand: Failed calling sshdIssueCmd. Failed to send the message to the SSHD message que[...]

Log Messages 717 ProSafe M4100 and M7100 Managed Switches Switching T able 20. User_Manager Log Messages Component Message Cause User_Manager User Login Failed for XXXX Failed to authenticate user login. XXXX indicates the user name to be authenticated. User_Manager Access level for user XXXX could not be determined. Setting to READ_ONL Y . Invalid[...]

Log Messages 718 ProSafe M4100 and M7100 Managed Switches T able 22. IP Subnet VLANS Log Messages Component Message Cause IPsubnet vlans ERROR vlanIpSubnetSubnetV alid :Invalid subnet Occurs when an invalid pair of subnet and netmask has come from the CLI IPsubnet vlans IP Subnet Vlans: failed to save configuration This message appears when save co[...]

Log Messages 719 ProSafe M4100 and M7100 Managed Switches Mac based VLANS vlanMacVlanChangeCallback: Failed to add an entry Appears when a dtl fails to add an entry for a VLAN add notify event. Mac based VLANS vlanMacVlanChangeCallback: Failed to delete an entry Appears when a dtl fails to delete an entry for an VLAN delete notify event. T able 24.[...]

Log Messages 720 ProSafe M4100 and M7100 Managed Switches IGMP Snooping Failed to set igmp mrouter mode %d for interface xxx on VLAN yyy Failed to set VLAN multicast router mode due to IGMP Snooping message queue being full IGMP Snooping snoopCnfgrInitPhase1Process: Error allocating small buffers Could not allocate buffers for small IGMP packets IG[...]

Log Messages 721 ProSafe M4100 and M7100 Managed Switches T able 27. 802.3ad Log Messages Component Message Cause 802.3ad dot3adReceiveMachine: received default event %x Received a LAG PDU and the RX state machine is ignoring this LAGPDU 802.3ad dot3adNimEventCompletionCallback, dot3adNimEventCreateCompletionCallbac k: DOT3AD: notification failed f[...]

Log Messages 722 ProSafe M4100 and M7100 Managed Switches T able 32. 802.1Q Log Messages Component Message Cause 802.1Q dot1qIssueCmd: Unable to send message %d to dot1qMsgQueue for vlan %d - %d msgs in queue dot1qMsgQueue is full. 802.1Q dot1qVlanCreateProcess: Attempt to create a vlan with an invalid vlan id %d ; VLAN %d not in range, Accommodate[...]

Log Messages 723 ProSafe M4100 and M7100 Managed Switches QoS T able 35. Protocol-based VLANs Log Messages Component Message Cause Protocol Based VLANs pbVlanCnfgrInitPhase2Process: Unable to register NIM callback Appears when nimRegisterIntfChange fails to register pbVlan for link state changes. Protocol Based VLANs pbVlanCnfgrInitPhase2Process: U[...]

Log Messages 724 ProSafe M4100 and M7100 Managed Switches R outing/IPv6 R outing T able 38. DiffServ Log Messages Component Message Cause DiffServ diffserv .c 165: diffServRestore Failed to reset DiffServ . Recommend resetting device While attempting to clear the running configuration an error was encountered in removing the current settings. This [...]

Log Messages 725 ProSafe M4100 and M7100 Managed Switches OSPFv2 W arning: OSPF LSDB is 90% full (22648 LSAs). OSPFv2 limits the number of Link State Advertisements (LSAs) that can be stored in the link state database (LSDB). When the database becomes 90 or 95 percent full, OSPFv2 logs this warning. The warning includes the current size of the data[...]

Log Messages 726 ProSafe M4100 and M7100 Managed Switches T able 42. Routing T able Manager Log Messages Component Message Cause Routing Table Manager RT O is full. Routing table contains 8000 best routes, 8000 total routes. The routing table manager , also called “RT O,” stores a limited number of best routes, based on hardware capacity . When[...]

Log Messages 727 ProSafe M4100 and M7100 Managed Switches Multicast T able 45. RIP Log Message Component Message Cause RIP RIP : discard response from xxx via unexpected interface When RIP response is received with a source address not matching the incoming interface’s subnet. T able 46. DHCP6 Log Message Component Message Cause DHCP6 relay_to_se[...]

Log Messages 728 ProSafe M4100 and M7100 Managed Switches T able 49. IGMP-Proxy Log Messages Component Message Cause IGMP-Proxy Error getting memory for igmp host group record When we are unable to allocate memory for the IGMP group record in the Host (Proxy) table IGMP-Proxy Error getting memory for source record When we are unable to allocate mem[...]

Log Messages 729 ProSafe M4100 and M7100 Managed Switches Stacking T able 51. PIM-DM Log Messages Component Message Cause PIM-DM Out of memory when creating xxx This message is logged when there is insufficient memory to accommodate a new neighbor/(S,G) Entry , Prune, Graft, Join etc. PIM-DM Error entry->ll_xxx LL creation error This message is [...]

Log Messages 730 ProSafe M4100 and M7100 Managed Switches T echnologies T able 54. System General Error Messages Component Message Cause OS Invalid USP unit = x, slot = x, port =x A port was not able to be translated correctly during the receive. OS In hapiBroadSystemMacAddress call to 'bcm_l2_addr_add' - F AILED : x Failed to add an L2 a[...]

Log Messages 731 ProSafe M4100 and M7100 Managed Switches OS USL: A T runk being created by bcmx already existed in USL Possible synchronization issue between the application, hardware, and sync layer OS USL: A T runk being destroyed doesn't exist in USL Possible synchronization issue between the application, hardware, and sync layer . OS USL:[...]

Log Messages 732 ProSafe M4100 and M7100 Managed Switches O/S Support OS USL: failed to sync L3 Route table on unit= x Could not synchronize unit x due to a transport failure or API issue on remote unit. A synchronization retry will be issued OS USL: failed to sync initiator table on unit=x Could not synchronize unit x due to a transport failure or[...]

Log Messages 733 ProSafe M4100 and M7100 Managed Switches OSAPI osapiCleanupIf: NetIPGet During the call to remove the interface from the route table, the attempt to get an ipv4 interface address from the stack failed. OSAPI osapiCleanupIf: NetMaskGet During the call to remove the interface from the route table ,the attempt to get the ipv4 interfac[...]

734 13 13. Gr ee n Ethe r net C ommands NETGEAR Managed Switch Release 10.0.1 supports the following Green Ethernet power saving modes: • Energy Detect Mode • EEE Mode The Green Ethernet commands supported depends on the switch model T able 56. Green feature support Model Energy-Detect EEE M4100-D10-POE Y es No M4100-D12G Y es Y es M4100-50G-PO[...]

Green Ethernet Commands 735 ProSafe M4100 and M7100 Managed Switches Energy -Detect Mode When Energy-Detect mode is enabled, if communication on a port stops, the port circuitry automatically shuts down for a short period. The port wakes up periodically to check for link activity . If activity is detected, the port circuitry remains active. This al[...]

Green Ethernet Commands 736 ProSafe M4100 and M7100 Managed Switches green-mode energy - detect Use this command enables energy-detect mode on an interface or on all the interfaces. Format green-mode energy-detect Mode Default no green-mode energy-detect This command disables energy-detect mode on an interface or on all the interfaces. Format no gr[...]

Green Ethernet Commands 737 ProSafe M4100 and M7100 Managed Switches clear green-mode statistics This command to clears the following for a specified <slot/port> , or for all ports: • EEE LPI event count, and LPI duration • EEE LPI history table entries • Cumulative Power savings estimates Format clear green-mode statistics {<slot/po[...]

Green Ethernet Commands 738 ProSafe M4100 and M7100 Managed Switches EEE EEE Admin Mode EEE Admin Mode is enabled or disabled. T ransmit Idle T ime It is the time for which condition to move to LPI state is satisfied, at the end of which MAC TX transitions to LPI state. The Range is (0 to 0xff f ffff f).The default value is 0. T ransmit W ake T ime[...]

Green Ethernet Commands 739 ProSafe M4100 and M7100 Managed Switches Note: Executing 'clear green-mode statistics' only clears the EEE T ransmit, Receive LPI event count, LPI duration, and Cumulative Energy Savings Estimates of the port. Other status parameters listed in above table will remain unaffected after 'clear green-mode stat[...]

Green Ethernet Commands 740 ProSafe M4100 and M7100 Managed Switches Cumulative Energy Saving (W * H)............. XX Time Since Counters Last Cleared............... 1 day 20 hr 47 min 34 sec show green-mode Use this command to display green-mode configuration for the whole system. The status is shown only for the modes supported on the correspondi[...]

Green Ethernet Commands 741 ProSafe M4100 and M7100 Managed Switches Example: The output of 'show green-mode <u/s/p>' is indicated below . (switch) #show green-mode Current Power Consumption (mW).............. XX Power Saving (%)............................ XX Cumulative Energy Saving /Stack (W * H)... XX Unit Green Ethernet Feature[...]

Green Ethernet Commands 742 ProSafe M4100 and M7100 Managed Switches Interface Energy-Detect Short-Reach-Config Short-Reach EEE Config Opr Auto Forced Opr Config --------- --------- --------- --------- --------- ----------- -------- 0/21 Disabled Inactive Disabled 0/22 Disabled Inactive Disabled 0/23 Disabled Inactive Disabled 0/24 Disabled Inactiv[...]

Green Ethernet Commands 743 ProSafe M4100 and M7100 Managed Switches show green-mode eee-lpi-history interface <slot/port> This command displays the interface green-mode EEE LPI history . Format show green-mode eee-lpi-history interface <slot / port> Mode T able 59. Example: (switch)#show green-mode eee-lpi-history interface 0/1 Samplin[...]

744 14 14. Co mmand L ist ip vrrp (Global Config) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 {deny | permit} (IP ACL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480 {deny | permit} (IPv6) . . . . . . . . . . . . [...]

Command List 745 ProSafe M4100 and M7100 Managed Switches area virtual-link authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269 area virtual-link dead-interval (OSPF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 area virtual-link dead-inter[...]

Command List 746 ProSafe M4100 and M7100 Managed Switches classofservice dot1p-mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444 classofservice ip-dscp-mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444 classofservice trust . . . . .[...]

Command List 747 ProSafe M4100 and M7100 Managed Switches clear traplog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 549 clear vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 549 cli[...]

Command List 748 ProSafe M4100 and M7100 Managed Switches debug spanning-tree bpdu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600 debug spanning-tree bpdu receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600 debug spanning-tree bpdu trans[...]

Command List 749 ProSafe M4100 and M7100 Managed Switches dos-control tcpoffset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 dos-control tcpport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 dos-control [...]

Command List 750 ProSafe M4100 and M7100 Managed Switches interface lag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 interface loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 interfa[...]

Command List 751 ProSafe M4100 and M7100 Managed Switches ip http secure-session soft-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 644 ip http server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640 ip http session[...]

Command List 752 ProSafe M4100 and M7100 Managed Switches ip pim join-prune-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 ip pim rp-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 ip pim rp-candi[...]

Command List 753 ProSafe M4100 and M7100 Managed Switches ipv6 mld-proxy unsolicit-rprt-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438 ipv6 mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362 ipv6 nd dad at[...]

Command List 754 ProSafe M4100 and M7100 Managed Switches lacp actor port priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 lacp actor system priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 10 lacp admin ke[...]

Command List 755 ProSafe M4100 and M7100 Managed Switches mac access-list extended rename . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474 mac address-table multicast forbidden-unregistered vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 mac address-table multicast forward-all vlan . .[...]

Command List 756 ProSafe M4100 and M7100 Managed Switches netbios-node-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 569 network (DHCP Pool Config) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 567 network area (OSPF) .[...]

Command List 757 ProSafe M4100 and M7100 Managed Switches passwords strength minimum lowercase-letters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655 passwords strength minimum numeric-characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656 passwords strength minimum special-characters . . . .[...]

Command List 758 ProSafe M4100 and M7100 Managed Switches protocol vlan group all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 quit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553 radi[...]

Command List 759 ProSafe M4100 and M7100 Managed Switches set gvrp adminmode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 set gvrp interfacemode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 set igmp . . . .[...]

Command List 760 ProSafe M4100 and M7100 Managed Switches show dampening interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310 show dhcp client vendor-id-option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 show dhcp l2relay agent-optio[...]

Command List 761 ProSafe M4100 and M7100 Managed Switches show ip dhcp global configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573 show ip dhcp pool configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573 show ip dhcp server statistics[...]

Command List 762 ProSafe M4100 and M7100 Managed Switches show ip pim bsr-router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 show ip pim interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 show ip pim neigh[...]

Command List 763 ProSafe M4100 and M7100 Managed Switches show ipv6 ospf range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 show ipv6 ospf stub table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 show ipv6 ospf virt[...]

Command List 764 ProSafe M4100 and M7100 Managed Switches show mac-address-table multicast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 show mac-address-table static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 show mac-address-table staticfi[...]

Command List 765 ProSafe M4100 and M7100 Managed Switches show running-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 show running-config interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531 show sdm prefer . . [...]

Command List 766 ProSafe M4100 and M7100 Managed Switches shutdown all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 snmp trap link-status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 677 snmp trap [...]

Command List 767 ProSafe M4100 and M7100 Managed Switches split-horizon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316 sshcon maxsessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637 sshcon timeou[...]

Command List 768 ProSafe M4100 and M7100 Managed Switches udld port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 619 udld reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 619 u[...]