NETGEAR PTV1000 manual

202-10591-01 January 2010 NETGEAR , Inc. 350 East Plumeria Drive San Jose, CA 95134 Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual[...]

ii v1.0, January 2010 © 2010 by NETGEAR, Inc. All rights reserved.. Technical Support Please refer to the support information card that shipped with your product. By registering your product at http://www.netgear.com/register , we can provide you with faster expert technical support and timely notices of product and software upgrades. NETGEAR, INC[...]

v1.0, January 2010 iii Regulatory Compliance Information This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the en[...]

v1.0, January 2010 iv • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party respo[...]

v v1.0, January 2010 Contents Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual About This Manual Conventions, Formats, and Scope ................................................................................... ix Revision History .......................................................................................................[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual vi v1.0, January 2010 Cords and Cables .................................................................................................... 2-1 On/Off Button ........................................................................................................... 2-2 Changing the TV I[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual vii v1.0, January 2010 Global Volume Control ........................................................................................... 2-12 Windows Audio Mixer ............................................................................................. 2-12 Changing the Sound using t[...]

ix v1.0, January 2010 About This Manual The NETGEAR ® Push 2 TV Adapter (PTV1000)/Intel® Wireless Display User Manual describes how to install, configure and troubleshoot the Push 2 TV Adapter (PTV1000)/Intel Wireless Display. The information in this manual is intended for readers with intermediate computer and Internet skills. Conventions, Forma[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual x v1.0, January 2010 For more information about network, Internet, firewall, and VPN technologies, see the links to the NETGEAR website in Appendix B, “Related Documents .” Note: Product updates are available on the NETGEAR, Inc. website at http://kbserver.netgear.com/products/PTV10[...]

1-1 v1.0, January 2010 Chapter 1 Connecting Intel Wireless Display allows consumers to use their HDTV as a huge, remote screen for their laptop. With Intel Wireless Display, consumers can connect their laptop to their TV and enjoy and share their personal media collections, latest YouTube videos, downloaded or streamed movies, music, or a variety o[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 1-2 v1.0, January 2010 Some laptops may have a button or key that starts Intel Wireless Display. This key will be located in different places depending on the brand of laptop. It is usually found on or around the keyboard. The key will contain a small version of the symbol below. Figure[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 1-3 v1.0, January 2010 Step 4: Scanning for Adapters After opening Intel Wireless Display (or after agreeing to the license), the application begins scanning for available adapters and the status reads Scanning for adapters . Figure 1-2 If the application does not automatically begin sc[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 1-4 v1.0, January 2010 • ID . If the default name has not been changed, use the ID to distinguish multiple entries and find your adapter. • Model . This is the adapter manufacturer and product model name. • Signal . The number of bars represents signal strength. The scale ranges f[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 1-5 v1.0, January 2010 First Time Connection Procedures This section continues from the end of Step 6 in the Using Intel Wireless Display section. Follow the steps below to complete the initial set up. Changing the TV Input Different TV brands have various methods of changing the TV inp[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 1-6 v1.0, January 2010 Step 1: Entering a Security Code When the Enter security code screen appears, type the security code shown on the TV. Figure 1-3 The security code numbers shown above are for example only! The numbers on your TV will be different. Type the numbers from your TV int[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 1-7 v1.0, January 2010 Step 2: Security Configuration Successful The Security configuration successful TV message indicates a correct security code entry. Step 3: Adapter is Connected After the laptop connects to the adapter, the TV shows Connected. Please wait . This message appears fo[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 1-8 v1.0, January 2010 Step 5: Finishing the Initial Set Up Process After the Connected. Please wait message disappears, the laptop screen and TV screen are the same. Congratulations! You have successfully completed the set up process! Click the Register link to register your adapter an[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 1-9 v1.0, January 2010 Exiting To exit Intel Wireless Display, click the Disconnect button, wait until the adapter disconnects, and click the Close Window button (red x) in the upper right corner of application window. If you click the Close Window button while still connected, you are [...]

2-1 v1.0, January 2010 Chapter 2 Troubleshooting Look through the Troubleshooting contents for a topic that comes closest to describing your problem. If you are unable to resolve the problem after reading through the Troubleshooting topics, search the FAQ topics. For additional help, visit http://kbserver.netgear.com/products/ PTV1000.asp. Initial [...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-2 v1.0, January 2010 white, and red). Connect each cord and cable into their correct inputs on the TV. (See your TV owner’s manual if needed.) Once plugged in, make sure the cords and cables are pushed all the way into their correct input positions. Using the composite video cable ([...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-3 v1.0, January 2010 • Sometimes the inputs are located beneath the regular channels on the TV. Try selecting the lowest TV channel and then go down one channel. Adapter Encountered a Problem on Startup The adapter is experiencing technical difficulties. First turn the adapter off a[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-4 v1.0, January 2010 • If you are not connected to a router change the wireless channel. Open Intel My WiFi Utility by clicking on the Intel My WiFi Technology icon in the taskbar and selecting Open Intel My WiFi Utility . Use the help document in Intel My WiFi Utility and search fo[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-5 v1.0, January 2010 3. Click the Scan for available adapters button on Intel Wireless Display. While scanning, the application automatically enables Intel My WiFi Technology and selects the correct security profile. Manually Setting the Correct Security Profile If the steps above do [...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-6 v1.0, January 2010 Firewall Issues Sometimes the laptop’s firewall will block the Wi-Fi connection between the laptop and the adapter. If this is the case, the laptop's firewall settings must be changed. The following instructions apply to a Microsoft Windows Firewall. To all[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-7 v1.0, January 2010 If the adapter will not turn on, or it is impossible to update the firmware, perform a factory reset. Reset Figure 2-3 Press and hold the Reset button while pushing the power button off and then on. Continue to hold the Reset button down until the adapter LED begi[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-8 v1.0, January 2010 2. Shut down the laptop, restart, open the application, scan for available adapters, and connect. 3. Reset the adapter, scan for available adapters, and connect. For help resetting the adapter, see “How do I Reset the Adapter?” on page 2-9 . 4. Check the lapto[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-9 v1.0, January 2010 How do I Change the Adapter Display Language To change the adapter display language, use the recessed button (7) while the adapter is on the ready screen shown. • A short press (less than half a second) will step forward through the languages. • A long press ([...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-10 v1.0, January 2010 How do I Clear the Adapter Memory? Clearing the adapter’s memory erases security settings and the user modified adapter name. This is helpful if you choose to sell your adapter, or if a neighbor came to your house and connected to your adapter, but now you do n[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-11 v1.0, January 2010 • Show the cursor . By default, Intel Wireless Display enables the cursor to be shown on the TV. To make the mouse cursor disappear on the TV, clear this check box. Resetting Intel Wireless Display will return the cursor to its default setting. • Automaticall[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-12 v1.0, January 2010 Global Volume Control Usually, the laptop’s sound is muted after connecting to Intel Wireless Display. Sometimes, however, other applications may automatically turn on the laptop’s sound. This will result in hearing the same sound from the laptop before heari[...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-13 v1.0, January 2010 To select which screens to use: 1. Simultaneously push the Windows button and the letter P on the keyboard. Select Duplicate in the popup window. If your laptop screen is not duplicated on your TV, proceed to the next step. 2. Click the Windows Start icon. 3. In [...]

Push 2 TV Adapter (PTV1000)/Intel Wireless Display User Manual 2-14 v1.0, January 2010 1. If the auto-connect adapter is discovered after initial launch, a connection attempt will be made 2. If the auto-connect adapter is already in the list when the application is relaunched including pressing the bezel button, a connection attempt will be made. I[...]

A-1 v1.0, January 2010 Appendix A Technical Specifications Feature Description Compatible laptops Intel Core i3, i5, or i7 processor Intel Graphics Media Accelerator HD graphics adapter Intel WiFi Link wireless networking adapter Microsoft Windows 7 operating system Intel Wireless Display software Network interface IEEE 802.11 b/g wireless Power 12[...]

B-1 v1.0, January 2010 Appendix B Related Documents This appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product. Document Link Windows XP and Vista Wireless Configuration Utilities http://documentation.netgear.com/reference/enu/winzerocfg/index.htm Internet N[...]