Oki FX-051 manual

Oki Data Corporation T okyo, Japan PRODUCT SPECIFICA TION FOR FX-051 F ACSIMILE TRANSCEIVER ISSUE 4 September , 1999[...]

Document Revision History T itle: FX-051 Product Specification Revision Revision Item Comments Change Number Date Author 1 Feb, ’98 ISSUE E3 Hanazawa 2 June, ’99 E3 Hanazawa Correction of page 2-4(item 18), 2-5(item 24), 2-8(item 8), 2-9(item 12), 2-10(item 19), 2-12(item 37), 2-14(item 45), 2-15(item 51), 3-2(item 3.9), 4-3(item 4.2.2), 4-20(i[...]

40672201TX Rev.4 i TABLE OF CONTENTS PRODUCT SPECIFICATION 1. SCOPE ...................................................................................................................... 1- 1 2. GENERAL DESCRIPTION ........................................................................................ 2-1 2.1 General Performance Specifications ...[...]

40672201TX Rev.4 ii 4.2.4 COPY ...................................................................................................................... ... 4-5 4.2.5 Select Function .......................................................................................................... 4 -5 4.2.6 Auto Dial ..........................................[...]

40672201TX Rev.4 iii 4.6.10 Broadcast entry report ............................................................................................... 4-47 4.6.11 Confidential RX report ............................................................................................... 4-48 4.6.12 Power OFF report ...........................................[...]

40672201TX Rev.4 iv 4.11 Reference for wordings between this series and current machines ......................... 4-58 5. DOCUMENT INPUT .................................................................................................. 5-1 5.1 Document Width ..........................................................................................[...]

40672201TX Rev.4 v 7.2.1 International NCU ...................................................................................................... 7-1 7.3 Communication Mode ................................................................................................ 7-1 7.4 Modem Operation ........................................................[...]

40672201TX Rev.4 vi 12. SHIPPING CONDITIONS .......................................................................................... 12-1 12.1 Vibration .................................................................................................................. .. 12-1 12.2 Drop Test .........................................................[...]

40672201TX Rev.4 1 - 1 1. SCOPE This package describes the FX-051 Facsimile Transceiver, which may be referred to as “the product” or “the machine” in this section. The product will be manufactured by Oki Data Corporation and distributed by ODA/OEL under an appropriate product name given by ODA/OEL upon agreement with Oki Data Corporation.[...]

40672201TX Rev.4 2 - 1 2. GENERAL DESCRIPTION The FX-051 is a half duplex, high performance, Facsimile Transceiver machine which communicates with distant stations over a voice level telephone line. The product can have a MFP (Multi-Function Peripheral) function as option (standard for ODA version) and use as "PC-scanner", "PC-printe[...]

40672201TX Rev.4 2 - 2 2.1 General Performance Specifications General performance specifications of the product are described below for a more thorough understanding of the following descriptions: 1) Style design Desktop design 2) Applicable network type PSTN (Public Switched Telephone Network), PBX telephone line. 3) Compatibility The product can [...]

40672201TX Rev.4 2 - 3 9) Printable length NA Letter: 273.4 mm (266.7 mm for assured quality) NA Legal: 349.6 mm (342.9 mm for assured quality) ISO A4: 291.0 mm (284.3 mm for assured quality) 10) Copy Stacker Copy stacker will have a capacity of 30* copies maximum. (Faceup stacking) * Note: Using the recommended paper 11) Printing paper Plain paper[...]

40672201TX Rev.4 2 - 4 13) Scanning method • 2592 bits contact image sensor. 14) Printing method 211.3 mm (2496 bits) and/or 216.7 mm (2560 bits) 15) Minimum scanning time NSS= 0, 5, 10 ms DCS= 0, 5, 10 ms 16) Minimum print time NSF= 0 ms DIS=10 milliseconds for 3.85 lines/mm. 5 milliseconds for 7.7 lines/mm. 17) Print speed Max. 8 sheets per min[...]

40672201TX Rev.4 2 - 5 20) Modem ITU-T V.29/V.27 ter./V.21 and V.17, V.33, as applicable. 21) Transmission speed 6 seconds (approx 6.9 sec) at 14.4 Kbps per sheet of ITU-T No.1 evaluation test chart, typical. Note 1: This speed denotes the time interval corresponding to Phase C (message transmission phase) as referred to in ITU-T T.30. 22) Protocol[...]

40672201TX Rev.4 2 - 6 28) MFP function By installing the optional software to PC, the following MFP function can be realized: • PC Printer function • PC Scanner function • PC FaxModem function • Location Programing function For details, see appendix A "MFP product specification" Note 1: This function is the standard for ODA. 29) [...]

40672201TX Rev.4 2 - 7 2.2 General Function Specifications General function specifications for the product are given below. They are summaries of whole descriptions. For convenience of description, the functions are classified in two categories: User functions and Service functions. 2.2.1 User functions 1) Transmissions Transmission is available by[...]

40672201TX Rev.4 2 - 8 6) Manual redial This feature is available to repeat dialing of the last called dial number. There is no limit on the number of repeat attempts. However, there are several restrictions in manual redial and feeder TX operation after restoration of power. After restoration of power, the machine can not return to the previous op[...]

40672201TX Rev.4 2 - 9 11) TSI/CSI 20 characters maximum are displayed. If the function is enabled, the received TSI is marked at the top of first reproduced copy. 12) Polling (TX & RX) Documents set on the A.D.F. or in the memory can be polled from a remote station. The machine can also receive documents from a remote station (RX). Note: Passw[...]

40672201TX Rev.4 2 - 10 19) Relay broadcast initiate This function automatically originates a message call via a relay station (which should be equipped with a Model OF27, OF38, OKIFAX-2600 or equivalent) to up to 99 locations. 20) Group dial list This function can store 5 lists. 21) Confidential message transmission This function transmits a Confi[...]

40672201TX Rev.4 2 - 11 27) Page re-transmission This feature is a part of the memory transmission feature that re-transmits in page units image information that is distorted to a certain extent during transmission. This feature is effective only for Memory Transmission mode. 28) Distinguishing text from pictures In half-tone scanning, half-tone im[...]

40672201TX Rev.4 2 - 12 32) Chain dialing This means consecutive dialing by using 2 or more One touch keys. 33) Realtime dialing The dialing digit signal can be transmitted immediately to the line when pressing the keypad, when dialing with telephone off-hook or Hook key is pressed. 34) Automatic pause signal insertion A pause signal can be inserte[...]

40672201TX Rev.4 2 - 13 39) TEL/FAX automatic switching (1) If the machine detects a call with a CNG signal indicating an auto send facsimile call, it starts an automatic document receiving operation. (2) If it detects a call without a CNG signal, it sounds the buzzer to indicate a telephone call. The calling person can hear a “ring back” tone [...]

40672201TX Rev.4 2 - 14 44) Key touch tone The key touch tone sounds when any key on the control panel is pressed. 45) Machine counter (Under planning) The machine has five counters to count DRUM, TONER, DRUMT and PRINT for printer section and SCAN for scanner section. Caution of “CHANGE DRUM” is displayed on LCD when the DRUM has reached the l[...]

40672201TX Rev.4 2 - 15 47) Broadcast entry report (confirmation purpose) For broadcast, each destination address and entry time etc. (immediate or delayed), is available for printing by manual control, only during programming prior to the communication. 48) Transmission error report The destination address, error status and total number of pages e[...]

40672201TX Rev.4 2 - 16 TYPE2 means ... The functions from #1 to #4 of upper TYPE2 are the same as TYPE1. If the FAX machine does not detect CNG signal during working of TAD, the machine will go to standby mode. TYPE3 means ... The functions from #1 to #2 of upper TYPE3 are the same as TYPE1. 3. The fax machine does not detect CNG signal during 15 [...]

40672201TX Rev.4 2 - 17 55) The following functions are not available. • 2nd cassette • Confidential broadcast • Relay broadcast • Delayed confidential transmission • Delayed relay broadcast initiate • Split transmission • Delayed mail box transmission • Secure poll TX • Battery backup (picture data) • FAX forwarding • No redu[...]

40672201TX Rev.4 2 - 18 2.2.2 Service functions 1) Local diagnosis (Refer to Fig. 4-1-1/2) Local diagnosis consists of a LED test, MF tone test, sensor test, H-MODEM TX/RX test, tone test and print test, including memorized test pattern printing, a memory check and a program version check. 2) RMCS (i) The remote diagnosis consists of at least by cu[...]

40672201TX Rev.4 3 - 1 3. PHYSICAL DESCRIPTION 3.1 General Appearance Overall design and mechanical structure of the product are shown in Fig. 3-1, 3-2. 3.2 Dimensions Overall dimensions of the product are less than the following: Width: Approx. 316 mm Depth: Approx. 383 mm Height: Approx. 190 mm 3.3 Weight The nominal weight of the product, exclud[...]

40672201TX Rev.4 3 - 2 3.8 Labels and Decals Some of the following Labels and Decals shall be pasted on the machine if necessary. • FCC Label Part 15 and Part 68 • Warning label on Power code • DOC certification • DOC LOAD NUMBER • BABT Approval Label • BABT REN Label • Warning Label for Fuser 3.9 Second Tray Second Tray is not availa[...]

40672201TX Rev.4 3 - 3 Table 3-1 OKI FX-051 Corporate Colors Parts Description Color Name Color Reference Enclosures Cover-Top Silver Gray OKI DATA Original 3.5Y8/0.5 Tray-Paper Ditto Ditto Cover - Front Ditto Ditto Cover - Main Ditto Ditto Cover - NCU Ditto Ditto Cover - Rear Ditto Ditto Tray - Document Ditto Ditto Other Parts Stacker Document Sil[...]

40672201TX Rev.4 3 - 4 Operator Panel Design (Alphabetalic Characters on Ten-key Pad) The specification is accordance with ITU (formely CCITT) recommendation, E.161. Some other countries will also introduce this specification for the approvals in near future. ABC DEF 123 GHI JKL MNO 456 PQRS TUV WXYZ 789 *0 # TONE OPER/UNIQUE[...]

40672201TX Rev.4 3 - 5 Fig. 3-1 FX-051 External View T ra y-P aper T ra y-Document Cov er-T op Case-OPE (T) Cov er-Main Cov er Manual Document Stack er-Document (Optional) Cov er-F ront 190 mm 383 mm 316 mm[...]

40672201TX Rev.4 3 - 6 MCNT PSU HV NCU Rear Right Front Left CN11 Centro CN10 NCU LED-Head CN12 CN9 Speaker DC OUTPUT CN7 PSU CN6 HV CN13 D-Motor CN2 Clutch CN1 S-Motor CN8 CB CN3 PC1/2 CN4 OPE CN5 CIS AC INPUT AC OUTPUT CB Fig. 3-2-1 Internal Configuration for FX-051[...]

40672201TX Rev.4 3 - 7 Document Paper EP drum Roller - Heater Paper exit ID unit LED head Scanner block Roller - ADF Separation rubber OPE board Roller - Scan Document exit Manual paper feeder inlet Image sensor Roller - Hopping Printer block Fig. 3-2-2 Internal Configuration for FX-051[...]

40672201TX Rev.4 3 - 8 Fig. 3-3 FX-051 Control Panel UNIQUE 8.5" A4 B5 A5 OKIFAX AUTO REC SEARCH AUTO DIAL HYPHEN REDIAL HOOK V.REQUEST PHOTO EX FINE FINE STD LIGHT NORMAL DARK ALARM STOP START YES NO OKI * 0 # ABC DEF JKL MNO GHI TUV WXYZ PQRS 7 8 9 4 5 6 1 2 3 SELECT FUNCTION DELAYED TX REPORT PRINT PRINT OPERATION COUNTER DISPLAY CONF.TX LO[...]

40672201TX Rev.4 4 - i INDEX Fig. 4-1 (1/2-2/2) General Key Operation (No Document) Fig. 4-1-1 (1/2-2/2) Typical Transmission Fig. 4-1-2 Typical Reception Fig. 4-2-1 Power on Operation Fig. 4-2-2 (1/2-2/2) FX-051 Mechanical Control Sequence Operation with Programming Fig. 4-3-1 One Touch Key Operation Fig. 4-3-2 Technical Programming Fig. 4-3-3 (1/[...]

40672201TX Rev.4 4 - ii Operations During Communication or Standby Fig. 4-4-1 Copy Operation Fig. 4-4-2 Message Confirmation Report Fig. 4-4-3 (1/3-3/3) AUTO REC Key Operation Fig. 4-4-4 Transmit Resolution and Type of Original Fig. 4-4-5 (1/3-3/3) LCD Message During Communication Fig. 4-4-6 (1/5-5/5) Calling Operation Fig. 4-4-7 Memory Cancel Fig.[...]

40672201TX Rev.4 4 - iii Fig. 4-5-8 Protocol Dump Report Fig. 4-5-9 Broadcast Entry Report Fig. 4-5-10 Broadcast Confirmation Report Fig. 4-5-11 Power Outage Report Fig. 4-5-12 Confidential RX Report Fig. 4-5-13 Call Back Message Fig. 4-5-14 Self Diagnosis FX-051 Tables Index Table 4-1 Multiple Function Combinations for Transmissions Table 4-2 Mult[...]

40672201TX Rev.4 4 - 1 4. OPERATION For operation, Table 4-1 to Table 4-9, Fig. 4-1 to Fig. 4-5 are attached at the end of this Section. 4.1 Major Apparatus Appearing on the Machine’s Cabinet Fig. 3-1, 3-3 and 3-4 shows the machine’s cabinet design for US/CANADA/INT’L versions. Fig. 3-2 and Fig.4-2-8 also shows a simple illustration of the Pa[...]

40672201TX Rev.4 4 - 2 4.1.6 Manual Paper Feeder A slot of the manual paper feeder is prepared underneath front face. 4.1.7 AC Inlet A male-type 3-pin connector to which the furnished AC power cord is connected. Note: The fuse for the mains is located within the power supply unit to prevent replacement by the user. When the fuse blows, a service pe[...]

40672201TX Rev.4 4 - 3 4.2 Controls and Indicators on Control Panel (Fig. 3-3) This Section identifies the locations of controls and indicators provided on Control Panel and explains their functions briefly. The detail of user and service functions are described in Section 4.4 “User Functions” and 4.5 “Technical Programming”. All the contro[...]

40672201TX Rev.4 4 - 4 PHOTO is applicable when the original document includes half-tone images and will cause the machine to send the image data in scale grades, using error diffusion algorithm. This key has an additional function. During an operation to select a function or to assign telephone numbers to auto dial codes, the operator can use this[...]

40672201TX Rev.4 4 - 5 4.2.4 COPY Function: This key is used for four purposes: document copying, transmission or commu- nication receipt output, location programming for one-touch or autodial and service person setting mode. When document is placed on ADF, the switch serves as a command key to direct the machine to start a copying operation. Press[...]

40672201TX Rev.4 4 - 6 4.2.6 Auto Dial Function: When pressed, will identify to the machine that the 2-digits code which follows is an auto-dial code registered in advance. A total of 70 locations numbered can be programmed. The operator can use AUTO DIAL with the external handset both on hook and off hook. Display: When pressed, a guidance message[...]

40672201TX Rev.4 4 - 7 Display: A message to indicate the redial state will show up on LCD display. 4.2.9 STOP Function: When STOP key is pressed twice within 3 seconds during message transmis- sion, the machine will immediately stop the operation. The half-fed document to the stacker will come to a halt. To remove the document, open the Control pa[...]

40672201TX Rev.4 4 - 8 4.2.10 START Function: When pressed, will cause the machine to start up for whatever the operator has commanded to the machine in advance - for example, message transmission, manual message reception, technical programming, etc. Display: When pressed, a message will appear on LCD display, which identifies the operation the ma[...]

40672201TX Rev.4 4 - 9 4.2.12 One-Touch Keys Function: One touch keys are used for following purposes. • single destination designation • various functions for communication or registration a) Single destination designation When used for single destination designation, pressing each key causes the origination of a call to preregistered destinat[...]

40672201TX Rev.4 4 - 10 4.2.14 V. REQUEST/HOOK Toggle selecting action between activation and deactivation of the voice request initiated by the operator. This function does not available in Instant dialing and memory reception. (Table 4-1) Function: this key has 2 functions. 1) Used as the hook-up/hook-down key while the optional or external tele-[...]

40672201TX Rev.4 4 - 11 Printer alarm (Printer I/F abnormal, engine error, fan alarm, and fusing unit error) cover open Recording paper jam or printer alarm shall be reset by opening the cover or by power off and on after remedying the cause. It is necessary to press the STOP switch in addition in case of a paper jam. Fig. 4-4-10 shows the LCD disp[...]

40672201TX Rev.4 4 - 12 4.3.1 Power Turning On It is assumed that the machine is unpacked and installed on a desk or appropriate stand. All default conditions (the machine configuration parameters) are assumed as those set at the factory, including AUTO RECEIVE MODE which is set to ON. a) Connect the socket end of the furnished power cord to the AC[...]

40672201TX Rev.4 4 - 13 Note 1: For convenience of description, the following assumptions are made for Fig. 4-1-1. 1) Five sheets of A4-size document be transmitted to an address, 3454 2111, which is placed in standby in Auto Receive Mode. The Date and Time indication is 14:59 FAX. 2) In One-touch Auto Dialing description, the telephone number, 345[...]

40672201TX Rev.4 4 - 14 6) Pressing the SEARCH key causes searching of the registered destinations (from among one-touch dial No. to 2-digits auto dial code). There are two following cases in this mode: • Manual search dial (the fifth flow from the bottom in Fig. 4-4-6) • Auto search dial (the fourth flow from the bottom in Fig. 4-4-6) In metho[...]

40672201TX Rev.4 4 - 15 In addition, LCD will display: 07/01/1998 14:57 TEL SELECT LOCATION which prompts the operator to enter the telephone number of the station to which the document is to be transmitted. b) Dialing Manual Dialing (Local Keypad) In this mode, the operator needs to tap all digits of the telephone number, 54456182, using the keypa[...]

40672201TX Rev.4 4 - 16 Manual Dialing (External Telephone) It is assumed that the operator dials the telephone number by using the dialing facility provided on the telephone unit. This operation is indicated by the rightmost in Fig. 4-1-1. Since the machine is not involved in this dialing operation, the message on the LCD will remain unchanged, th[...]

40672201TX Rev.4 4 - 17 Pressing the START key will cause the machine to seize the line and start dialing to the exchange. Fig. 4-4-6 shows AUTO START ON in parenthe- ses, which denotes that there is the case in which the operator does not need to press the START key when "AUTO START" is enabled. The message corresponds to " " s[...]

40672201TX Rev.4 4 - 18 Pressing the START key will cause the machine to seize the line and start dialing to the exchange. Similar to the case of One-Touch Auto Dialing, Fig. 4-4-6 shows AUTO START ON in parentheses, which denotes that there is the case in which the operator does not need to press START when "AUTO START" is enabled. OKI H[...]

40672201TX Rev.4 4 - 19 When the machine has completed dialing, the message on the LCD would change to: 001160977484184 CALLING The machine proceeds to send the message which is identified by the "KEYPAD DIAL" block shown in Fig. 4-1-1. Destination ID search dialing Any registered destination ID can be searched and direct dialing to the d[...]

40672201TX Rev.4 4 - 20 Ex. d) Reception of NSF (Personal ID)/CSI If the machine receives NSF (Non-Standard Facilities) with Personal ID from the distant station, the message on the LCD will be: OKI-TOKYO SENDING /144 OKI-T OKY O is receiv ed as P ersonal ID from the distant station. When the machine receives the CSI (Called Subscriber Identificati[...]

40672201TX Rev.4 4 - 21 If the machine receives no CSI and no NSF from the distant station, the message on LCD display will be: OKI-TOKYO SENDING /144 OKI-T OKY O is calling ID which is registered in One touch ke y . e) Transmission Starts After setting the document pages and storing the image data in the memory, the machine begins the handshaking [...]

40672201TX Rev.4 4 - 22 4.3.5 Typical Message Reception (Auto Receive and Manual Receive Modes) The product is shipped with its receive mode set to Auto Rec Mode. Therefore, when the power is turned on, the LCD indicates that the machine is in the auto-receive standby state. The operator can change the status by pressing the AUTOREC key. The select[...]

40672201TX Rev.4 4 - 23 sion, confidential transmission, relayed initiate transmission, feeder polling transmission, and transmission preparation) are described in Section 4.3. Refer to Fig. 4-1 (1/2 - 2/2 General Key Operation). 4.4.1 Method for Selection Function Press the FUNCTION key once to enter the mode for selecting the user functions. Pres[...]

40672201TX Rev.4 4 - 24 b) Data registration Data to be registered is classified into numeric data (ex. password, telephone num- ber, etc.) and character data (ex. calling party ID, personal ID, destination ID, etc.). Numeric data is input by using numeric (ten) keys and, if allowed, hyphen key, pause key (one touch No. 10) and space key (one-touch[...]

40672201TX Rev.4 4 - 25 4.4.4 Operation of Polling Reception Function: This feature is effective only when the distant station is ready for polling transmission. Operation: The operation of Polling Reception and Cancellation of Multiple Poll are shown in Fig. 4-3-11 and 4-4-6. 4.4.5 Selection of Reports and Lists The Report Print allows selecting 6[...]

40672201TX Rev.4 4 - 26 4.4.5.4 Phone Directory Function: The function allows the operator to print out the Phone Directory report manually. A brief description of "Phone Directory Report" will be given in Section 4.6 Reports and Lists. Operation: The operation is shown in Fig. 4-3-1 and 4-3-12. 4.4.5.5 Configuration Report Function: The [...]

40672201TX Rev.4 4 - 27 Operation: The operation is shown in Fig. 4-3-1 and 4-3-13. 4.4.6.2 Toner Counter Function: This counter is provided to serviceman to check the number of toner counter. When Technical Function No.32 (Toner counter clear)=OFF, this counter message is skipped. When Technical Function No.32 (Toner counter clear)=ON, this counte[...]

40672201TX Rev.4 4 - 28 3) Group dial programming (Fig. 4-3-16) 4) User function programming (Fig. 4-3-17) 5) Data programming (Fig. 4-3-19, 20, 21) 6) Personal BOX programming (Fig. 4-3-22) 7) MEM. password programming (Fig. 4-3-23) 8) Restrict ID programming (Fig. 4-3-24) Operation: The operation is shown in Fig. 4-3-1 and 4-3-14. Note: The machi[...]

40672201TX Rev.4 4 - 29 4.4.7.4 Function Programming Default table is shown in Table 4-6. Operation: The operation is shown in Fig. 4-3-1, 4-3-17 and 4-3-18. 01: Default arrangement for message confirmation report (Single location) (ON/OFF) Function: To enable or disable the automatic message confirmation printout after a single location call. Oper[...]

40672201TX Rev.4 4 - 30 Function: To enable H or L or disable the line monitory sound. In case setting H/L, monitor is enable for 5 seconds after dialing. Operation: The operation for setting of default position is described in Fig. 4-3-17 and 4-3-18. 07: Buzzer volume selection (LOW/MID/HIGH) Function: Selects the sound volume of each of the key t[...]

40672201TX Rev.4 4 - 31 11: Ringing response time selection (1 RING/05/10/15/20 SEC) This selection cannot be changed unless the service bit is set to one in some countries. Operation: The operation for setting of the default position is described in Fig. 4-3-17 and 4-3-18. 12: Distinctive Ring (OFF/ON/SET) Function: To select the ring pattern for [...]

40672201TX Rev.4 4 - 32 17: Memory TX/Feeder TX switch Function: To select the transmission mode (MEM. TX/FEED. TX) of default. This function becomes effective when Instant Dial of No. 26 is set to OFF. (Refer to P.4-20 Document reading timing) Operation: Refer to Fig. 4-3-18. 18: Default arrangement for power save mode (ON/OFF) Function: To enable[...]

40672201TX Rev.4 4 - 33 Function: To enable or disable MEM RX when toner low condition. ON: To receive the message in the memory when the remaining toner level is low or none. OFF: To print the message even the remaining toner level is low or none. 23: MEM full save Function: Broadcast transmission and other features originate calls after all the d[...]

40672201TX Rev.4 4 - 34 28: One-touch keys parameter Function: To assign the following features combined together as echo protection to each one-touch key. Protective tone Ignoring the 1ST DIS. Operation: The operation for setting of default position is described in Fig. 4-3-1 and 4-3-17 and 4-3-18. 4.4.7.5 Data programming Function: The kinds of d[...]

40672201TX Rev.4 4 - 35 a) Redial time (0 to 10 times: one time steps) b) Redial interval (1 to 6 minutes: one minute steps) c) Dial tone detection (ON/OFF) d) Busy tone detection (ON/OFF) e) MF or DP (MF/DP) f) DP rate (10/16/20 pps) g) DP make ratio (33%/39%) h) DP dial type (N/10-N/N+1) i) MF duration (75/85/100 ms) j) PBX Line (ON/OFF) k) Flash[...]

40672201TX Rev.4 4 - 36 4.4.7.8 Restrict ID programming Function: Restrict ID is a function available only person who knows Password, and this function can register 24 types of ID when Restrict Access of user's setting No. 26 is set to ON. Operation: The programming operations are described in Fig. 4-3-1 and Fig. 4-3-24. 4.4.7.9 Printer Counte[...]

40672201TX Rev.4 4 - 37 4.5 Technical Programming (Service Functions) Technical programming available with this product are classified into five categories, accord- ing to the nature and method of service functions: • Local test • Technical function • System reset • Default type set • PC-Loading For the flow of technical program of key op[...]

40672201TX Rev.4 4 - 38 4.5.2 Technical functions Parentheses means setting variation. Default table is shown in Table 4-7. Operation : The operation is shown in Fig. 4-3-4. 01. Service Bit (ON/OFF) Switching serviceman/user operation where there is a difference between U.S. and FTZ version, as in TSI/CSI registration for example. ON : Serviceman&a[...]

40672201TX Rev.4 4 - 39 TYPE2 : Real time dialing is available when the optional hand set is OFF-HOOK or press HOOK key. 08. TEL/FAX Switch (ON/OFF) Switching the TEL/FAX automatic switch function 09. MDY/DMY (MDY/DMY for US/CANADA version. MDY/DMY for INT'L version) Refer to Table 4-7. Switching LCD display and report print from month/day/yea[...]

40672201TX Rev.4 4 - 40 18. Error Criterion (00-99) To select the error criterion ratio. Refer to 4.8.13. 19. Off-Hook Bypass (ON/OFF) Switching the function of maintaining communication without hooking up the telephone set in usual test, etc. 20. Non-Loaded (NL) Equalizer (0, 1.8, 3.6, 7.2km) Determining the equalizing level of the receiving signa[...]

40672201TX Rev.4 4 - 41 30. NSF Switch (ON/OFF) NSF signal transmitting selectable. 31. ID/TSI Priority (ID/TSI) Selects ID/TSI printing in the distant station ID column of the report. 32. Toner Counter Clear (ON/OFF) Selects whether this function of toner counter clear operating is permitted for user or not. 33. Parallel Pickup (ON/OFF) Selects th[...]

40672201TX Rev.4 4 - 42 4.6 Reports and Lists This Section presents the formats of reports and lists referred in the preceding paragraphs, with some example entries for reference purposes. The formats are attached to the last of Section 4 for reference purposes (Fig. 4-5-1 to 4-5-13 for US/CANADA/INT'L version.) Brief descriptions for the item[...]

40672201TX Rev.4 4 - 43 13. Number of pages stored in memory Page number is printed only in case transmission from memory is carried out. 14. Page numbers of the pages to which an RTN signal or a PIN signal received. The asterisk (*) mark indicates that retransmission of the page met the criteria of copy quality. 4.6.2 Activity report Format : See [...]

40672201TX Rev.4 4 - 44 4.6.3 Broadcast confirmation report Format : See Fig. 4-5-10. Method : The report will be manually or automatically printed out. Descriptions : 1. Title of the report 2. Date and time when the report was printed 3. Sender ID 4. Total numbers of pages in particular communication 5. Specified transmission time (Time is not pri[...]

40672201TX Rev.4 4 - 45 4. Reception data • Prints the information of no paper/no toner reception. • ENTRIES is the number of received communication stored in the memory. • PAGES is the number of total pages of the received messages stored in the memory. 5. Personal Box • Prints the opend condition of personal Box. • MODE shows the type o[...]

40672201TX Rev.4 4 - 46 4. User programmed function parameters Function parameters are shown in sub-section 4.4.5.4. 5. Telephone and call back number 6. Dial parameters 4.6.6 Service default report (configuration report: service-bit = ON) Format : See Fig. 4-5-6. Method : The report will be manually printed out for maintenance purpose. Description[...]

40672201TX Rev.4 4 - 47 (2/2) 1. Title of the report 2. Date and time when the report was printed 3. Sender ID 4. Group number (#1 - #5) 5. Programmed one-touch numbers (01 - 10) 6. Programmed auto-dial numbers (01 - 70) 4.6.8 Protocol dump data printing Format : See Fig. 4-5-8. Purpose : To allow the serviceman to obtain a list of protocol signals[...]

40672201TX Rev.4 4 - 48 4.6.10 Broadcast entry report Format : See Fig. 4-5-9. Purpose : To allow the operator to obtain a list of entered locations for the broadcast. Descriptions : 1. Title of the report 2. Date and time when the report was printed 3. Sender ID 4. Session number 5. Specified transmission time 6. Reserved transmission address (One[...]

40672201TX Rev.4 4 - 49 4.6.13 Call back message Format : See Fig. 4-5-13. (Call back message) Purpose : To send a prepared message to destination. 4.7 Restrictions by the Printer 4.7.1 Printing time 8 pages of A4-size paper per minute As illustrated above, it takes about 7.5 seconds to print on a page of A4-size paper by the printer used in FX-051[...]

40672201TX Rev.4 4 - 50 4.7.2 Printing area and image scaling 4.7.2.1 Variable (reduction) printing FX-051 uses cut-sheet papers of A4, letter, and legal sizes. FX-051 (US), for example, reads a document at 8 dots/mm x 7.7 lines/mm and sends it to remote TX-051 (US). On the other hand, FX-051 (US) at receiving side receives the document, then conve[...]

40672201TX Rev.4 4 - 51 4.7.4 Heater control The temperature of the toner fixing heater is lowered in the standby state to reduce power consumption and heat generation. The heater control operation is shown below. • The printer is normally placed in the standby. If a call is received in this state, the heater is started; however, it takes a typic[...]

40672201TX Rev.4 4 - 52 4.8.2 Incoming Ringer Bell signal is generated by software for several countries (Holland, Belgium, New Zealand etc.) of INT'L version because ring circuit is not installed for the these countries. Therefore, the machine must make a bell signal and generate the bell sound through a speaker. Function : Machine will decid[...]

40672201TX Rev.4 4 - 53 4.8.7 Hyper power save mode (This wording is tentative) To decrease the machine's power consumption, machine supplies power only for Control Panel circuit and a part of NCU board circuit in standby mode. Refer to Fig.4-4-20 Machine shows *POWER SAVE MODE PRESS "START" during power save mode. Main power turned [...]

40672201TX Rev.4 4 - 54 To generate a cleaning page on the FX048 series, press the SELECT FUNCTION key once then press OT10 key and NO key twice. LCD display shows PRINTER CLEANING, then press YES key and PRINTER CLEANING EXECUTING is displayed. Machine will return to stand by mode after the cleaning procedure. Refer to Fig. 4-3-24 and Fig. 4-3-27.[...]

40672201TX Rev.4 4 - 55 4.8.15 T1(TX) and T1 (RX) Timer Value T1(TX) timer name is changed from T1 T.O. Refer to Fig.4-3-4-2/3 and Table 4-7. T1 (RX) timer is reception side. This setting is added to apply to PTT approval from this series. Refer to Fig.4-3-4-2/3 and Table 4-7. 4.8.16 T2 Timer Value T2 timer value means that EOL interval timer. This[...]

40672201TX Rev.4 4 - 56 4.9 New Functions and changed operations 4.9.1 300DPI function For FAX communication For Local copy and PC scan in horizontal resolution For Printer 4.9.1.1 TX mode When EXTRA FINE mode is selected, the machine will transmit in the following resolution. [Transmit resolution] [Remote RX machine’s ability] 300 x 300 DPI 300 [...]

40672201TX Rev.4 4 - 57 4.9.2 TX preparation and dual access For the patterns of Dual Access and the description of the Dual Access, refer to Table 4-5 Dual Access Combination Table and Fig. 4-4-16 TX Preparation and Dual Access. Reception is available during printing from the memory reception. Reception is available during scanning the document in[...]

40672201TX Rev.4 4 - 58 4.10.6 Personal BOX This function can set BOX No. (1 to 8) as Confidential reception/Bulletin Polling assigning. (Refer to 4.4.7.6, Fig. 4-3-22) 4.10.7 BULLETIN POLLING A kind of polling transmission. Bulletin polling enables polling transmission many times until deleting the documents stored in the memory. (Refer to Fig. 4-[...]

40672201TX Rev.4 4 - 59 Fig. 4-1-1/2 General Key Operation POWER ON 1 2 STANDBY MODE FUNCTION COPY SELECT FUNCTION COPY X 2 TECH. PROGRAMMING OT1 1 LOCAL TEST 1: SELF DIAGNOSIS 2: SENSOR CALIBRATION 3: LED TEST 4: TONE SEND TEST 5: MODEM SEND TEST 6: MODEM REC. TEST 7: MF (TONE) SEND TEST 8: TONE (TEL/FAX) TEST 2 TECH. FUNCTION 01: 02: 03: 04: 05: [...]

40672201TX Rev.4 4 - 60 Fig. 4-1-2/2 General Key Operation 1 2 USER PROGRAMMING OT9 FUNCTION 1 FUNC. PROGRAMMING 01: 02: 03: 04: 05: 06: 07: 08: 09: 10: 11: 12: 13: 14: 15: 16: 17: 18: 19: 20: 21: 22: 23: 24: 25: 26: 27: 28: MCF (SINGLE-LOC.) MCF (MULTI-LOC.) ERR.REPORT (MCF.) IMAGE IN MCF. SENDER ID MONITOR VOLUME BUZZER VOLUME CLOSED NETWORK TX M[...]

40672201TX Rev.4 4 - 61 Fig. 4-1-1-1/2 Typical Transmission XX:XX XXX (STANDBY CONDITION) AUTO DIALING? WHICH MODE? YES NO ONE-TOUCH • ONE-TOUCH KEY (e.g. No. 1) TWO-DIGIT AUTO DIAL CODE • PRESS "AUTO DIAL" KEY • SET THE CODE (e.g. 01) ( • LOAD DOCUMENT(S), SELECT RESOLUTION MODE) CED RECEIVED? NO YES 34542111 DIALING 34542111 CAL[...]

40672201TX Rev.4 4 - 62 CSI RECEIVED? 33454 2111 SENDING /144 NO YES OKI TAKASAKI SENDING /144 (¥ FAX MESSAGE TRANSMISSION STATUS) MESSAGE TRANSMISSION COMPLETED? RECEIVED DCN? NO YES LOCAL PROBLEM OCCURRED? RESULT = OK COMMUN. ERROR NO YES DOC. JAMMED , etc. COVER OPEN , or EXAMPLES NO XX:XX XXX (¥ ABOUT 1 SEC) ( ← STANDBY CONDITION) 1 Fig. 4-[...]

40672201TX Rev.4 4 - 63 XX:XX XXX AUTO RECEIVE MODE? YES NO MANUAL RECEIVE MODE 33454 2111 RECEIVING /144 OKI TAKASAKI RECEIVING /144 MESSAGE RECEPTION COMPLETED? RECEIVED DCN? NO YES LOCAL PROBLEM OCCURRED? RESULT = OK COMMUN. ERROR YES NO COVER OPEN EXAMPLES NO XX:XX XXX (¥ ABOUT 1 SEC) ( ← STANDBY CONDITION) ( ← STANDBY CONDITION) MANUAL RX[...]

40672201TX Rev.4 4 - 64 Fig. 4-2-1 Power on Operation POWER ON Powered on while holding down COPY key. Go to Technical Programming (Fig. 4-3-2) NO YES YES NO Initial system reset condition when power is turned ON. Powered on while holding FUNCTION key down Go to Fig. 4-3-18. or * Standby mode. * Note: T/F, FAX etc., are the last setting before powe[...]

40672201TX Rev.4 4 - 65 Fig. 4-2-2-1/2 FX-051 Mechanical Control Sequence (Single Page) • Separation rubber • S roller (includ feed, sensor and exit) • Exit pinch • CIS • PC2 • PC1 21.2 mm 29.5 mm 4.5 mm • ADF roller • First pinch roller ON: 15.7 mm (OFF: 6.9 mm) 15.5 mm Numerical numbers are theoretical values. [Scanner section ope[...]

40672201TX Rev.4 4 - 66 Fig. 4-2-2-2/2 FX-051 Mechanical Control Sequence (Multi Page) • Separation rubber • S roller (includ feed, sensor and exit) • Exit pinch • CIS • PC2 • PC1 21.2 mm 29.5 mm 4.5 mm • ADF roller • First pinch roller ON: 15.7 mm (OFF: 6.9 mm) 15.5 mm Numerical numbers are theoretical values. [Scanner section oper[...]

40672201TX Rev.4 4 - 67 Mode Restart Intial start Prefeed STD (3.85) FINE (7.7) EX. FINE (15.4) Holding Pulse speed Current value Pulse speed Current value Pulse speed Current value Pulse speed Current value Current value 600 PPS 428 mA 800 PPS 300 mA 800PPS 300 mA 400 PPS 268 mA 184 mA ----- ----- 800 PPS 428 mA 800PPS 268 mA 400 PPS 268 mA ----- [...]

40672201TX Rev.4 4 - 68 Fig. 4-3-1 One Touch Key Operation Note: OT2, OT6, 7, 8, 9, 10 are invalid during PC printing. 14:14 FAX ENTER ID → [XXXX] 14:14 FAX 07/01/1998 14:14 FAX SELECT LOCATION(S) (DOC. OFF/ON) Document on hopper DEPARTMENT No. registration DEPARTMENT No. no registration SELECT FUNCTION (OT) MEMORY AVAIL.= 100% ID OK ID NG FUNCTI[...]

40672201TX Rev.4 4 - 69 TECH. PROGRAMMING YES( ← /1-5) NO( → ) 14:14 FAX → key 1:LOCAL TEST YES( ← ) NO( → /1-5) ← key 1 1-5 → key 2:TECHNICAL FUNCTION YES( ← ) NO( → /1-5) 1-5 → key 3:SYSTEM RESET YES( ← ) NO( → /1-5) 1-5 → key 4:DEFAULT TYPE SET YES( ← ) NO( → /1-5) 5:PC-LOADING YES( ← ) NO( → /1-5) ARE YOU SURE [...]

40672201TX Rev.4 4 - 70 Fig. 4-3-3-1/3 Local Test 1:LOCAL TEST YES( ← ) NO( → /1-5) 1:SELF DIAGNOSIS YES( ← ) NO( → /1-8) ← key CPU PROG XXXX XXXX ← key 1:SELF DIAGNOSIS EXCUTING 1 (Display for 3 seconds) No paper, Cover open Paper jam, Printer alarm 2:SENSOR CALIBRATION YES( ← ) NO( → /1-8) 1-8 Go to stand by. → key → key or 1-[...]

40672201TX Rev.4 4 - 71 Fig. 4-3-3-2/3 Local Test (Sensor calibration) 1:SELF DIAGNOSIS YES( ← ) NO( → /1-8) 2:SENSOR CALIBRATION YES( ← ) NO( → /1-8) ← key 2:SENSOR CALIBRATION PLEASE SET DOCUMENT Set white document. 2:SENSOR CALIBRATION CALIBRATING OK RESULT=OK After 3 seconds SCANNING ERROR After 3 seconds NG & Press STOP key DOCUM[...]

40672201TX Rev.4 4 - 72 4:TONE SEND TEST YES( ← ) NO( → /1-8) 4:TONE SEND TEST 2100HZ SENDING ← key ← key or 1-8 4:TONE SEND TEST 1100HZ SENDING 4:TONE SEND TEST 1100HZ SENDING After 30 seconds elapsed *1) The LCD indication is further displayed more 30 seconds by pressing the START key. After 30 seconds elapsed After 5 seconds elapsed Indi[...]

40672201TX Rev.4 4 - 73 Fig. 4-3-4-1/3 Technical Function Programming ← key From Fig. 4-3-2 Technical Programming 1 → key or 1-5 FUNCTION NO. [_] ENTER 01-33 Go to Fig. 4-3-2. 01 01:SERVICE BIT [ OFF ]YES( ← ) NO( → ) ← key → key ON OFF 02 02:MONITOR CONT. [ OFF ]YES( ← ) NO( → ) ← key → key ON OFF 03 03:COUNTRY CODE [ GER ]YES([...]

40672201TX Rev.4 4 - 74 Fig. 4-3-4-2/3 Technical Function Programming 11:TONE FOR ECHO [ OFF ]YES( ← ) NO( → ) 12:MH ONLY [ OFF ]YES( ← ) NO( → ) → key ON OFF 13:H/MODEM RATE [14.4K]YES( ← ) NO( → ) → key 4.8K 9.6K 14.4K 14:T1(TX)TIMER VALUE [ 060 ]YES( ← ) NO( → ) → key 15:T1(RX)TIMER VALUE [ 035 ]YES( ← ) NO( → ) → key[...]

40672201TX Rev.4 4 - 75 Fig. 4-3-4-3/3 Technical Function Programming 22:T/F TONE ATT. [ 9 DB]YES( ← ) NO( → ) 23:MF ATT. [ 6 DB]YES( ← ) NO( → ) → key 0DB~15DB 24:RING DURA. * 10MS [ 14 ]YES( ← ) NO( → ) → key 25:CML TIMING *100MS [ 03 ]YES( ← ) NO( → ) → key 26:LED HEAD STROBE [01101]YES( ← ) NO( → ) → key 27:LED HEAD [...]

40672201TX Rev.4 4 - 76 Fig. 4-3-5 System Reset 3:SYSTEM RESET YES( ← ) NO( → /1-5) 1:ALL DATA CLR YES( ← ) NO( → /1-3) ← key 1-3 → key 2:LOCATION DATA CLR YES( ← ) NO( → /1-3) 1-3 3:CONFIG. DATA CLR YES( ← ) NO( → /1-3) 1-3 → key ← key 1 2 3 Go to Fig. 4-3-2. → key ← key ← key ARE YOU SURE ? YES( ← ) NO( → ) CLEAR[...]

40672201TX Rev.4 4 - 77 Fig. 4-3-6 Default Type Setting 4:DEFAULT TYPE SET YES( ← ) NO( → /1-5) DEFAULT TYPE SET [ 1]YES( ← ) NO( → ) ← key → key ← key 1~20 PROGRAMMING Change of version (default type) End of programming + 1 second (Flash memory writing) Change of default type Note: Even if serviceman makes all data clear by using sys[...]

40672201TX Rev.4 4 - 78 Fig. 4-3-7 Delayed TX SELECT FUNCTION (OT) MEMORY AVAIL.= 100% DELAYED TX TIME [_ : ]PRG. TIME 0-9 Press OT1 key. DELAYED TX TIME [1_: ]PRG. TIME 0-9 DELAYED TX TIME [12:_ ]PRG. TIME 0-9 DELAYED TX TIME [12:3_]PRG. TIME 0-9 DELAYED TX TIME [12:34]YES( ← ) NO( → ) SELECT LOCATION(S) Select location. Go to Calling operatio[...]

40672201TX Rev.4 4 - 79 Fig. 4-3-8-1/2 Personal Box Print Out PRINT PERSONAL BOX? YES( ← ) NO( → ) PERSONAL BOX NO. [ ] ENTER 0-8 SELECT FUNCTION [OT] MEMORY AVAIL.= 100% ← key ← key PERSONAL BOX NO. [1] YES( ← ) NO( → ) SELECT FUNCTION [OT] MEMORY AVAIL.= 100% PRG. PASSWARD [_ ] ENTER 4DIGITS Enter 1 → key PRESS OT2 Key Data in memor[...]

40672201TX Rev.4 4 - 80 Fig. 4-3-8-2/2 Memory Message Print Out SELECT FUNCTION (OT) MEMORY AVAIL.=50% MESSAGE IN MEMORY PRINTING STOPPED CANCEL ? YES( ← ) NO( → ) CONFIRM PAPER SIZE MEMORY CANCELED PRINT Personal BOX ? YES( ← ) NO( → ) NO DATA IN MEMORY Press OT2 key 3 sec Password No. registration Password No. no registration 1234 Press S[...]

40672201TX Rev.4 4 - 81 Fig. 4-3-9 Confidential TX Programming 14:14 FAX FUNC.NOT AVAILABLE NFS SWITCH=OFF Press FUNCTION key. 3 sec Press OT3 key. DIS BIT32=ON Press START key. Press START key. MAX 20 DIGITS (0~9, space, *, #) SELECT FUNCTION (OT) MEMORY AVAIL.=100% NO.=< MAIL BOX NO. > After 3 sec. NO.=_ ← key → key SELECT LOCATION Sele[...]

40672201TX Rev.4 4 - 82 SELECT FUNCTION (OT) MEMORY AVAIL.= 100% FUNC.NOT AVAIRAVLE Press OT4. OKI TOKYO YES(START) NO(LOC.) RELAY PASSWORD[0000] YES( ← ) NO( → ) Previous data of password, if assigned, is shown. RELAY PASSWORD[_ ] ENTER 4DIGITS RELAY PASSWORD[1_ ] ENTER 4DIGITS 1 RELAY PASSWORD[123_] ENTER 4DIGITS 23 RELAY PASSWORD[1234] YES( [...]

40672201TX Rev.4 4 - 83 Fig. 4-3-10-2/2 Relay Broadcast Initiate MEMORY AVAIL.= 100% SCANNING 01 07/01/1998 14:14 FAX COVER OPEN STOPPED MEMORY OVERFLOW 07/01/1998 14:14 FAX RELOAD DOCUMENT SEND SCANED PEGES? YES( ← ) NO( → ) LOAD DOCUMENT MEMORY OVERFLOW:FAX REFER TO USER GUIDE ← key → key Cover open *2 No document After 3 seconds elapsed [...]

40672201TX Rev.4 4 - 84 Fig. 4-3-11 Polling TX/RX Programming SELECT FUNCTION (OT) MEMORY AVAIL.= 100% BULLETIN POLL YES( ← ) NO( → ) PERSONAL BOX NO. [ ] ENTER 0-8 PERSONAL BOX NO. [2] YES( ← ) NO( → ) ILLEGAL OPERATION PROGRAMMING SEND SCANED PAGES? YES( ← ) NO( → ) OVER WRITE YES( ← ) NO( → ) MEMORY OVERFLOW:FAX REFER TO USER GUI[...]

40672201TX Rev.4 4 - 85 Fig. 4-3-12-1/2 Report Print (In case of Service bit = OFF) SELECT FUNCTION (OT) MEMORY AVAIL.= 100% 1:ACTIVITY REPORT YES( ← ) NO( → /1-6) → key ← key 1-6 ACTIVITY REPORT PRINTING CONFIRM PAPER SIZE No paper or cover open when the paper size is set to OTHER. No data in memory 1 1 2 2 2:BROADCAST MCF. YES( ← ) NO( [...]

40672201TX Rev.4 4 - 86 Fig. 4-3-12-2/2 Report Print (In case of Service bit = ON) SELECT FUNCTION (OT) MEMORY AVAIL.= 100% 1:ACTIVITY REPORT YES( ← ) NO( → /1-6) → key ← key 1-6 ACTIVITY REPORT PRINTING CONFIRM PAPER SIZE No paper or cover open when the paper size is set to OTHER. No data in memory 1 1 2 2 2:BROADCAST MCF. YES( ← ) NO( ?[...]

40672201TX Rev.4 4 - 87 Fig. 4-3-13-1/3 Counter Display/Clear (In case of Service bit = OFF&TOWER COUNT CLEAR=ON) 14:14 FAX SELECT FUNCTION (OT) MEMORY AVAIL.= 100% → key ← key ← key ← key Press FUNCTION key. DRUM COUNT CLEAR( ← ) NEXT( → ) ARE YOU SURE ? CLEAR( ← ) NEXT( → ) PRINT COUNT XXXXXX NEXT( → ) SCAN COUNT XXXXXX NEXT[...]

40672201TX Rev.4 4 - 88 Fig. 4-3-13-2/3 Counter Display/Clear (In case of service bit = OFF and Toner Counter Clear = OFF) 14:14 FAX SELECT FUNCTION (OT) MEMORY AVAIL.= 100% → key → key → key ← key ← key FUNCTION key. DRUM COUNT CLEAR( ← ) NEXT( → ) ARE YOU SURE ? YES( ← ) NO( → ) PRINT COUNT XXXXXX NEXT( → ) SCAN COUNT XXXXXX N[...]

40672201TX Rev.4 4 - 89 Fig. 4-3-13-3/3 Counter Display/Clear (In case of Service bit = ON) 14:14 FAX SELECT FUNCTION (OT) MEMORY AVAIL.= 100% → key ← key Press FUNCTION key. DRUM COUNT XXXXXX CLEAR( ← ) NEXT( → ) TONER COUNT XXXXXX CLEAR( ← ) NEXT( → ) SCAN COUNT XXXXXX CLEAR( ← ) NEXT( → ) CLEAR Press OT7 key. → key → key DRUM[...]

40672201TX Rev.4 4 - 90 Fig. 4-3-14 One Touch Programming SELECT FUNCTION (OT) MEMORY AVAIL.= 100% LOCATION PROGRAMMING ENTER(SRCH,OT,A/D,#) OT8 OT key NO=< FAX NO. > ID=< LOCATION ID. > After 3 seconds After 3 seconds NO=_ ID= 03 . . . . 123 NO=03 3404 7123_ ID= Press START key. NO=03 3404 7123 ID=_ 6 NO=03 3404 7123 ID=6 66 NO=03 3404[...]

40672201TX Rev.4 4 - 91 Fig. 4-3-15 Auto-dial Programmiong SELECT FUNCTION (OT) MEMORY AVAIL.= 100% LOCATION PROGRAMMING ENTER(SRCH,OT,A/D,#) OT8 Press A/D key. NO=< FAX NO. > ID=< LOCATION ID. > After 3 seconds ILLEGAL OPERATION After 3 seconds NO=_ ID= 03 . . . . 12 NO=03 3404 7123_ ID= Press START key. NO=03 3404 7123 ID=_ 666 NO=03 [...]

40672201TX Rev.4 4 - 92 Fig. 4-3-16 Group Dial Programming LOCATION PROGRAMMING ENTER(SRCH,OT,A/D,#) # GROUP SETTING [ ] ENTER 1-5 #05:SELECT LOC.(S) YES(STR/LOC) EXIT( → ) AUTO DIAL NO. [_ ] ENTER 01-70 SEARCH AUTO DIAL ENTER 1’st CHAR. OKI TAKASAKI CLEAR( ← ) EXIT( → ) OKI HONJYOU ENTER(STR) EXIT( → ) OKI HONJYOU CLEAR( ← ) EXIT( → [...]

40672201TX Rev.4 4 - 93 Fig. 4-3-17 User Function Programming Press OT9 key. key key Go to Function Programming. 1-9 key key Go to Dial Parameter Programming. 1-9 key key Go to Clock Adjustment.. 1-9 key key Go to System Data Programming. 1-9 1 2 3 4 (Fig. 4-3-18) (Fig. 4-3-19) (Fig. 4-3-20) (Fig. 4-3-21) key key Go to Personal Box Programming. 1-9[...]

40672201TX Rev.4 4 - 94 Fig. 4-3-18-1/4 Function Programming Function Programming 1:FUNC. PROGRAMMING YES( ← ) NO( → /1-7) 1 ← key → key FUNCTION NO. [_ ] ENTER 01-28 01 01:MCF(SINGLE-LOC.) [ OFF ] YES( ← ) NO( → ) ← key 01:MCF(SINGLE-LOC.) [ ON ] YES( ← ) NO( → ) ← key → key → key 02:MCF(MULTI-LOC.) [ OFF ] YES( ← ) NO( ?[...]

40672201TX Rev.4 4 - 95 Fig. 4-3-18-2/4 Function Programming Function Programming 09:TX MODE DEFAULT YES( ← ) NO( → ) ← key → key LED 10:T/F TIMER PRG. [20SEC] YES( ← ) NO( → ) ← key → key → key 20 SEC 35 SEC 13:1’ST PAPER SIZE [ A4 ] YES( ← ) NO( → ) ← key → key SET & ← key NO RI for 90 sec. 3 sec. passed 3 sec. p[...]

40672201TX Rev.4 4 - 96 Fig. 4-3-18-3/4 Function Programming Function Programming 17:MEM./FEEDER SW. [ MEM ] YES( ← ) NO( → ) ← key → key 18:POWER SAVE MODE [ ON ] YES( ← ) NO( → ) ← key → key 19:ECM FUNCTION [ ON ] YES( ← ) NO( → ) ← key → key 20:REMOTE DIAGNOSIS [ OFF ] YES( ← ) NO( → ) ← key → key 21:PC/FAX SWITCH[...]

40672201TX Rev.4 4 - 97 Function Programming OT key 25 26 27 28 ON OFF ← key ← key ← key ← key → key → key → key 1 4 ECHO PROTECTION [ OFF ] YES( ← ) NO( → ) FAX SPEED [14.4K] YES( ← ) NO( → ) 25:INSTANT DIALING [ ON ] YES( ← ) NO( → ) 28:ONE TOUCH PARAM. YES(OT) NO( → ) ON OFF 26:RESTRICT ACCESS [OFF] YES( ← ) NO( →[...]

40672201TX Rev.4 4 - 98 Fig. 4-3-19-1/4 Dial Parameters 1:FUNC. PROGRAMMING YES( ← ) NO( → /1-7) 2 2:DIAL PARAMETER YES( ← ) NO( → /1-7) ← key REDIAL TRIES [ 5TRY] YES( ← ) NO( → ) ← key → key 0 TRY REDIAL INTERVAL [1MIN] YES( ← ) NO( → ) ← key → key DIAL TONE DETECT [ OFF ] YES( ← ) NO( → ) ← key → key BUSY TONE D[...]

40672201TX Rev.4 4 - 99 Fig. 4-3-19-2/4 Dial Parameters PULSE DIAL TYPE [ N ] YES( ← ) NO( → ) ← key → key MF(TONE) DURATION [ 75MS] YES( ← ) NO( → ) ← key → key PBX LINE [ OFF ] YES( ← ) NO( → ) ← key → key OFF ON FLASH/EARTH/NORMAL [ N ] YES( ← ) NO( → ) ← key → key 2 AUTO START [ OFF ] YES( ← ) NO( → ) ← key[...]

40672201TX Rev.4 4 - 100 Fig. 4-3-19-3/4 Dial Parameters (1) Comparison List for all Versions TSI PROG. ★ ★ ★ ★ ★★★ ★★ ★ ★ ★ ★ COUNTRY CODE USA INT GBR IRL NOR SWE FIN DEN GER HUN TCH POL SUI AUT BEL SENDER ID ★ ★★ ★★ ★ ★★ ★★★ ★★★ FORWARDING NO. PRG. REDIAL TRIES ★★ ★ ★ REDIAL INTERVAL ?[...]

40672201TX Rev.4 4 - 101 Fig. 4-3-19-4/4 Dial Parameters (2) Comparison List for all Versions CLOCK ADJUSTMENT ★★ ★ ★ ★ ★ ★ COUNTRY CODE HOL POR ITA GRE AUS NZL SIN TSI PROG. ★★ ★ ★ ★ ★ ★ SENDER ID ★★ ★ ★ ★ ★ ★ FORWARDING NO. PRG. REDIAL TRIES ★ REDIAL INTERVAL ★ DIAL TONE DETECT BUSY TONE DETECT MF/DP [...]

40672201TX Rev.4 4 - 102 Fig. 4-3-20 Clock Adjustment 1:FUNC. PROGRAMMING YES( ← ) NO( → /1-7) 3 3:CLOCK ADJUSTMENT YES( ← ) NO( → /1-7) ← key [07/01/1998 12:23] YES( ← ) NO( → /0-9) ← key → key or 0-9 Enter time and date by using → key and 0-9 keys. → key or 1-7 Go to Fig. 4-3-17[...]

40672201TX Rev.4 4 - 103 Fig. 4-3-21 System Data Programming 4:SYSTEM DATA PRG. YES( ← ) NO( → /1-7) ← key 4 NO=_ ID= Press 03. SPACE ..123 keys. NO=03 3404 7123_ ID= Press START key. NO=03 3404 7123 ID=_ 666655...... NO=03 3404 7123 ID=OKI TOKYO_ Press START key. 1 NO=<CALL BACK NO.> After 3 seconds 1 NO=_ Press 03, SPACE..765 keys. 1 [...]

40672201TX Rev.4 4 - 104 Fig. 4-3-22 PERSONAL Box Programming 5:PERSONAL BOX PRG. YES( ← ) NO( → /1-7) ← key ← key PERSONAL BOX NO.[ ] ENTER 1-8 1 PERSONAL BOX NO.[1] YES( ← ) NO( → /) ILLEGAL OPERATION PRG. PASSWORD [_ ] ENTER 4 DIGITS Enter 1, 1, 1, 1 POLL Enter 1, 1, 1, 1 PRG. PASSWORD [XXXX] ENTER 4 DIGITS Confidential message alrea[...]

40672201TX Rev.4 4 - 105 Fig. 4-3-23 Memory Password Programming 6:MEM PASSWORD PRG. YES( ← ) NO( → 1-7) PRG. PASSWORD [ ] ENTER 4DIGITS PRG. PASSWORD [XXXX] ENTER 4DIGITS ILLEGAL OPERATION Go to Fig. 4-3-17 Call incoming form is MEM mode. Registered password 1111 1111 STOP key SPACE key 3 SEC PRG. PASSWORD [1111] YES( ← ) NO( → ) DELETE PA[...]

40672201TX Rev.4 4 - 106 Fig. 4-3-24 Restrict ID Programming ← key ← key ← key DEPARTMENT NO. [_ ] ENTER 01-24 01 *1) DEPARTMENT NO. [01] ENTER 01-24 No registration Registered (1234) ENTER ID [XXXX] ENTER 4DIGITS 123 8:RESTRICT ID PRG. YES( ← ) NO( → /1-9) → key → key → key or 1-9 Go to Fig. 4-3-17. ENTER ID [123X] ENTER 4DIGITS 4 [...]

40672201TX Rev.4 4 - 107 Fig. 4-3-25 Printer Cleaning Operation CONFIRM PAPER SIZE PRINTER CLEANING YES( ← ) NO( → ) After 3 seconds PRINTER CLEANING EXECUTING STOPPED SELECT FUNCTION(OT) MEMORY AVAIL.=50% Press STOP key. ← key → key Press OT10 key End of feed End of operation Go to stand by. Wrong paper size Cover open or paper jam or no p[...]

40672201TX Rev.4 4 - 108 4-4-1. Copy Operation Fig. 4-4-2 Message Confirmation Report 12:34 FAX No document on hopper Press COPY key. OKI TAKASAKI 12:34 OK 03 NO DATA IN MEMORY MSG.CONFIRMATION TO PRINT,PRESS"COPY" Confirmation report data No data After 3 seconds Press COPY key within 3 seconds. After 3 seconds After 3 seconds Press COPY [...]

40672201TX Rev.4 4 - 109 Fig. 4-4-3-1/3 AUTO REC Key Operation (When MEM.PASSWORD is not registered.) 4-4-3 AUTO REC Key Operation (When MEM.PASWORD is not registered.) 14:14 FAX Press AUTO REC. key. 14:14 FAX AUTO RECEIVE MODE Press AUTO REC. key. Press AUTO REC. key. TEL/FAX ON TEL/FAX OFF End of programming + 1 second (Flash memory writing) Pres[...]

40672201TX Rev.4 4 - 110 Fig. 4-4-3-2/3 AUTO REC Key Operation (Attached sheet 1) Attached sheet 1 MSG. IN MEMORY :MEM MSG. IN MEMORY :FAX AUTO RECEIVE MODE After 3 seconds elapsed After 3 seconds elapsed PROGRAMMING FLASH memory writing (1 to a few seconds) MSG. IN MEMORY :FAX After 3 seconds elapsed MSG. IN MEMORY PRINTING STOPPED Press STOP key.[...]

40672201TX Rev.4 4 - 111 4-4-3 AUTO REC Key Operation (When MEM.PASSWORD is registered.) Fig. 4-4-3-3/3 AUTO REC Key Operation (When MEM.PASSWORD is registered.) 14:14 FAX Press AUTO REC. key. 14:14 FAX AUTO RECEIVE MODE Press AUTO REC. key. Press AUTO REC. key. TEL/FAX ON TEL/FAX OFF End of programming + 1 second (Flash memory writing) *1) When ca[...]

40672201TX Rev.4 4 - 112 MSG. IN MEMORY :MEM MSG. IN MEMORY :MEM MEMORY RECEIVE MODE Press AUTO REC. key (within 3 seconds) PASSWORD is not registered yet. PASSWORD NG PASSWORD After 3 seconds elapsed PRG.PASSWORD [_ ] ENTER 4DIGITS Enter 1234 key. PRG.PASSWORD [1234] YES( ← ) NO( → ) ← key ← key MSG. IN MEMORY :FAX AUTO RECEIVE MODE PASSWO[...]

40672201TX Rev.4 4 - 113 Fig. 4-4-4 Transmit Resolution and Type of Original 4-4-4. Transmit Resolution and Type of Original 07/01/1998 14:14 FAX SELECT LOCATION(S) Press ← key. Transmit resolution 07/01/1998 14:14 FAX SELECT LOCATION(S) Press ← key. 07/01/1998 14:14 FAX SELECT LOCATION(S) Press ← key. 07/01/1998 14:14 FAX SELECT LOCATION(S) [...]

40672201TX Rev.4 4 - 114 Fig. 4-4-5-1/3 LCD Message During Communication (TX) LCD Indication During Transmission If characters of TSI/CSI are alphabets or others which are possible to display, machine shows it on the LCD. If the code is impossible to display, it is replaced by space. When all characters of TSI/CSI are spaces, machine OKI TOKYO DIAL[...]

40672201TX Rev.4 4 - 115 Fig. 4-4-5-2/3 LCD Message During Commuincation (RX) If characters of TSI/CSI are alphabets or others which are possible to display, machine shows it on the LCD. If the code is impossible to display, it is repalced by space. 14:14 T/F 14:14 FAX OKI SHIBAURA RECEIVING/ 144 03 3456 7890 RECEIVING/ 144 RI detection RI detectio[...]

40672201TX Rev.4 4 - 116 NO. = NO. =<MAIL BOX NO.> SELECT FUNCTION (OT) MEMORY AVAIL.= 100% 03 3456 7890 RECEIVING/144 OKI TOKYO RECEIVING/144 0P 03 3456 7890 RECEIVING/144 OKI SHIBAURA RECEIVING/144 PERSONAL ID REMOTE TEL NO. (TSI/CSI) DISTANT ID (Polling reception) DIAL NO. (Polling reception) If characters of TSI/CSI are alphabets or other[...]

40672201TX Rev.4 4 - 117 Fig. 4-4-6-1/5 Calling Operation (FAX) *1) *2) Except transmission preparation and dual access. Display shows during XTWAIT or 3 seconds or DT detetion time. Lower 20 digits are displayed when over 20 digits are entered by numeric key. Upper 20 digits are displayed when SEARCH key is pressed. Document mark is displayed when[...]

40672201TX Rev.4 4 - 118 Fig. 4-4-6-2/5 Calling Operation (FAX) GROUP SETTING [_ ] ENTER 1-5 MULTI LOCATION 01 02 *01 1234 Press # key. No registration 05 02 3SEC T.O 1_ 1234567_ ENTRY IS OK? DIAL(START)CHECK( → ) *2) TEN "1" 234567 NOT PROGRAMMED CHECK Press START key or 5SEC T.O LOC Press START key or 5SEC T.O LOC Press START key or 5[...]

40672201TX Rev.4 4 - 119 Fig. 4-4-6-3/5 Calling Operation (FAX) CHECK LPCATION(S) YES(STR/LOC) EXIT( → ) OKI TOKYO CLR(STR)EXIT(LOC./ → ) Press OT key. Press → key Next Loc Next Loc End of Loc End of Loc Press START key Press → key START Press A/D key. Press SEARCH key. TEN key + Press START key. Registed START → LOC START → LOC START ?[...]

40672201TX Rev.4 4 - 120 Fig. 4-4-6-4/5 Calling Operation (FAX) Display shows during XTWAIT or 3 seconds or DT detection time. POLLING RX SELECT LOCATION OKI TAKASAKI YES(START) NO(LOC.) 0273 56 7890 DIALING Press OT key. Start of dialing AUTO DIAL NO. [ ] ENTER 01-70 OR GROUP OKI HONJYOU YES(START) NO(LOC.) 0495 22 2111 DIALING Press A/D key. Pres[...]

40672201TX Rev.4 4 - 121 Fig. 4-4-6-5/5 Calling Operation (TEL) *1) *2) Hook key is invalid when REAL DIAL = OFF or TYPE1. Display shows during XTWAIT or 3 seconds or DT detection time. 14:14 TEL OKI TAKASAKI YES(START) NO(LOC.) 0273 56 7890 DIALING Press OT key. Start of dialing 3SEC T.O OR START key 3SEC T.O OR START key 3SEC T.O OR START key 3SE[...]

40672201TX Rev.4 4 - 122 Fig. 4-4-7 Memory Cancel 14:14 FAX TX TIME → 04/26 14:14 Press STOP key. COMMUNICATION CANCEL YES( ← ) NO( → ) ← key → key OKI TAKASAKI CANCEL( ← ) OTHER( → ) ← key → key CANCELED After 3 seconds 03 3456 7890 CANCEL( ← ) OTHER( → ) ← key → key CANCELED After 3 seconds *2: When other communication i[...]

40672201TX Rev.4 4 - 123 Fig. 4-4-8 Stop Operation 07/01/1998 14:14 TEL SELECT LOCATION(S) Press STOP key. Stand by with document DOCUMENT REMOVAL Press STOP key. 07/01/1998 14:14 FAX RELOAD DOCUMENT OKI TOKYO SENDING / 144 Press STOP key twice. STOPPED After 5 seconds 14:14 FAX Document on hopper Note: STOP key operation is invalid during RX mode,[...]

40672201TX Rev.4 4 - 124 Fig. 4-4-9 Voice Request OKI TOKYO SENDING / 144 PIP (PIN) received. Voice request from local station LIFT HANDSET, AND PRESS VOICE REQUEST OKI TOKYO RECEIVING/ 144 PRI-Q reception LIFT HANDSET, AND PRESS VOICE REQUEST OKI TOKYO SENDING / 144 Press V/R key. Voice request to local station VOICE REQ. ACTIVATED SENDING / 144 O[...]

40672201TX Rev.4 4 - 125 Fig. 4-4-10 Alarm State and Receive into Memory PAPER OUT/JAM :FAX CHECK PAPER OR PATH Paper JAM 14:14 FAX REPLACE TONER CART. No toner *2 PRINTER ALARM 3:TEL REFER TO USER GUIDE Fan alarm 07/25/1998 14:14 FAX RELOAD DOCUMENT Pre-feed error 14:14 FAX COVER OPEN Cover open 14:14 FAX CHANGE DRUM SOON Image drum alarm MSG.IN M[...]

40672201TX Rev.4 4 - 126 Fig. 4-4-11 TEL/FAX AUTO SW Reception 14:14 T/F Ring detection AUTO REC. START LIFT HANDSET MANUAL RX START 14:14 TEL Press START key. OKI TOKYO RECEIVING/ 144 20 or 35 seconds CNG detection Without CNG detection Hook up. TIME OUT 20 or 35 seconds (CML ON) Press STOP key. Go to stand by. OFF HOOK and Remote receive are OK w[...]

40672201TX Rev.4 4 - 127 Fig. 4-4-12 TAD Interface 14:14 TAD Ring detection (T/F timer) Time out 20 or 35 seconds 14:14 TAD TELEPHONE BUSY CNG detection or end of TAD operation at TYPE1/TAD TAD setting: TYPE 3 and 30-sec or less recording time. 14:14 TAD AUTO REC. START OKI TOKYO RECEIVING/144 Go to FAX receive mode. Remote reception is OK. End of [...]

40672201TX Rev.4 4 - 128 Fig. 4-4-13 Print Out from Memory by Replace Paper MSG. IN MEMORY:FAX CONFIRM AND "STOP" Press STOP key or Message Print Operation after paper replacement. MSG. IN MEMORY PRINTING Press STOP key. STOPPED End of paper feed out (one page) CANCEL ? YES( ← ) NO( → ) ← key (Cancel) → key MEMORY CANCELED After 3[...]

40672201TX Rev.4 4 - 129 Fig. 4-4-14-1/2 Print Out from Memory (Memory Only Reception) (When MEM. PASSWORD is not registered.) Press AUTO REC. key. Press STOP key. End of feed key (Cancellation) key After 3 seconds elapsed Go to stand by mode. The machine enables the manual printout of MSG. IN MEMORY data by using print operation (F key + OT2). Fee[...]

40672201TX Rev.4 4 - 130 Fig. 4-4-14-2/2 Print Out from Memory (Memory Only Reception) (When MEM. PASSWORD is registered.) MSG. IN MEMORY :MEM Press AUTO REC. key. PROGRAMMING PASSWORD ERROR Press STOP key. STOPPED End of feed CANCEL ? YES( ← ) NO( → ) ← key (Cancel) → key ← key (Cancel) → key MEMORY CANCELED After 3 seconds elapsed Go [...]

40672201TX Rev.4 4 - 131 Fig. 4-4-15 Power OFF Report POWER ON POWER OUTAGE REPORT PRINTING 14:14 FAX Detect message memory data lost End of printing[...]

40672201TX Rev.4 4 - 132 Fig. 4-4-16 TX Preparation and Dual Access OKI TOKYO SENDING / 144 OKI TOKYO RECEIVING/ 144 OKI TOKYO MEMORY-RX/ 144 Set documents. Set documents. SELECT LOCATION RELOAD DOCUMENT OKI TAKASAKI YES(START) NO(LOC.) SELECT FUNCTION (OT) MEMORY AVAIL.= 090% Set documents during memory TX or set documents during feeder TX after t[...]

40672201TX Rev.4 4 - 133 Fig. 4-4-17 PC Mode Transmission and Reception 14:14 PC RX command received from PC. Connect line PC mode reception PC FAX RECEIVING End of communication 14:14 PC *1 14:14 FAX TX command received from PC. Connect line PC mode transmission PC FAX SENDING End of communication 14:14 FAX *1 *1: Page numbers for the remote stati[...]

40672201TX Rev.4 4 - 134 Fig. 4-4-18 Local Printer and Scanner Operations for PC Mode 07/01/1998 14:14 FAX SELECT LOCATION(S) Scan command receive from PC. Press START key. Local scanner mode for PC SCANNING TO PC End of communication 14:14 FAX 14:14 FAX Print command receive from PC. (Printer subsystem = session mode) Local printer mode for PC PRI[...]

40672201TX Rev.4 4 - 135 Fig. 4-4-19 Flash Memory Write Operation Write Operation of Flash Memory 1) Write operation of flash memory is excuted for location registration, user programming, service- man setting when the data is entered or changed. • When the FUNCTION key or STOP key is pressed to return to stand by state, flash memory is written w[...]

40672201TX Rev.4 4 - 136 Fig. 4-4-20 Power Save Mode *1) Machine automatically move to Power Save Mode when following conditions are all satisfied. (1) Power Save Mode = ON (User setting) (2) Stand by condition without document and alarm (3) No image data in memory (4) On Hook (5) Machine detects power off timer (180 seconds) after above (1) to (4)[...]

40672201TX Rev.4 4 - 137 Fig. 4-4-21-1/2 Location Programming (OT/Auto Dial) LOCATION PROGRAMMING ENTER(SRCH,OT,A/D,#) OT8 SELECT FUNCTION (OT) MEMORY AVAIL. = 100% ONE TOUCH NO. [01] YES( ← ) NO( → /SRCH) Press SEARCH key. NO=< FAX NO. > ID=< LOCATION ID. > After 3 seconds or press ← key. *1 *2 Press STOP or → key. NO=_ ID= NO=[...]

40672201TX Rev.4 4 - 138 Fig. 4-4-21-2/2 Location Programming (OT/Auto Dial) during Normal Dial Operation 1234_ 07/25/1998 10:00 T/F SELECT LOCATION(S) ONE TOUCH NO. [01] YES( ← ) NO( → /SRCH) After 3 seconds or press ← key. NO=1234 ID=_ NO=1234 ID=NEW YORK OFFICE NO=< OR LOCATION > NO=_ NO=03 3404 7345 PROGRAMMING 666 . . . . . Press S[...]

40672201TX Rev.4 4 - 139 Fig. 4-4-22-1/2 Chain Dial (Before Dialing) In case of the following locations were registered in One-touch keys Press OT1 key. Press SEARCH. 6 MEM./FEEDERR SW. = FEED. OT1: OT2: OT3: TEL number is 001+ and ID is VIA NCC. TEL numbers is 234+ and ID is WORLD CORP. TEL number is *567 and ID is MR.OKI. 8 Waiting Press OT2 key.[...]

40672201TX Rev.4 4 - 140 Fig. 4-4-22-2/2 Chain Dial (After Dialing) In case of the following locations were registered in One-touch keys OT1: OT2: OT3: TEL number is 03 3940 6000 and ID is OKIFAX SERVICE. TEL number is *313045# and ID is BOX NO. TEL number is 0002# and ID is PASSWORD NO. Waiting Press OT2 key. OT2 (AUTO START = OFF) Press START key[...]

40672201TX Rev.4 4 - 141 14:14 FAX ENTER ID → [XXXX] Enter 1234 3 SEC T.O ID OK No document Document ID NG 14:14 FAX ENTER ID → [1234] INVALID ID 14:14 FAX 07/01/1998 14:14 FAX SELECT LOCATION(S) Fig. 4-4-23 RESTRICT ACCESS[...]

40672201TX Rev.4 4 - 142 Fig. 4-4-24 Instant Dialing Operation 07/01/1998 14:14 T/F SELECT LOCATION(S) OT OKI TAKASAKI DIALING Start of dialing During dialing End of scanning 0273 56 7890 DIALING 0273 56 7890 CALLING End of dialing BT (Busy tone) detection BT (Busy Tone) undetection MEMORY AVAIL.=50% SCANNING 03 07/01/1998 14:20 T/F REDIAL → 07/0[...]

40672201TX Rev.4 4 - 143 MESSAGE CONFIRMA TION 07/01/1998 08:05 ID=OKI DATE S,R-TIME DISTANT STATION ID MODE PAGES RESULT 07/01 00'20" OKI FAX CALLING 02 OK 0000 Fig. 4-5-1 Message Confirmation Report (MCF)[...]

40672201TX Rev.4 4 - 144 MESSAGE CONFIRMA TION 07/01/1998 17:05 ID=OKI DATE S,R-TIME DISTANT STATION ID MODE PAGES RESULT 07/01 00'20" B.C. 01 COMP. 60A0 Fig. 4-5-2 IMAGE in MCF with Memory TX 150 km[...]

40672201TX Rev.4 4 - 145 ACTIVITY REPORT 07/01/1998 17:05 ID=OKI TOTAL TIME CALLING=08:22' CALLED=17:30' DATE TIME S,R-TIME DISTANT STATION ID MODE PAGES RESULT 06/29 10:00 01'20" OKI FAX CALLING 02 OK 0000 06/29 10:10 01'00" 0485 88 3385 CALLING 00 STOP 9080 06/29 10:30 00'20" ODS TAKASAKI CALLING 00 NO 90C1[...]

40672201TX Rev.4 4 - 146 ACTIVE MEMOR Y FILES 07/01/1998 17:05 ID=ODC RECEPTION ENTRIES PAGES 05 20 PERSONAL BOX BOX NO. MODE ENTRIES PAGES 01 CONF 03 20 02 CONF 01 02 05 POLL 01 05 POLLING TX/RX DATE TIME DISTANT STATION ID MODE PAGES POLLED 03 03/19 12:05 OKI POLLING TRANSMISSION DATE TIME DIDTANT STATION ID MODE PAGES 03/20 20:00 OKI DATA SYSTEM[...]

40672201TX Rev.4 4 - 147 CONFIGURA TION 07/01/1998 17:05 ID=OKI FUNCTION LIST 01:MCF (SINGLE-LOC.) 02:MCF (MULTI-LOC.) 03:ERR.REPORT (MCF) ON ON ON 04:IMAGE IN MCF 05:SENDER ID. 06:MONITOR VOLUME ON ON LOW 07:BUZZER VOLUME 08:CLOSED NETWORK 09:TX MODE DEFAULT MIDDLE OFF FINE/NORMAL 10:T/F TIMER PRG. 11:RING RESPONSE 12: DISTINCTIVE RING 35SEC 1RING[...]

40672201TX Rev.4 4 - 148 Fig. 4-5-6 Service Default Report (Configuration Report: Service bit=ON) CONFIGURA TION 07/01/1998 17:05 ID=OKI FUNCTION LIST 01:SERVICE BIT 02:MONITOR CONT. 03:COUNTRY CODE ON OFF USA 04:TIME/DATE PRINT 05:TSI PRINT 06:TAD MODE OFF ON TYPE2 07:REAL TIME DIAL 08:TEL/FAX SWITCH 09:MDY/DMY. TYPE2 ON MDY 10:LONG DOC. SCAN 11:T[...]

40672201TX Rev.4 4 - 149 TELEPHONE DIRECT OR Y P1 07/01/1998 17:05 ID=OKI LOCATION ID TEL NO. PRM. ECHO RETE ONE TOUCH 1 OT1 OKI OFFICE 0001 123 123 123 (ON) (14.4) OR 0101 111 222 333 2 OT2 OKI LABORATORY 0002 456 456 456 (OFF) (14.4) OR 0102 444 555 666 3 OT3 ODC TAKASAKI 0003 789 789 789 (ON) (14.4) OR 0103 777 888 999 4 OT4 ODC QA/QC LAB. 0004 [...]

40672201TX Rev.4 4 - 150 TELEPHONE DIRECT OR Y P2 07/01/1998 17:05 ID=OKI LOCATION ID TEL NO. AUTO DIAL 45 AD45 1045 46 AD46 1046 47 AD47 1047 48 AD48 1048 49 AD49 1049 50 AD50 1050 51 AD51 1051 52 AD52 1052 53 AD53 1053 54 AD54 1054 55 AD55 1055 56 AD56 1056 57 AD57 1057 58 AD58 1058 59 AD59 1059 60 AD60 1060 61 AD61 1061 62 AD62 1062 63 AD63 1063[...]

40672201TX Rev.4 4 - 151 TELEPHONE DIRECT OR Y P3 07/01/1998 17:05 ID=OKI GROUP_NUMBER_=_#1_#2_#3_#4_#5 #1_ONE_TOUCH 1 2 3 4 5 6 7 8 9 10 AUTO DIAL 01 02 03 04 05 06 07 ••••••• 26 27 28 29 30 31 32 ••••••• #2_ONE_TOUCH AUTO DIAL #3_ONE_TOUCH AUTO DIAL #4_ONE_TOUCH AUTO DIAL #5_ONE_TOUCH AUTO DIAL Fig. 4-5-7-3 Telephone D[...]

40672201TX Rev.4 4 - 152 PROT OCOL DUMP 07/01/1998 19:00 ID=OKI TAKASAKI DATE TIME S,R-TIME DISTANT STATION ID MODE PAGES RESULT 04/19 14:49 *01'33" OKI SHIBAURA(6412) CALLING 01 OK 0000 FCF TX TSI DCS PPS EOP DCN RX NSF CSI DIS CFR MCF TX RX TX RX TX DIS DTC 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 DCS 00 00 00 00 00 00 00 0[...]

40672201TX Rev.4 4 - 153 BROADCAST ENTRY REPORT 07/01/1998 17:05 ID=OKI LOCATION ID LOCATION ID LOCATION ID ONE TOUCH 1 = OT1 2 = OT2 3 = OT3 4 = OT4 5 = OT5 6 = OT6 7 = OT7 8 = OT8 9 = OT9 10 = OT10 AUTO DIAL 01 = AD1 02 = AD2 03 = AD3 04 = AD4 05 = AD5 06 = AD6 07 = AD7 08 = AD8 09 = AD9 10 = AD10 11 = AD11 12 = AD12 13 = AD13 14 = AD14 15 = AD15[...]

40672201TX Rev.4 4 - 154 BROADCAST CONFIRMA TION REPORT 07/01/1998 17:05 ID=OKI PAGES = 01 START TIME = 07/01 17:02 TOTAL TIME = 00:02'30" LOCATION ID PAGES RESULT LOCATION ID PAGES RESULT ONE TOUCH 1 = HEAD OFFICE 01 OK 2 = OT2 01 OK 3 = OT3 01 OK 4 = OT4 01 OK 5 = OT5 01 OK AUTO DIAL 01 = AD1 01 OK 02 = AD2 01 OK 03 = AD3 01 OK 04 = GER[...]

40672201TX Rev.4 4 - 155 POWER OUT AGE REPORT 07/01/1998 17:05 ID=OKI DATE TIME S,R-TIME DISTANT STATION ID MODE PAGES RESULT 06/30 10:10 0485-88-3385 LOST 9080 06/30 10:30 ODS TAKASAKI 03 LOST 0000 06/30 12:05 01'20" OKI FAX CONF=01 03 LOST 0000 06/30 13:00 00'20" 03-5476-4300 CALLED 01 LOST 0000 06/30 10:50 01'20" 04[...]

40672201TX Rev.4 4 - 156 CONFIDENTIAL RX REPORT 07/01/1998 17:05 ID=OKI DATE TIME S,R-TIME DISTANT STATION ID MODE PAGES RESULT 07/01 00:20 00'00" OKI FAX CONF=01 02 OK 0000 Fig. 4-5-12 Confidential RX Report[...]

40672201TX Rev.4 4 - 157 Fig. 4-5-13 Call Back Message 07/01/1998 09:24 OKI SHIBAURA → OKI HONJO NO.002 PLEASE CALL BACK OKI SHIBAURA 1 03 5476 1234[...]

40672201TX Rev.4 4 - 158 CPU-ROM VERSION AA00 HASH OK DACD CPU-RAM OK PROGRAM VERSION AA00 HASH OK 3142 LANGUAGE VERSION LL10 HASH OK 3F06 DEFAULT VERSION DD10 HASH OK A683 *1 RAM1 2.5M OK *2 RAM2 OK DEFAULT TYPE 01 07/01/1998 10:30 *1 marked item is shown for condition of all RAM except EXCEED RAM. *2 marked item is shown to SRAM for EXCEED. Fig. [...]

40672201TX Rev.4 4 - 159 Table 4-1 Multiple Function Combinations for Transmissions Single Loc. TX Broadcast TX Delayed TX Confidential TX Relay Broadcast Initiate Manual TX Chain Dialing Automatic Alternate Selecting Call Closed User Group Page Retransmit Redial if Communication Error in Memory TX Sender ID Voice Request (Initiate) Voice Request ([...]

40672201TX Rev.4 4 - 160 Table 4-2 Multiple Function Combinations for Reception In-between Memory Reception Memory Reception Memory Only Reception Confidential Reception Closed Network TSI Print TIME/DATE Print Voice Request (Initiate) Voice Request (Reception) Manual Reception Remote Reception Automatic Answer [FAX] TEL/FAX Automation Switch TAD P[...]

40672201TX Rev.4 4 - 161 Table 4-3 Function Combination for Polling TX/RX Polling TX Polling RX Feeder TX Memory TX Closed Network Page Re-transmit Redial for Memory TX (Error) Sender ID Voice Request (Initiate) Voice Request (Reception) Call Back Message MCF (Single) MCF (Error) MCF (Mulriple) Manual TX Automatic Answer [FAX] TEL/FAX TAD Memory On[...]

40672201TX Rev.4 4 - 162 Table 4-4 Function Combinations during Communications Automatic Alternate Selecting Call Closed Network Sender ID *4 Page Retransmit Voice Request (Initiate) Stop TX Preparation Call Back Message Redial if Communication Error in Memory TX Voice Request (Reception) Functions Communication Mode TX Feeder Memory Manual Calling[...]

40672201TX Rev.4 4 - 163 Table 4-5 Preparation TX as Dual Access Reception Prefeed Remote input display Preparation TX Scanning to Memory Standby During FAX Calling During RING RESPONSE During detection of TEL/FAX During TAD detection 1st Phase B Calling ~ Transmission Transmission after scanning During Scanning Dialling and Calling During TX Diall[...]

40672201TX Rev.4 4 - 164 Table 4-6-1/2 User Default Setting 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 MCF (single-loc.) MCF (multi-loc.) ERR.REPORT (MCF.) IMAGE IN MCF. SENDER ID MONITOR VOLUME BUZZER VOLUME CLOSED NETWORK TX MODE DEFAULT T/F TIMER PRG. RING RESPONSE DISTINCTIVE RING 1'ST PAPER SIZE USER LANGUA[...]

40672201TX Rev.4 4 - 165 Table 4-6-2/2 User Default Setting 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 MCF (single-loc.) MCF (multi-loc.) ERR.REPORT (MCF.) IMAGE IN MCF. SENDER ID MONITOR VOLUME BUZZER VOLUME CLOSED NETWORK TX MODE DEFAULT T/F TIMER PRG. RING RESPONSE DISTINCTIVE RING 1'ST PAPER SIZE USER LANGUA[...]

40672201TX Rev.4 4 - 166 Table 4-7-1/2 Technical Default Setting 1 ODA 2 LTA 3 E-INT 4 GER 5 E-FRE 6 0-AUS 7 0-NZL 8 0-SIN 9 0-HNG 10 L-AG 11 IRL 12 DEN 13 SWE No. Technical Setting Items Setting Selection 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 ON/OFF ON/OFF USA INT'L GBR IRL NOR SWE FIN DEN G[...]

40672201TX Rev.4 4 - 167 Table 4-7-2/2 Technical Default Setting 14 NOR 15 SUI 16 AUT 17 HOL 18 ITA 19 ESP 20 Spare 21 Factory No. Technical Setting Items Setting Selection 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 ON/OFF ON/OFF USA INT'L GBR IRL NOR SWE FIN DEN GER HUN TCH POL SUI AUT BEL HOL FR[...]

40672201TX Rev.4 4 - 168 Table 4-8 Default Setting of Dial Parameters 24 SIN No. User Setting Items Setting Selection The contents of tables are subject to change by the requests of OEM comanies and customers without notice. Note: User settings are possible for items without mesh. REDIAL TRIES REDIAL INTERVAL DIAL TONE DETECT BUSY TONE DETECT MF (T[...]

40672201TX Rev.4 4 - 169 Table 4-9 Plug & Play ID 1 ODA 2 ATT 3 E-INT 4 GER 5 E-FRE 6 0-AUS 7 0-NZL 8 0-SIN 14 NOR 15 SUI 16 AUT 17 HOL 18 ITA 19 ESP 20 Spare (21) Factory 9 0-HNG 10 L-AG 11 IRL 12 DEN 13 SWE No. Close Setting Items Setting Selection Note 1 Plug & Play ID Default 00/01/02/03/04 00 00 01 01 01 04 04 04 01 01 01 01 01 01 00 0[...]

40672201TX Rev.4 5 - 1 Document Width NA Letter (216 mm) US/CANADA ISO A4 (210 mm) INT’L Communication mode/paper width Effective reading width Copy size G3/A4 G3/A4 Letter A4 215 mm for TX 203.2 mm for local copy* 208 mm for TX 203.2 mm for local copy* Note local copy: Printable reading width in local copy mode 5. DOCUMENT INPUT 5.1 Document Wid[...]

40672201TX Rev.4 5 - 2 5.5 Scanning Resolution (1) Horizontal resolution • 300 dots per inch in horizontal line. (2) Vertical resolution • 300 dots per inch, 15.4, 7.7, and 3.85 lines per milimeter in vertical direction. (switch-selectable) 5.6 Automatic Document Feeder Capacity The feeder will have the capacity to set and feed 20 documents she[...]

40672201TX Rev.4 5 - 3 5.8.3 Opacity The machine will properly reproduce documents which allow less than 40% of the scanner source light to pass through them. 5.8.4 Shape The feeding mechanism requires that input documents be rectangular in shape. The registration of triangular, circular and wavy-edge documents cannot be guaranteed. 5.8.5 Document [...]

40672201TX Rev.4 5 - 4 Figure 5-1 5.12 Document Jam Removal A means will be provided for the operator to manually release the feed mechanism to aid in clearing a jam. The operator will be able to clear 95% of all paper jams without tools or disassembly. The maximum number of operator-uncorrectable jams will be one in 10,000 of documents fed. 5.13 D[...]

40672201TX Rev.4 5 - 5 5.14 Document Stacking Documents up to 297 mm in length, which meet the basic weight and thickness specification, will exit on the stacker, and documents of letter or A4-size will stack in sequence. The documents will be placed on the feeder face down. The first sheet will be fed into the feeder first and will exit on the sta[...]

40672201TX Rev.4 6 - 1 6. DOCUMENT OUTPUT 6.1 Receive Printing Method Electro-photographic recording method using a LED (light emitting diode) array as the light source. 6.2 Effective Recording Width Printing area PW L T B Recording paper feeding direction EW R P L E L Printing area[...]

40672201TX Rev.4 6 - 2 Note: The printable area means the area allowing actual printing at the time of receiving. The guaranteed printing area means the area where the printing quality is guaran- teed. This table does not include vertical and horizontal addressing error ( ± 3 mm) of recording paper Letter Size A4 Size 14 inch Legal Size 13 inch Le[...]

40672201TX Rev.4 6 - 3 6.3 Recording Paper The approved paper for this machine will be Xerox 4200 type or equivalent. A fundamental technical specification will be provided to Customer by OKI to allow qualification of alternative sources. 6.3.1 Recording Paper The automatic feeder will operate with the following sizes. A4 : (210 mm x 297 mm) LETTER[...]

40672201TX Rev.4 6 - 4 6.4.3 Shape The feeding mechanism requires that Recording Paper be rectangular in shape. The registra- tion of triangular, circular and wavy-edge Recording Paper cannot be guaranteed. 6.4.4 Recording Paper Condition Only new paper is available. 6.5 Recording Paper Jam Detection Paper jam will occur when the top of the paper i[...]

40672201TX Rev.4 6 - 5 6.8 Recording Paper Skewing The maximum allowable skew of the recording paper is ± 1 mm over any advance of 100 mm. 6.9 Copy Density The density of a black image printed on plain paper will be greater than 1.2 O.D.* regardless of uniformity in all printing areas. The density of the white background (unprinted area) will be n[...]

40672201TX Rev.4 6 - 6 6.12 Toner Cartridge/Image Drum unit useful life 6.12.1 Toner Cartridge Useful life of Toner Cartridge is as below. 1,875 pages/4% duty (Duty means the ratio of black area in the white area) Note 1: The first toner cartridge installed a new image drum unit will have a decreased yield because the image drum unit itself has to [...]

40672201TX Rev.4 7 - 1 7. COMMUNICATION 7.1 Transmission Line The machine will reliably communicate with distant stations over voice-level telephone line. 7.2 Telephone Line Connection The machine will be connected to the telephone line via a Network Control Unit (NCU). One RJ-11 connector will be provided to connect the line. The machine will cont[...]

40672201TX Rev.4 7 - 2 7.4.1 Transmission Mode The machine is designed to change the message transmitting speed in accordance with the following fall-back plan, which is shown in the table 7-1. Table 7-1 Protocol 7.4.2 Signal Level The send will be -10.5 dBm for the US/Canada versions, -10dBm for the INT'L version and will be -11.5 dBM for the[...]

40672201TX Rev.4 7 - 3 7.6 Data Compression The machine will use the Modified Huffman (MH), Modified Read (MR) and Modified Modified Read (MMR) redundancy-reduction coding schemes. 7.7 Minimum Scan Line Time The minimum scan line time for communication is shown below. * 10 ms : 3.85 r /mm 5 ms : 7.7 r /15.4 r /mm 7.8 Compatibility All versions will[...]

40672201TX Rev.4 8 - 1 8. ENVIRONMENTAL REQUIREMENTS 8.1 Power 8.1.1 AC Voltage Range The machine will operate within A/B, as shown in Table 8-1. Operation within the ranges listed will be on a continuous basis. Table 8-1 Voltage Range Voltage Nominal Value MinimumValue Maximum Value Range (Volts) (Volts) (Volts) A: U.S./CANADA 120 102 127 B: INT?[...]

40672201TX Rev.4 8 - 2 8.1.4.1 US/CANADA Versions Table 8-2 Power Consumption 8.1.4.2 INT’L Versions Table 8-2 a Power Consumption ( ): Power save mode = ON * Chart: ITU-T No. 1 Mode Typical Power Max. Power (W) (W) Transmit 16 18 Receive 104 115 Copy W 141 157 Standby 5.4 6.1 Mode Typical Power Max. Power (W) (W) Transmit 18 20 Receive 102 112 C[...]

40672201TX Rev.4 8 - 3 8.1.5 Rush Current 15 times nominal current or 30A for 1/2 cycle 8 times nominal current or 15A for 3 cycle (Nominal current: copy mode) 8.2 Overheat Protection The heater in the fuser unit is controlled by the thermister and temperature control circuit. A built-in thermostat in the fuser unit prevents the heater from being o[...]

40672201TX Rev.4 8 - 4 8.6 Vibration The un-packaged machine will withstand 1/2 G vibration from 2 to 200 Hz for one hour. Sweeptime will be 1/2 octave per minute. Test methods will be in accordance with ASTM-D-3580-77T. 10 0 30 20 50 40 70 60 90 80 20 30 40 10 28 ° C 85% 27 ° C 80% 18 ° C 80% 10 ° C 73% 0 ° C 64% 32 ° C 54% 43 ° C 10 ° C 2[...]

40672201TX Rev.4 8 - 5 8.7 Static Electricity Electrostatic Discharge Immunity will meet as follows. Applicable Standard: EN50082-1/1992 Test method: IEC801-2/1984 8.8 Acoustic Noise Acoustic noise emitted by the machine will not exceed 55 dBA at 1 meter under any condi- tions. 8.9 Radiation Radio frequency interference and electromagnetic conducti[...]

40672201TX Rev.4 8 - 6 8.12 Storage Conditions The machine will not be affected by long-term storage under the following conditions: Relative humidity: 10 to 90 percent non-condensing Temperature: -10 to +50 degrees Celsius[...]

40672201TX Rev.4 9 - 1 9. SERVICEABILITY 9.1 Fault Isolation 9.1.1 Field problems will be diagnosed by replacement of circuit boards and mechanical components, with the aid of local diagnosis. 9.1.2 Problem diagnosis will be accomplished by the use of a standard 20 K ohm/volt volt-ohm meter (VOM). 9.1.3 Cables or special tools will be designed by O[...]

40672201TX Rev.4 10 - 1 G3 Basic Procedure T ime Image T ime FX-051 Initial 12.0 sec.(V17/29) Intermediate 2.5 sec.(V17/29) Final 4.0 sec.(V17/29) 14400 Standard 8.0 sec. Fine 1 1.0 sec. 10. OVERALL PERFORMANCE 10.1 Mean Time Between Failures (MTBF) The MTBF for the overall machine will exceed (3,000) hours of actual operation. The MTBF will be mea[...]

40672201TX Rev.4 10 - 2 10.4 Copy Resolution The resolution of the received copy will be as follows: Scanning: 200* dots/inch x 3.85 lines/mm or 300 dots/inch x 7.7 lines/mm or 15.4 lines/mm * : Convert from 300 to 200 Printing: 300 dots/inch x 784 lines/inch Note : The image smoothing process is used for printing. Resolution will be measured by tr[...]

40672201TX Rev.4 11 - 1 11. AGENCY LISTING/SAFETY REQUIREMENTS The machine will meet the agency listing requirements as set forth in the AGREEMENT to which this Specification is attached. This includes, but is not limited to, the following. A. UL, FCC, OSHA in the U.S. B. CSA, IC in Canada C. VDE, IEC, BABT, CEPT, CISPR, Applicable PTT’s regulati[...]

40672201TX Rev.4 12 - 1 12. SHIPPING CONDITIONS 12.1 Vibration The packaged product is tested by the vibration test of project 1A in the pre-shipment test of N.S.T.A. 12.2 Drop Test The packaged product will be tested by the drop test of project 1A in the pre-shipment test of N.S.T.A. 12.3 Static Compression The packaged product will withstand a lo[...]

40672201TX Rev.4 13 - 1 13. APPLICABLE DOCUMENTS 13.1 ASTM-D3332-77 ASTM: American Society for Testing and Materials Standard test methods for mechanical-shock fragility of products, using shock machines. Specification dated January 1978. 13.2 FCC Part 15, Class B Federal Communications Commision, U.S.A. Radio Frequency Devices — Part 15 13.3 NST[...]

40672201TX Rev.4 13 - 2 13.8 FCC Part 68, Subpart D Federal Communications Commision, U.S.A. Connection of Terminal Equipment to the Telephone Network - Part 68 Conditions for Regis- tration — Subpart D 13.9 IC CS-03 Issue 7 Industrie, Canada Standard for Terminal Equipment, and Connection Arrangements Systems, Network Protec- tion Devices 13.10 [...]

40672201TX Rev.4 13 - 3 13.15 EMC Directive 89/336/EEC (CE-mark) EN 50081-1/1992: Electromagnetic compatibility - Generic emission standard Part 1: Residential, commercial and light industry EN 50082-1/1992: Electromagnetic compatibility - Generic immunity standard Part 1: Residential, commercial and light industry 13.16 Unique International Requir[...]

40672201TX Rev.4 14 - 1 14. MACHINE PACKAGING AND CONFIGURATIONS 14.1 Shipping Carton Marking OKI will use a Customer-provided printing layout for the production of the shipping carton used for each machine. OKI will forward the shipping carton size requirements to Customer, when they are known. Customer will prepare and send to OKI the printing la[...]

40672201TX Rev.4 14 - 2 14.3 Machine Models Following machine models will form the basis for the configurations distributed worldwide by A. Model ODA (120V) - Designed to meet the requirements for the U.S. Canada. B. Model OEL - Designed to meet the requirements of Europe except GER/ UKF. C. Model GER - Designed to meet the requirements of BZT. Aus[...]

40672201TX Rev.4 14 - 3 FX-051 Packing Contents (Tentative) INT GER UKF INT Packaged contents in OUK Facsimile unit 1 1 1 1 1 1 1 I/D unit 1 1 1 1 1 1 1 Document stacker 1 1 1 1 1 1 1 Carrier sheet 1 1 Toner cartridge 1 1 1 1 1 AC power cord (GER) 1 1 AC power cord (Australia) 1 AC power cord * 1 1 TEL/LINE cable (*US) 1 1 TEL/LINE cable (FTZ) 1 TE[...]

Oki Data Corporation T okyo, Japan APPENDIX A MFP Function for FX-051 August, 1999[...]

T able of Contents 1. INTRODUCTION ....................................................................................................................... A-1 1.1 SUMMARY ........................................................................................................................ A-1 1.2 Host PC Function .................................[...]

40672201TX Rev.4 A-1 (Fig. 1) Printer (Hiper-W) Scanner (Oki-SCL) FaxModem (Class 1) Memory (MFPI.) Oki-MFPI IEEE 1284 Printer (Hiper-W) Scanner (Oki-SCL) FaxModem (Class 1) Memory (MFPI.) Oki-MFPI IEEE 1284 Application Layer Data Link Layer Physical Layer Host PC FX-051 1. INTRODUCTION 1.1 SUMMARY By installing the MFP software (Jet Suite), the fo[...]

40672201TX Rev.4 A-2 a) Application layer: Performs a function control of each sub-system at the Host PC and Fax machine. b) Data-Link layer: Performs a protocol control at the Host PC and Oki-MFPI (Packetize/Unpacketize,flow control, Transfers command/data between each sub-system) c) Physical layer: Has a bi-directional interface control circuit w[...]

40672201TX Rev.4 A-3 (Fig. 2) * Oki-MFPI • Packetized data flow. • Data=MFPL Command/Responce, Hiper-W Command/Responce • Designates "UNIT ID=Printer" • Contents becomes MFPL and Hiper-W command Bi-Centro I/F: Compatible & Nibble, MCE Mode Packet lnd Unit ID Length Contents Bi-Centro Receive FIFO buffer/Page Memory (Unpacketiz[...]

40672201TX Rev.4 A-4 1) Resolution: 300 dpi, Quasi-600 dpi 2) Smoothing OST-EX (Quasi-600 dpi) 3) Paper feed - Insert: 100 sheets/1st tray 1 sheet for manual feed 4) Paper feed - Eject: Face up, 30 sheets 5) Paper feed - Insert (option): None 6) 1st Tray - Paper size: Letter/A4/Legal 13"/Legal 14" 7) Medium support: Manual feed for Envelo[...]

40672201TX Rev.4 A-5 * B5 of DIN standard is not supported. B5 is only JIS standard. Recording Paper Letter Legal 13 Legal 14 Executive Monarch Envelope COM-10 Envelope DL Envelope C5 Envelope A4 A5 B5 (JIS) A6 Paper Size 8.50" x 11.0" 8.50" x 13.0" 8.50" x 14.0" 7.25" x 10.5" 3.87" x 7.50" 4.12&quo[...]

40672201TX Rev.4 A-6 (Fig. 3) * Oki-MFPI ¥ Packetized data flow. ¥ Designates "UNIT ID=Scanner" ¥ Contents becomes MFPL and Oki-SCL command Bi-Centro I/F: Compatible & Nibble, MCE Mode Packet lnd Unit ID Length Contents Bi-Centro Send Transmission Buffer Memory Scan Buffer (Transmission DMA) (Scanning DMA) (MFPI packetize by softwa[...]

40672201TX Rev.4 A-7 1) Scanning mode: Line Art/Dither/4,6 bit Multi-level (16, 64 Level Gray scale) 2) Sensor: CIS 300 dpi 3) Scanning resolution: Horizontal x Vertical scanning 8 dot/mm x 3.85/7.7/15.4 line/mm 75 dpi x 75 dpi (multi level only) 300 x 300 dpi/15.4 lines/mm 4) Zoom: 1 to 100% 5) Black and white reverse: Not provided 6) Mirror image[...]

40672201TX Rev.4 A-8 No. 1 2 Scanning direction Specification Document width: Min.; 148 mm (A5 width) Max.; 216 mm (Letter width) Document length: Min.; 100 mm Max.; 355.6 mm (Legal length) Note: When the document is less than 148mm (width) and 100mm (length), the document must be used with a carrier sheet. Item Used document size abc¥¥¥¥ Scann[...]

40672201TX Rev.4 A-9 2) Reading Area 3) Reading Size Effective Reading Area CIS Sensor Horizontal Scanning Direction Vertical Scanning Letter Length: 279 mm A4 Length: 297 mm Legal14 Length: 355.6 mm 215 mm 2.2 mm 2.2 mm (white) ••••••• 300 dpi Sensor Scanning direction Horizontal scanning direction Vertical scanning direction Reading[...]

40672201TX Rev.4 A-10 (Fig. 4) * Oki-MFPI • Packetized data flow. • Data=MFPL Command/Responce, TIA/AT Command/Responce • Designates "UNIT ID=FaxModem" • Contents becomes MFPL and TIA/AT command Bi-Centro I/F: Compatible & Nibble, MCE Mode Packet lnd Unit ID Length Contents Bi-Centro Receive Buffer Memory (Unpacketize) Class 1[...]

40672201TX Rev.4 A-11 (Fig. 5) * Oki-MFPI • Packetized data flow. • Data=MFPL Command/Responce, TIA/AT Command/Responce • Designates "UNIT ID=FaxModem" • Contents becomes MFPL and TIA/AT command Bi-Centro I/F: Compatible & Nibble, MCE Mode Packet lnd Unit ID Length Contents Bi-Centro Send Buffer Memory (Packetize) Class 1 Cont[...]

40672201TX Rev.4 A-12 (Fig. 6) * Oki-MFPI • Packetized data flow. Data=MFPL Command/Responce only • Designates "UNIT ID=RAM Memory" • Contents becomes only MFPL Bi-Centro I/F: Compatible & Nibble, MCE Mode Packet lnd Unit ID Length Contents Bi-Centro Send Transmission Buffer Memory User Programming (Transmission DMA) (Oki-MFPI p[...]

40672201TX Rev.4 A-13 (Fig. 7) * Oki-MFPI • Packetized data flow. Data=MFPL Command/Responce only • Designates "UNIT ID=RAM Memory" • Contents becomes only MFPL Bi-Centro I/F: Compatible & Nibble, MCE Mode Packet lnd Unit ID Length Contents Bi-Centro Receive Receiving Buffer Memory Dial Registration Memory (One-touch, Coded dial[...]

40672201TX Rev.4 A-14 2. CONCURRENT OPERATION Concurrent operation for the Fax machine can be classified the following combinations: 2.1 STANDALONE & HOST PC A part of MFP function for the simultaneous operation is possible during the Fax operation. 2.2 HOST PC & STANDALONE A part of Fax machine function for the simultaneous operation is po[...]

40672201TX Rev.4 A-15 Combination table of DUAL ACCESS and MULTI-TASKING capability * Basic designing conception in "DUAL ACCESS and MULTI-TASKING" • Performance for FAX machine (DUAL ACCESS) • Machine accepts to operator who handles the documents. • Machine accepts to automatic receiving. • Performance for MFP machine. (MULTI-TAS[...]

40672201TX Rev.4 A-16 GROUP ITEM COMMENT FX-051 (INT'L) Drivers Printer Driver Scanner Driver FAX Modem Driver Oki-MFPI Driver Installer Copy APP Setup APP Status Monitor APP PCFAX APP (including Viewer) Hiper-W TWAIN compatible. CLASS1 compatible This driver has follow operations mainly • Packet operations on Oki-MFPI • IEEE1284 (Bi-Centr[...]

40672201TX Rev.4 A-17 8.5” (2550) 8.0” (2400) 10.5” (3150) 0.25” (75) 0.25” (75) 0.17” (50) 0.17” (50) 11.0” (3300) 8.5” (2550) 0.25” (75) 0.25” (75) 0.17” (50) 0.17” (50) 12.5” (3750) 13.0” (3900) 8.0” (2400) 0.25” (75) 0.25” (75) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 8.5?[...]

40672201TX Rev.4 A-18 4.12” (1237) 3.62” (1087) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50)[...]

40672201TX Rev.4 A-19 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 0.17” (50) 4.13” (1240) 3.63” (1090) 5.33” (1598) 5.83” (1749) 7.16” (2149) 6.66” (1999) 9.62” (2885) 10.12” (3035) A6 B5 (JIS)[...]

40672201TX Rev.4 A-20 1 18 19 36 3. Bi-directional Parallel Interface IEEE 1284-B interface is used. 1) Connector • Printer side: 36-pin receptable • Cable side: 36-pin plug 2) Cable • IEEE Std 1284-1994 compliant cable is recommended for noise prevention. • Cable length: 6 ft (1.8m) max. 3) Connector pin arrangement 4) Signal level • Low[...]

40672201TX Rev.4 A-21 7) Interface circuit a) Receiving circuit b) Sending circuit +5V R R=3.3K Ω (1.0K Ω Strobe/Iprime) +5V 2.2K Ω (Open Collector)[...]

40672201TX Rev.4 A-22 Pin No. 1 2 - 9 10 11 12 13 14 15 16 17 18 19 20 - 27 28 29 30 31 32 33 34 35 36 Signal Name Data Strobe Data Bit n Acknowledge Busy Paper End Select Auto Feed - 0V Chassis Ground 5V 0V 0V 0V 0V 0V Input Prime Fault 0V - - Select In Signal Direction → Printer ↔ Printer Printer → Printer → Printer → Printer → → Pr[...]

Oki Data Corporation T okyo, Japan APPENDIX B F AX2NET Product Spefication for FX-051 September , 1999[...]

Contents 1. Outline ................................................................................................................................... B-1 2. F AX2NET Services ................................................................................................................ B-1 2.1 Service T ypes .....................................[...]

5. Procedure ............................................................................................................................ B-11 5.1 T elephone Number ................................................................................................. B-11 5.2 E-Mail Address ...............................................................[...]

40672201TX Rev.4 B-1 1. Outline This specifications describes the addition and modification caused to mount functions using FAX2NET service (that is a facsimile service via internet) in the FX-051. 2. FAX2NET Services 2.1 Service Types The FAX2NET service is a facsimile communication service using the FAX2NET-supplied internet. The FAX2NET server d[...]

40672201TX Rev.4 B-2 The FAX(B) only performs the normal G3 facsimile receiving operation; so, the user need not prepare a special protocol. (4) Web retrieval Request route: FAX(A) -> FAX2NET server (P) Receiving route: Web server (W) -> FAX2NET server (P) -> FAX(A) Web server (W) and server (P) are connected via internet. The FAX(A) and s[...]

40672201TX Rev.4 B-3 3.2 Destination Registration 3.2.1 E-mail Address Registration An E-mail address can be registered in up to 10 portions fitting to on-touch keys 1 to 10. Each address must be composed of up to 64 characters: uppercase letters, lowercase letters, digits, and symbols. For details on the applicable characters, see Section 5.4. The[...]

40672201TX Rev.4 B-4 3.3 Menus For details on the menus, see Operations. 3.3.1 User Program Add item “FAX2NET Server Registration” to No. 8. Under “FAX2NET server registration,” specify a FAX2NET server telephone number, FAX2NET account number, and international telephone prefix. 3.3.2 Location Program When “registration in one-touch key?[...]

40672201TX Rev.4 B-5 3.5 Characters Allocated to One-Touch Keys The following characters can be used on each character entry screen by allocating them to one-touch keys 1 to 6. The CAPS function is allocated to one-touch key 7; so, it is valid at entry of an E-mail address and Web URL. See Fig.3 FX-051 control panel. O.T. No.1 : . O.T. No.2 : _ O.T[...]

40672201TX Rev.4 B-6 UNIQUE 8.5" A4 B5 A5 OKIFAX AUTO REC SEARCH AUTO DIAL HYPHEN REDIAL HOOK V.REQUEST PHOTO EX FINE FINE STD LIGHT NORMAL DARK ALARM STOP START YES NO OKI * 0 # ABC DEF JKL MNO GHI TUV WXYZ PQRS 7 8 9 4 5 6 1 2 3 SELECT FUNCTION DELAYED TX REPORT PRINT PRINT OPERATION COUNTER DISPLAY CONF.TX LOCATION PROG. RELAY INIT.-TX USER[...]

40672201TX Rev.4 B-7 4. Functions 4.1 Single Destination Sending 4.1.1 International Call This function checks a destination telephone number prior to dialing and determines whether the FAX2NET function is to be used. When the FAX2NET server telephone number, account number, or international telephone prefix is not registered, a call is issued to a[...]

40672201TX Rev.4 B-8 4.1.2 E-mail Address When a one-touch key in which an E-mail address is registered is used as a destination, a call is issued to a FAX2NET server telephone number. If a FAX2NET server telephone number, account number is registered, an E-mail address is not accepted as a destination. While the fax is in the redial wait or delaye[...]

40672201TX Rev.4 B-9 4.3 Web Printing 4.3.1 Requests Web printing begins by selecting a one-touch key in which Web URL is registered as a destination. If information about a Web address or FAX2NET server is not registered, Web retrieval is invalid. To prepare for Web printing, first convert a character string registered as a Web address according t[...]

40672201TX Rev.4 B-10 4.5 Non FAX2NET Dialing In case the user does not desire the facsimile transmission via the FAX2NET server, the user can cancel dialing to the FAX2NET server by specifying "+" prior to dialing of the international telephone prefix. 4.6 Confidential and Relay Sending The FAX2NET function is not used for confidential a[...]

40672201TX Rev.4 B-11 (3) Telephone number registration application on PC The application or driver group for MFP function is not changed from FX051; therefore, the following item is limited: The telephone number registration application on PC cannot register an E-mail address in a one-touch key or change the contents for each one-touch key. The co[...]

40672201TX Rev.4 B-12 5. Procedure This section explains a protocol required to report a sending destination or requested Web page address from the FX051 to the FAX2NET server. 5.1 Telephone Number The figure below shows a procedure when the sending destination is a telephone number. FAX2NET server - TA < 10 sec.; TB < 6 sec. TC < T0 timer[...]

40672201TX Rev.4 B-13 5.2 E-mail Address The figure below shows a procedure when the sending destination is an E-mail address. FAX2NET server - TA < 10 sec.; TB < 6 sec. TC < T0 timer set value. At TA or TB timeout, the service code is 14D0. - The length of each DTMF tone is 300 ± 25ms. The time between digits is 100ms min. and 5 sec. max[...]

40672201TX Rev.4 B-14 5.3 Web Address The figure below shows a procedure for requesting a Web page. FAX2NET server - TA < 10 sec.; TB < 6 sec. set value. At TA or TB timeout, the service code is 14D0. - The length of each DTMF tone is 300 ± 25ms. The time between digits is 100ms min. and 5 sec. max. - The Account number, Web URL, and check s[...]

40672201TX Rev.4 B-15 5.4 Payment Card Registration The figure below shows a procedure for Payment Card Registration. - TA < 10sec. TB < 6sec. set value. At TA or TB timeout, the server code is 14D0. - The length of each DTMF tone is 300 ± 25ms. The time between digits is 100ms min. and 5sec. max. - The Account Number, Card Number, and Check[...]

40672201TX Rev.4 B-16 5.5 Character Conversion Table To report each E-mail address and Web address with a DTMF tone, digits, uppercase letters, lowercase letters, and symbols composing an address must be converted to a character string that can be expressed with DTMF tones. Each character must be expressed with a combination of two or three DTMF to[...]

40672201TX Rev.4 B-17 5.6 Check Sum The check sum is obtained by converting the transmitted DTMF tone string (Account No. + Control data field) values to character string according to ASCII code table 1 and adding them. In this case, the asterisk "*" between the account number and control data field is excluded. Example: “12345” + ‘[...]

40672201TX Rev.4 B-18 6. Operation 6.1 Function Selection Transition (1/2) POWER ON STANDBY MODE FUNCTION COPY SELECT FUNCTION COPY X 2 TECH. PROGRAMMING OT1 1 LOCAL TEST 1: SELF DIAGNOSIS 2: SENSOR CALIBRATION 3: LED TEST 4: TONE SEND TEST 5: MODEM SEND TEST 6: MODEM REC. TEST 7: MF (TONE) SEND TEST 8: TONE (TEL/FAX) TEST 2 TECH. FUNCTION 01: 02: [...]

40672201TX Rev.4 B-19 Function Selection Transition (2/2) USER PROGRAMMING OT9 FUNCTION 1 FUNC. PROGRAMMING 01: 02: 03: 04: 05: 06: 07: 08: 09: 10: 11: 12: 13: 14: 15: 16: 17: 18: 19: 20: 21: 22: 23: 24: 25: 26: 27: 28: MCF (SINGLE-LOC.) MCF (MULTI-LOC.) ERR.REPORT (MCF.) IMAGE IN MCF. SENDER ID MONITOR VOLUME BUZZER VOLUME CLOSED NETWORK TX MODE D[...]

40672201TX Rev.4 B-20 6.2 One-Touch Dial Registration Transition SELECT FUNCTION (OT) MEMORY AVAIL.=100% LOCATION PROGRAMMING ENTER (SRCH,O,A/D,#) ONE TOUCH KEY PRG. [FAX]YES( ) NO( ) ONE TOUCH KEY PRG. [EMAL]YES( ) NO( ) ONE TOUCH KEY PRG. [WEB]YES( ) NO( ) OT8 OT key When an E-mail address is already registered: When a Web address is already regi[...]

40672201TX Rev.4 B-21 6.2.1 Telephone Number Registration Transition SELECT FUNCTION (OT) MEMORY AVAIL.=100% LOCATION PROGRAMMING ENTER(SRCH,OT,A/D.#) ONE TOUCH KEY PRG. [FAX]YES( ) NO( ) NO=<FAX NO.> ID=<LOCATION ID.> NO=03 3404 7123 ID=NEWYORK OFFICE ILLEGAL OPERATION NO=0273 56 7890_ ID=NEWYORK OFFICE NO=0273 56 7890 ID=NEWYORK OFFIC[...]

40672201TX Rev.4 B-22 6.2.2 E-mail Address Registration Transition SELECT FUNCTION (OT) MEMORY AVAIL.=100% LOCATION PROGRAMMING ENTER(SRCH,OT,A/D.#) ONE TOUCH KEY PRG. [FAX]YES( ) NO( ) EMAIL: _ OT8 6 666……2 0……77 START key START key START key 666……77 OT key key CAPS OFF EMAIL: okitaro@okidata.co.j CAPS OFF EMAIL: okihanako@oki.co.jp_ C[...]

40672201TX Rev.4 B-23 6.2.3 Web Address Registration Transition SELECT FUNCTION (OT) MEMORY AVAIL.=100% LOCATION PROGRAMMING ENTER(SRCH,OT,A/D.#) WEB: http://_ ONE TOUCH KEY PRG. [WEB]YES( ) NO( ) OT8 START key START key START key 99……66 99……88 OT key key 3 sec. lapsed. CAPS OFF WEB: http://www.fax2net CAPS OFF EMAIL: p://www.fax2net.com_ C[...]

40672201TX Rev.4 B-24 6.3. Destination Registration Space Display/Registration T ransition 6.3.1 One-T ouch/Abbreviated Dial Registration T ransition SELECT FUNCTION (OT) MEMORY ABAIL.=100% LOCATION PROGRAMMING ENTER(SRCH,OT,A/D.#) ONE TOUCH NO.[01] YES( ) NO( /SRCH) ONE TOUCH NO.[01] [FAX]YES( ) NO( ) NO LOCATION AVAILABLE NO=<FAX NO.> ID=&l[...]

40672201TX Rev.4 B-25 6.3.2 T en Key Stack Calling T ransition SELECT FUNCTION (OT) MEMORY ABAIL.=100% 1234_ ONE TOUCH NO.[01] YES( ) NO( /SRCH) NO LOCATION AVAILABLE NO=1234 ID=_ NO=1234 ID=NEW YORK OFFICE NEW YORK OFFICE YES(STRT) NO(LOC.) NEW YORK OFFICE DIALING NO=<OR LOCATION> NO=_ PROGRAMMING NO=03 3404 7345 START key START key START ke[...]

40672201TX Rev.4 B-26 6.4 CAPS Key Function The CAPS key assigns OT7. E-mail address registration example EMAIL: OKI_ CAPS ON EMAIL: OKI_ CAPS OFF EMAIL: OKIdata_ CAPS OFF CAPS key Ten key Caps ON Mode Caps OFF Mode EMAIL: OKIdata_ CAPS OFF EMAIL: OKIdata_ CAPS ON EMAIL: OKIdataSYSTEM_ CAPS ON CAPS key Ten key Caps OFF Mode Caps ON Mode At entry of[...]

40672201TX Rev.4 B-27 6.5. User Setting T ransition SELECT FUNCTION (OT) MEMORY AVAIL.=100% 7:FAX NETWORK PRG. YES( ) NO( /1-9) 9:RESTRICT ID PRG. YES( ) NO( /1-9) 1:FUNC. PROGRAMMING YES( ) NO( /1-9) OT9 key key key key 7 1 7 9 1-9 1-9 1-9 See Section 6.5.1, “Facsimile Network Setting Transition.” 8:FAX2NET SERVICE YES( ) NO( /1-9) key key 8 1[...]

40672201TX Rev.4 B-28 6.5.1 Facsimile Network Setting T ransition 7:FAX NETWORK PRG. YES( ) NO( /1-8) SERVER TEL NO. NO=_ SERVER TEL NO. NO=03 5341 7700_ SERVER TEL NO. NO=03 5341 7700 ILLEGAL OPERATION key 03…… 03…… ACCOUNT NO. NO=_ ACCOUNT NO. NO=2160006612_ 216…… INTERNATIONAL PREFIX NO=_ INTERNATIONAL PREFIX NO=0041_ 0041 STARTkey *[...]

40672201TX Rev.4 B-29 6.6 F AX2NET SER VICE ILLEGAL OPERATION 1:WEB RETRIEVAL YES( ) NO( /1-2) 8:FAX2NET SERVICE YES( ) NO( /1-8) 3 sec. lapsed. When no account No. is registered. key key key 1 1-2 See Section 6.6.1, “Web Retrival Transition.” 2:PAYMENT CARD REG. YES( ) NO( /1-2) key key 2 1-2 See Section 6.6.2, “Payment Card Regist Transitio[...]

40672201TX Rev.4 B-30 6.6.1 WEB Retrieval Transition NOT PROGRAMMED 1:WEB RETRIEVAL YES( ) NO( /1-2) www.fax2net.com YES(START) NO(LOC.) 3 sec. lapsed. All 0T Web address not registered key NOT PROGRAMMED SELECT LOCATION 3 sec. lapsed. Web address not registered 0Tkey www.fax2net.com FAX2NET START key *1) *2) Standby *1) One-touch keys 1 to 10 only[...]

40672201TX Rev.4 B-31 6.6.2 P A YMENT CARD REGIST MEMORY OVERFLOW 2:PAYMENT CARD REG. YES( ) NO( /1-2) 3 sec. lapsed. FUNC. NOT AVAILABLE NO.=< CARD NUMBER > 3 sec. lapsed. 3 sec. lapsed. 12345 key Memory near end R system alarm Transmission waiting with document key NO.=_ 12345 key R system alarm START key NO.=12345_ 0353585297 FAX2NET *1) S[...]

40672201TX Rev.4 B-32 6.7. Operation Rules 6.7.1 Outline of Operation (1) Selecting OT in which an E-mail address is registered 1) When OT is selected at confidential sending, relay request sending, polling reception, or tune dial before calling, message “ILLEGAL OPERATION” is displayed, and OT cannot be selected. At real-time calling, message [...]

40672201TX Rev.4 B-33 (6) Ten key character display sequence at registration of E-mail or Web address Ten key 1 1 Ten key 2 2 -> A -> B -> C Ten key 3 3 -> D -> E -> F Ten key 4 4 -> G -> H -> I Ten key 5 5 -> J -> K -> L Ten key 6 6 -> M -> N -> O Ten key 7 7 -> P -> Q -> R -> S Ten key 8 8 [...]

40672201TX Rev.4 B-34 7. Report 7.1 Configuration Report The following items are added unconditionally. (For details on the number of registered digits and types for each item, see Operation.) 7.2 Telephone Directory List Report Describe an E-mail address and Web URL at a one-touch definition portion. The E-mail address and Web URL must also be des[...]

40672201TX Rev.4 B-35 7.3 Lowercase Letter Description Support 7.3.1 Location ID A character string including lowercase letters and symbols can be described in the Location ID column of the following reports: - Telephone directory report (Total number of registered digits) - Broadcasting entry report (First 20 digits) - Broadcasting confirmation re[...]

40672201TX Rev.4 B-36 8. Service Codes The following service codes are assigned for the FAX2NET functions: - 909D A telephone number to be called was composed of only a dial prefix and international tele- phone prefix (and hyphen), and a sending destination telephone number to be transmitted to the FAX2NET server was not found. - 14D0 The FAX2NET s[...]