Oregon Scientific RMR603HGA manual

W ireless Thermo-Hygro Clock Model : RMR603HGA User Manual RMR603HGA lab test cover R2 1/14/04, 1:31 AM 1[...]

EN 1 CONTENTS Contents ................................................................... 1 Introduction .............................................................. 2 About Oregon Scientific .......................................... 2 Product Overview .................................................... 3 Front View ...........................[...]

EN 2 INTRODUCTION Thank you for selecting the Oregon Scientific TM Wireless Thermo-Hygro Clock (RMR603HGA). This device bundles precise time keeping, alarm, and temperature and humidity monitoring features into a single tool you can use from the convenience of your home. In this box, you will find: • Main unit • Remote sensor (THGR122NX) Keep t[...]

EN 3 PRODUCT OVERVIEW FRONT VIEW 1. SNOOZE / LIGHT : Press to activate backlight or snooze. 2. T emperature Area: Readings, trend line, sensor reception status and channel number 3. Humidity Area: Readings; trend line, and sensor battery status 4. Clock / Alarm Area: T ime, time zone, day of week, month, date, alarm and Atomic Clock reception statu[...]

EN 4 BACK VIEW 1. W all mount 2. Battery compartment 3. ° C / ° F switch 4. ZONE: Press to switch time zones, deactivate Atomic Clock signal reception 5. RESET hole 6. T able stand 1 2 3 4 5 6 RMR603HGA lab test R2 1/17/04, 4:52 PM 4[...]

EN 5 REMOTE SENSOR (THGR122NX) 1. LCD display 2. LED Status indicator 1 2 1 2 3 4 1. W all mount hole 2. RESET 3. Channel number (1 - 3) 4. Battery compartment (Battery compartment cover not shown) RMR603HGA lab test R2 1/17/04, 4:52 PM 5[...]

EN 6 CHANGE SETTINGS 1. Press and hold MODE for 2 seconds to enter setting mode. 2. Press UP or DOWN to change settings. 3. Press MODE to confirm. T ABLE ST AND OR W ALL MOUNT Insert the stand on the back of the product, or mount it on a wall with a nail. GETTING ST ARTED BA TTERIES Batteries are not supplied with this product. Y ou will need to pu[...]

EN 7 3. Place the sensor near the main unit. Press RESET on the sensor to initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor . (Refer to the Sensor Data T ransmission section for more information.) 4. Close the remote sensor ba[...]

EN 8 SEARCH FOR SENSOR To search for a sensor , press and hold MEM and CHANNEL for 2 seconds. If the sensor is still not found, check the batteries, obstructions, and remote unit location. Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure. This is normal and do[...]

EN 9 TURN A TOMIC CLOCK ON/OFF Perform this step if you cannot receive Atomic Clock signals. Press and hold ZONE for 2 seconds. Then, manually set the clock following the "Set Clock" instructions (below). SET CLOCK Y ou only need to do this if you have disabled the Atomic Clock feature (for example, if you are too far from or cannot recei[...]

EN 10 ACTIV A TE ALARM Press ((.)) to activate or deactivate the Alarm. shows in the Clock Area when the Alarm is activated. SNOOZE ALARM Press SNOOZE/LIGHT to silence the Alarm for 8 minutes. If no button is pressed, the Alarm will automatically silence after 2 minutes. It will then sound again after 8 minutes. TEMPERA TURE AND HUMIDITY This produ[...]

EN 11 If you use a sensor that collects only temperature data, humidity will not be shown. MINIMUM / MAXIMUM RECORDS Press MEM to toggle between current, maximum (MAX) and minimum (MIN) records for the selected sensor . T o clear the records, press and hold MEM for 2 seconds. A beep will sound to confirm that the memory has been cleared. TEMPERA TU[...]

EN 12 W ARNINGS This product is designed to give you years of service if handled properly . Observe the following guidelines: • Never immerse the product in water . This can cause electrical shock and damage the product. • Do not subject the main unit to extreme force, shock, or fluctuations in temperature or humidity . • Do not tamper with t[...]

EN 13 SPECIFICA TIONS MAIN UNIT DIMENSIONS L x W x H1 16 x 125 x 57 mm (4.57 x 4.92 x 2.24 inches) We ight 7.90 ounces with battery REMOTE SENSOR DIMENSIONS L x W x H 92 x 60 x 20 mm (3.6 x 2.4 x .79 inches) We ight 2.22 ounces without battery TEMPERA TURE Unit ° C or ° F Indoor Range -5 ° C to 50 ° C (23 ° F to 122 ° F) Outdoor Range -20 ° [...]

EN 14 FCC ST A TEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W arning: Changes or modifications to this unit not [...]

EN 15 DECLARA TION OF CONFORMITY The information below is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www .oregonscientific.com, or on the warranty card for this product) for all inquiries instead. We Name: Oregon Scientific, Inc. Address: 19861 SW 95 th Place, T ualatin, Oregon [...]

© 2004 Oregon Scientific. All rights reserved. P/N.: 086-003347-01 RMR603HGA lab test back cover 12/29/03, 10:29 PM 1[...]