Panasonic JS950D5C020 manual

User’s Ｍａｎｕａｌ POS Workstation Model No. JS-950 Series C ontent s For USA / For CA NADA English Read Me First …..….……..... 2 1.Getting S tarted 2.Operation 3.Appendix Before operating this product,please read the i nstructions carefully, and save this manua l for future use.[...]

■ For USA Federal Co mmunications Commission Ra dio Frequency Inte rference Statem ent This equipment has been tested and f ound to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC R ules. T hese limits are designed to provide reasonable protection against harmful interference when the equipment is o perated in [...]

English Read Me First Introduction Thank you for purchasing the JS-950 series Panasonic POS Workstation. This manual describes the instruct ions for the POS Workstation. Please read this manual carefu lly before using this product. List of JS-950 ser ies Product Name Model Number. Remarks JS-950WS-040 CPU:3.2GHz,Memory:512 MB or 1GB Main Unit POS W[...]

1. Getting Started ■ Precautions [POS Workstation: JS-950 series ] IMPORTANT Install a socket outlet adjac ent to the equipm ent so that it will be eas ily accessib le. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES AC CORDING TO THE INSTRUCTIONS. 1. Avoid Radio Frequency Interference Do not place[...]

■ Name of each part & function 1 4 2 3 5 6 1. Oper ator’s Display 2. Front SW cover 3. POP Holder 4. Rear Display 5. USB connector 6. Power SW Attention: Do not push Power SW by mist ake w hen you insert the USB connector. 4[...]

2. Operation ■ AC Cord Kit Installation 1. How to install the AC Cord (1) Carefully lay the Main Body Unit on a clear, flat surface as show n in figure (1). (2) Unpack the AC Cord, an d then connect it to AC Inl et as shown in figure (2). (3) Fit the Cord Clamp to AC Co rd, and fix it by attached screw as shown in figure (3)-1, 2 and 3. (4) Caref[...]

■ Display Unit Installation Be sure to disconnect the power cabl e of the ma in block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to install the display unit (1) Open the screw cover of t he main unit (POS Workstation). (2) Hold the display unit with both h ands and in sert the connector section of the [...]

■ Storage Unit Install ation Be sure to disconnect the power cabl e of the ma in block (POS Workstation) and confirm the power is “OFF” before th e operation below. 1. How to mount the storage unit (1) Disconnect the 2 latches on the upper portion of the filter cover of the main unit by both hands, pull the cover tow ard you while pressing th[...]

■ Rear Display Unit Installation Be sure to disconnect the power cabl e of the ma in block (POS Workstation) and confirm the power is “OFF” before th e operation below. 1. How to mount the rear display unit (1) Loosen the thumbscrew on the lower portion of th e rear cover at the rear display side of the main unit by hand, and re move the rear[...]

2. How to replace the rear display (1) Loosen the thumbscrew on the lower portion of the rear cover o f the main unit by hand, and remove the rear cover. * The thumbscrew shall be loosened unti l the screw rotates without resistance. (2) Disconnect the connector of the rear disp lay from the connector of the main unit. (3) Loosen the 2 thumbscrews [...]

■ 2nd display unit Installation Be sure to disconnect the power cabl e of the ma in block (POS Workstation) and confirm the power is “OFF” before th e operation below. 1. How to mount the 2nd Display Unit (1) Loosen the thumbscrew on the lower portion of th e rear cover at the rear display side of the main block by hand, and remove the rear c[...]

2. How to replace the 2nd Display U nit (1) In case of 950SD010, disconnect VGA c able and speaker cable from I/O panel. (2) Loosen the thumbscrew on the lower portion of the rear cover of the main block by hand, and remove the rear cover. * The thumbscrew shall be loosened unti l the screw rotates without resistance. (3) Disconnect the connector o[...]

■ ID module Unit installation Be sure to disconnect the power cabl e of the ma in block (POS Workstation) and confirm the power is “OFF” before th e operation below. 1. Conte nts Cabl e cover Peripheral screw (Use only ID module 1pcs Screw 2pcs Long type 1pcs 2pcs Dallas KEY r eader) Short type 1 pcs Cabl e clamp 1pcs 2. How to mount the ID m[...]

13 Tighten the screw to clam p the cable and wiring the cable as shown in the fig. (10)-4. (11) Slide USB cable cover as shown i n the fig. (11)-1. In case of Dallas KEY reader, slide the USB cable cover with care to avoid th e cable from the rib of the USB cable cover as show n in the fig. (11)-2. (12) Put the supplied 2 peripheral screws in from [...]

3. How to replace the ID module unit (1) Remove Display Unit accordin g to Display Unit Installation. (2) Prepare an ID mod ule unit to be used. * The ID module unit is supplied with 2 p ieces of peri pheral screws, 2 pieces of screws, 1 piece of long cable cover, and 1 piece of short cable cover as accessories. (3) Slide the USB cable cover toward[...]

3. Appendix ■ Specifications [Common Specifications] Environmental condition Item Specification Operating Temperature +5°C – +40°C Operating Humidity 15% RH – 85% RH (no dew) Strage Temperature -30°C – +60°C Strage Humidity 10%RH – 90%RH [POS Workstation: JS-950WS- ・・・ ] Item Specification Power Supply input AC100V-240V, 50/60 H[...]

IO Connector layout (1) Bottom IO Connector layout COM 3 Printer USB2 LAN (Powere d) (2) Rear Display Connector Layout (3) Front IO Connector layout SW & LED USB #5 Soft Switch LAN LED HDD LED Power LED VGA C/D2 COM 1 ○○○○ ○○○○ ○ ○○○○○○○○○○○○ ○○○○○○○○○○○○○ ○○○○○ ○?[...]

Outside drawing Main Body 12” Touch Scre en 15” Touch Scre en 17[...]

[Touch Display Unit: JS-950D ・・・・・ ] Item Specification Size 12.1”: Approx. W320mm x D153mm x H256mm 15”: Approx. W364mm x D153mm x H300mm Mass 12.1”: Approx. 3.4 kg 15”: Approx. 4.4 kg Outside drawing (1) 12.1” resistive TP Display, 12.1” capacitive TP Display (2) 15” resistive TP Display, 15” capacitive TP Display 18[...]

[Storage module Unit: JS-950H ・・・・・ ] Item Specification Size Approx. W171mm x D126.5mm x H34mm Mass Approx. 0.8Kg (3.5”), 0.5Kg(2x CF) Outside drawing 3.5HDD module, Dual CF module 19[...]

[Rear Display Unit: JS-950RD- ・・・ ] Item Specification Size Approx. W216.5mm x D29mm x H90mm Mass Approx. 0.4Kg (2 Lines), 0 .5Kg (4Lines) Outside drawing Rear Display Module 2line, Rear Display Module 4line Rear Display module 2line Rear Display module 4line 20[...]

[2nd Display Unit: JS-950SD- ・・・ ] Item Specification Note: It is not possible to use it together with the Rear Display Unit. Size Approx. W250mm x D72mm x H335mm Mass Approx. 1.4kg Outside drawing 21[...]

[MSR Unit: JS-950MG-010 ] Item Specification accessories 2 pieces of peripheral screws 2 pieces of screws 1 piece of long cable cover 1 piece of short cable cover Note: MSR, Dallas Key and Fingerpri nt can not be used at the same time. Size Approx. W63mm x D49mm x H140mm Mass Approx. 0.1 kg Outside drawing 22[...]

[Dallas Key Reader Unit: JS-950DP-010 ] Item Specification accessories 2 pieces of peripheral screws 2 pieces of screws 1 piece of long cable cover 1 piece of short cable cover Note: - Work in virtual COM I/F - MSR, Dallas Key and Fingerprint can n ot be used at the same time. Size Approx. W73mm x D49mm x H100mm Mass Approx. 0.15 kg Outside drawing[...]

[Fingerprint Sensor Unit: JS-950FS-010 ] Item Specification accessories 2 pieces of peripheral screws 2 pieces of screws 1 piece of long cable cover 1 piece of short cable cover Note: MSR, Dallas Key and Fingerpri nt can not be used at the same time. Size Approx. W73mm x D49mm x H100mm Mass Approx. 0.1 kg Outside drawing 24[...]

■ Cleaning C leaning of outer case Light soil - Wipe case lightly with a dry, soft cloth. Heavy soil - Wipe case lightly with soft cloth pr e-m oistened with very diluted, mild detergent. Lightly wipe case dry with a dry, soft cloth. Cleaning of Display Wipe display gently with a dry, soft cloth to remove l ight dirt and dust. Do not wipe or pres[...]

■ Operation Attention for capacitive touch scr een (1) Do not touch it by finger nail, because c apacitive touch screen can not recognize it. Touch it by finger tip. (2) Do not touch it during startup. It initializ es touch screen during star tup. If it is touched during startup, touch screen is not initialized correc tly. (3) Be careful to not a[...]

Specifications and manuals are subject to change without notice. Microsoft and Wind ows are registered trademarks of Microsoft Co rporation in the United State of America and other co untries. Intel and Celeron D are trademarks or registered trademarks of Intel Corporation in the United State of America and other countries. is a registered of trade[...]