Panasonic PT-DW5100U manual

DLP ® Based Projector Commercial Use Operating Instructions Read these instructions completely before operating this unit. TQBJ0219 Model No. PT -D5700U PT -D5700UL PT -DW5100U PT -DW5100UL[...]

2 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLP ® based projector. The serial number of your product may be found on its back. You should not[...]

3 W ARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in[...]

4 Contents IMPORTANT SAFETY NOTICE ..................................2 Precautions with regard to safety ............................5 Accessories ................................................................7 Precautions on handling ...........................................8 Name and function of parts .......................................9 [...]

5 Precautions with regard to safety W ARNING If you notice smoke, strange smells or noise coming from the projector , disconnect the power cord plug from the wall outlet. • Do not continue to use the projector in such cases, otherwise fire or electric shocks could result. • Check that no more smoke is coming out, and then contact an Authorized [...]

6 Precautions with regard to safety Do not set up the projector in humid or dusty places or in places where the projector may come into contact with oily smoke or steam. • Using the projector under such conditions may result in fire, electric shocks or plastic deterioration. The plastic deterioration may cause the falling down of the projector wh[...]

7 Accessories Check that all of the accessories shown below have been included with your projector. If the lamp has broken, ventilate the room immediately . Do not touch or bring your face close to the broken pieces. • Failure to observe this may cause the user to absorb the gas which was released when the lamp broke and which contains nearly the[...]

8 Precautions on handling Precautions on transport Make absolutely sure that the lens cap is in place when transporting the projector or carrying it around. Both the projector and the projection lens are precision-made and, as such, are susceptible to vibration and impacts. When transporting the projector and lens or carrying them around, place the[...]

9 Name and function of parts Remote control operation indicator lamp The lamp flashes when any remote control button is pressed. POWER STANDBY ( ) button (page 25) Switched the power to the “ standby ” mode if the MAIN POWER has been put to the “ l ” position. POWER ON ( I ) button (page 24) Turns on the power if the MAIN POWER has been put[...]

10 Name and function of parts Remote control transmitter window Operate the remote control aiming at the remote control receiver window on the main unit. Remote control wired terminal (page 15) To use the wired output terminal, connect the remote control and the main unit with the M3 stereo mini jack cable available in the market. LENS (FOCUS, ZOOM[...]

11 AC IN terminal (page 24) Connect the supplied line power cord into this receptacle. Do not connect any other cable to this socket. Air filter (page 55) Burglar lock Attach a commercial burglar prevention cable (e.g., from Kensington) to this lock port. It is compatible with the Microsaver Security System from Kensington. Clasp for attaching anti[...]

12 Name and function of parts Lamp unit cover The lamp unit is housed. MAIN POWER switch (page 24) Use this switch to turn on “ I ” and off “ O ” the main power applied to the projector. Remote control receiver window (rear) (page 14) This also receives the signal beam coming from the remote control. POWER ON ( I ) button (page 24) Turns on[...]

13 VIDEO IN terminal (page 23) An input terminal for video signals. (BNC) S-VIDEO IN terminal (page 23) An input terminal for S-Video signals. (MIN4-pin DIN) This terminal complies with S1 signals and automatically toggles between 16:9 and 4:3 according to the size of input signals. RGB 1 input (RGB 1 IN) terminal (page 23) A terminal to input RGB [...]

14 Using the remote control unit Loading dry cells When loading batteries into the battery compartment of the remote control, make sure that their polarities are correct. 1. Open battery compartment lid. Open the lid in the order of steps and . 2. Insert the dry cells. Into battery compartment, with their polarities orientated as indicated ( , ) in[...]

15 Setting projector ID number to remote control Every projector has its ID number and the ID number of the controlling projector must be set to the remote control in advance so that the user can operate the remote control. The ID number of the projector is set to “ ALL ” on shipping, and use the ID ALL button of the remote control when using o[...]

16 Installation FRONT REAR FLOOR CEILING (Default position) Installation geometry When planning the projector and screen geometry, refer to the figure below and the information on the next page for reference. After the projector is roughly positioned, picture size and vertical picture positioning can be finely adjusted with the powered zoom lens an[...]

17 Projection distance by projection lens Listed in the table below are the lens projection distances for the PT-D5700U (lens included), PT-D5700UL (lens sold separately), PT-DW5100U (lens included) and PT-DW5100UL (lens sold separately). • PT-D5700U, PT-D5700UL Unit : m, ( ) : inch, [ ] : foot Screen aspect ratio 4:3 1.27 (50") 1.52 (60&quo[...]

18 Installation Unit : m, ( ) : inch, [ ] : foot Screen aspect ratio 16:9 1.27 (50") 1.52 (60") 1.78 (70") 2.03 (80") 2.29 (90") 2.54 (100") 3.05 (120") 3.81 (150") 5.08 (200") 6.35 (250") 7.62 (300") 8.89 (350") 10.16 (400") 12.70 (500") 15.24 (600") Diagonal length (SD) He[...]

19 * 1 The throw ratio is based on the value during projection onto an 80-inch screen size. * 2 The height position (H) of the ET-DLE050 is SH/2. • PT-DW5100U, PT-DW5100UL (0.8:1) (1.3 – 1.8:1) (1.8 – 2.5 :1) (2.5 – 4.0:1) (3.4 – 4.5:1) (4.5 – 8.4:1) Unit : m, ( ) : inch, [ ] : foot Screen aspect ratio 15:9 1.27 (50") 1.52 (60"[...]

20 Installation 1.48 [4.85] 1.78 [5.85] 2.09 [6.85] 2.39 [7.85] 2.70 [8.86] 3.00 [9.86] 3.61 [11.86] 4.53 [14.86] 6.05 [19.86] 7.58 [24.86] 9.10 [29.86] 10.63 [34.87] 12.15 [39.87] 15.20 [49.87] 18.25 [59.88] 2.01 [6.58] 2.42 [7.93] 2.83 [9.28] 3.24 [10.63] 3.65 [11.98] 4.06 [13.32] 4.88 [16.02] 6.12 [20.06] 8.17 [26.80] 10.23 [33.55] 12.28 [40.29][...]

21 Note • The dimensions in the table in pages 17-20 and the values obtained from the above formulas may contain slight errors. • When an SXGA signal is input and projected, the right and left ends of the picture will be blanked and the aspect ratio will be 5:4. • The brightness is different between the wide lens position settings and telepho[...]

22 Connection Setup precautions • Before connecting any of your video/audio equipment to the projector, carefully read the owners manual supplied with the equipment once again. • All cable connections should be made with the entire system devices, including the projector, first turned off. • Obtain commercial interconnecting cables for device[...]

23 Example of connecting with PCs RGB 2 IN VD SYNC/HD B/P B G/Y R R/P SERIAL REMOTE 1 REMOTE 2 IN IN OUT LAN DVI-D IN RGB 1 IN VIDEO IN S-VIDEO IN IN OUT RGB 2 IN VD SYNC/HD B/P B G/Y R R/P SERIAL REMOTE 1 REMOTE 2 IN IN OUT LAN DVI-D IN RGB 1 IN VIDEO IN S-VIDEO IN IN OUT DVI-D Cable (available in the market) PC with DVI-D terminal PC PC Control P[...]

24 Projection Powering up the projector When using an optional lens, install a projection lens before powering up the projector. (Refer to page 26.) Remove the lens cover beforehand. Connect the supplied power cord. (120 V AC, 50 Hz/60 Hz) Press the “ I ” marked side of the MAIN POWER switch to turn on the power . The power indicator lights up [...]

25 Powering off the projector Press the POWER ST ANDBY “” button. Select “ OK ” with or button and press the ENTER button. (Or press the POWER ST ANDBY “” button again.) The projection of the image stops, and the power indicator of the main unit lights up orange. (The cooling fan keeps running.) W ait until the power indicator of the ma[...]

26 How to adjust the lens How to install and remove the projection lens How to install the projection lens Align the guide of the projection lens with the guide groove in the main unit. T urn the lens clockwise until it clicks into place. How to remove the projection lens T urn the lens counterclockwise as far as it will go. While holding down the [...]

27 Automatic adjustment (AUT O SETUP) Automatic adjustment function adjust the resolution, clock phase and image position automatically when dots-structured analog RGB signals such as computer signal are supplied. (Automatic adjustment is not available if moving picture input signals or signals having a dot clock frequency of more than 150 MHz are [...]

28 On-screen menus Structure of menu screens Menus are extensively used for configuring, adjusting or reconfiguring the projector. The menus structure is as follows: MAIN MENU PICTURE POSITION ADVANCED MENU DISPLAY LANGUAGE OPTION1 OPTION2 TEST PATTERN NETWORK SECURITY SUB MENU MENU SELECT NETWORK HOST NAME DHCP IP ADDRESS SUBNET MASK GATEWAY NETWO[...]

29 Returning to the previous page • Pressing the MENU button returns the screen to the previous menu page. • When the MAIN MENU is on the screen, pressing the MENU button clears all menus from the screen. Menu items shown in black characters • Some menu items may not be valid for certain signal formats applied to the projector. The menu items[...]

30 Adjusting the picture PICTURE MODE The picture mode can be selected from the following depending on viewing conditions and the video signal source in use: DYNAMIC : Picture brightness/contrast ratio is increased to suit brighter viewing environments. GRAPHIC : The picture becomes suitable for input from to the personal computer. STANDARD : The p[...]

31 Adjusting the position POSITION SHIFT ASPECT ZOOM CLOCK PHASE KEYSTONE MENU SELECT 4:3 +16 SUB MENU SHIFT The position where the images are displayed can be moved here. : The position is moved horizontally. : The position is moved vertically. ASPECT AUTO : (For S-Video/Video signals only) At this setting, when S1 video signals* 1 are identified [...]

32 Adjusting the position • If the picture size is compressed or enlarged by using the 16:9 aspect ratio when the projector is used for profitable purpose or in the presence of an audience (for example, in a coffee shop or at a hotel etc.), it may infringe the rights of the copyright owner of the original picture. • If a picture with the standa[...]

33 INPUT RESOLUTION Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. : These select the items listed below. : These select the value. “ TOTAL DOTS ” , “ DISPLAY DOTS ” , “ TOTAL LINES ” and “ DISPLAY LINES ” Each item automatically displays a value in response to th[...]

34 How to use ADV ANCED MENU Changing the display language RASTER POSITION When the whole area where the input picture can be displayed is not used, the picture can be moved to any position inside the display area. : These adjust the value in the horizontal direction. : These adjust the value in the vertical direction. XGA MODE This mode takes effe[...]

35 OPTION1 settings OPTION1 COLOR MATCHING COLOR CORRECTION CONTRAST MODE AUTO SIGNAL BACK COLOR STARTUP LOGO SUB MEMORY LIST DVI EDID CHANGE MENU SELECT OFF USER NORMAL OFF BLUE OFF EDID2:PC DVI SIGNAL LEVEL 0-255:PC FUNC1 OSD POSITION 1 OSD MEMORY ON COLOR MA TCHING When multiple sets are used simultaneously, this projector allows the user to cor[...]

36 OPTION1 settings COLOR CORRECTION OFF : This is the standard setting. USER : The six colors of red, green, blue, cyan, magenta and yellow can be adjusted and registered for each of four signal systems: Video, S-Video, RGB and YP B P R . Press the ENTER button to make the detailed settings. RETURN STORE SUB MEMORY LIST - : RGB1-XGA60 1: RGB1-XGA6[...]

37 DVI EDID When the projector and external equipment are connected by DVI connection but a proper image cannot be obtained, switch this setting. EDID1 Select this mainly when external equipment (DVD player, etc.) that outputs movie video signals is connected to the DVI terminal. EDID2:PC Select this mainly when external equipment (personal compute[...]

38 OPTION2 settings OPTION2 PROJECTOR ID INSTALLATION ALTITUDE DIRECTION LAMP SELECT LAMP RELAY LAMP POWER RS-232C CHANGE MENU SELECT ALL FRONT-FLOOR LOW HORIZONTAL DUAL OFF HIGH SYSTEM INFORMATION AUTO POWER OFF DATE AND TIME DISABLE PASSWORD PROJECT OR ID The projector has an ID number setting function that helps the user to control two or more p[...]

39 LAMP SELECT “ LAMP SELECT ” is used to choose from “ SINGLE ” and “ DUAL ” modes depending on user ’ s needs or viewing conditions. In “ SINGLE ” mode, the projector may automatically select either lamp from the 2 lamps, or the particular lamp can be specified. DUAL : Two lamps are used simultaneously. SINGLE : One of either la[...]

40 OPTION2 settings Displaying the internal test pattern SYSTEM INFORMA TION The projector ’ s system information can be viewed. SYSTEM INFORMATION MAIN VERSION NETWORK VERSION PROJECTOR RUNTIME LAMP1 LOW HIGH TOTAL LAMP2 LOW HIGH LAMP1 ON TOTAL RETURN LAMP2 ON 1.00.00 1.00 300h 100h 200h 300h 100h 200h 300h 20 20 AUT O POWER OFF The projector ca[...]

41 Setting the network The settings required for the network must be established in order to use the Web browser (page 42) functions that the PC uses to control the projector. HOST NAME : Make alteration if necessary when to use the DHCP server. DHCP : Set the DHCP item to ON when to acquire an IP address automatically using the DHCP server. Set to[...]

42 Using W eb Browser Control Accessing from the W eb browser Start the Web browser on your PC, then enter the IP address which was set in the projector . Enter “ user1 ” in the user name field, then enter the password in the password field. The default setting is “ panasonic ” (all lower case). If you have changed the password, enter the n[...]

43 Basic control page This page is the first page displayed when the projector is accessed through a Web browser. To move from another page, click [Projector control], then [Basic control]. Detail control page Click [Projector control], then [Detail control] to display the Detail control page. Control button Click this item, and a projector control[...]

44 Using Web Browser Control Error information page When is displayed on the status information screen, click it to display the error details. • Depending on the nature of the error, the projector may be placed in the standby mode for its own protection. Note Monitor information page Click [Projector control], then [Status information] to display[...]

45 When [FAILED] has appeared for an item Parameter MAIN CPU BUS FAN OPTICS MODULE TEMPERATURE INPUT AIR TEMPERATURE AROUND LAMP TEMPERATURE LAMP REMAIN TIME LAMP STATUS SHUTTER AIR FILTER OPTICS MODULE TEMP.SENSOR INPUT AIR TEMP.SENSOR AROUND LAMP TEMP. SENSOR BATTERY AIRFLOW SENSOR COLOR WHEEL COVER OPEN Description Trouble has occurred in the mi[...]

46 Using Web Browser Control • Only alphanumeric characters, “ . ” , “ _ ” , “ - ” , or “ @ ” are available to set an E-mail address. Note Periodic warning interval setting (E-mail is sent on the checked days of the week/times) Enter the E-mail address of your desired recipient. Select the conditions for sending E-mail. ERROR: an [...]

47 Authentication server set up page The authentication server is set on this page when POP authentication or SMTP authentication is required for mail transmissions . Click [Network set up], then [Authentication set up] to display the authentication server set up page. For SMTP authentication, change the authentication method to use, as desired. Ch[...]

48 Using Web Browser Control Contents of mail sent • Mail with the contents shown below is sent when the E-mail settings have been established. Adjust clock page Click [Network set up], then [Adjust clock] to display the Adjust clock page. • Mail with the contents shown below is sent when an error has occurred. • If the time becomes incorrect[...]

49 Network config page Click [Network set up], then [Network config] to display the Network config page. Network status page Click [Network set up], then [Network status] to display the Network status page. Set this to ON to enable the DHCP client function. Enter the IP address if DHCP server is not used. Enter the gateway address if DHCP server is[...]

50 Using the PJLink ™ protocol The network functions of the projector are compatible with PJLink ™ Class 1. The operations mentioned below can be performed from a personal computer using the PJLink ™ protocol. • Projector settings • Projector status inquiry Supported commands The commands for controlling the projector using the PJLink ™[...]

51 Setting the security The projector ’ s security function enables the password input screen to be displayed or a company ’ s URL address to be set and displayed underneath the projected images. PASSWORD SET INPUT (When using the projector for the first time) Press the , , , , , , and buttons in this order, and press the ENTER button. (When th[...]

52 Pin assignments and signal names Communication conditions (Factory setting) Basic format Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control. The main unit is equipped with SERIAL terminals located in its terminal section on the side, [...]

53 Using the REMOTE2 IN terminal provided on the side of the main unit, it is possible to operate the projector from a control panel etc. furnished in a distant location where infrared remote control signal cannot be received. Pin assignments and control Be sure to short-circuit Pins and when controlling. Using the REMOTE 2 terminal D-Sub 9-pin (fe[...]

54 Indication of lamp monitor This projector is equipped with 3 indicators to show when a lamp needs replacement or there is an abnormal internal temperature. These lamps flash or light up to indicate a problem. Turn the power off and follow the steps below. T emperature monitor (TEMP) Lamp 1 monitor (LAMP 1) Lamp 2 monitor (LAMP 2) (Power indicato[...]

55 Cleaning and replacement of air filter If too much dust accumulates on the air filter, [CLEAN THE AIR FILTER]* appears at the lower left of the screen, and the temperature monitor (TEMP) will blink once. If even more dust is allowed to accumulate, the temperature inside the main unit will rise, the temperature monitor (TEMP) will blink twice, an[...]

56 Replacing the lamp unit Precautions on lamp unit replacement Remove the power plug and confirm that the surroundings of the lamp unit have cooled off. Be careful when handling a light source lamp. The lamp unit has high internal pressure. If improperly handled, explosion might result. A used lamp unit may burst if it is handled violently. For di[...]

57 Lamp unit replacement steps T urn the power off by following the steps on page 25, remove the power plug and confirm that the surroundings of the lamp unit have cooled off. Check that the fan has stopped running. Have a Phillips screwdriver ready ahead of time. Remove the screw securing the lamp unit cover , and then slide the lamp unit cover a [...]

58 Ceiling Mount Bracket Safeguards The projector and the ceiling mount bracket are designed sufficiently safety though, make sure the safety cable provided with the projector is installed and attached to the bottom of the projector when mounting in the ceiling for safety and security. Installation work of the ceiling mount bracket should only be c[...]

59 Before asking for service --- check the following points. Symptoms Checks • Is the power cord plug correctly plugged in? • Is the MAIN POWER turned on? • Is electricity running to the power outlet? • Is the temperature monitor (TEMP) indicator on the front of the unit flashing or turned on? (See page 54) • Is the lamp monitor (LAMP) in[...]

60 Specifications PT -D5700U PT -D5700UL PT -DW5100U PT -DW5100UL Power supply AC 120 V, 50 Hz/60 Hz Power consumption 770 W (about 10 W in standby without fan running) Amps Maximum 8 A DLP ® panel Panel size Display system Number of pixels 0.7 inch (aspect ratio 4:3) 0.65 inch (aspect ratio 15:9) DLP ® chip x 1, DLP ® type 786 432 pixels (1 024[...]

61 Interface ports RGB2 input terminal Video input terminal S-Video input terminal Serial input/output terminal Remote1 input/output terminal Remote2 input terminal DVI-D input terminal LAN terminal 1 set of high-density, D-Sub 15-pin (female) [For YP B P R input] Y: 1.0 V [p-p] synchronization signal included, P B P R : 0.7 V[p-p] 75 Ω [For RGB [...]

62 Compatible Signal List NTSC/NTSC4.43/ PAL-M/PAL60 PAL/PAL-N/SECAM 480i 576i 480p 576p 1080/60p 1080/50p 1080/60i 1080/50i 720/60p 720/50p VGA400 VGA480 SVGA MAC16 XGA MXGA WXGA MAC21 MSXGA SXGA UXGA 720 720 720 720 720 720 1 920 1 920 1 920 1 920 1 280 1 280 640 640 640 640 640 640 640 800 800 800 800 800 832 1 024 1 024 1 024 1 024 1 024 1 024 [...]

63 Dimensions >PC< TBMU448 RGB 2 IN VD SYNC/HD B/P B G/Y R R/P SERIAL REMOTE 1 REMOTE 2 IN IN OUT LAN DVI-D IN RGB 1 IN VIDEO IN S-VIDEO IN IN OUT 86.5 (3 13 / 32 ) 167 (6 12 / 64 ) 157 (6 3 / 16 ) 530 (20 55 / 64 ) 436 (17 11 / 64 ) 368 (14 31 / 64 ) 425 (16 47 / 64 ) 441 (17 23 / 64 ) 4 ( 5 / 32 ) 12 ( 15 / 32 ) R30 478.5 (18 27 / 32 ) unit[...]

64 Note: Purchase of this equipment includes the rights to use this software (the built-in microcomputer and information recorded on ROMs) but does not grant copyrights. Do not reverse engineer, change or modify the software. The guarantee will not be valid for any malfunctions caused by such actions. T rademark Acknowledgement • VGA and XGA are [...]

65 NOTES IMPORT ANTES CONCERNANT LA S É CURIT É A VERTISSEMENT : POUR R É DUIRE LES RISQUES DE FEU OU DE CHOC É LECTRIQUE, NE P AS EXPOSER CE PRODUIT À L ’ EAU OU À L ’ HUMIDIT É WARNING RISK OF ELECTRIC SHOCK. DO NOT OPEN MISE EN GARDE- WARNUNG- RISQUE DE CHOC É LECTRIQUE. NE PAS OUVRIR. ZUR VERMEIDUNG EINES ELEKTRISCHEN SCHLAGES GER ?[...]

66 Pr é cautions concernant la s é curit é A VERTISSEMENT Si l ’ on remarque une é mission de fum é e, d ’ odeurs suspectes ou de bruits provenant du projecteur , d é brancher la fiche du cordon d ’ alimentation de la prise de courant. • Ne pas continuer d ’ utiliser le projecteur dans ces cas, autrement cela peut entra î ner un in[...]

67 Nettoyer la fiche du cordon d ’ alimentation r é guli è rement afin d ’é viter toute accumulation de poussi è re. • Si de la poussi è re s ’ accumule sur la fiche du cordon d ’ alimentation, l ’ humidit é peut endommager l ’ isolant et entra î ner un incendie. D é brancher la fiche du cordon d ’ alimentation de la prise d[...]

68 Pr é cautions concernant la s é curit é Attention Pour d é brancher le cordon d ’ alimentation, tenir la fiche et non pas le cordon. • Si le cordon d ’ alimentation est tir é , le cordon sera endommag é et cela peut causer un incendie, des courts- circuits ou des chocs é lectriques s é rieux. D é brancher toujours tous les c â bl[...]

69 Pr é cautions pour la manipulation Pr é cautions pour le transport S ’ assurer absolument que le capuchon d ’ objectif est en place pour transporter le projecteur ou le d é placer. Le projecteur et la lentille de projection sont fabriqu é s avec pr é cision et, en tant que tels, sont sensibles aux vibrations et aux chocs. Pour transport[...]

70 Remplacement de la lampe Pr é cautions pour le remplacement de la lampe Retirez la fiche du cordon d ’ alimentation et assurez-vous que la section qui entoure la lampe est refroidie. Soyez prudent en manipulant la lampe source de lumi è re. La lampe peut é clater si elle est heurt é e par des objets solides ou si elle tombe à cause de la [...]

71 Proc é dure de remplacement de la lampe Mettez hors tension en suivant la proc é dure de la page 25, d é branchez la fiche é lectrique et v é rifiez que les é l é ments autour de la lampe ont refroidi. Assurez-vous que le ventilateur est arr ê t é . Pr é parez un tournevis Phillips à l ’ avance. Retirez la vis fixant le cache de la [...]

Projectors Panasonic Projector Systems Company Unit of Panasonic Corporation of North America One Panasonic Way, Secaucus, New Jersey 07094 PHONE: (201)392-6591 Technical Support: PHONE: (888)-411-1996 FAX: (201)348-7523 E-Mail: projectorsupport@us.panasonic.com Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010 ©[...]