Panasonic WJ-HD309 manual

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. WJ-HD309 Model Nos. WJ-HD316 Digital Disk Recorders Operating Instructions − ＋ TIMER ERROR ALARM RESET HDD 1 HDD 2 PULL ALARM ALARM SUSPEND OPERATE Digital Disk Recorder WJ-HD 316 MONITOR1 M ONITOR2 SHIFT DISK SELE[...]

2 The serial number of this product may be found on the top and bottom of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No. Caution: Before attempting to connect or operate this product, please r[...]

3 IMPORT ANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not use near any heat sourc[...]

4 CONTENTS IMPORTANT SAFETY INSTRUCTIONS ..................... 3 PREFACE .................................................................... 5 FEATURES .................................................................. 5 PRECAUTIONS ........................................................... 6 TRADEMARKS AND REGISTERED TRADEMARKS .................[...]

5 PREF ACE The Digital Disk Recorders WJ-HD316/309 are designed for use within a surveillance system and are a combination of a hard disk recorder and a video multiplexer (16-input for the WJ-HD316, 9-input for the WJ-HD309). The digital hard disk recorder is a recording device using a hard disk drive to record camera pictures instead of using vide[...]

6 PRECAUTIONS • Refer all work related to the installation of these products to qualified service personnel or system installers. • Do not operate the appliances beyond their speci- fied temperature, humidity, or power source ratings. Use the appliance at temperatures within +5 °C - +45 °C (41 °F - 133 °F) and humidity below 85 %. The input[...]

7 TRADEMARKS AND REGISTERED TRADEMARKS • Adobe, Adobe logos, and Acrobat are registered trade- marks of Adobe Systems Incorporated in the U.S. and/ or other countries. • Microsoft, Windows and Windows XP are registered trademarks of Microsoft Corporation in the U.S. and/or other countries. • Other names of companies and products contained in [...]

8 MAJOR OPERA TING CONTROLS AND THEIR FUNCTIONS ■ Front V iew S-VIDEO COPY 2 VIDEO OUT AUDIO OUT S-VIDEO COPY 2 VIDEO OUT AUDIO OUT [WJ-HD309] [WJ-HD316] ALARM TIMER HDD 2 ERROR HDD 1 ALARM SUSPEND ALARM RESET OPERA TE MONITOR1 MONITOR2 1 5 9 13 2 6 10/0 14 3 7 11 15 4 8 12 16 SEQ SHIFT OSD P AN/ TIL T STOP PLA Y PA USE REC - REC STOP ZOOM/ FOCUS[...]

9 When the shift button is lit, these buttons work as the toggled function buttons. (The buttons available as the toggled function buttons will light green when the shift button is lit.) !1 Pan, Tilt, Latest Recorded Image Playback Button (PAN/TILT, GO TO LAST) Pans/tilts a selected camera, or plays back the latest recorded image. (Refer to page 41[...]

10 q Audio Input Connectors (AUDIO IN 1 - 4) These connectors, for RCA pin jacks, accept an unbal- anced –10 dBV, 10 k Ω line input audio signal supplied from an external device such as a microphone amplifi- er. w Audio Output Connector (AUDIO OUT) This connector, for an RCA standard jack, supplies an unbalanced –10 dBV, 600 Ω line output a[...]

11 !1 PS·Data Ports (DATA) Connect PS·Data compatible devices with these ports. !2 Mode Switches (MODE) Set the operation mode of this unit with these dip switches. !3 RS485 Ports (RS485 (CAMERA)) Connect RS485 compatible combination cameras with these ports. !4 Network Port (10/100BASE-T) Connect this unit to a network compatible with 10BASE- T [...]

12 ■ On the Monitor 2 (T o display live or recorded image) Notes: • Same images displayed on monitor 2 will be displayed on the VGA monitor. • The camera title will be displayed with 16 characters (2 lines: 8 characters per line). Important: • Since the VGA output from this unit is the same as for televisions (720 H x 480 V pixels/vertical [...]

Delete Search Indicates that searching is currently being performed : Currently searching 13 ● Status on the T ask Bar • On the Main Bar q Status Display Area w Copy/Delete Icons e Live/Pla yback Time Displa y Area r Alarm Display Area t Error Display Area Recording Indicated Item Status Indication q Status Display Area Live Playback Indicates [...]

t Error Display Area Indicated Item Status Indication Error Warning Indicates an error occurrence or warning ALT-*: Alteration is detected W-ERROR: Failed to write data on the HDD SMART: Warning of the HDD malfunction H-METER: Set time for hour-meter (active time of the HDD) warning has passed THERMAL: The temperature inside the unit is too high PO[...]

Indicates the available disk space of each partition. Top: 100 % of the disk space is used (no avail- able disk space) Second from the top: 80 % of the disk space is used Center: 60 % of the disk space is used Second from the bottom: 40 % of the disk space is used Bottom: 20 % of the disk space is used Note: When "CONTINUE" is selected on[...]

16 z Insert the power plug to an outlet (AC 120 V, 60 Hz) Note: Make sure the power source is AC 120 V, 60 Hz. x Turn on the power switch on the rear panel. The OPERATE indicator will light and the system check (checking the system and hard disk) will start. The startup splash image below will be displayed on moni- tor 2 and the VGA monitor during [...]

17 CLOCK ADJUSTMENT It is recommended to check the clock periodically and put the clock right if it shows the wrong time. Adjust the clock when displaying a live image. z Press the SETUP/ESC button for 2 seconds or more. The SETUP MENU will be displayed on monitor 2 and the VGA monitor. x Move the cursor to "System" using the arrows butto[...]

18 SHUTDOWN To shutdown the unit, do the following. When recording is being performed, press the REC button for 2 or more seconds. Recording will stop and the indica- tor on the REC button will go off. When playback is being performed, press the STOP button. Playback will stop and the indicator on the PLAY/PAUSE button will go off. Turn off the pow[...]

19 When recording with higher priority than manual recording is performed, manual recording will not be performed until this recording finishes. Refer to the following about the recording mode. x Stop recording. Press the REC button down for around 2 seconds. The indicator on the button will go off and recording will stop. Notes: • The camera sel[...]

20 ● Recording Time Approximate possible recording durations will be as follows (with built-in HDD, manual recording): Recording with audio Unit: Hour EXA NQA FQA SFA Recording Rate [ips] (For Extended Recording) (Standard) (High Quality) (Highest Quality) 22 040 1 730 1 320 1 070 32 040 1 730 1 320 1 070 5 680 570 440 1 070 61 270 950 630 470 7.[...]

21 Record manually using an external switch at an emergency event occurrence. For example, install an external switch at the reception counter, and start recording with it when a suspicious indi- vidual appears. Refer to a system administrator about the required settings for emergency recording. z Press the external switch. The indicator on the REC[...]

22 It is possible to play recorded images without stopping recording. The playback images will be displayed on monitor 2 and the VGA monitor. z Select a camera respective to the recorded images to be played. (Go to step 2 if not neces- sary) Press the desired camera selection button. The pressed camera selection button will light green or blue and [...]

23 Fast forward/Fast reverse Rotating the shuttle ring will change the playback speed (1/2x, 1x, 2x, 5x, 10x, 20x) according to rotated degree. When the shuttle ring is held in the 20x position (rotated to the end) for 5 seconds, the play- back speed will be 50x. When the shuttle ring is held 5 more seconds after the playback speed became 50x, the [...]

24 Marking It is possible to play from a marked point. Do the following to mark a desired point. 1. Press the SHIFT button. The SHIFT indicator will light. 2. Press the camera selection button 12 (9 for the WJ-HD309) (MARK) at a desired point to be marked during playback. Up to 100 points can be marked. When more than 100 points are marked, the old[...]

25 Images from a camera will be recorded on the built-in hard disk or external recording devices (DVD-RAM drive, DVD-R drive or CD-R drive) connected to this unit. Available disk space or disks are as follows. Note: External recording devices can be used as a copy area for images recorded on the hard disk. It is impos- sible to record images on the[...]

26 c Move the cursor to select a disk to be played using the arrow buttons and rotate the jog dial to check the radio button next to the selected disk. Press the SET button to determine the selection. The recording event list window will be displayed. (Refer to page 28 for further information.) To close the DISK SELECT window, move the cursor to se[...]

27 It is possible to play recorded images from a designated time and date without stopping recording. Playback images will be displayed on monitor 2 and the VGA monitor. z Press the SEARCH button repeatedly until the time and date designation window is dis- played. The time and date designation window will be displayed on monitor 2 and the VGA moni[...]

28 There are 3 ways to search for a recorded image and play it. • Search for a recording event and play it (Recording event search) • Search for a motion detected time and date from recorded images and play it (VMD search) • Search for a marked point and play it (Marking search) Note: Playback images will be displayed on a single screen on mo[...]

29 Searching filter buttons: Selects the searching filter Filter cancel button: Cancels the selected searching filter and lists all recording events Time and date: <When searched by recording event> Time when recording started will be displayed. <When searched by VMD> Time when motion had been detected will be displayed. <When search[...]

30 z Press the SEARCH button repeatedly until the recording event list window is displayed. The recording event list window will be displayed on moni- tor 2 and the VGA monitor. Use the arrows button ( CD ) to switch displaying the list window and the thumbnail window alternately. To search using a searching filter, go to step 4. R 2 R LOGOUT MONIT[...]

c Filter recording events. Filter recording events by time and date Move the cursor using the arrows button and rotate the jog dial to enter time and date. Press the SET button to determine the entered time and date. The recording event in the entered time range will be listed and displayed. Filter recording events by camera channel Select camera c[...]

<Thumbnail window> 32 n To stop playback, press the STOP button. The indicator on the PLAY/PAUSE button will go off and playback will be stopped. Live images will be displayed on monitor 2 and the VGA monitor. Important: In the recording event list, start time of recording will be displayed. When events occurred successively, contents of the [...]

x Press the SET button. The VMD search window will be displayed. Enter a camera channel number and time range on the VMD search window for the VMD search. To search using the same conditions as the previous search, press the PLAY/PAUSE button. Go to step 12 when the VMD search is performed and a list of the results is displayed after the PLAY/PAUSE[...]

⁄0 Select the sensitivity using the arrows button ( DC ) from the following. OFF: Motion will not be detected LOW: Low sensitivity MID: Standard sensitivity HIGH: High sensitivity ⁄1 Rotate the jog dial to select "EXIT" on the sta- tus bar to exit from the motion detection area setup window. ⁄2 Press the SET button to display the VM[...]

35 ⁄3 Move the cursor to select a detection mode using the arrow buttons and rotate the jog dial to check the radio button next to the selected detection mode. Press the SET button to deter- mine the selection. Refer to page 36 for further information about each of the detection modes. <ANY AREA mode> Move the cursor to the parameter box us[...]

36 Any motion will be detected anywhere in the A, B, C, D areas. Note: In the ANY AREA mode, it is possible to set the masking duration. When the masking duration is set, motion will be ignored for a certain period (set duration as the masking duration) in the same area. It is conve- nient to set the masking duration to make the subject period shor[...]

37 ■ Searching for a marked point and play from that point (Marking search) Display the recording time of recorded images with a marked point in a list or a thumbnail and select the desired recording time to play. Refer to page 24 for further informa- tion about marking. z Press the SEARCH button repeatedly until the marking list window is displa[...]

38 MONIT OR LIVE IMAGES It is possible to display live images on a single screen or a multi-screen. On a single sequential display (It is also possible that dis- played images from cameras will be switched automatical- ly) ■ Displaying Live Images on a Single Screen z Press the MONITOR1/MONITOR2 button to select the monitor. When monitor 1 is sel[...]

39 ■ Displaying on a Multi-screen It is possible to display images on a multi-screen (4, 7, 9, 10, 13, 16 for the WJ-HD316, 4, 7, 9 for the WJ-HD309). z Press the MONITOR1/MONITOR2 button to select the monitor. When monitor 1 is selected, the indicator will light. When monitor 2 is selected, the indicator will not light. x Press the SHIFT button.[...]

40 ■ Sequential Display Displayed images from cameras will be switched automati- cally. Camera images will be displayed sequentially according to the settings performed in advance. z Press the MONITOR1/MONITOR2 button to select the monitor. When monitor 1 is selected, the indicator will light. When monitor 2 is selected, the indicator will not li[...]

41 CONTROL CAMERAS When displaying live images, the following camera controls are possible. • Panning/tilting: Moves a camera horizontally/vertically. • Zooming: Zooms in/out on images. • Focus: Adjusts the focus. • Iris: Adjusts the iris of the lens. • Preset action: Moves a camera to the preset position registered in advance. • Auto f[...]

42 ■ Iris Adjusts the iris of the lens. z Press the IRIS button. The IRIS indicator will light. x Use the arrows button ( AB ) to adjust the iris. To reset the set iris, press the SET button. ■ Preset Action Moves a camera to the preset position registered in advance. Important: • When using a camera of the WV-CS650 (WV-CSR650) series or the [...]

43 ■ Move a camera to the preset position z Press the PRESET/AUTO button. The PRESET/AUTO indicator will light and the PRESET/ AUTO PAN window will be displayed. x Press a camera selection button ([1] - [10/0] for the WJ-HD316, [1] - [9], [0] for the WJ-HD309) to select a desired preset posi- tion. Pressing the camera selection button [10/0] ([0][...]

44 Note: To move the camera to another registered preset position, press the SET button after selecting a desired preset position number in step 2. The PRESET/AUTO PAN window will not close and it is possible to select another preset number. ■ Auto Function (Auto Pan, etc) Moves a camera with an auto function set in advance. Important: When the m[...]

Event Action 45 ABOUT THE EVENT FUNCTION The event action will be performed when the following events occur. • Motion detection: When motion is detected by the motion detection function (see below), this is stated as an event of motion detection. • Video Loss: When a video signal supply is stopped because of a cable disconnection or malfunction[...]

46 ■ Alarm Function ● Blinks the ALARM indicator on the front panel ● Switches from the images displayed on monitor 1 and monitor 2 to the images from the location of the alarm occurrence (on a single screen) ● Displays the event information in the alarm display area on monitor 1 and the camera title display area on monitor 2 <Monitor 1&[...]

47 ■ Cancel the Alarm Action When an alarm has occurred, this unit will start the alarm action according to the selected alarm action mode. To cancel the alarm action, press the ALARM RESET but- ton. When "ON" is selected for "Alarm Auto Reset" (on the "Alarm Setup" menu of "Event"), the following will be p[...]

48 It is available to copy (duplicate) manually the recorded images in the copy area of the built-in hard disk to the external recording device (DVD-RAM disk, DVD-R disk, CD-R disk) connected to the unit. It is recommended to make back-up copies on a regular basis for unexpected situations such as malfunction of the hard disk. Manual copy is availa[...]

49 v Select the "OK" button using the arrows button and press the SET button. The DATA COPY window will be closed and data copy will start. The copy icon will be displayed on the task bar during copying. To close the DATA COPY window, select "CANCEL" using the arrows button and press the SET button. The setting will be canceled [...]

50 Perform the settings for the built-in hard disk of the unit, the optional extension unit and the DVD-RAM disk. These are the descriptions of how to delete recorded images on the hard disk and how to format a DVD-RAM disk. Refer to a system administrator for further information about the other disks. ■ Deletion of recorded images saved on the h[...]

51 b Move the cursor to "Manual Delete for Normal Recording Area" or "Manual Delete for Event Recording Area" using the arrows button, and set time and date using the jog dial. The images recorded the day before the set time and date will be subject to be deleted. n Move the cursor to "DELETE" using the arrows button a[...]

52 FORMA T (INITIALIZE) A DVD-RAM DISK To copy (duplicate) recorded images onto the DVD-RAM disk, formatting (initializing) the DVD-RAM disk is required in advance. To delete images recorded on the DVD-RAM disk, format- ting (initialization) of the DVD-RAM disk is also required. Important: All data on the disk will be deleted if formatted (initial-[...]

53 n Press the SET button to select "FORMAT". The confirmation dialog window will be displayed. m Move the cursor to "OK" using the arrows but- ton and press the SET button to start format- ting. To stop formatting, select "CANCEL" and press the SET but- ton. During formatting, the status window will be displayed. The [...]

54 DISPLA Y/EDIT TEXT INFORMA TION It is possible to attach text information to images when recording. Entering 20 characters for a line (up to 10 lines, with a total of 200 characters) is possible. These are the descriptions of how to display/edit the attached text information for images. Note: Displaying/editing text information is possible durin[...]

55 b Edit text information using the arrows button and the jog dial. • To insert a character Move the cursor to a desired point where a character is to be inserted using the arrows button, and select a character using the jog dial. • To delete a character Move the cursor to a character to be deleted using the arrows button, and press the STOP b[...]

56 Press the ALARM RESET button to can- cel the error or the warning status. Initialize the DVD-RAM disk. (Refer to page 52.) When initialized, all recorded data will be deleted. Press the ALARM RESET button to can- cel the error or the warning status. Replace the disk with new one. The DVD-RAM disk is almost full or com- pletely full. The CD-R or [...]

57 Indication The warning status will be canceled automatically after around 10 minutes of recovery. Contact the dealer. MEDIUM-n REMOVE FAN Warning Error Warning Press the ALARM RESET button to can- cel the warning status. Confirm that a disk has been inserted, or check the inserted disk format. Press the ALARM RESET button to can- cel the error s[...]

58 OPERA TION USING A SYSTEM CONTROLLER It is possible to operate this unit using a PS·Data compatible system controller. The following are the descriptions of how to operate this unit using the system controller WV-CU360C. To operate this unit using a PS·Data compatible system controller, perform the required settings in advance. Refer to a syst[...]

59 PLA Y PA USE REV –+ FWD Rotate the shut- tle ring Rotate the shut- tle ring During playback REV –+ FWD Rotate the shut- tle ring Rotate the shut- tle ring Rotate the shut- tle ring Rotate the shut- tle ring Rotate the shut- tle ring Rotate the shut- tle ring During playback REV –+ FWD During playback REV –+ FWD During playback REV –+ F[...]

60 Available only during pause Skip to the next frame Available only during pause Skip to the previous frame The point to be skipped to will be different between normal playback and filtered play- back. Skip forward The point to be skipped to will be different between normal playback and filtered play- back. Skip backward Available only during play[...]

It is possible to stop the sequential display by pressing a camera selection button. It is possible to stop the sequential display by pressing a camera selection button. Sequential display ON (For the WJ-HD316) Sequential display ON (For the WJ-HD309) SEQUENCE SEQUENCE SEQ 7 SHIFT + SEQ 4 SHIFT + Switches in the following order each time the button[...]

62 OPERA TION USING A PC It is possible to perform the settings or operate the unit using a web browser installed on a PC when this unit is connected to a network. The available features and the system requirements of a PC are as follows. Refer to the Network Operating Instructions (PDF) on the provided CD-ROM. ■ Features It is possible to operat[...]

63 1. Remove the rubber legs (6 pcs.) on the bottom of the unit. • Use a flat-blade screwdriver and remove the screws. 2. Install the rack mounting brackets on both sides of the unit. • Using the mounting screws (4 pcs.) for the rack mount- ing brackets, fix them firmly. 3. Install the unit in the rack. • Fix the unit firmly with the rack mou[...]

64 MANAGEMENT OF USERS/HOSTS It is necessary in advance to register users and PCs (hosts) who access this unit via a network such as LAN. Up to 32 users and 8 hosts can be registered. The following information can be registered as user information and host information. For the set items above, the unit will work differently depending on whether the[...]

65 Notes: • When a user is operating this unit using a PS·Data compatible controller, this user can log in automatically as a PSD user set for "PSD User" of "System" on the SETUP MENU. • When a user logged in this unit using a PS·Data compatible controller and didn’t operate the unit for around 2 minutes, this PSD user w[...]

66 OPERA TING THE UNIT FOR THE FIRST TIME Important: When connecting an optional extension unit (the WJ- HDE300 series), turn on the power of the extension unit before turning the power of this unit on. z Turn on the POWER switch. x Press the SET button during the system check complete window is displayed. The HDD DISK MENU window will be displayed[...]

67 Preparation for maintenance (HDD replacement, installation, etc.) When maintaining (HDD replacement, installation, etc.) without turning the power of the unit off, carry out the follow- ing operation after setting the HDD SAFETY MODE to ON. (The default setting is ON.) This can be set on the "Disk Info" menu of "Maintenance".[...]

68 When the system check has been completed, the HDD SAFETY MODE window (as shown below) will be displayed. The camera selection buttons on the front panel (1 - 16 for the WJ-HD316, 1 - 9, 0 for the WJ-HD309) will light green and orange (for 2 seconds each) alternately. Move the cursor to OFF using the arrows button and press the SET button. The un[...]

69 ■ Connections when the unit is used independently An example of connections is shown below when the unit is used independently. Important: • The power plug should be connected last. • When connecting combination cameras , connect them to the video input connectors 1 - 8 when using the WJ-HD316 or 1- 6 when using the WJ-HD309 (for coaxial c[...]

70 ■ Connections with an extension unit An example of connections is shown below when the unit is used together with an optional extension unit. This unit can be connected with up to seven extension units. Connect the EXT IN port on the rear panel of the extension unit and the EXT STORAGE port on the rear panel of this unit using the cable provid[...]

71 ■ Connections with DVD-RAM, CD-R, and DVD-R drives This is an example of connection when the unit is used together with the designated DVD-RAM, DVD-R and CD-R drive. Connect the designated DVD-RAM, DVD-R and CD-R drive and the COPY1 port on the rear panel or the COPY2 port inside the connectors cover on the front panel of this unit using an US[...]

72 ■ Connections with the VCR When it is necessary to copy the recorded images to a video tape using a VCR, connect the VCR to the S-VIDEO connector (or the VIDEO OUT connector) and the AUDIO OUT connector inside the connectors cover on the front panel of this unit as below. Note: The same video signal supplied to the MONITOR1 connector and to th[...]

73 ■ Connections with PS·Data systems This is an example of connection when the unit is used together with the PS·Data devices. If a connected system controller is PS·Data compatible, it is possible to operate this unit or connected devices using the sys- tem controller. Use the RS485 cable provided with the system controller. Important: • T[...]

74 ● When this unit is connected with the system device (when this unit is used as a controller) POWER ON OFF ALARM Data Multiplex Unit WJ-MP204 ALARM SUSPEND 1234 ESC SET RESET SUSPEND SET UP ALARM UNIT 0 9 8 7 6 5 4 3 2 1 System Controller Controller Te r mination: ON Unit Address : 2 RS485 cable Mode switch (No.8 : OFF) Coaxial communication u[...]

75 ■ Cascade connection of multiple units Up to of four units can be connected. For the cascade connection, connect the CASCADE IN connector and the CASCADE OUT connector on the rear panel of each unit as below. Important: • When connecting the unit in the cascade connection, set "Cascade" of "PS·Data Setup" in "Comm&q[...]

76 ● When the PS·Data compatible device is connected to the first unit (when this unit is used as a receiver) 1 2 IN OUT CASCADE OUT 16 16 3 15 15 14 14 13 2 1 13 12 12 11 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 VIDEO AUDIO IN AUDIO OUT MONITOR OUT CASCADE IN MONITOR (V GA) ALARM/CONTOR OL SERIAL ALARM POWER COPY 1 MODE EXT STORAGE 10/100BA[...]

77 ● When the PS·Data compatible device is connected to the third unit (when this unit is used as a receiver) 1 2 IN OUT CASCADE OUT 16 16 3 15 15 14 14 13 2 1 13 12 12 11 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 VIDEO AUDIO IN AUDIO OUT MONITOR OUT CASCADE IN MONITOR (V GA) ALARM/CONTOR OL SERIAL ALARM POWER COPY 1 MODE EXT STORAGE 10/100BA[...]

78 ● When the PS·Data compatible devices are connected to the first and third units (when this unit is used as a receiver) 1 2 IN OUT CASCADE OUT 16 16 3 15 15 14 14 13 2 1 13 12 12 11 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 VIDEO AUDIO IN AUDIO OUT MONITOR OUT CASCADE IN MONITOR (V GA) ALARM/CONTOR OL SERIAL ALARM POWER COPY 1 MODE EXT STO[...]

79 ■ Connection with the RS485 camera This is an example of connection when the unit is used together with the RS485 devices. Up to eight cameras can be connected using a single RS485 (CAMERA) port. Important: • Terminate both devices on both ends of the connection. Refer to the respective operating instructions for the descriptions of how to t[...]

80 ● Daisy connection Multiple cameras can be connected to the RS485 (CAMERA) port. Example: When cameras 1 - 4 are connected to one of the RS485 (CAMERA) port and cameras 9 - 12 are connected to the other RS485 (CAMERA) port. 1 2 IN OUT CASCADE OUT 16 16 3 15 15 14 14 13 2 1 13 12 12 11 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 VIDEO AUDIO IN[...]

81 ■ Mode Switch RS485 interface is used to communicate between this unit and the PS·Data compatible system device. In this case, it is neces- sary to terminate both devices on both ends of the RS485 connection. The settings of the mode switch will be different depending on whether this unit is used as a receiver or a controller. When an RS 485 [...]

@5 Pin No. 82 ■ How to Use the T erminals of the ALARM/CONTROL Connector These terminals are used for emergency recording, auto time adjustment (Auto Adjust Time), taking measures against power outages (Shutdown Time), and when installing a buzzer, a lamp, or similar alarm device. They are also used to synchronize with the sequential display chan[...]

83 ● Connection for emergency recording When the external switch is turned ON, emergency recording will be started. Resolution, recording time, recording rate and quality for emergency recording can differ according to the settings of "Emergency REC" of "Recording" on the SETUP MENU. (Refer to page 98.) ● Connection for exte[...]

84 ● Connection for the Auto Adjust Time function • When "Auto Adjust Time" of "System" on the SETUP MENU is set to "MASTER" "Time Adjust Output" becomes available and the clock of this unit can be applied to other units. • When "Auto Adjust Time" of "System"on the SETUP MENU is set [...]

85 ● Connection with the Uninterruptible Power System (UPS) This is an example of connection with the uninterruptible power system (UPS) to be installed to protect from a power outage. When a signal is supplied to the outage detection I/O terminals from the uninterruptible power system (UPS), internal process- ing (stops recording safely) will be[...]

■ How to Use the T erminals of the ALARM Connector These terminals are used to connect the alarm devices, such as sensors, door switches, etc. The pin configurations of these terminals are as shown below. The connector used should be compatible with the pin configu- ration. Pin Configuration The pin array is different from other disk recorders. M[...]

87 ● Alarm connection When a signal is supplied to the alarm input terminals of CH 1-16, recording and displaying of camera images will be per- formed according to the settings. When an alarm device such as a buzzer, a lamp, etc., is installed outside, connect them to the alarm output terminals (pin nos. 9 - 12, pin nos. 23 - 25) or to the alarm [...]

88 ■ How to Use the SERIAL Connector This connector is compliant with the RS232C Standard, and is used to communicate with a connected PC. A connection example and the pin configuration of the SERIAL connector are as shown below. Important: • When using the SERIAL connector, it is necessary to perform the settings with "RS232C Setup" [...]

89 SETUP To operate this unit, it is necessary to set each item of the SETUP MENU in advance. Perform the settings for each item of the SETUP MENU by displaying the SETUP MENU on monitor 2. Settings items are as below. ■ Item list of the SETUP MENU Maintenance REC Rate Display the recording rate for each recording mode and image quality for each [...]

90 Switcher Monitor1 Perform the settings for the image switching on monitor 1 such as the setting of the sequential display or the screen to be displayed at login on monitor 1. Monitor 2 Perform the settings for the image switching on monitor 2 such as the setting of the sequential display or the screen to be displayed at login on monitor 2. Displ[...]

91 Main menu: These menus are always displayed on the SETUP MENU. Live image: Live images from the camera channel that was selected just before the SETUP MENU was displayed. Main area: The setting items of the selected submenu will be displayed in this area. Submenu: The submenu of the selected main menu will be displayed on the left side of the SE[...]

92 z Press the SETUP/ESC button for 2 seconds or more when displaying live images. [Screenshot 1] The top page of the SETUP MENU will be displayed. x Select a main menu using the arrows button and press the SET button. [Screenshot 2] The submenu of the selected main menu will be displayed. c Select the submenu using the arrows button ( CD ) and the[...]

93 Perform the settings for the hard disk drives. It is possible to check the histories (log) of event occur- rence, error occurrence and access. q [REC Rate] Check the recording rate and the image quality for each camera channel. Recording rate for each recording mode for each cam- era (as shown below) will be displayed in list form. MANU: Manual [...]

94 r [Disk End Mode] Set actions to be taken when the available hard disk space has run out Select an action from the followings to be taken when the available space of the built-in hard disk (normal recording area, event recording area, copy area) or the external recording device (DVD-RAM, CD-R or DVD-R disk drive) connected to the copy port (COPY[...]

95 u [Event Log] Check the event log Event log (time and date at an event occurrence, details) will be displayed in list form. Refer to page 45 for further information about each event. COM: Command alarm EMR: Emergency recording LOSS: Video loss TRM: Terminal alarm VMD: Motion detection Note: Up to 750 event logs can be kept. When more than 750 ev[...]

SMART X-Y X indicates the unit/unit number that has the hard disk error Y indicates the unit/unit number HDD SMART error 96 o [Access Log] Check the access log The time, user name and IP addresses when logging in/out to/from this unit will be displayed in list form. **IN: The user name or the IP address displayed before IN indicates the user/host l[...]

97 Perform the settings for the basic recording (REC Setup) and the emergency recording. q [REC Setup] Perform the settings for the basic recording. Perform the following settings for the basic recording. • [Recording] Select ON or OFF to record or not record. ON: Recording will be performed. OFF: No recording will be performed. Important: When O[...]

98 • [Audio Allocation] Allocates audio from the audio input connectors (1 - 4) on the rear panel of the unit to camera channels. Allocate audio in accordance with channels of connect- ed cameras. When OFF is selected, audio will not be heard. Important: • When a live image from the audio assigned camera channel is displayed on a single screen [...]

99 Perform the settings for event actions of each event type (motion detection, video loss, command alarm and terminal alarm). q [Event Setup] Settings for the alarm output duration and the buzzer duration Perform the settings for the alarm output duration and the buzzer sound duration for each event type (motion detection, video loss, command alar[...]

100 z Rotate the jog dial to select ON for a desired camera channel for which the motion detection function is to be applied, and press the SET button. [Screenshot 2] The "VMD Setup" window will be displayed. x Rotate the jog dial to select "SETUP AREA" on the status bar. Note: To set all areas on the monitor as the motion detec[...]

101 x Move the cross cursor onto an area to be deleted using the arrows button and press the SET button. c To complete the settings, rotate the jog dial to select "EXIT" on the status bar. → The "VMD Setup" window will be closed. ● Set the sensitivity Set the sensitivity for the created motion detection area. Sensitivity can[...]

102 <DURATION> Move the cursor to the parameter box of each area using the arrows button ( B ) and select a moving dura- tion for an object in each area from the following using the arrows button ( DC ). --/5 s/10 s/20 s/30 s/40 s/50 s/1 m c To complete the settings, rotate the jog dial to select "EXIT" on the status bar, and press [...]

103 •[ A l arm Auto Reset] The following are possible for the alarm auto reset. When OFF is selected, the alarm display will not auto- matically disappear. To erase the alarm display, press the ALARM RESET button. OFF/1 s - 30 s (in 1 second intervals) 40 s/50 s/1 m/2 m/3 m4 m/5 m • [Alarm Disarm] The following are possible for the alarm disarm[...]

Perform the settings for the recording schedules of record- ing and event action by designating a day of the week and time. A day can be divided into up to 6 time zones, and record- ing programs and event action programs can be assigned to each time zone to create a recording schedule. Up to 4 normal recording programs (REC Program) and up to 4 eve[...]

105 ● Recording Rate and Image Quality for Each Camera Channel Perform the settings for recording rate, image quality and recording duration for each camera channel (only for event pre-recording and event post-recording). Perform the settings for each recording mode. Assign the recording rate for each camera channel as described in "Recordin[...]

106 w [Event Program] Create event programs for an event occurrence Perform the settings of event action for each event type (motion detection, video loss, terminal/command alarm) or of auto copy. ● VMD Perform the settings of event action at a motion detection or the settings of the auto copy function. Perform the settings for the following oper[...]

[Screenshot 1] Start operation after displaying the timetable window. z Press the SET button. [Screenshot 2] The pop-up setting menu of the timetable for every day of the week will be displayed. The cursor will be displayed and will move to "MON" (Monday). x Select a day of the week using the arrows button ( CD ) and press the SET button.[...]

, Rotate the jog dial to select a desired REC program/ Event program. (Rotating the jog dial changes the displayed REC pro- gram.) REC progam will be displayed with different colors. Orange: REC program 1/Event program 1 Yellow: REC program 2/Event program 2 Pale purple: REC program 3/Event program 3 Indigo blue: REC program 4/Event program 4 Repea[...]

109 Perform the settings for image switching such as the sequential display setting or the waiting screen (while log- ging out) setting for displaying on monitors 1 and 2. q [Monitor 1] Switcher function of monitor 1 Perform the settings for the switcher function of monitor 1. ● Live Sequence Perform the settings for the sequential display of liv[...]

110 ● Auto Skip Select ON of OFF to determine whether or not to skip the camera channel without supplying the video input signal because it is not connected, etc. ON: Skips a channel if it is not connected. OFF: Displays a black screen for a channel not connected. ● Login Screen Select a camera image to be displayed during the login procedure f[...]

111 w [Monitor 2] Switcher function of monitor 2 Perform the settings for the switcher function of monitor 2. ● Live Sequence The settings for "Live Sequence" are the same as for "Monitor1". Refer to page 109 for further information. ● Sequence Timing The settings for "Sequence Timing" are the same as for "Mon[...]

[Screenshot 2] The camera title pop-up window will be displayed. x Move the cursor to "CAM1" using the arrows button. [Screenshot 3] The cursor moves to " CAM1". c Select a character to be entered by rotating the jog dial. Up to 16 characters can be entered. v Move the cursor to the right side of the entered charac- ter using th[...]

113 3. Move the cursor to "OK" using the arrows button and press the SET button. The camera title will be copied. • The following characters can be entered for a cam- era title: 0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z À Ä Â Æ Ç É Ì Ñ Ò Ö Ù Ü [...]

114 ● Camera Title Display Select ON and OFF whether or not to display the camera title. ON: Displays the camera title. OFF: Does not function. ● Alarm Display Select ON and OFF whether or not to activate the alarm dis- play at an event occurrence. ON: Displays the alarm display at an event occurrence. OFF: Does not function. e [Monitor2] Setti[...]

115 It is necessary to adjust the communication speed and use the same communication protocol with external devices such as a controller when connecting those external devices to the DATA port or the SERIAL connector (RS232C). It is also necessary to perform the settings for the network such as the IP address and the gateway address when operating [...]

116 ● Baud Rate Select the communication speed for data transmission with a connected device from the following. 2 400/4 800/9 600/19 200/38 400 bps ● Data Bit It is impossible to change the value for this setting. 8 bit ● Parity Select a method to check a transmission error at communi- cation from the following. NONE: No parity check EVEN: E[...]

117 ● Baud Rate Select the communication speed for data transmission with a connected device from the following. 4 800/9 600/19 200 bps ● Control Camera CH It is possible to assign camera channels to the RS485 ports 1 and 2 as shown below. [Screenshot 1] Start operation from the "RS485 Setup" menu. z Move the cursor to "Control C[...]

118 ● Data Bit Select a data length for communication from the following. 7/8 bit ● Parity Select a method to check a transmission error at communi- cation from the following. NONE: No parity check EVEN: Even parity ODD: Odd parity ● Stop Bit Select a stop bit from the following. 1/2 bit ● Retry Timing Select a retransmission interval for w[...]

119 ● DNS Select "MANUAL" or "AUTO" to enable searching an IP address by its host name using DNS. When "OFF" is select- ed for "DHCP" (no use of the DHCP server), select "MANU- AL" and enter the domain name and the DNS server address. If "ON" is selected for "DHCP" (use of the [...]

120 Perform the following system settings required to operate this unit. q [Basic Setup] Basic system settings Perform the following settings for basic operation. ● ADMIN Password Set the password for an administrator. Enter 4-32 alphanumeric characters. The same method is used to enter, insert and delete char- acters as for attaching text inform[...]

121 ● Auto Copy ON or OFF whether or not to copy recorded images to the copy area on the hard disk automatically. OFF: Does not copy automatically. ON: Copies recorded images to the copy area on the hard disk of this unit. Important: • When OFF is selected, the auto copy function at an event occurrence and emergency recording will not function.[...]

122 [Screenshot 2] The "Summer Time (Day Light Saving) Table" will be dis- played. x Move the cursor to enter the ON or OFF time (year, month, date) for summer time using the arrows button. [Screenshot 3] The cursor will move to the selected cell for entry of the ON or OFF time for summer time. c Rotate the jog dial to enter the ON or OFF[...]

123 y [Host Registration] Registration of PC (host) accessible to this unit Register host information for the PC that accesses the unit via a network such as a LAN. Move the cursor to "SET" at the lower right on the menu and press the SET button to complete registration. ● Host IP Address Enter the IP address. Move the cursor to "H[...]

124 16 SCREEN (only for the WJ-HD316): Displays images on a 16-split screen. SEQ: Images will be displayed in the sequential display. ● Camera Partitioning Select a controllable range for each camera channel from the following. View/Operate: Displaying live images and operating cam- era are possible. View: Displaying live images is possible but c[...]

125 Alarm Reset Alarm Suspend Copy Normal Recording Erase Event Recording Erase Manual REC Operation Playback Operation N/W Access An event operation can be canceled. (Refer to page 47.) An event operation can be suppressed. (Refer to page 47.) A recorded image can be manually copied. (Refer to page 48.) Image data in the normal recording area of t[...]

126 For operating the camera connected to this unit, it is necessary to set the camera function in advance. Setup of camera function can be performed on the setup menu of the connected camera. You can operate the camera setup menu by calling up it from this unit. Contents of the camera setting menu and operations vary according to the connected cam[...]

127 DISK MANAGEMENT ■ Notes on hard disk Camera images are recorded into the built-in hard disk of this unit. There are two hard disks in this unit. In case one of them malfunctions during recording, it is possible to keep record- ing with the other hard disk (mirror function). The internal hard disk of this unit is virtually divided into areas 4[...]

128 2. Remove the cable from the front panel. 3. Remove the screws fixing the mounting unit, and then pull the mounting bracket toward you. 4. Remove the screws fixing the hard disk drive. First, remove the four screws fixing the upper side of the hard disk drive while holding the bottom side of the hard disk drive to prevent the hard disk from fal[...]

129 When replacing the hard disk drive without turning off the power of the unit. z Close the SETUP MENU after selecting "ON" for "HDD Safety Mode" of "Disk Info" on the "Maintenance" menu. → The HDD SAFETY MODE window will be displayed. x The procedures are different between the replacement of the hard dis[...]

130 160 GB: Indicates the hard disk capacity (disk existed when last started up) 160 GB M: Indicates the hard disk capacity (mirrored disk existed when last started up) ADD (160 GB): Indicates that this hard disk is newly mount- ed at this startup, but that it was not mounted last time. Those parenthesized numbers indicate the capacity of the hard [...]

131 Summary of the RAID 5 function (Redundant Arrays for Independent Disks, independent data disks with distributed parity blocks) It is possible to use the RAID 5 function with an optional extension unit. RAID level 5 regards 3 or more drives as one drive, and it is possible to read data by attaching error correction data even though one of the dr[...]

132 ■ Formatting (Initialization) the Hard Disk It is necessary to initialize the hard disk in the following cases. • When replacing the hard disk of this unit •W hen operating the unit for the first time after connect- ing the optional extension unit to this unit Important: When the hard disk is formatted (initialized), all of the recorded i[...]

133 , Press the SET button after setting. [Screenshot 5] The confirmation dialog window will be displayed. . Move the cursor to "EXECUTE" using the arrows button ( A B ) and press the SET button. → Formatting will start and the format result dialog window will be displayed. The "TOP MENU" of the "HDD DISK MENU" will [...]

134 [Screenshot 4] The "DISK SELECT" menu will be displayed. When using the RAID 5 function, the "UNIT SELECTION" menu will be displayed. <Screen displayed when using the RAID 5 function> m Move the cursor to a desired hard disk (unit) to be for- matted (initialized) using the arrows button and press the SET button. [Scree[...]

135 [Screenshot 7] The "PRE RECORDING AREAS" menu will be displayed. ⁄0 Select the camera channel for pre-recording using the arrows button and assign the disk space to the select- ed pre-recording area by rotating the jog dial. Repeat this operation to assign disk space to two or more camera channels. Press the SET button after setting[...]

136 Mirroring is the function that records camera images onto two hard disks simultaneously. In case one hard disk has a problem, image data will be stored on the other hard disk. The credibility of disk can be enhanced. It is recommended to activate the mirroring function for the first use of this unit. When the mirroring function is activated wit[...]

137 n Select a recording area using the arrows button and assign the disk space to the selected recording area by rotating the jog dial. Repeat this operation to assign disk space to two or more recording areas. Press the SET button after setting. m Press the SET button after setting. [Screenshot 5] The confirmation dialog window will be displayed.[...]

138 [Screenshot 1] The "TOP MENU" of the "HDD DISK MENU" will be dis- played. x Move the cursor to "MIRROR ON" using the arrows but- ton ( A B ) and press the SET button. Note: When it is impossible to recover the hard disk (mirror on) such in case that the hard disk size to be recovered is too small, it is impossible [...]

139 c Enter the password for an administrator by rotating the jog dial. The camera selection buttons ([1] - [10/0] for the WJ- HD316, [1] - [9], [0] for the WJ-HD309) are available to enter numbers for password. The same method is used to enter, insert and delete characters as for attaching text information to images. Refer to page 54. → The hard[...]

140 ■ SERIAL (RS232C) Communication Protocol With the SERIAL (RS232C) interface, you can control functions of this unit by transferring the specified commands from a per- sonal computer (PC) to this unit. Notes: • This unit does not support the communication converted between the SERIAL (RS232C) and USB interface. • When controlling the unit [...]

141 • When an ANSWER command is required The unit sends back the status or data, as shown in the figure. • About ACK code After receiving an command from the PC, the unit sends back the ACK code to the PC in 20 ms or less. [ACK] = Reception succeeded (ASCII code: 06H) After the ACK code sending back and the command processing has completed, the[...]

142 • Parameter error When the unit cannot properly process the received command, the unit sends back an error code to the PC. After clearing the receive buffer, the unit enters the wait state until receiving the following [STX] command. • If the unit receives another command during the response, the unit will respond to the command after proce[...]

143 1 2 IN OUT CASCADE OUT 16 16 3 15 15 14 14 13 2 1 13 12 12 11 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 VIDEO AUDIO IN AUDIO OUT MONITOR OUT CASCADE IN MONITOR (VGA) ALARM/CONTOROL SERIAL ALARM POWER COPY 1 MODE EXT STORAGE 10/100BASE-T RS485(CAMERA) D ATA AC IN SIGNAL GND 1 4 2 D-sub Pin 9 (Female) D-sub Pin 9 (Female) This unit P ersonal c[...]

144 Basic Operation Item Forward a field Rewind a field Pause during playback Play Manual recording Manual recording with text Stop Skip & play forward Skip&play reversely Record No. Search and playback Time & date search and playback Record skip LISTED Playback Playback latest image A - B repeat playback Display COPY SETUP MENU Display[...]

145 Item Start sequence Stop sequence Disk selection Marking Alarm Control Item Alarm input Alarm input with text Alarm reset Alarm suspension Alarm change information (LED indication) Alarm change information Setup Control Item Display SETUP MENU Transmission command (ASCII) MSU:n DCR:n1n2 TSU:yyyymmddhhnn MST:n MRM:n Response command (ASCII) MSU:[...]

146 Data Control Item Copy by specifying record Copy by specifying date & time Data copy completed Cancel data copy Erase log Log data total number inquiry Log readout Record list acquisition Text acquisition Text writing Disk End Notification Item Disk end auto-notification setting Disk end auto-notification Transmission command (ASCII) MDE:n [...]

147 Search Operation Item Display search editing area Display Operation Item Switch display Inquiry Item Additional disk space inquiry ID request Interface ID request Production category request Alarm information request Software version inquiry Status inquiry Transmission command (ASCII) Transmission command (ASCII) QHR:p QID QIB QIC QLD:0 QRV QSR[...]

148 zqm: Monitor status: camera CH: Playback time Monitor status n=0 Live n=1 Live sequence n=2 Playback n=3 Other statuses Camera CH Playback time: yyyymmddhhnnss ztl:n Search editing area ON n=0 Search editing area OFF n=1 Recording event search list ON n=2 Recording event search thumbnail ON n=3 VMD search list ON n=4 VMD search thumbnail ON n=5[...]

149 Communication Item Communication check Transmission command (ASCII) RCK Response command (ASCII) RCK Parameter (ASCII) Record information inquiry ZGP:rrrrrrrrrrrrrrrr ZGP:rrrrrrrrrrrrrrrr: ccc:q:nnnn:yyyymmdd hhnnss:nnss:t:ssssss rrrrrrrrrrrrrrrr: Record number ccc: Camera CH q: picture quality (0 (Very Fine), 1 (Fine), 2 (Normal), 3 (Extended)[...]

150 FLOWCHART OF THE SETUP MENU Recording Emergency REC Recording REC Setup Maintenance REC Rate Maintenance Disk Info Maintenance V ersion info Maintenance Disk End Mode Maintenance Disk Capacity Maintenance Disk Delete Maintenance Error Log Maintenance Access Log Maintenance Event Log Event Event Setup Schedule Time T able Maintenance Monitor 1 D[...]

151 P ARAMETERS AND THE DEF AUL T SETTINGS OF THE SETUP MENU These are the setting parameters and the default settings of the items on the SETUP MENU. Refer to these as reference. Maintenance Disk Info Warning for Disk Life Time 10 000 h/20 000 h/30 000 h 30 000 h HDD Safety Mode ON/OFF OFF Disk End Mode Normal Recording Area CONTINUE/STOP CONTINUE[...]

152 Setup Menu Setup Item Parameter Default Setting Event Event Setup Alarm Output OFF/1 s/2 s/...../30 s/40 s/50 s/1 m/ 2 m/...../5 m/EXT VMD: OFF Video Loss: 2 s Terminal Command Alarm: 2 s Output Terminal HD316: TRM1/TRM2/...../TRM16 HD309: TRM1/TRM2/...../TRM9 Buzzer OFF/1 s/2 s/...../30 s/40 s/50 s/1 m/ VMD: OFF 2 m/...../5 m/EXT Video Loss: 2[...]

153 Setup Menu Setup Item Parameter Default Setting EVENT PROGRAM Action Mode (The unit) ALARM/ACT DET ALARM REC CH ON/OFF ON Auto Copy ON/OFF OFF Preset Position --/1/2/...../64 -- Serial Notice ON/OFF OFF Mail Notice ON/OFF OFF FTP Alarm Sending ON/OFF OFF Special Days DATE 1/1 to 12/31 -- Mode MON/TUE/WED/THU/FRI/SAT/SUN -- Switcher Monitor1 Liv[...]

154 Setup Menu Setup Item Parameter Default Setting Com Camera Control COMP S/M/L HD316: CAM1to CAM8: S HD309: CAM1 to CAM6: S TYPE HD316: CAM1 to CAM8: COAX/RS485/OFF, HD316: CAM1 to CAM8: COAX, CAM9 to CAM12: RS485/PSD/OFF, CAM9 to CAM12: RS485, CAM13 to CAM16: RS485/PSD/OFF CAM13 to CAM16: RS485 HD309: CAM1 to CAM6: COAX/RS485/OFF, HD309: CAM1 t[...]

155 Setup Menu Setup Item Parameter Default Setting Network SNMP COMMUNITY - public Setup CONTACT - - SYSTEM NAME - - LOCATION - - NTP Setup Time Adjustment ON/OFF OFF Time Zone GMT-12:00/GMT-11:00/...../GMT-4:00/GMT-3:30/ GMT-3:00/...../GMT-1:00/GMT 0:00/GMT+1:00/ GMT+2:00/...../GMT+9:00/GMT+9:30/ GMT+10:00/...../GMT+13:00 GMT-5:00 NTP Server Addr[...]

156 Setup Menu Setup Item Parameter Default Setting Time & Date Date Format YY.MM.DD/MMM.DD.YY/DD.MMM.YY MMM.DD.YY Time Format 24 h/12 h 12 h Auto Adjust Time ON/OFF OFF Master Time 0:00/1:00/...../23:00 0:00 Summer Time(Day Light Saving) ON/OFF/AUTO OFF Summer Time(Day Light Saving) Table - - User Regist. User Name - - User Edit Password - - U[...]

157 • Check if the power is supplied to cameras and connected devices. • Check if the power plug is surely connected to the AC out- let. • Check if the power cord is surely inserted into the power socket of the unit. • The HDD SAFETY MODE is set to ON. In this case, set the HDD SAFETY MODE to OFF. • Check if the lens covers of the cameras[...]

158 • Check if the HDD has an available disk space. • Check if the recording setup is set to ON. • Check the schedule settings. • Check the recording priority settings. • When the setting menu is displayed by non-interlace sig- nal, the setting menu may be unable to function normally. Since the setting menu of the matrix switcher is displ[...]

159 Check item/Remedy Problem Page Alarm operations are not acti- vated. "VIDEO LOSS" appears on the monitor. "THERMAL" appears on the monitor. The clock does not keep cor- rect time. When you power on the unit, HDD DISK MENU is displayed. • Check if alarm input signals are properly input to the ALARM or ALARM/CONTROL at the r[...]

• Check the host registration setting. When host authentica- tion is set to ON, you cannot establish the connection from computers other than the PC registered as the host. 160 Check item/Remedy Problem Page The additional disk space of HDD is not displayed. The available disk space of HDD is not displayed on the right bar. Cannot establish the c[...]

161 General SPECIFICA TION Power source: Power consumption Ambient operating temperature Ambient operating humidity Dimensions Weight Input/Output Video Audio Others * 1 When power is not supplied, video output signal was not sent from the unit even if video input signal is supplied. * 2 Non-voltage N.O. Contact, 100 mA, +5 V pull-up * 3 Open colle[...]

162 ST ANDARD ACCESSORIES CD-ROM* ............................................................................ 1 Operating Instructions (this manual) .................................. 1 Warranty ............................................................................. 1 The following are for installation: Power Cord ...........................[...]

163[...]

PANASONIC CANADA INC. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 PANASONIC SALES COMPANY DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC. San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina, P.R. 00985 (809)750-4300 Panasonic Digital Communications & Security Company Unit of Matsushita Electric Corporat[...]