ParaBody 950102 manual

Serious Steel 950 ST 9501.02 ASSEMBLY INSTRUCTIONS Part # 6705001 P, zv~on: 08104197[...]

! ! ! ATTENTION ! ! ~ UNLE,:,S 0 THER WISE SHOWN, z~LL CONNECTIONS WILL CONSIST OF ONE 1~ ~o~ ~; two ~N~ ONF~ a),,gOC~N~r. BOLT ~ LOCKNUT NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE ~ .OF THE BOLT. ~/i////i~ BOLT LENGTH BOLT LENGTH RULER: 1/2 ] 1/2 .. I 3 4 1/2 1/2 I 5 6[...]

950 ST Parts List KEY 2 3 4 5 6 7 ’9 ’11 12 13 14 15 ~6 17 18 19 2O 21 ~ 23 24 26 27 28 29 30 31 32 34 36 36 37 ’38 39 "40 41 42 43 ’45 46 47 48 "49 50 51 52 53 54 "55 56 57 58 "’69 PART. # DI-’$CRIPTION 6623603 PF~ESS’ WT STACK BASE WHT 6624202 ;BACK PAD ANGLE LEFT BLK 6624302 BACK PAD ANGLE’ RIGHT BLK 6622903 P[...]

Frame Assembly Instructions Use th~s procedure to assemble the frame of the ParaBady 950ST ~ .~t/8" X 4’ NUT X 3" I~rtLT ~ Step A. I Loosely assembler the leg we|~ht base (18) and the press weight stack base (1~, to 1’he base (15) using two 1/2 x 5-1/2 bolts (91), four 1/2" washers(79), and two 1/2’ nyl¢)ck nuts shown. Apply t[...]

Step 2 ’ A. Securely assemble the f!,oatln~ p.ulle.y stop (3.2~, and the s.eaf, support (33). to the front ~,prlght (31) using two 1/2 x 4-,1/2 bolts (.gO), four 1/Z~ washers (~79), and two 1/2" nylock nuts (82). e. Securely assemble one 3/6" spring pin (62) to the seat support (33) as shown. C. Securely a~tach one seat pad (45) to the [...]

2-314"[...]

)3/8 X 3" Step 4 A. urel attach the press ~ase (13) to the base (15) using ~wo IlZ x.3-~I/4" bolts (!19;~ tw~,.11z" the rear upright (~21) using one ;~/o bol~ wasne~ L{=~ ,~"= "7- "~o~ ~.~ --e 3/B nylocK nut (B3). (95), tWO 5/B washers L~o) ....... Securely assemble one 3/B" spring pin (62) to ~he wolff sleeve (39[...]

Step 5 A. Securely attach the press frame (17) to the pr.e.ss base (13) us;ng one 3" bolts (95), "~wo 1/2" washers C79), fo.u.r 3/8, washers (78), one nylock nu~s (B3). (Note: Make sure 3/8 bolts are facing down.) /2. x 3" bolt; (~,7), two 3/8 nylock nu~ 1,82), and two 9[...]

Step 6 A. SlTde two hinge tabs (73) onto the wolff sleeve (39) and securely attach press seat pl:ld (49) two 3/8 x 1" bolf;~ (97), and two 3/8" washers (78). (Note: The "hinge" part of the hinge should face upward.) ’B. Slide the right back pad angle (2) and left back pad angle (5) onto the wolff sleeve (39) attach the press b[...]

318 X LOV HEIGHT NUT HEIGHT NUT Step 7 A. Loosely attach the press arm odiu.sj (25) tp the rear up~!ght (21) using two 1" pillow block bearings (112), four 3/8 x 3-1/4: bolts ~9B), four 5/B washers ~TB~, and four 5/8" nylock nuts ~No~e: A~och pillow blocks ~112~ so the set screws ore on ~he inside, this w~ll ollow mote adjustment. B. Cent[...]

Step 8 A. Co 31/B X 3-1/4 ° ~ ,~~ (~1/2 X 3-114" Securely attach the re(=r leg base (10) and ihe leg curl handle (9) to the leg frame (14) using 1/2 x 3- " bolts (.B9), two 3/8 x 3-1/4". ,,bolts (98), four 1/2" washers (79), four " wash ers (7B), two 11//~" nylock nuts (82), and two 3/B nylock Securely attach the righ[...]

STEP 9-A STEP 9-B ~ STEP g A. Slide two hinge tabs; (73) onto the leg frame (14) and securely attach leg scat pad (4T) using 3/8 x I" bolls (97), and two 5/B" washers (TB). (Nole: The "hinge" part of the hinge tab should face downward.) B. Atiach $wo roller p.a, ds (19) to the leg frame (14) u(s;;~ one 16-3/~".roller pad sh[...]

STEP 11. A. Securely assemble two 3/8" spring pins (62) to the leg curl/extension (8) as shown. B. Apply eight 1-1/2 x 5/A-" glides (63) to the outside surfaces of each roller pad adiuster (34) shown, and insert roller pad adjusters (34) into the leg curl/extenslon (8). (Note: Tl~e, end will need to be temporarily removed.) " C. Secu[...]

I Step 12 A. Insert two plate bushings ~102~ |nto She °’ParaBody" side of each of sixty weight plates (677 as shown. B. Insert one guide rod (28~ through one weight stock cushion (109~ and into each of the large hales in the base C15), the leg welghf stock base ~IB~, and the press weight stack press (1~ as shown. C. Ccrefully slide twen~ we[...]

3Z8 x 3"(~ Step , 13 Slide pec guide roC[ support (43..~ onto the pec welght.stack guide rods and Ioosely,,att,,ch it bolts (95), four 5/8 washers (78), and two 3/8 nyiock to the boom using two nuts (83). (Note: This connection will be secured in a later step after the pulleys are assembled.) B. Slide press guide rod support (24) and leg guide[...]

CABLE GUIDE PEC DEC% CABLE STAMPED 65356 -77 51B" PART NUMBER PRESS STAMPED 66274- PART NUMBER AB CRUN% ¯ CABLE /--- STAMPED PART NUMBER ./6707B . ,, ~,/ --60 3/4"- STAMPED PART NUMBER 66276 " ’ // --~73 7/B’- STAMPED PART NUMBER 67047 -171"-- 17[...]

Pec Dec Cable Assembly Instructions Use this procedure to assemble the pec dec cables of the ParaBody 950ST Step C Step F & H Step G I 1318 x ~-3/4." 0 Step D __ E Step A. B. C, 1 In this order, route tthe threaded end of the let cable (107) through the top boom (20), the (15), and the large hole in the pec guTde rod support Screw the thre[...]

Step 2 of the pec dec cable (104) |o the slotted bushing on |h~ ri.ght p.ec A. Connect o.ne..end .... ~ ^~ the ~ec dec cable around the front upright {,31.~ anc~ 29. Route the o~l~er e.u .y, . .~% ..... ;o ~e slotted bush, ng on tne ,e’T P== ..... " WO 4--1/2" pulleys (110) to the center B. ~,~-~racket (36) using.~,~o ~/~ ~ ~ ~;;C "[...]

I I I I I I I / / / step A. Securely assemble ~!he threaded end of the ab crunch cable (105) approximately 3/4" into the end the pulley bracket (25) and tighten jam nut securely. B. Securely ass_e,,rnble ’the pec dec c.a.b,,le ~104) a.nd one 5-1/2 pu},ley (11) to the pulley bracket (25) one 3/e x z bolt (tOO), two 3/8 washe~ (78), and one 3/[...]

I I Step A. 4 Securely assemble the ball end of the ab .crunch cable (106).a,,nd one 3-1/2" pu. lley (’.111).t~,,,the front upright (51) using tw.o 3/6 x 2-3/4: bolts (gg), two 3/8’ flange spacers (74), washers (78), and two 3/8 nylock nuts (83). (Note: The ab crunch cable should be routed underneath the retaining bolt as shown.) the ab cr[...]

Press Station Cable Assembly Instructions Use this procedure to assemble the press station cable of the ParaBody 950!~T Step 1 A. Secure the ball end of the press cable .(105.) and two. ,3-1/2" pul!ey~. (111) to the. swive, I p, ulley, bracket (41) using two 3/8 x 2" bolts (,100), four 3/8" washers (78), and two 3/8" nylocK (Not[...]

Ao Secure the press cable (105) and two 3-1~/2" pulleys (111) ~o the pu!ley flats on the press base (13) and ~ ress weight slack base (1) using two 3//8 x 2" bolts (78), and two 3/8" nylock nuts (83). (Note: The cable should be routed underneath the shaft leg of the ’L’ bracket. Also the ’L’ brackets should be positioned s~ra[...]

STEP 1 A. 3/B X 2-3/4 ° Leg Station Cable Assembly Instructions Use this procedure to assemble the leg .station cable of the PARABOD¥ 950 S’T Route the "loop" end of the leg cable (lOB) into the rear sl,}t of the leg weight stack base (I"B) behind the welght stack, and out through the slot near the leg station. Securely attach [...]

STEP 2 A. Screw the threaded end of the leg cable 4108) approximately 3/4" into the end of the selector shaft (113) and tighten ]am nut securely as shown. B. If upon completion of assembly, the head plate 411.7) does not sit on fop of the first weight plate 467), push the head plate clown, insert the selector pin (72) and perform several repet[...]

B. Securely assemble the. = press station shroud (53) the press guide rod support (2,,4) and the press weight stack bose (1) using fhre=. = 3/8 x .1 .bla.ck button head cap screws (59) and one .3/8 X 1" bolt (~97). (,Note: The press shroud has ~he press exercise diagram.) 378 I]DLT Securely assemble th,s leg station shroud (52) to the leg guid[...]