Pelco C2423M manual

® SD5BCBW Series Spectra II™ Color/Black & White Dome Systems Operation and Programming Manual C2423M (5/00) P elco • 3500 P elco Wa y • Clovis , CA 93612-5699 USA • www .pelco .com In Nor th America and Canada: T el (800) 289-9100 • F AX (800) 289-9150 Inter national Customers: T el +1(559) 292-1981 • F AX +1(559) 348-1120[...]

CONTENTS Section Page IMPORT ANT SAFEGU ARDS AND WARNINGS ................................................................ 3 OPERA TION ...................................................................................................................... 4 POWER-UP DISPLA Y ...........................................................................[...]

IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and ser vicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designe[...]

OPERA TION POWER-UP DISPLA Y When the Spectra II™ dome is pow ered up, the selected protocol, re vision number , and other inf or mation is display ed on the monitor . For e xample, the screen might show the f ollo wing information: The information displa yed depends on the selected protocol (C, D , or P) and the menu selection f or power- PELCO [...]

OPERA TING NOTES P AN AND TIL T FUNCTIONS Controller T ype Pan Tilt Fixed speed Speed determined by controller Speed determined by controller Va r iable speed T urbo Mode Preset Mode 0.1 to 80 ° per second, depending on joystick position 150 ° per second 250 ° per second 0.1 to 40 ° per second, depending on joystick position 200 ° per second D[...]

NOTE: The dome cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern. PA TTERNS The Spectra II dome can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tilt or lens command. Presets, flip, and turbo are not allowed in[...]

AUXILIAR Y OUTPUTS An A UX 1 command from the controller will activate the rela y in the dome and operate the de vice that is connected to the relay . The relay will remain latched until a clear command is issued. An A UX 2 command from the controller will place a ground at the output of A UX 2 to operate the de vice that is connected to it. The ou[...]

PROGRAMMING Programming Guide - Spectra II Color/Black & White Gain/AGC Menu 1. Access main menu (preset 95). 2. Make main menu selections . Joystic k: Mov e up or down to position cursor or to toggle between selections. Iris Open: Enter Iris Close: Cancel PRESETS The follo wing presets are reserved for special functions . Preset Function 1 P a[...]

ACCESSING MAIN MENU (PRESET 95) NOTE: F or American Dynamics controllers with only 32 presets, set s witch SW1-7 on the dome drive in the ON position. When SW1-7 is ON, preset 99 becomes 32 98 becomes 31 97 becomes 30 96 becomes 29 95 becomes 28 93 becomes 26 92 becomes 25 91 becomes 24 90 becomes 23 89 becomes 22 88 becomes 21 If the limit stops a[...]

NOTE: Pattern length is set on the secondar y menu entitled Other . NOTE: To make the pattern r un to its end when an alarm activates it, mak e alar m dwell time longer than pattern length. Thus, if the alarm goes awa y before the end of the pattern, the pattern will continue until the dwell times out. ALARMS The Spectra II dome has se ven alarm in[...]

NOTE: The Spectra II Color/Black and White camera cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern. 6. P osition the cursor (>) beside the number of the alarm input for which you w ant to set the pattern. 7. Press the Iris Open button. The cursor mov es to the r ight, beside the words Full P at, Half P at 1, Half Pa[...]

AUTO FLIP Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Other Menu A uto flip On Proportional pan On Limit stops Off Park time minutes 0 Scan speed deg/s 25 Pattern length 1.5 min Exit There are two auto flip modes: On - Auto flip mode is enab led. Off - A uto flip mode is disa[...]

AUTO IRIS Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT A uto-Iris Menu A uto-iris mode A uto Auto-iris level 7 Exit Camera Menu Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC> <Auto-iris> <Next> Exit The following are the settings for auto iris: Mod[...]

AUTO IR LEVEL Main Menu Camera Menu Next Menu IR Filter Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Backlight comp O ff Zoom limit x72 Reset camer[...]

NOTE: If backlight compensation is ON and the IR cut filter switches OUT (black and white mode) in normal lighting condi- tions, adjust the A uto IR Level to a darker setting. Ref er to the Auto IR Le vel section. 4. Move the jo ystick up or down to position the cursor ne xt to either Aux 1 mode or A ux 2 mode. 5. Press the Ir is Open b utton. The [...]

GAIN/AGC Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Camera Menu Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC> <Auto-iris> <Next> Exit Gain/AGC Menu A GC mode Auto Gain 6 Exit Gain - The amount of amplification the camera places on its video info[...]

IR FIL TER MODE Main Menu Camera Menu Next Menu IR Filter Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Backlight comp Of f Zoom limit x72 Reset cam[...]

NOTE: Programming preset 90 (23) disables the manual limit stops until preset 91 (24) is set. NOTE: On power-up , the auto scan tilt angle will be whatever angle the camera was at when the right scan limit was set. TURNING LIMIT STOPS ON OR OFF To change the limit stop mode: 1. Prog ram preset 95 (28). The main menu appears. 2. P osition the cursor[...]

LINE SYNC PHASE - The cursor mov es to a numeric value. Move the jo ystick up or down to change the value . Press the Ir is Open b utton to select the choice. The value represents the phase angle in tenths of a degree between 0 degrees and 359 degrees. For example, 900 is 90 degrees, 1200 is 120 degrees, and 2400 is 240 degrees. Press the Iris Open[...]

POWER-UP MODE Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Po w er-Up Menu Pow er Up Default Exit This f eature lets the dome resume a desired condition following pow er-up. The menu includes the following choices. Default - On power-up, the dome goes through a configuration c[...]

3. Press the Iris Open button to enter the Other menu. 4. Position the cursor (>) beside Proportional Pan. 5. Press the Iris Open button. The cursor moves to the right, beside the word On or Off . 6. Mov e the joystic k up or down to toggle between On and Off . 7. SELECT - Press the Iris Open button on your keyboard to select your choice. CANCEL[...]

SCAN SPEED Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Other Menu A uto flip On Proportional pan On Limit stops Off Park time minutes 0 Scan speed deg/s 25 Pattern length 1.5 min Exit The scan speed is adjustable from 1-40 degrees per second. This occurs in three scan modes: [...]

SHUTTER SPEED Main Menu Camera Menu Next Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC> <Auto-iris> <Next> Exit Slow shutter mode Au to Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness&[...]

SLOW SHUTTER MODE Main Menu Camera Menu Next Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC> <Auto-iris> <Next> Exit Slow shutter mode Au to Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpn[...]

WHITE BALANCE Main Menu Camera Menu Next Menu White Balance Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Backlight comp Of f Zoom limit x72 Reset c[...]

ZONE BLANK Main Menu Alarms, Zone Blank Menu Zone Blank Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Alarm resume Off Alarm dwell sec 5 <Alarm priority> <Alarm pattern> <Zone blank> Exit Video Blank Zone 1Off 2Off 3Off 4Off 5Off 6Off 7Off 8Off Exit This f eature l[...]

MAINTENANCE DOME CLEANING Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch the surfaces of the dome. Exterior Surface - Clean the dome’ s e xter ior surf ace with a nonabrasive cleaning cloth and cleaning agent that is safe f or acrylic. Either liquid or spr ay cleaner/wax suitab le for fine furniture is [...]

Effectiv e Pixels NTSC: 768 (H) x 494 (V) P AL: 752 (H) x 582 (V) Horizontal Resolution: >470 TV lines Lens Minimum f-stop: F1.4 Focal Length: 4.1 mm to 73.8 mm optical Zoom Ratio: 18X optical zoom, 4X electronic zoom Digital Slow Shutter: Auto/manual speed selection Horizontal Angle of View: 48 ° (at 4.1 mm wide zoom), 2.7 ° (at 73.8 mm telep[...]