Philips 105S26 manual

Philips 105S Electronic User's Manual file:///C|/rita wu/gs3noVE/english/105S/Index.htm [11/3/2000 1:11:39 PM][...]

Safety and Troubleshooting Information Safety Precautions and Maintenance • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or me[...]

About This Electronic User's Manual About This Guide • Other Documents You May Need • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips 105S Color Monitor. It describes the monitor's features, setup, operation and all other information, which is the same exact inform[...]

Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: This icon indicates important information and tips that help you make better use of your computer system. CAUTION: This icon[...]

Product Information Product Features • Technical Specifications • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Product Features 105S20 15-inch (14.0" VIS) color monitor with excellent front of screen performance for use with MACs and PCs ● Autoscan covers horizontal frequencies up to 63 kHz offer[...]

Technical Specifications* CRT • Size and deflection 15 inch / 36 cm ; 90° deflection angle • Dot pitch / Grille pitch 0.28 mm • Horizontal pitch 0.24 mm • Tube type Shadow mask, flat square, high contrast, anti-glare, anti-static, anti reflection, light transmission 57% • Phosphor P22 • Recommended display area 10.6" x 7.95" [...]

If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. And if an input from a keyboard, mouse or other input device is detected, the monitor will automatically "wake up". The following table shows the power consumption and signaling[...]

The 15-pin D-sub connector (male) of the signal cable (IBM systems): Pin No. Assignment Pin No. Assignment 1 Red video input 9 No pin 2 Green video input 10 Logic ground 3 Blue video input 11 Identical output - connected to pin 10 4 Identical output - connected to pin 10 12 Serial data line (SDA) 5 Ground 13 H. Sync / H+V 6 Red video ground 14 V. S[...]

Installing your Monitor Front View • Rear View • 6G3B11 Multimedia Base (option) • PCUH411 USB Hub (option) Front View Power button switches your monitor on. OK button which when pressed will take you to the OSD controls Contrast hotkey. When the UP arrow is pressed, the adjustment controls for the CONTRAST will show up. UP and DOWN buttons a[...]

Brightness hotkey. When both the LEFT and RIGHT arrows are pressed at the same time, then the adjustment controls for BRIGHTNESS will show up. LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. RETURN TO TOP OF THE PAGE Rear View Installing your Monitor file:///C|/rita wu/gs3noVE/english/105S/i[...]

1. Power in - attach power cable here. 2. Video In - this is a cable which is already attached to your monitor. Connect the other end of the cable to your PC. RETURN TO TOP OF THE PAGE Installing your Monitor file:///C|/rita wu/gs3noVE/english/105S/install/install.htm (3 of 3) [11/3/2000 1:13:08 PM][...]

On-Screen Display Description of the On-Screen Display • The OSD Tree • The OSD Controls Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips monitors which allows an end-user to adjust screen performance of monitors directly though an on-screen instruction window. The user interface provides user[...]

RETURN TO TOP OF THE PAGE The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments. On-Screen Display file:///C|/rita wu/gs3noVE/english/105S/osd/osddesc.htm (2 of 4) [11/3/2000 1:13:10 PM][...]

On-Screen Display file:///C|/rita wu/gs3noVE/english/105S/osd/osddesc.htm (3 of 4) [11/3/2000 1:13:10 PM][...]

RETURN TO TOP OF THE PAGE On-Screen Display file:///C|/rita wu/gs3noVE/english/105S/osd/osddesc.htm (4 of 4) [11/3/2000 1:13:10 PM][...]

Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO READ THE WARRANTY COVERED: WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: C[...]

Glossary A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A Autoscan A microprocessor-based feature of Philips Brilliance monitors is able to detect automatically horizontal and vertical frequencies of input signals with those of the installed video card. An autoscan monitor can thus operate with a wide range of video cards. MultiSync, a registe[...]

C CE Mark CE mark is displayed on products per EMC and LV ( low Voltage Device ) directives in compliance with European Community safety, EMI and EMS requirements and is compulsory on products for sale in the European Community. Color temperature A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of [...]

Points where convergence error is specified . Convergence-error correction A method of correcting for convergence error to insure that all three beams land simultaneously in the same triad. This is usually accomplished by means of special convergence-error correction coils in the deflection yoke. CRT Cathode-ray tube - the general term for all tube[...]

DDC is a communication channel for displays and computers. The DDC feature allows the monitor controller to be automatically configured to make optimal use of the display without manual user interaction. DDC is implemented as part of the new Plug & Play approach introduced into the PC market to increase user friendliness. The three levels devel[...]

Dot rate Frequency in MHz of the dot clock. It is a measure of the speed with which data is transferred between the video card and subsequent processing circuitry. Also known as video dot rate. RETURN TO TOP OF THE PAGE E Electromagnetic radiation standards International standards set to limit electromagnetic emissions from monitors. There are curr[...]

In 1991, the Swedish Tjänstemannens Central Organization (TCO, Swedish confederation of Professional Employees ) set a standard even more severe than MPR-II, especially for alternating electric fields (AEF). The TCO standard is more severe since not only are the permitted field levels reduced compared with MPR-II, but the measuring distance is als[...]

Also called line frequency and expressed in kHz, it is the number of video lines written on the screen every second (from left to right). The higher the horizontal scanning frequency, the better the resolution (i.e., the higher the resolution and/or the higher the refresh rate). RETURN TO TOP OF THE PAGE I INF File INF file (Information File) Infor[...]

L Linearity The degree to measure the actual location of a pixel on the screen corresponds with its intended location. ( see figure ) Line frequency See Horizontal scanning frequency. Low-emission monitor A monitor that complies with international standards on radiation. See Electromagnetic radiation standards. Low-frequency electric and magnetic f[...]

M Moiré effect A fringe pattern arising from the interference between two superimposed line patterns. In a monitor it comes from the interference between the shadow mask pattern and the video information (video moiré), and between the shadow mask pattern and the horizontal line pattern (scan moiré). It shows itself as wavy patterns on the screen[...]

screen area, resulting in an image that is smaller (and less legible) than it needs to be. RETURN TO TOP OF THE PAGE P Parallelogram Distortion See Geometric distortion. Phosphor Generic name for the class of substances that exhibit luminescence. To produce a picture on screen, phosphors are deposited on the inner surface of the picture-tube screen[...]

R Raster The area on screen that electron beam can reach. Refresh rate See Vertical scanning frequency. Resolution The number of pixels that can be displayed on the screen. The resolution is specified as the number of pixels in a line multiplied by the number of horizontal lines. See also video graphic adapter. Rotation function The feature that al[...]

Anti-Static coatings Due to bombardment by beam electrons, monitor screens become electrically charged when in use. Electrically charged screens surfaces can attract dust particles. An Anti-Static coating is a conductive coating deposited on the screen (or on a glass panel immediately in front of the screen) that conducts away the charge and preven[...]

The ARAS coating reflects only about 0.5% of the incident light. AGRAS (Anti-Glare anti-Reflection Anti-Static) coating . A combined anti-reflection, anti-glare, anti-static coating. Self-test function A monitor equipped with hardware or software to automatically detect cable connection status. Shape Deviation of a reproduced picture from its inten[...]

SOG (Synchronization On Green) A properly functioning color monitor requires five kinds of signals: horizontal sync pulse, vertical sync pulse, red color signal, green color signal and blue color signal. Signals from a PC are transmitted to a monitor using one of three methods: 1. Separate sync: Horizontal and Vertical sync signals transmitted sepa[...]

See rotation function. Trapezoid distortion See Geometrical distortion. TTL signal A TTL (Transistor-transistor-logic) signal is a digital signal level for controlling the screen colors. With TTL driving, the red, green and blue signals can only be switched on or off or provided with an intensity signal. A TTL-driven monitor can thus display a maxi[...]

signaling. A hub consists of two portions: the Hub Controller and Hub Repeater. The repeater is a protocol-controlled switch between the upstream port and downstream ports. It also has hardware support for reset and suspend/resume signaling. The controller provides the interface registers to allow communication to/from the host. Hub specific status[...]

V Vertical dot pitch See Dot pitch. Vertical scanning frequency Expressed in Hz, this is the number of fields written to the screen every second in interlaced mode. In non-interlaced mode vertical scanning frequency is the number of frames (complete pictures) written to the screen every second (also known as refresh rate). Vertical sync pulses A tr[...]

resolutions from 1280 x 1024 to 1600 x 1280, horizontal line frequencies up to 90 kHz and bandwidths up to 200 MHz. VIS (Viewable Image Size) The real screen dimensions that users can see measured diagonally. The VIS of a monitor is always less than the so called screen size of a monitor. For example, the VIS of a 17-inch monitor is only about 16 i[...]

Download and Print This page provides an option to read the manual in .pdf format. PDF files can be downloaded into your hard disk, then viewed and printed with Acrobat Reader or through your browser. If you do not have Adobe¨ Acrobat Reader installed, click on the link to install the application. Adobe® Acrobat Reader for PC / Adobe® Acrobat Re[...]

Troubleshooting Safety Precautions and Maintenance • Troubleshooting • Regulatory Information • Other Related Information Common Problems Having trouble? Something not working? Before calling for help, try these suggestions. Having this problem? Check these items No Picture (Power LED not lit) Make sure the Power cable is plugged into the pow[...]

Dim Picture Adjust the Brightness and Contrast controls. ● Check your video card and it's owner's manual instructions for it may be a non-VESA-DDC Standard card. ● Picture is too large or too small. Adjust the Horizontal and/or Vertical Size. ● Adjust the Zoom. ● Edges of the picture are not square. Adjust the geometry. ● Pictur[...]

Regulatory Information TCO'92 and TCO '99 Information • TCO Environmental Requirements • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S. Only) • Commission Federale de la Communication (FCC Declaration) • EN 55022 Compliance (Czech Republic Only) • VCCI Class 2 Notice (Japan Only) • MIC Notice [...]

This product meets the requirements for the TCO'99 scheme which provides for international and environmental labeling of personal computers. The labeling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Staten[...]

Cadmium** Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries, the color-generating layers of display screens and the electrical or electronics components must not contai[...]

Normal operation ON Green < 75 W Power Saving Position A1 Suspend Yellow < 15 W Power Saving Position A2 OFF Amber < 8 W A s an E NERGY S TAR ® P artner, PHILIPS has determined that this product meets the E NERGY S TAR ® guidelines for energy efficiency. We recommend you switch off the monitor when it is not in use for quite a long time.[...]

RETURN TO TOP OF THE PAGE Commission Federale de la Communication (FCC Declaration) Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon à fourir une protection raisonnable contre les interférences nuisibles d[...]

RETURN TO TOP OF THE PAGE VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment acco[...]

RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room's electrical[...]

Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELP[...]

Ergonomie Hinweis (nur Deutschland) Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen" festgelegten Vorschriften. Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme hinweist, da die Vorschriften über die Bauart[...]

moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place. If the mai[...]

that the cord grip is clamped over the sheath of the lead - not simply over the three wires. RETURN TO TOP OF THE PAGE Regulatory Information file:///C|/rita wu/gs3noVE/english/105S/safety/regs/regulat.htm (11 of 11) [11/3/2000 1:13:39 PM][...]

Other Related Information Safety Precautions and Maintenance • Troubleshooting • Regulatory Information • Information for Users in the U. S . • Information for Users Outside the U.S Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maxi[...]

6G3B11 Multimedia Base (option) Front View • Rear View • Technical Specifications • Description of the Controls • Installing your Multimedia Base Technical Specifications* • Output power 2 x 1.5W RMS / 36W PMPO • Bass Boost • Headphone connection 3.5 mm jack • Microphone in/out 3.5 mm jack • Includes Audio cable and AC adapter •[...]

D. Microphone jack Attach your microphone here. E. Audio In Connect this to the audio output of your PC. F. MIC Out Connect this to the microphone output of your PC. G. DC Input Connect power input here. RETURN TO TOP OF THE PAGE Installing your Multimedia Pedestal 1. To INSTALL Slide the pedestal, aligning with the holes on the side. ● Then clic[...]

2. To UN-INSTALL Lift the back hook from the hole on the bottom plate of your monitor. ● Slide out the pedestal the opposite direction (from when you installed it). ● RETURN TO TOP OF THE PAGE 6B3G11 Multimedia Base (option) file:///C|/rita wu/gs3noVE/english/105S/install/mm_pede/mm_inst.htm (3 of 3) [11/3/2000 1:14:33 PM][...]

PCUH411 USB H ub (Option) Front View • Rear View • Installing your USB Hub Installing your USB Hub Installing on a conventional base. 1. Take out the USB hub from the box. 2. Take off the USB hub cover. 3. Slightly tilt and lift the base of your monitor. 4. Attach the USB hub by clipping into the base. 5. You can reposition the USB hub along th[...]

6. Position the USB hub to the back of the Multimedia Pedestal. 7. Attach the USB hub by sliding-in to the Multimedia base. RETURN TO TOP OF THE PAGE USB Hub (Optional Feature) file:///C|/rita wu/gs3noVE/english/105S/install/usbhub/usb_inst.htm (2 of 2) [11/3/2000 1:14:34 PM][...]

The OSD Controls Description of the On-Screen Display • The OSD Tree The OSD Controls : Brightness (HotKey) • Contrast (HotKey) • Language • Input Signal Selection • Zoom • Adjust Horizontal • Adjust Vertical • Adjust Shape • Adjust Color • Reset to Factory Settings • Extra Controls • Close Main Controls BRIGHTNESS To adjust[...]

1) Press the or button on the monitor. The CONTRAST window appears. 2) Press the or button to adjust the contrast. 3) When the contrast is adjusted to the level desired, stop pressing the or button and after three seconds the CONTRAST window will disappear with the new adjustment saved. Smart Help After the CONTRAST window has disappeared, to conti[...]

3) Press the or button until the desired language is highlighted. 4) Press the button to confirm your selection and return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted... Smart Help After returning to MAIN CONTROLS . . . . . . to continue to INPUT SIGNAL SELECTION, press the button until INPUT SIGNAL SELECTION is highlighted. Ne[...]

RETURN TO TOP OF THE PAGE INPUT SIGNAL SELECTION (Not available in all models) INPUT SIGNAL SELECTION determines what you see on the screen. The default setting is INPUT A, but if the video input signal is different that the output signal, you may want to change it to INPUT B.? 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2[...]

MAIN CONTROLS will be highlighted. Smart Help After returning to MAIN CONTROLS . . . . . . to continue to ZOOM, press the button until ZOOM is highlighted. Next, follow steps 3 - 5 under ZOOM. . . . to exit completely, press the button RETURN TO TOP OF THE PAGE ZOOM ZOOM increases or decreases the size of the images on your screen. To adjust the ZO[...]

4) Press the or button to adjust ZOOM. 5) Press the button to confirm your selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. Smart Help After returning to MAIN CONTROLS . . . . . . to continue to ADJUST HORIZONTAL, press the button until ADJUST HORIZONTAL is highlighted. Next, follow steps 3 - 7 under ADJUST[...]

3) Press the button. The ADJUST HORIZONTAL window appears. ADJUST POSITION should be highlighted. 4) Press the or button to move the image to the left or right. 5) When the position is adjusted, press the button to return to MAIN CONTROLS window, or press the to highlight ADJUST SIZE. 105S The OSD Controls file:///C|/rita wu/gs3noVE/english/105S/os[...]

6) To adjust the horizontal size, press the or button. 7) When the size is adjusted, press the button to return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. Smart Help After returning to MAIN CONTROLS . . . . . . to continue to ADJUST VERTICAL, press the button until ADJUST VERTICAL is highlighted. Next, start with step 3 under[...]

3) Press the button. The ADJUST VERTICAL window appears. ADJUST POSITION should be highlighted. 4) Press the or button to move the image up or down. 5) When the position is adjusted, press the button to return to MAIN CONTROLS window, or press the to highlight ADJUST SIZE. 105S The OSD Controls file:///C|/rita wu/gs3noVE/english/105S/osd/osd_cont.h[...]

6) To adjust the vertical size, press the or button. 7) When the size is adjusted, press the button to return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. Smart Help After returning to MAIN CONTROLS . . . . . . to continue to ADJUST SHAPE, press the button until ADJUST SHAPE is highlighted. Next, start with step 3 under ADJUST [...]

3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the button. The SIDE CURVE window appears. PINCUSHION should be highlighted. 105S The OSD Controls file:///C|/rita wu/gs3noVE/english/105S/osd/osd_cont.htm (11 of 25) [11/3/2000 1:15:13 PM][...]

5) To adjust the pincushion, press the or button. 6) When the pincushion is adjusted, press the button to highlight BALANCED or press the button to return to the ADJUST SHAPE window. 7) To adjust the balanced pincushion, press the or button. 8) When the balanced pincushion is adjusted, press the button to return to the ADJUST SHAPE window. BACK TO [...]

Smart Help After returning to MAIN CONTROLS . . . ...to continue to ADJUST SIDE ANGLES, start with step 5 under ADJUST SIDE ANGLES and follow the directions. ...to exit completely, press the button twice. ...to adjust only the BALANCED pincushion, follow steps 1 - 4 above, then press the button, and follow steps 7 - 9. ADJUST SIDE ANGLES ADJUST SID[...]

4) Press the button to highlight ADJUST SIDE ANGLES. 5) Press the button. The SIDE ANGLES window appears. TRAPEZOID should be highlighted. 6) To adjust the trapezoid, press the or button. 7) When the trapezoid is adjusted, press the button to highlight PARALLELOGRAM or press the button to return to the ADJUST SHAPE window. 105S The OSD Controls fil[...]

8) To adjust the parallelogram, press the or button. 9) When the parallelogram is adjusted, press the button to return to the ADJUST SHAPE window. BACK TO MAIN WINDOWS will be highlighted. 10) Press the button to return to the MAIN CONTROLS window, or press the button until ROTATE IMAGE is highlighted. Smart Help After returning to MAIN CONTROLS . [...]

3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the arrow until ROTATE IMAGE is highlighted. 5) Press the button. The ROTATE IMAGE window appears. ROTATE should be highlighted. 105S The OSD Controls file:///C|/rita wu/gs3noVE/english/105S/osd/osd_cont.htm (16 of 25) [11/3/2000 1:15:13 PM][...]

6) To adjust the rotation, press the or button. 7) When the rotation is adjusted, press the button to return to the ADJUST SHAPE window. BACK TO MAIN CONTROLS should be highlighted. 8) Press the button to return to MAIN CONTROLS. Smart Help After returning to MAIN CONTROLS . . . . . . to continue to ADJUST COLOR, press the button until ADJUST COLOR[...]

3) Press the button. The ADJUST COLOR window appears. 4) Press the or button to highlight 9300K for GENERAL USE, 6500K for GAMES, or USER PRESET. 5) Once you have highlighted GENERAL USE or GAMES, press the button to confirm you selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. 105S The OSD Controls file:///[...]

6a) ?If USER PRESET is highlighted, press the button to highlight RED. Next, press the LEFT CURSOR or RIGHT CURSOR button to adjust the color red. 6b) ?When finished with RED, press the button to highlight GREEN. Next, press the or button to adjust the color green. 6c) ?When finished GREEN, press the button to highlight BLUE. Next, press the or but[...]

RESET TO FACTORY SETTINGS returns everything in all the windows to factory presets. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until RESET TO FACTORY SETTINGS is highlighted. 3) Press the button. The RESET TO FACTORY SETTINGS window appears. 4) Press the or button to select YES or NO. NO is the default[...]

Smart Help After returning to MAIN CONTROLS . . . . . . to continue to EXTRA CONTROLS, press the button until EXTRA CONTROLS is highlighted. Next, start with step 3 under EXTRA CONTROLS. . . . to exit completely, press the button. RETURN TO TOP OF THE PAGE EXTRA CONTROLS DEGAUSS EXTRA CONTROLS is a set of three features, including DEGAUSS. Degaussi[...]

4) To degauss your screen, press the button. Your screen will be degaussed, then the MAIN CONTROLS window will reappear. CLOSE MAIN CONTROLS will be highlighted. Smart Help After returning to MAIN CONTROLS . . . . . . to continue to ADJUST MOIRE, press the button until EXTRA CONTROLS is highlighted. Next, start with step 3 under EXTRA CONTROLS, ADJ[...]

3) Press the button. The EXTRA CONTROLS window appears. DEGAUSS will be highlighted. 4) Press the button until ADJUST MOIRE is highlighted. 5) Press the button. The ADJUST MOIRE window appears. HORIZONTAL will be highlighted. 105S The OSD Controls file:///C|/rita wu/gs3noVE/english/105S/osd/osd_cont.htm (23 of 25) [11/3/2000 1:15:13 PM][...]

6) To adjust the horizontal moire, press the or button. 7) When the horizontal moire is adjusted, press the button to highlight VERTICAL. 8) To adjust the vertical moire, press the or button. 9) When the vertical moire is adjusted, press the button to return to the EXTRA CONTROLS window. BACK TO MAIN CONTROLS will be highlighted. Smart Help After r[...]

CLOSE MAIN CONTROLS RETURN TO TOP OF THE PAGE 105S The OSD Controls file:///C|/rita wu/gs3noVE/english/105S/osd/osd_cont.htm (25 of 25) [11/3/2000 1:15:13 PM][...]

Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly[...]

Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a pe[...]

LIMITED WARRANTY (Computer Monitor) Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange* *Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year. This product must be shipped in at your expense for service during years two and three. WHO IS COVERED? You [...]

Where IS SERVICE AVAILABLE? Warranty service is available in all countries where the product is officially distributed by Philips Consumer Electronics. In countries where Philips Consumer Electronics does not distribute the product, the local Philips service organization will attempt to provide service (although there may be a delay if the appropri[...]

This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province. Philips Customer Care Center, P. O. Box 2976, Longview, TX 75601 Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standar[...]