Philips 150T4 manual

Manual file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/MANUAL.HTM [3/2/2004 3:43:45 PM][...]

Safety and Troubleshooting Safety and Troubleshooting Information Safety Precautions and Maintenance • Installation Locations • FAQs • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation [...]

Safety and Troubleshooting RETURN TO TOP OF THE PAGE Installation Locations ● Avoid exposure to heat and extreme cold ● Do not store or use the product in locations exposed to heat, direct sunlight or extreme cold. ● Avoid moving the product between locations with large temperature differences. Choose a site that falls within the following te[...]

About This Manual About This Manual About This Guide • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips LCD Monitor TV. It describes the features, setup, operation and other important information. It includes the following sections: ● Safety and Troubleshooting Information pr[...]

About This Manual Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks contain notes, cautions or warnings. They are used as follows: NOTE: This icon indicates important information and tips that help you make better use of your computer system. CAUTION: This icon indicates information[...]

Product Information Product Information Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views • Physical Function Product Features 150T4 ● 15-inch XGA LCD all-in-one Monitor TV with excellent displ[...]

Product Information PC SCANNING • Vertical refresh rate 56Hz-76Hz • Horizontal frequency 30kHz-63kHz PC VIDEO • Video dot rate 80 MHz • Input impedance - Video 75 ohm - Sync 2K ohm • Input signal levels 0.7 Vpp • Sync input signal Separate sync • Sync polarities Positive and negative • Input Frequency XGA Hsync 48- 63 kHz, Vsync 60 [...]

Product Information • Peak contrast angle 6 o'clock • White Chromaticity x: 0.283 y: 0.297 (at 9300° K) x: 0.313 y: 0.329 (at 6500° K) x: 0.313 y: 0.329 (sRGB) • Viewing Angle (C/R >5) Upper >50° (typ.) Lower >60° (typ.) Left >75° (typ.) Right >75° (typ.) • Response time <=25ms (typ.) * This data is subject to c[...]

Product Information Resolution Mode H. freq (kHz) V. freq (Hz) PC 640*350 VGA-1 31.469 70.086 640*480 VGA VESA 60 31.469 59.940 640*480 Mac 13 35.000 66.667 640*480 VGA VESA 75 37.500 75.000 720*400 IBM VGA 3H 31.468 70.087 800*600 SVGA VESA 56 35.156 56.250 800*600 SVGA VESA 60 37.879 60.317 800*600 SVGA VESA 75 46.875 75.000 832*624 Mac 16 49.724[...]

Product Information Automatic Power Saving If you have VESA DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will then 'wake up' automatically. The following table show[...]

Product Information • System MTBF 50K hrs (excluding CCFL 40Khrs) * This data is subject to change without notice. RETURN TO TOP OF THE PAGE Pin Assignment The 15-pin D-sub connector (male) of the signal cable: Pin No. Assignment Pin No. Assignment 1 Red video input 9 DDC +5V 2 Green video input 10 Logic ground 3 Blue video input 11 Ground 4 Grou[...]

Product Information RETURN TO TOP OF THE PAGE Product Views Follow the links to see various views of the monitor and its components. Front View Product Description RETURN TO TOP OF THE PAGE Physical Function Tilt file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/product/product.htm (7 of 8) [3/2/2004 3:43:52 PM][...]

Product Information RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/product/product.htm (8 of 8) [3/2/2004 3:43:52 PM][...]

Installing your LCD Monitor/TV Installing your LCD Monitor/TV Front View Product Description • Connecting to Your PC, TV antenna, DVD/VCR etc. • VESA Mounting and Easy Wall Mounting • Installing the Optional TV/AV Module • Getting Started • Optimising Performance Front View Product Description 1 SOURCE TV/Video source selection file:///D|[...]

Installing your LCD Monitor/TV 2 Increase or decrease the channel number or up or down the highlighted function in OSD 3 MENU Open the OSD and select the highlighted function 4 VOL Increase or decrease the level of audio volume or move up or down the highlighted function in OSD 5 Power indicator 6 Power switch On/Off 7 Receiver for 'remote con[...]

Installing your LCD Monitor/TV 1 DC 12V out For connect to "Audio Chin" only 2 AC in AC power in 3 VGA D-Sub input 4 PC - Audio in For connect to PC Audio output 5 Audio out For connect to Audio out RETURN TO TOP OF THE PAGE Optimizing Performance ● For best performance, ensure that your display settings are set at 1024x768@60Hz (for 15[...]

On-Screen Display On-Screen Display Description of the On-Screen Display • The OSD Guide Description of the On Screen Display What is the On-Screen Display? This is a feature offered by all Philips LCD monitors/TVs. It allows an end user to adjust screen performance of monitors directly through an on-screen instruction window. The user interface [...]

On-Screen Display Europe OSD Guide PC Mode INPUT SELECT Select video source for main display: PC ● PC VGA input TV ● Antenna or cable TV input AV ● CVBS Composite Video input S-VIDEO ● S-video input HD-YPbPr ● Progressive video input & YPbPr component video input LANGUAGE Set language for OSD ENGLISH DEUTSCH ITALIANO ADJUST POSITION A[...]

On-Screen Display VIDEO NOISE Adjust phase and clock to obtain stable and clear display PHASE CLOCK ADJUST COLOR Set color temperature to suit personal preference ORIGINAL PANEL COLOR 9300K FOR CAD/CAM 6500K FOR IMAGE MANAGEMENT SRGB USER PRESET RED GREEN BLUE RESET TO FACTORY SETTINGS Reset the setting to default values NO YES AUTO Automatic adjus[...]

On-Screen Display TV ● Antenna or cable TV input AV ● CVBS Composite Video input S-VIDEO ● S-video input HD-YPbPr ● Progressive video input & YPbPr component video input PICTURE Adjust picture characteristics to suit personal preference BRIGHTNESS CONTRAST COLOR SHARPNESS COLOR TEMP ● Normal ● Cool ● Warm EXIT SOUND Adjust audio c[...]

On-Screen Display ITALIANO INSTALL Install a TV program list SYSTEM Specify the TV system at the user location: ● WEST EUR ● FRANCE AUTO STORE Scan and store the TV programs at the user location automatically MANUAL STORE ● Search ● Prog. No ● Fine tune ● Store ● Exit Fine tune and store the TV programmes at the user location manually[...]

On-Screen Display Asia Pacific and China OSD Guide (excluding Korean, Taiwan and Philippines) PC Mode INPUT SELECT Select video source for main display: PC ● PC VGA input TV ● Antenna or cable TV input AV ● CVBS Composite Video input S-VIDEO ● S-video input HD-YPbPr ● Progressive video input & YPbPr component video input LANGUAGE Set [...]

On-Screen Display ADJUST COLOR Set color temperature to suit personal preference ORIGINAL PANEL COLOR 9300K FOR CAD/CAM 6500K FOR IMAGE MANAGEMENT sRGB USER PRESET RED GREEN BLUE RESET TO FACTORY SETTINGS Reset the setting to default values NO YES AUTO Automatic adjustment of the display parameters to give optimum display EXIT Exit from this menu R[...]

On-Screen Display S-VIDEO ● S-video input HD-YPbPr ● Progressive video input & YPbPr component video input PICTURE Adjust picture characteristics to suit personal preference BRIGHTNESS CONTRAST COLOR SHARPNESS TINT COLOR TEMP ● Normal ● Cool ● Warm EXIT SOUND Adjust audio characteristics to suit personal preference TREBLE BASS BALANCE[...]

On-Screen Display MANUAL STORE Fine tune and store the TV programs at the user location manually CHANNEL SKIP Set the skipped programme when accessing programmes using the keys CHANNEL SWAP EXIT VIDEO MODE REGULAR When viewing regular 4:3 format video signal WIDE When viewing wide (16:9) format video signal, e.g. HD EXIT Exit from this menu RETURN [...]

On-Screen Display HD-YPbPr ● Progressive video input & YPbPr component video input LANGUAGE Set language for OSD ENGLISH ADJUST POSITION Adjust positions to obtain optimum display location on the screen HORIZONTAL VERTICAL BRIGHTNESS & CONTRAST Adjust brightness and contrast to obtain optimum display BRIGHTNESS CONTRAST VIDEO NOISE Adjust[...]

On-Screen Display NO YES AUTO Automatic adjustment of the display parameters to give optimum display EXIT Exit from this menu RETURN TO TOP OF THE PAGE TV/Video/HD Mode INPUT SELECT Select video source for main display: PC ● PC VGA input TV ● Antenna or cable TV input AV ● CVBS composite video input S-VIDEO ● S-video input HD-YPbPr ● Prog[...]

On-Screen Display COLOR TEMP ● Normal ● Cool ● Warm EXIT SOUND Adjust audio characteristics to suit personal preference TREBLE BASS BALANCE SURROUND (ON/OFF) EXIT LANGUAGE Set language for OSD ENGLISH INSTALL Install a TV program list TUNER MODE Set the tuner mode: ● auto ● antenna ● cable AUTO STORE Scan and store the TV programs at th[...]

On-Screen Display VIDEO MODE REGULAR When viewing regular 4:3 format video signal WIDE When viewing wide (16:9) format video signal, e.g. HD EXIT Exit from this menu RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/osd/osddesc.htm (13 of 13) [3/2/2004 3:43:57 PM][...]

TV Control TV Control Using Your Remote Control Using Other Menu: ● Europe area ● Asia Pacific area and China excluding Korea, Taiwan and Philippines ● Americas, Korea, Taiwan and Philippines Using Your Remote Control For European countries For countries outside Europe For European countries Remote Control Diagram file:///D|/My%20documents/df[...]

TV Control 1 Standby To set the TV temporarily to standby mode. To switch on the TV set, press Programme button (CH -, +), any digit between 0 and 9 or AV source button (The amber light indicates when set is in standby mode) 2 Numerical keys ● For direct access to programmes For a 2-digit programme number, the 2nd digit must be entered before the[...]

TV Control 3 Menu ● To turn on or off the OSD (On-Screen Display) ● To return to last item in OSD & clear menu from screen 4 Volume ● To adjust the sound level. ● To access the sub-menus and adjust the settings. 5 Previous programme To access the last programme viewed. 6 SOURCE ● To select PC, TV, AV, S-Video and HD mode. ● In PC &a[...]

TV Control 12 Screen mode To switch between 4:3 and 16:9 video format for optimum viewing ratio. RETURN TO TOP OF THE PAGE For countries outside Europe Remote Control Diagram file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/osd/tv_control.htm (4 of 6) [3/2/2004 3:44:00 PM][...]

TV Control 1 Standby To set the TV temporarily to standby mode. To switch on the TV set, press Standby button, Programme button (CH -, +), any digit between 0 and 9 or AV source button. (The amber light indicates when set is in standby mode) 2 Numerical keys ● For direct access to programmes For a 2-digit programme number, the 2nd digit must be e[...]

TV Control 9 Selecting TV programmes ● To move up or down a programme. ● To move the cursor up/down to scroll through a list of options. ● In PC/Video 'Standby' mode, press CH+/- to return to 'on' in TV mode. 10 OSD To show OSD status. 11 Sleep timer To select the period of time after which the set will switch automaticall[...]

Customer Care and Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • S[...]

Download and Print Download and Print Installing your LCD monitor driver • Download and Printing Instructions • Installing FPadjust Program Installing Your LCD monitor driver System requirements: ● PC running Windows® 95, Windows® 98, Windows® 2000 , Windows® Me, Windows® XP or later ● Find your driver ".inf/.icm/.cat" at : /[...]

Download and Print 2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to Disk'. 3. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or 'source', choose 'source'). Printing instructions: To[...]

Download and Print 'source', choose 'source'). ● Exit your browser and install the FPadjust Program. Read the "FP_Readme03.txt" file before installing. RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/download/download.htm (3 of 3) [3/2/2004 3:44:03 PM][...]

FAQs (Frequently Asked Questions) FAQs (Frequently Asked Questions) Safety and Troubleshooting • General FAQs • Screen Adjustments • Compatibility with Other Peripherals • LCD Panel Technology • Ergonomics, Ecology and Safety Standards • Troubleshooting • Regulatory Information • Other Related Information General FAQs Q: When I inst[...]

FAQs (Frequently Asked Questions) ROM) included in this package. Monitor drivers (.inf and .icm files) will be installed automatically. Q: How do I adjust the resolution? A: Your video card/graphic driver and monitor together determine the available resolutions. You can select the desired resolution under Windows® 95/98 Me & 2000/XP with the &[...]

FAQs (Frequently Asked Questions) A: A protective coating is applied to the surface of the LCD, which is durable to a certain extent (approximately up to the hardness of a 2H pencil). In general, it is recommended that the panel surface is not subject to any excessive shocks or scratches. An optional protective cover with greater scratch resistance[...]

FAQs (Frequently Asked Questions) 1. For best performance, make sure your display settings are set at 1024x768@60Hz for 15". Note: You can check the current display settings by pressing the OSD OK button once. The current display mode is shown in the product information in the OSD main controls. 2. To install the Flat Panel Adjust (FPadjust) p[...]

FAQs (Frequently Asked Questions) luminance signals Y (black and white) and chrominance signals C (colour) are recorded separately on the tape. This provides a better picture quality than is achieved with standard video (VHS and 8 mm) where the Y/C signals are combined to provide only one video signal. RETURN TO TOP OF THE PAGE LCD Panel Technology[...]

FAQs (Frequently Asked Questions) Q: What differentiates passive matrix LCDs from active matrix LCDs? A: An LCD is made with either a passive matrix or an active matrix display grid. An active matrix has a transistor located at each pixel intersection, requiring less current to control the luminance of a pixel. For this reason, the current in an ac[...]

FAQs (Frequently Asked Questions) has 1024x3 (R, G, B) x 768 pixels and a higher resolution may not be available without additional software processing. The panel is designed to optimise the display for a 65MHz dot clock, one of the standards for XGA displays. Since the vertical/horizontal frequency for this dot clock is 60Hz/48kHz, the optimum fre[...]

FAQs (Frequently Asked Questions) Ergonomics, Ecology and Safety Standards Q: What is the CE mark? A: The CE (Conformité Européenne) mark is required to be displayed on all regulated products offered for sale on the European market. This 'CE' mark means that a product complies with the relevant European Directive. A European Directive i[...]

Troubleshooting Troubleshooting Safety and Troubleshooting • FAQs • Common Problems • Imaging Problems • TV and Audio Problems • Regulatory Information • Other Related Information This page deals with problems that can be corrected by the user. If the problem still persists after you have tried these solutions, contact your nearest Phil[...]

Troubleshooting Image vibrates on the screen ● Check that the signal cable is properly connected to the graphics board or PC. Vertical flicker appears ● Press "MENU" and "DOWN" hot keys at front control together to automatically adjust at PC mode. ● Press "MENU" key to select "AUTO". Horizontal flicker [...]

Troubleshooting Green, red, blue, dark and white dots remain. ● The remaining dots are normal characteristic of the liquid crystal used in today’s technology. TV and Audio Problems Poor TV signal reception ● The proximity of mountains or high buildings may be responsible for ghost pictures, echoing or shadows. In this case, try manually adjus[...]

Troubleshooting file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/safety/saf_troub.htm (4 of 4) [3/2/2004 3:44:10 PM][...]

Regulatory Information Regulatory Information TCO '99 Information • TCO Environmental Requirements • CE Declaration of Conformity • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S. Only) • Commission Federale de la Communication (FCC Declaration) • EN 55022 Compliance (Czech Republic Only) • VCCI Cla[...]

Regulatory Information Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric and magnetic fields, energy consumption and electrical and fire safety. The environmental demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) [...]

Regulatory Information The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in[...]

Regulatory Information - EN55022:1998 (Radio Disturbance requirement of Information Technology Equipment) - EN55024:1998 (Immunity requirement of Information Technology Equipment) - EN61000-3-2:2000 (Limits for Harmonic Current Emission) - EN61000-3-3:1995+A1 (Limitation of Voltage Fluctuation and Flicker) - EN55013:2001 (Radio Disturbance requirem[...]

Regulatory Information Power Saving Alternative 2 One step OFF Amber 110VAC < 1W 230VAC < 2W A s an E NERGY S TAR ® P artner, PHILIPS has determined that this product meets the E NERGY S TAR ® guidelines for energy efficiency. We recommend you switch off the monitor when it is not in use for quite a long time. RETURN TO TOP OF THE PAGE Fede[...]

Regulatory Information RETURN TO TOP OF THE PAGE Commission Federale de la Communication (FCC Declaration) Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon à fourir une protection raisonnable contre les int[...]

Regulatory Information RETURN TO TOP OF THE PAGE VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and[...]

Regulatory Information Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All eq[...]

Regulatory Information RETURN TO TOP OF THE PAGE North Europe (Nordic Countries) Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/safety/regs/regulat.htm (9 of 13) [3/2/2004 3:44:12 PM][...]

Regulatory Information Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KO[...]

Regulatory Information Ergonomie Hinweis (nur Deutschland) Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß 1. Reparaturen nur durch Fachpersonal durchgeführt werden. 2. nur original-Ersatzteile verwendet werden. 3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird. Aus ergonomisc[...]

Regulatory Information WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is [...]

Regulatory Information connected to the terminal in the plug which is marked with the letter "E" or by the Earth symbol or coloured GREEN or GREEN AND YELLOW. 2. The BLUE wire must be connected to the terminal which is marked with the letter "N" or coloured BLACK. 3. The BROWN wire must be connected to the terminal which marked [...]

Other Related Information Other Related Information Safety and Troubleshooting • FAQs • Troubleshooting • Regulatory Information • Information for Users in the U. S . • Information for Users Outside the U.S Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT [...]

Philips Pixel Defect Policy Philips Pixel Defect Policy Product Features • Technical Specifications • Resolution & Preset Modes • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Philips' LCD Panel Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the ind[...]

Philips Pixel Defect Policy Types of Pixel Defects Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and several types of sub pixel defects within each category. Bright Dot Defects appear as pixels or sub pixels that are always lit or 'on'. These are the types of bright dot defec[...]

Philips Pixel Defect Policy Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables. BRIGHT DOT DEFECTS ACCEPTABLE LEVEL MODEL 150T4/170T4 1 lit s[...]

Philips Pixel Defect Policy Note: * 1 or 2 adjacent sub pixel defects = 1 dot defect All Philips monitors are ISO13406-2 Compliant RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/product/pixel.htm (4 of 4) [3/2/2004 3:44:20 PM][...]

Connecting to Your PC, TV Antenna, DVD/VCR etc. Connecting to Your PC, TV Antenna, DVD/VCR etc. Front View Product Description • Accessory Pack • Connecting to Your PC, TV Antenna, DVD/VCR etc. • VESA Mounting and Easy Wall Mounting • Installing the Optional TV/AV Module • Getting Started • Optimizing Performance Using the Cable Managem[...]

Connecting to Your PC, TV Antenna, DVD/VCR etc. Mini jack to RCA audio-in cable Audio Chin cable D-SUB to YPbPr adapter cable E-DFU pack TV/AV module Security screw for TV module file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/install/connect.htm (2 of 10) [3/2/2004 3:44:25 PM][...]

Connecting to Your PC, TV Antenna, DVD/VCR etc. Tuner adapter Wall mount kit RETURN TO TOP OF THE PAGE Setting up and connecting your monitor/TV Ensure that the power to the monitor/TV is switched off before the installation. A) Connecting to PC computer file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/install/connect.htm (3 of 10) [3/2/2004 3:44[...]

Connecting to Your PC, TV Antenna, DVD/VCR etc. 1. Make sure the external speaker power cable is plugged into the DC 12V OUT connector on the back of the monitor. 2. Connect the power cord to the AC IN power connector on the back of the monitor. 3. Connect the 15-pin D-SUB of the video signal cable to the VGA connector on the back of the monitor No[...]

Connecting to Your PC, TV Antenna, DVD/VCR etc. 1. Connect RCA (Yellow) or S-VHS cable to an appropriate external AV device such as DVD/VCR. 2. Connect RCA audio cable to AUDIO (R) and AUDIO (L) terminal and the other ends to corresponding audio out terminals on the AV device. 3. Headphone may be connected to the headphone output on the back of the[...]

Connecting to Your PC, TV Antenna, DVD/VCR etc. 1. Using the supplied YPbPr to VGA adapter cable, connect the YPbPr end to the COMPONENT VIDEO OUT terminal of progressive DVD/Setup Box, and connect the other end to the VGA connector on the back of the monitor. 2. Connect the RCA cable to AUDIO (L) and AUDIO (R) to the corresponding audio out termin[...]

Connecting to Your PC, TV Antenna, DVD/VCR etc. 1. Connect an antenna or CATV cable to the antenna port of tuner box. RETURN TO TOP OF THE PAGE Using the Cable Management file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/install/connect.htm (7 of 10) [3/2/2004 3:44:25 PM][...]

Connecting to Your PC, TV Antenna, DVD/VCR etc. 1) Remove the arm box's top cover. Press the center of the cap and open the cap from sides (Do not attempt to open the cap from the top or the bottom) 2) Place the cables inside the arm box. 3) Replace top cover. We recommend you follow intelligent cable management to reduce the electrical altern[...]

Connecting to Your PC, TV Antenna, DVD/VCR etc. 1) Line up in ventilation. Before attempting to seal the cover, make sure it is properly aligned with the upper hooks. 2) Use hands to push and seal in place. To remove back cover file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/install/connect.htm (9 of 10) [3/2/2004 3:44:25 PM][...]

Connecting to Your PC, TV Antenna, DVD/VCR etc. 1) Lift off the rear cover from the top hooks at an angle of less than 30 degrees to avoid hook damage. RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/install/connect.htm (10 of 10) [3/2/2004 3:44:25 PM][...]

VESA Mounting and Easy Wall Mounting VESA Mounting and Easy Wall Mounting Front View Product Description • Accessory Pack • Connecting to Your PC, TV Antenna, DVD/VCR etc. • Installing the Optional TV/AV Module • Getting Started • Optimising Performance Unfold the base • Fold the base • Foldable base available for easy wall mounting ?[...]

VESA Mounting and Easy Wall Mounting Fold the Base 1) Push down the head of monitor. Make sure the back cover is removed when folding the base. Foldable base available for easy wall mounting Make sure the back cover is removed before mounting the monitor on the wall. file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/install/base.htm (2 of 6) [3/2/[...]

VESA Mounting and Easy Wall Mounting Smart tips 1. Use the full scale template to mark on the wall the horizontal distance (130 mm) between the two mounting screws. Notes: - The surface for mounting area must be flat and larger than the pedestal. - The wall must support a pull force of 10 kg for each screw. 2. At the locations marked, drill two hol[...]

VESA Mounting and Easy Wall Mounting WARNING! ● Read all instructions carefully before mounting! ● Correct assembly is essential. The maximum allowed weight of the LCD Display is 6.5 kg/14.3 lbs. ● The assembly materials that come with the product are only suitable for attachment to solid wood, brick or concrete walls. ● For wood walls: Dis[...]

VESA Mounting and Easy Wall Mounting 2) Remove the hinge cape 3) Remove the 4 screws and then remove the base from the LCD monitor. B) Attaching a wall or arm mounting device. file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/install/base.htm (5 of 6) [3/2/2004 3:44:26 PM][...]

VESA Mounting and Easy Wall Mounting Note: This monitor accepts a 100mmx100mm VESA-Compliant mounting interface. The monitor support VESA mounting standard for use with various VESA mounting devices. To install any VESA mounting devices, please follow the instructions given. RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150[...]

Installing the Optional TV/AV Module Installing the Optional TV/AV Module Front View Product Description • Connecting to Your PC, TV Antenna, DVD/VCR etc. • VESA Mounting and Easy Wall Mounting • Getting Started • Optimising Performance Optional TV/AV Module: Detach the TV dummy cover • Install the TV module Detach the TV dummy cover 1) P[...]

Installing the Optional TV/AV Module Install the TV module 1) Press and hold the TV module release button. 2) Slide the TV module towards the center of the monitor until it locks into the monitor. file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/install/module.htm (2 of 3) [3/2/2004 3:44:26 PM][...]

Installing the Optional TV/AV Module 3) Please secure the TV module using the security screw provided. RETURN TO TOP OF THE PAGE file:///D|/My%20documents/dfu/B2C_TV/ENGLISH/150T4/install/module.htm (3 of 3) [3/2/2004 3:44:26 PM][...]

Getting Started Getting Started Front View Product Description • Connecting to Your PC, TV Antenna, DVD/VCR etc. • VESA Mounting and Easy Wall Mounting • Installing the Optional TV/AV Module • Getting Started • Optimizing Performance Getting Started Use the information file ( .inf) for Windows® 95/98/2000/Me/XP or later The built-in VESA[...]

Getting Started For Windows® Me 1. Start Windows® Me 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced...'. 5. Select the 'Monitor' button, then cli[...]

Getting Started 8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button. 9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button. 10. Click on the 'Have disk...' button, then cli[...]

Using other menus (Europe area) Using Other Menus (Europe Area) ● Using the Remote Control ● Selecting a source input ● Adjusting the picture preference ● Adjusting the sound preference ● Selecting a preferred OSD language ● Screen modes ● Automatic tuning • Manual tuning • Skipping programmes Using the Remote Control 1. Press to [...]

Using other menus (Europe area) ● S-video ● HD-YPbPr 4. Press to select the input source. RETURN TO TOP OF THE PAGE Adjusting the picture preference 1. Press to activate the menu. 2. Use , to scroll the highlight PICTURE, and then press . 3. Use , to highlight the picture parameter to be adjusted. There are 5 parameters: ● BRIGHTNESS: adjusts[...]

Using other menus (Europe area) ● SURROUND ON/OFF: to turn the surrounding sound effect on or off. 4. Press , to adjust the selected parameter. 5. Use , to highlight EXIT and then press to exit from the menu. RETURN TO TOP OF THE PAGE Selecting a preferred OSD language 1. Press to activate the menu. 2. Use , to scroll the highlight LANGUAGE, and [...]

Using other menus (Europe area) 4. Press to select the mode. 5. Use , to highlight EXIT and then press to exit from the menu. RETURN TO TOP OF THE PAGE Automatic tuning This menu allows you to automatically search for all the programmes available in your region (or on your cable network). 1. Press to activate the menu. 2. Use , to scroll the highli[...]

Using other menus (Europe area) 4. Use , to scroll the highlight SEARCH and press .The search begins. As soon as a programme is found, the search will stop. If you know the frequency of the programme required, enter its number directly using the 0-9 keys and go to step 6. 5. If reception is unsatisfactory, select FINE TUNE and hold down or key. 6. [...]

Using other menus (AP) Using Other Menus (Asia Pacific Area and China excluding Korea, Taiwan, and Philippines) ● Using the Remote Control ● Selecting a source input ● Adjusting the picture preference ● Adjusting the sound preference ● Selecting a preferred OSD language ● Video mode ● Automatic tuning • Manual tuning • Skipping pr[...]

Using other menus (AP) ● S-video ● HD-YPbPr 4. Press to select the input source. RETURN TO TOP OF THE PAGE Adjusting the picture preference 1. Press to activate the menu. 2. Use , to scroll the highlight PICTURE, and then press . 3. Use , to highlight the picture parameter to be adjusted. There are 6 parameters: ● BRIGHTNESS: alters the brigh[...]

Using other menus (AP) ● BALANCE: to balance the sound between the left and right speakers. ● SURROUND ON/OFF: to turn the surrounding sound effect on or off. 4. Press , to adjust the selected parameter. 5. Use , to highlight EXIT and then press to exit from the menu. RETURN TO TOP OF THE PAGE Selecting a preferred OSD language 1. Press to acti[...]

Using other menus (AP) 5. Use , to highlight EXIT and then press to exit from the menu. RETURN TO TOP OF THE PAGE Automatic tuning This menu allows you to automatically search for all the programmes available in your region (or on your cable network). 1. Press to activate the menu. 2. Use , to scroll the highlight INSTALL, and then press . 3. Use ,[...]

Using other menus (AP) 8. Repeat steps 4 to 7 for each programme to be stored. RETURN TO TOP OF THE PAGE Skipping programmes This menu allows you to set the skipped programmes when you use p +/- keys to access the programme. 1. Press to activate the menu. 2. Use , to scroll the highlight INSTALL, and then press . 3. Use , to scroll the highlight CH[...]

Using other menus (NA) Using Other Menus (Americas, Korea, Taiwan and Philippines) ● Using the Remote Control ● Selecting a source input ● Adjusting the picture preference ● Adjusting the sound preference ● Selecting a preferred OSD language ● Video mode ● Install: Automatic tuning • Manual tuning • Skipping programmes Using the R[...]

Using other menus (NA) ● S-Video ● HD-YPbPr 4. Press to select the input source. RETURN TO TOP OF THE PAGE Adjusting the picture preference 1. Press to activate the menu. 2. Use , to scroll the highlight PICTURE, and then press . 3. Use , to highlight the picture parameter to be adjusted. There are 6 parameters: ● BRIGHTNESS: alters the brigh[...]

Using other menus (NA) ● BALANCE: to balance the sound between the left and right speakers. ● SURROUND ON/OFF: to turn the surrounding sound effect on or off. 4. Press , to adjust the selected parameter. 5. Use , to highlight EXIT and then press to exit from the menu. RETURN TO TOP OF THE PAGE Selecting a preferred OSD language 1. Press to acti[...]

Using other menus (NA) 4. Press to select the mode. 5. Use , to highlight EXIT and then press to exit from the menu. RETURN TO TOP OF THE PAGE Automatic tuning This menu allows you to automatically search for all the programmes available in your region (or on your cable network). 1. Press to activate the menu. 2. Use , to scroll the highlight INSTA[...]

Using other menus (NA) RETURN TO TOP OF THE PAGE Skipping programmes (Channel edit) This menu allows you to set the skipped programmes when you use p +/- keys to access the programme. 1. Press to activate the menu. 2. Use , to scroll the highlight INSTALL, and then press . 3. Use , to scroll the highlight CHANNEL EDIT. 4. Use , keys to view the pro[...]

Your Philips F1rst Choice Warranty Your Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high- quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please co[...]

Your Philips F1rst Choice Warranty standards, which apply in countries for which the product was not originally designed, manufactured, approved and/or authorized. Therefore always check whether a product can be used in a specific country. ● Note that products that are not originally designed, manufactured, approved and/or authorized for usage wi[...]

International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it[...]

United States Guarantee LIMITED WARRANTY (Computer Monitor) Click here to access the Warranty Registration Card . Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange* *Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year. This product must be shipped i[...]

United States Guarantee exclusion of incidental or consequential damages, so the above exclusion may not apply to you. This includes, but is not limited to, prerecorded material, whether copyrighted or not copyrighted.) ● a product used for commercial or institutional purposes. Where IS SERVICE AVAILABLE? Warranty service is available in all coun[...]

United States Guarantee Please contact Philips at: (800) 479-6696 Three years free parts and three years free labor will be provided at Philips Canada depot or any one of its authorized service centers. (In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed or implied, including any implied warranties [...]

Philips Warranty Helpdesk Philips Warranty Helpdesk Telephone numbers: Austria 01 546 575 603 Luxembourg 026 84 3000 Belgium 02 275 0701 Netherlands 053 482 9800 Cyprus (Greek) 800 92256 Norway 22 70 82 50 Denmark 35 25 87 61 Portugal 0800 831 363 France 03 8717 0033 Sweden 08 632 0016 Germany 0696 698 4712 Switzerland 02 23 10 21 16 Greece 00800 3[...]

Consumer Information Centers Consumer Information Centers Antilles • Argentina • Australia • Bangladesh • Brasil • Canada • Chile • China • Colombia • Czech Republic • Dubai • Egypt • Hong Kong • Hungary • India • Indonesia • Korea • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru[...]

Consumer Information Centers RUSSIA Philips Representation Office Ul. Usacheva 35a 119048 Moscow Phone: 095-937 9300 Fax : 095-755 6923 TURKEY Türk Philips Ticaret A.S. Talatpasa Caddesi No 5. 80640-Gültepe/Istanbul Phone: (0800)-211 40 36 Fax : (0212)-281 1809 Latin America ANTILLES Philips Antillana N.V. Kaminda A.J.E. Kusters 4 Zeelandia, P.O.[...]

Consumer Information Centers CHILE Philips Chilena S.A. Avenida Santa Maria 0760 P.O. box 2687Santiago de Chile Phone: (02)-730 2000 Fax : (02)-777 6730 COLOMBIA Industrias Philips de Colombia S.A.-Division de Servicio CARRERA 15 Nr. 104-33 Bogota, Colombia Phone:(01)-8000 111001 (toll free) Fax : (01)-619-4300/619-4104 MEXICO Consumer Information [...]

Consumer Information Centers URUGUAY Ind.Philips del Uruguay S.A. Luis Alberto de Herrera 1248 Customer Help Desk 11300 Montevideo Phone: (02)-6281111 Fax : (02)-6287777 VENEZUELA Industrias Venezolanas Philips S.A. Apartado Postal 1167 Caracas 1010-A Phone: (02) 2377575 Fax : (02) 2376420 Canada CANADA Philips Electronics Ltd. 281 Hillmount Road M[...]

Consumer Information Centers NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O. box 1041 Auckland Phone: 0800 477 999 (toll free) Fax : 0800 288 588 (toll free) Asia BANGLADESH Philips Service Centre 100 Kazi Nazrul Islam Avenue Kawran Bazar C/A Dhaka-1215 Phone: (02)-812909 Fax : (02)-813062 CHINA BEIJING Beiji[...]

Consumer Information Centers 200001 Shanghai Phone: 800 820 5128 (toll free) Fax: 21-656 10647 HONG KONG Philips Hong Kong Limited Consumer Information Centre 16/F Hopewell Centre 17 Kennedy Road, WANCHAI Phone: 2619 9663 Fax : 2481 5847 INDIA Phone: 91-20-712 2048 ext: 2765 Fax: 91-20-712 1558 BOMBAY Philips India Customer Relation Centre Bandbox [...]

Consumer Information Centers INDONESIA Philips Group of Companies in Indonesia Consumer Information Centre Jl.Buncit Raya Kav. 99-100 12510 Jakarta Phone: (021)-794 0040 / 798 4255 ext: 1612 Fax : (021)-794 7511 / 794 7539 KOREA Philips Korea Ltd. Philips House C.P.O. box 3680 260-199, Itaewon-Dong. Yongsan-Ku, Seoul 140-202 Phone:080-600-6600 (Loc[...]

Consumer Information Centers PHILIPPINES Philips Electronics and Lighting Inc. 106 Valero St., Salcedo Village Makati, Metro Manilla. Phone: (02)-888 05 72 Domestic toll free: 1-800-10-PHILIPS or 1-800-10-744 5477 Fax : (02)-888 05 71 SINGAPORE Philips Singapore Private Ltd. Consumer Service Dept. Lorong 1,Toa Payoh., P.O. box 340 Singapore 1231 Ph[...]

Consumer Information Centers MOROCCO Philips Electronique Maroc 304,BD Mohamed V Casablanca Phone: (02)-302992 Fax : (02)-303446 SOUTH AFRICA South African Philips. S.V. Div. 195 Main R.D. Martindale., Johannesburg P.O.box 58088 Newville 2114 Phone: +27 11 471 5000 Fax : +27 11 471 5020 Middle East DUBAI Philips Middle East B.V. Consumer Informatio[...]