Philips 180B2P manual

Philips 180B2P Electronic User's Manual file:///D|/Grace/K1/english/180b2p/index.htm [6/2/2002 5:22:06 PM][...]

Safety and Troubleshooting Information Safety Precautions and Maintenance • Installation Locations • FAQs • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to [...]

Installation Locations Avoid Heat and Extreme Cold ● Do not store or use the LCD monitor in locations exposed to heat, direct sunlight, or extreme cold. ● Avoid moving the LCD monitor between locations with large temperature differences. Choose a site falling within the following temperature and humidity ranges. Temperature: 5-35°C 41-95°F ?[...]

About This Manual About This Guide • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the LCD monitor's features, setup, operation and other pertinent information. Its contents are identical to the information in our printed version. Sections are [...]

CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data. WARNING: This icon indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of th[...]

Product Information Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views • Physical Function Product Features 180B2P 18-inch color LCD monitor with excellent display performance ● Thinnest front b[...]

VIDEO • Video dot rate 135MHz • Input impedance - Video 75 Ohm - Sync 2K Ohm • Input signal levels 0.7 Vpp • Sync input signal Separate sync Composite sync Sync on green • Sync polarities Positive and negative • Video interface D-Sub (analog) Optical characteristics • Contrast ratio: 350 (typ.) • Brightness: 250 cd/m 2 (typ.) • Pe[...]

32 user definable modes 15 factory preset modes: H. freq (kHz) Resolution V. freq (Hz) 31.5 640*350 70 (IBM VGA 10h) 31.5 720*400 70 31.5 640*480 60 35.0 640*480 67 37.5 640*480 75 35.2 800*600 56 37.9 800*600 60 46.9 800*600 75 49.7 832*624 75 48.4 1024*768 60 60.0 1024*768 75 69.0 1152*870 75 71.8 1152*900 76 (SUN Mode II) 63.9 1280*1024 60 80 12[...]

ON Active Yes Yes < 60W Green Stand-by Blanked No Yes < 2W Amber Suspend Blanked Yes No < 2W Amber OFF Blanked No No < 2W Amber This monitor is E NERGY S TAR ® compliant. A s an E NERGY S TAR ® P artner, PHILIPS has determined that this product meets the E NERGY S TAR ® guidelines for energy efficiency. RETURN TO TOP OF THE PAGE Phys[...]

Pin No. Assignment Pin No. Assignment 1 Red video input 9 +5V 2 Green video input/SOG 10 Logic ground 3 Blue video input 11 Identical output - connected to pin 10 4 Sense (GND) 12 Serial data line (SDA) 5 Not connected 13 H. Sync / H+V 6 Red video ground 14 V. Sync (VCLK for DDC) 7 Green video ground 15 Data clock line (SCL) 8 Blue video ground RET[...]

1) Tilt 2) Swivel 3) Portrait display Turn monitor from landscape view to portrait view 3.1) Tilt the monitor body at an angle 180B2P Product Information file:///D|/Grace/K1/english/180b2p/product/product.htm (6 of 7) [6/2/2002 5:22:11 PM][...]

3.2) Rotate the monitor body 90 degrees counter clockwise. RETURN TO TOP OF THE PAGE 180B2P Product Information file:///D|/Grace/K1/english/180b2p/product/product.htm (7 of 7) [6/2/2002 5:22:11 PM][...]

Installing your LCD Monitor Your LCD Monitor : Front View Product Description • Connecting to Your PC • Remove and re-install the base • Getting Started • Optimizing Performance • Accessories (optional) Front View Product Description UP and DOWN buttons are used when adjusting the OSD of your monitor LEFT and RIGHT buttons, like the UP an[...]

POWER button switches your monitor on Automatically adjust the horizontal position, vertical position, phase and clock setting. RETURN TO TOP OF THE PAGE Rear View AC power in 1. DC 12V out for Philips Multimedia Base only 2. D-SUB Connector 3. RETURN TO TOP OF THE PAGE Installing your LCD Monitor file:///D|/Grace/K1/english/180b2p/install/install.[...]

Optimizing Performance For best performance, ensure that your display settings are set at 1024x768@60Hz (for 14"/15") or 1280x1024, 60Hz (for 17"/18"). ● Note: You can check the current display settings by pressing the "OK" button once. Go into the Product Information. The current display mode is shown on the item ca[...]

On-Screen Display Description of the On-Screen Display • The OSD Tree Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips LCD monitors which allows an end-user to adjust screen performance of monitors directly though an on-screen instruction window. The user interface provides user-friendliness and[...]

On-Screen Display file:///D|/Grace/K1/english/180b2p/osd/osddesc.htm (2 of 3) [6/2/2002 5:22:16 PM][...]

RETURN TO TOP OF THE PAGE On-Screen Display file:///D|/Grace/K1/english/180b2p/osd/osddesc.htm (3 of 3) [6/2/2002 5:22:16 PM][...]

Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EAS[...]

Glossary A B C D E F G H I J K L M N O P Q R S T U V W X Y Z C Color temperature A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of a black body radiating with the same dominant frequency as the source. Most Philips monitors offer the possibility of setting the color temperature to any desired val[...]

E Energy Star Computers Programme An energy conservation programme launched by the US Environmental Protection Agency (EPA) with the primary aim of promoting the manufacture and marketing of energy-efficient office automation equipment. Companies joining this programme must be willing to commit themselves to manufacturing one or more products capab[...]

A Universal Serial Bus device that provides additional connections to the Universal Serial Bus. Hubs are a key element in the plug-and-play architecture of USB. The Figure shows a typical hub. Hubs serve to simplify USB connectivity from the user's perspective and provide robustness at low cost and complexity. Hubs are wiring concentrators and[...]

Upstream The direction of data flow towards the host. An upstream port is the port on a device electrically closest to the host that generates upstream data traffic from the hub. Upstream ports receive downstream data traffic. RETURN TO TOP OF THE PAGE V Vertical refresh rate Expressed in Hz, it is the number of frames (complete pictures) written t[...]

FAQs (Frequently Asked Questions) Safety and Troubleshooting • General FAQ • Screen Adjustments • Compatibility with Other Peripherals • LCD Panel Technology • Ergonomics, Ecology, and Safety Standards • Troubleshooting • Regulatory Information • Other Related Information General FAQs Q: When I install my monitor how do I do if the [...]

Q: What does "refresh rate" mean to me in an LCD monitor? A: For LCD monitors, the refresh rate is much less relevant. LCD monitors display a stable, flicker-free image at 60Hz. There is no visible differences between 85Hz and 60Hz. Q: What are the .inf and .icm files on the setup disk & CD-ROM? How do I install the drivers (.inf and [...]

Q: Does Refresh Rate mean to LCD? A: Unlike CRT display technology in which the speed the electron beam is swept from the top to the bottom of the screen determines flicker, an active matrix display uses an active element (TFT) to control each individual pixel and thus refresh rate is not really applicable to LCD technology. Q: Will the LCD screen [...]

Q: When I install my monitor, how do I get the best performance for the monitor? A: For best performance, make sure your display settings are set at 1024x768@60Hz for 14"/15", 1280x1024@60Hz for 17"/18". Note: You can check the current display settings by pressing the OSD OK button once. The current display mode is shown in prod[...]

adjustment of complicated IRQ settings -- for add-on peripherals. USB does away with "port gridlock." Without USB, PCs are normally limited to one printer, two Com port devices (usually a mouse and modem), one Enhanced Parallel Port add-on (scanner or video camera, for example), and a joystick. More and more peripherals for multimedia com[...]

Q: What differentiates passive matrix LCDs from active matrix LCDs? A: An LCD is made with either a passive matrix or an active matrix display grid. An active matrix has a transistor located at each pixel intersection, requiring less current to control the luminance of a pixel. For this reason, the current in an active matrix display can be switche[...]

Q: What kind of wide-angle technology is available? How does it work? A: The TFT LCD panel is an element controls/displays inlet of a backlight using the dual-refraction of liquid crystal. Using the property that the projection of inlet light refracts toward the major axis of the liquid element, it controls the direction of inlet light and displays[...]

A: Yes. Philips LCD monitors conform to the guidelines of MPR-II and TCO 95-99 standards for the control of radiation, electromagnetic waves, energy reduction, electrical safety in the work environment, and recyclability. The specification page provides detailed safety standards data. More information is provided in the Regulatory Information chapt[...]

Troubleshooting Safety and Troubleshooting • FAQs • Common Problems • Imaging Problems • Regulatory Information • Other Related Information This page presents problems that can be corrected by the user. If the problem still exists after these possible solutions, contact your nearest Philips dealer. Common Problems Having this problem? Che[...]

The screen is too bright or too dark Adjust the contrast and brightness in OSD Main Controls. (The backlight of the LCD monitor has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer. ● An after-image appears If an image remains in the screen for an extended period of time, it may be imprinted in the [...]

Regulatory Information TCO '95 Information • TCO Environmental Requirements • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S. Only) • Commission Federale de la Communication (FCC Declaration) • EN 55022 Compliance (Czech Republic Only) • VCCI Class 2 Notice (Japan Only) • MIC Notice (South Korea Onl[...]

be ordered from: TCO Development Unit SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO'95 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ TCO'95 is a co-operative project between TCO (The Swedish Confede[...]

CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on Earth of ultraviolet light with consequent increased risks of skin cancer (malignant melanoma). The relevant TCO&apo[...]

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from t[...]

RETURN TO TOP OF THE PAGE VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment acco[...]

Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works toge[...]

Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILF?[...]

RETURN TO TOP OF THE PAGE End-of-Life Disposal Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of. Please find out about the local regulations on how to dispose of your old monitor from your loca[...]

or coloured GREEN or GREEN AND YELLOW. 2. The BLUE wire must be connected to the terminal which is marked with the letter "N" or coloured BLACK. 3. The BROWN wire must be connected to the terminal which marked with the letter "L" or coloured RED. Before replacing the plug cover, make certain that the cord grip is clamped over th[...]

Other Related Information Safety and Troubleshooting • FAQs • Troubleshooting • Regulatory Information • Information for Users in the U. S . • Information for Users Outside the U.S Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a max[...]

Philips Pixel Defect Policy Product Features • Technical Specifications • Resolution & Preset Modes • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Philips' Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most [...]

One lit red, green or blue subpixel Two adjacent lit subpixels: - Red + Blue = Purple - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) Three adjacent lit subpixels (one white pixel) Black Dot Defects Black dot defects appear as pixels or subpixels that are always dark or "off". These are the types of black dot defects: One dark s[...]

Distance between two bright dot defects* 0 0 15 mm or more 15 mm or more 15 mm or more 15 mm or more Bright dot defects within 20 mm circle 0 0 3 or fewer 3 or fewer 3 or fewer 3 or fewer Total bright dot defects of all types 0 0 8 or fewer 4 or fewer 8 or fewer 3 or fewer BLACK DOT DEFECTS ACCEPTABLE LEVEL MODEL 150P2 150B2 150S2 170B2 170S2 180P2[...]

RETURN TO TOP OF THE PAGE Philips Pixel Defect Policy file:///D|/Grace/K1/english/180b2p/product/pixel.htm (4 of 4) [6/2/2002 5:22:40 PM][...]

Connecting to Your PC Your LCD Monitor : Front View Product Description • Accessory Pack • Connecting to Your PC • Remove and re-install the base • Getting Started • Optimizing Performance • Accessories (optional) Accessory Pack Unpack all the parts. Item Description 180B2S 180B2W 180P2M 180P2G 180P2B 180B2P 1) Audio in Cable (Option on[...]

5) VGA Signal Cable v v v v 6) DVI to D-Sub Signal Cable v v 7) E-DFU package with Quick Setup Guide, Using Your Monitor Manual, and CD-ROM. v v v v 8) Pivot CD-ROM v v RETURN TO TOP OF THE PAGE Connecting to Your PC 1) Thread power cable through the hole at the bottom of the base, and plug onto monitor firmly. 2) Double check all cables' conn[...]

Note: If you use an Apple Macintosh, you need to connect the special Mac adapter to one end of the monitor signal cable Connecting to Your PC file:///D|/Grace/K1/english/180b2p/install/connect.htm (3 of 4) [6/2/2002 5:22:46 PM][...]

3) Connect to PC (a) Turn off your computer and unplug its power cable. (b) Connect the monitor signal cable to the video connector on the back of your computer. (c) Plug the power cord of your computer and your monitor into a nearby outlet. (d) Turn on your computer and monitor. If the monitor displays an image, installation is complete. RETURN TO[...]

Remove and Re-install the Base Your LCD Monitor : Front View Product Description • Accessory Pack • Connecting to Your PC • Getting Started • Optimizing Performance • Accessories (optional) Remove and Re-install the Base : Remove the base • Re-install the base Condition: for VESA standard mounting applications ● for optional bases rep[...]

3) Unscrew the four screws of the base RETURN TO TOP OF THE PAGE Re-install the Base 1) Put monitor face down on the safe surface and plug in the cables into connectors. 2) Mount the base onto the monitor body and fix four screws securely. Remove and re-install the base file:///D|/Grace/K1/english/180b2p/install/base.htm (2 of 3) [6/2/2002 5:22:46 [...]

3) Lift the monitor body and thread all cables through the hole at the bottom of the base. RETURN TO TOP OF THE PAGE Remove and re-install the base file:///D|/Grace/K1/english/180b2p/install/base.htm (3 of 3) [6/2/2002 5:22:46 PM][...]

Getting Started Your LCD Monitor : Front View Product Description • Connecting to Your PC • Remove and Re-install the Base • Getting Started • Optimizing Performance • Accessories (optional) Getting Started Use the information file ( .inf) for Windows 95/98/2000/Me/XP or later Philips' monitors built in VESA DDC2B feature to support [...]

Start Windows Me 1. Click the 'Start' button, point to 'Settings', and then click 'Control Panel'. 2. Double Click the 'Display' Icon. 3. Choose the 'Settings' tab then click 'Advanced...'. 4. Choose 'Monitor' button, then click 'Change...' button. 5. Choose "Speci[...]

Choose the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button. 8. Choose the ' Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button. 9. Click the 'Have disk...' button then click the 'Browse...&[...]

Accessories (optional) Your LCD Monitor : Front View Product Description • Connecting to Your PC • Remove and re-install the base • Getting Started • Optimizing Performance Accessories (optional): USB Hub • Protective Cover • Multimedia Base Accessories (optional) Item Description 170B2 170S2 180B2 180P2 USB Hub: (PCUH411) USB hub suppo[...]

Multimedia Base: (VG3P31) 2x2W RMS, 48W PMPO, stereo front firing & portrait display, tilt & swivel. Height adjustable. Color: Light gray v v Multimedia Base: (VG3P32) 2x2W RMS, 48W PMPO, stereo front firing & portrait display, tilt & swivel. Height adjustable. Color: Black v v RETURN TO TOP OF THE PAGE USB Hub Accessories (optional[...]

Take off the cover. Slide into USB tray on rear side of base. RETURN TO TOP OF THE PAGE Protective Cover Protect the LCD screen of your Philips LCD monitor Accessories (optional) file:///D|/Grace/K1/english/180b2p/install/access.htm (3 of 8) [6/2/2002 5:22:48 PM][...]

1) Remove the screw from the rear of monitor 2) Unclick at the indicated points to open the bezel 3) Pull forward to release the bezel completely Accessories (optional) file:///D|/Grace/K1/english/180b2p/install/access.htm (4 of 8) [6/2/2002 5:22:48 PM][...]

4) Peel off the film from both sides of the protective cover 5) Mount the protective cover and press each corner to attach it securely 6) Fix the screw onto the rear of monitor RETURN TO TOP OF THE PAGE Multimedia Base Accessories (optional) file:///D|/Grace/K1/english/180b2p/install/access.htm (5 of 8) [6/2/2002 5:22:48 PM][...]

1) Put monitor face down on the safe surface and plug in the cables into connectors. 2) Mount the base onto the monitor body and fix four screws securely. 3) Lift the monitor body and thread all cables through the hole at the bottom of the base. Accessories (optional) file:///D|/Grace/K1/english/180b2p/install/access.htm (6 of 8) [6/2/2002 5:22:48 [...]

4) For Multimedia base, plug the flying DC power cable of base onto monitor. 5) Thread power cable through the hole at the bottom of the base, and plug onto monitor firmly. 6) Connect microphone and audio cables onto the rear side of base if any. Accessories (optional) file:///D|/Grace/K1/english/180b2p/install/access.htm (7 of 8) [6/2/2002 5:22:48[...]

7) Connect to PC (a) Turn off your computer and unplug its power cable. (b) Connect the monitor signal cable to the video connector on the back of your computer. (c) Connect the audio and microphone cables to the audio and mic connectors on the back of your computer. (d) Plug the power cord of your computer and your monitor into a nearby outlet. (e[...]

Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly[...]

Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a pe[...]

LIMITED WARRANTY (Computer Monitor) Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange* *Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year. This product must be shipped in at your expense for service during years two and three. WHO IS COVERED? You [...]

Philips service organization will attempt to provide service (although there may be a delay if the appropriate spare parts and technical manual(s) are not readily available). Where CAN I GET MORE INFORMATION? For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A. customers only) or (903) 242-4804 . Before R[...]

Philips Customer Care Center, P. O. Box 2976, Longview, TX 75601 Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while [...]

F1rst Choice Contact Information Telephone numbers: Austria 01 546 575 603 Luxembourg 408 443 5501 Belgium 02 275 0701 Netherlands 053 482 9800 Cyprus (Greek) 800 92256 Norway 22 70 82 50 Denmark 35 25 87 61 Portugal 0800 831 363 France 03 8717 0033 Sweden 08 632 0016 Germany 0696 698 4712 Switzerland 02 23 10 21 16 Greece 00800 3122 1223 Spain 09 [...]

Consumer Information Centers Antilles • Argentina • Australia • Bangladesh • Brasil • Canada • Chile • China • Colombia • Czech Republic • Dubai • Egypt • Hong Kong • Hungary • India • Indonesia • Korea • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru • Philippines • Poland ?[...]

ANTILLES Philips Antillana N.V. Kaminda A.J.E. Kusters 4 Zeelandia, P.O. box 3523-3051 Willemstad, Curacao Phone: (09)-4612799 Fax : (09)-4612772 ARGENTINA Philips Antillana N.V. Kaminda A.J.E. Kusters 4 Zeelandia, P.O. box 3523-3051 Willemstad, Curacao Phone: (01)-544 2047 BRASIL Philips da Amazônia Ind. Elet. Ltda. Centro de Informações ao Con[...]

PARAGUAY Philips del Paraguay S.A. Avenida Artigas 1519 Casilla de Correos 605 Asuncion Phone: (021)-211666 Fax : (021)-213007 PERU Philips Peruana S.A. Customer Desk Comandante Espinar 719 Casilla 1841 Limab18 Phone: (01)-2412890 Fax : (01)-2412913 URUGUAY Ind.Philips del Uruguay S.A. Avenida Uruguay 1287 Customer Help Desk 11100 Montevideo Phone:[...]

NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O. box 1041 Auckland Phone: 0800 477 999 (toll free) Fax : (09)-8497858 Asia BANGLADESH Philips Service Centre 100 Kazi Nazrul Islam Avenue Kawran Bazar C/A Dhaka-1215 Phone: (02)-812909 Fax : (02)-813062 CHINA BEIJING Beijing Authorized Service Centre. Consumer In[...]

HONG KONG Philips Hong Kong Limited Consumer Information Centre 16/F Hopewell Centre 17 Kennedy Road, WANCHAI Phone: 2619-9663 Fax : 2861-3104 INDIA PUNE Phone: 91-20-7122048 BOMBAY Philips India Customer Relation Centre Bandbox House 254-D Dr. A Besant Road, Worli Bombay 400 025 Phone: (022)-4926611 Fax : (022)-4941698 CALCUTTA Customer Relation C[...]

KOREA Philips Korea Ltd. Philips House C.P.O. box 3680 260-199, Itaewon-Dong. Yongsan-Ku, Seoul 140-202 Phone:080-060-6600(toll free) Fax : (02)-5959688 MALAYSIA Philips Malaysia Sdn. Berhad Service Dept. No.51,sect.13 Jalan University. 46200 Petaling Jaya, Selagor. P.O.box 12163 50768 Kuala Lumpur. Phone: (03)-7950 5501 Fax : (03)-7955 6214 PAKIST[...]

TAIWAN Philips Taiwan Ltd. Consumer Information Centre Nr 96 Section 1, Chien-Kuo N.Road TAIPEI Phone: (02)-2382-4567 Fax : (02)-2134-2670 THAILAND Philips Electronics (Thailand) Ltd. Philips Service Centre 209/2 Sanpavut Road, Bangna, Bangkok 10260 Phone : (02)-3983691 Fax : (02)-3983319 Africa MOROCCO Philips Electronique Maroc 304,BD Mohamed V C[...]

EGYPT Philips Egypt Consumer Information Centre 10, Abdel Rahman El Rafei Mohandessin - Cairo, P.O.Box 242 DOKKI Phone: (02)-3313993 Fax : (02)-3492142 Consumer Information Centers file:///D|/Grace/K1/english/warranty/warcic.htm (8 of 8) [6/2/2002 5:23:08 PM][...]

Download and Print Installing your LCD monitor driver • Download and Printing Instructions • Installing FPadjust Program Installing Your LCD monitor driver System requirements: PC running Windows 95, Windows 98, Windows 2000 , Windows Me, Windows XP or later ● Find your driver ".inf/.icm/.cat" at : /PC/drivers/ ● Read the "Dr[...]

Download 180B2P.pdf Download 180B2S.pdf Download 180B2W.pdf Download 180P2M.pdf Download 180P2G.pdf Download 180P2B.pdf Download 200P3G.pdf Download 200P3M.pdf 2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to Disk'. 3. Choose where you would like to save the file; click [...]

System requirements: PC running Windows 95, Windows 98, Windows 2000, Winodws Me, Windows XP or later ● To install FPadjust Program : Click on the link or icon to install FPadjustment Program. or ● Click-and-hold your mouse over the icon. (Win95/98/2000/Me/XP users right-click) ● Download FP_setup02.exe From the menu that appears, choose &apo[...]