Planar PX2210MW manual

[...]

[...]

1[...]

The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photo[...]

3[...]

For your safety------------------------------------------------------ 5 Safety precautions -------------------------------------------6 Special notes on lcd monitors -----------------------------7 Before you operate the monitor --------------------------------7 Features --------------------------------------------------------7 Packing list --------[...]

 Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC C lass B Radio F requency Interference S tatement W A R N I N G: ( FO R FCC CE R T I F I E D M O D ELS ) NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Pa[...]

PR ECAUT I ONS z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufac[...]

 S P EC I AL NOTES ON LC D M ON I TO R S The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES x Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. x You may find slightly uneven brightnes[...]

I NSTALLAT I ON I NST R UCT I ONS BASE the sti c k. Insert thin sti c k into ho l e,Pu ll the stand whi l e push base. Press and ho l d the hooks inside,and pu ll the stand- monitor f l at on a tab l e with front fa c e down. prevent the monitor from being s c rat c hed.Lay the Put a pie c e of soft cl oth on the tab l e beforehand to Insta ll the [...]

 CONT R OLS AN D CONNECTO R S S IG NAL CABLE C onnecting the S ignal C a b l e : Plug one end of the signal cable to the LCD monitor and the other end to a computer or a video source. C onnecting the Power C ord: Plug the AC-power cord one end to LCD monitor’s AC input socket , the other end to Wall outlet. C onnecting the A udio C a b le: Con[...]

A DJ UST I N G T H E VI E WI N G AN G LE x For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. x Hold the stand so you do not toppl e the monitor when you change the monitor’s angle. x You are able to adjust the monitor’s angle from -5 q to 19 q . Figure 3 NOTE[...]

 G ENE R AL I NST R UCT I ONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. x The power cord should be connected. x Connect the video cable from the monitor to the video[...]

F R ONT P ANEL CONT R OL x Power B utton: Press this button to switch ON/OFF monitor’s power. x P ower Indicator : Blue --- Power On mode. Orange --- Power saving mode . x Activates OSD menu or function adjust confirm . x Activates the ECO control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when fu[...]

 H O W TO A DJ UST A SETT I N G 1. Press the MENU-button to activate the OSD window. 2. Press + or - to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press + or - again to navigate through the sub-menu functions. Once the desired function i[...]

 14 ADJUSTING THE PICTURE Main Menu Item Main Menu Icon Sub Menu Description Enhances Contrast Ratio Note: When this function is turned "On" you cannot adjust the current settings for Contrast, Brightness, ECO mode or Gamma. (VGA input only) (VGA input only) (VGA input only) (VGA input only)[...]

Main Menu Item Main Menu Icon S u b Menu Description 15[...]

Main Menu Item Main Menu Icon S u b Menu Description 16[...]

17 Main Menu Item Main Menu Icon Sub Menu Description[...]

P LU G AN D P LAY Plug & Play DD C 2 B F eature This monitor is equipped with VESA DDC 2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC 2B is a bidirectional data [...]

 TEC H N I CAL SU PP O R T ( FA Q) Pro b lem & Question Possi b le S olution Power LED is not on *Check if the Power Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video [...]

E RR O R M ESSA G E & P OSS I BLE SOLUT I ON NO S IG NAL : 1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. I N P UT NOT SU PP O R T : Your computer has been set to unsuitable display mode ,set the computer to display mod[...]

 A PP EN DIX S P EC I F I CAT I ONS LCD Panel Driving system TFT 21. 5 "Color LCD Viewable Image Size 546 mm diagonal Pixel pitch 0.248 ˄ H ˅ × 0.248 ˄ v ˅ 0. 2kg Input Video R, G, B Analog Interface DVI HDMI Separate Sync. H/V TTL H-Frequency Analog:24-80kHz,Digital:30kHz– 83 kHz V-Frequency Analog&Digital: 56 - 76 Hz Dot Clock [...]

 FACTO R Y PR ESET T IMI N G TABLE 640 x 480 31.469 59.94 640 x 480 35 66.667 VGA 640 x 480 37.861 72.809 Mac VGA 640 x 480 37.5 75 Dos-mode 720 x 400 31.469 70.087 800 x 600 35.156 56.25 800 x 600 37.879 60.317 800 x 600 48.077 72.188 SVGA 800 x 600 46.875 75 Mac SVGA 832 x 624 49.726 74.551 1024 x 768 48.363 60.004 1024 x 768 56.476 70.069 102[...]

CONNECTO R PI N ASS IG N M ENT 15 6 10 11 15 15 - Pin Color Display Signal Cable PI N NO . D ESC RIP T I ON PI N NO . D ESC RIP T I ON 1. Red 9. +5V 2. Green 10. Detect Cable 3. Blue 11. Ground 4. Ground 12. DDC-Serial Data 5. Ground 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground 24 - Pin Color Display Signal Cable P[...]

 Pin N o. S ignal N ame Pin N o. S ignal N ame Pin N o. S ignal N ame 1 TMDS Data 2+ 9 TMDS Data 0 17 DDC/CEC Ground 2 TMDS Data 2 Shield 10 TMDS Clock + 18 +5V Power 3 TMDS Data 2 11 TMDS Clock Shield 19 Hot Plug Detect 4 TMDS Data 1+ 12 TMDS Clock 5 TMDS Data 1Shield 13 CEC 6 TMDS Data 1 14 Reserved (N.C. on device 7 TMDS Data 0+ 15 SCL 8 TMDS[...]

Product Registration and T echnical S upport Register Y our Planar Products T oday Thank you choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your productat http://www.planar.com/support/product_registration.html C a b les, Replacement L am[...]

[...]

[...]

[...]

[...]

Q41G2201935 2 C[...]