Poulan Pro 414659 manual

OWNER'S MANUAL MODEL NUMBER: PP10530ES SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury . 414659 Rev 1 09.21.07 TH Printed in the U.S.A.[...]

2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e[...]

3 CONGRA TUL A TIONS on your purchase of a new snow thrower . It has been designed, engineered and man u fac - tured to give best possible dependability and per for mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center . We have competent, well-trained tech ni cians and the proper [...]

4 P ARTS P ACKED SEP ARA TEL Y IN CARTON AS SEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow th[...]

5 AS SEMBL Y / PRE-OPERA TION NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely . INST ALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. Remove plastic tie securing ro[...]

6 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TOR HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower . 2. Position chute rotator head over chute bracket. If[...]

7 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING Y OUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in litera[...]

8 OPERA TION Throttle/engine control - used to se lect either F AST or SL OW engine speed and to STOP the engine. T raction drive control lever - used to engage power-pro- pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow). Discharge chute control lever - used to change the di- rec tio[...]

9 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just - ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles. HOW TO USE Y[...]

10 OPERA TION TO THROW SNOW (See Fig. 14) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow . TO MOVE FORWARD AND BACK WARD (See Fig. 16) SELF-PROPELLING, forward and re[...]

11 TO ADJUST SKID PL A TES (See Fig. 17) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow [...]

12 OPERA TION COLD ST ART - ELECTRIC ST ARTER 1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key . Keep the extra safety ignition key in a safe place. 2. Place throttle control in FAST position. 3. Rotate choke control to FULL position. 4. Connect the power cord to the engine. 5. P[...]

13 GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad just ments will need to be made periodically to properly maintain your snow thrower .[...]

14 MAINTENANCE AUGER GEAR CASE • The gear case was filled with lubricant to the proper level at the factory . The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease. TRACTION DRIVE SYSTEM DO NOT lubricate the drive components inside the snow thrower [...]

15 CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower . 4. Connect spark plug wire to spark plug. Replace safety ignition key . WARNING: T o avoid serious injury , before performing any service or ad just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3.[...]

16 BEL T KEEPER IDLER ARM SQUARE HOLE BOL T TRACTION DRIVE BEL T CLUTCHING IDLER ARM BRACKET AUGER BEL T FL A T WASHER AUGER PULLEY AUGER HOUSING FRAME ENGINE PULLEY L OCKWASHER BOL T FIG. 21 SERVICE AND ADJUSTMENTS 1. REMOVE GASOLINE FROM FUEL T ANK - Drain gasoline from fuel tank into a suitable container , out- doors, away from fire or flame. Wi[...]

17 SERVICE AND ADJUSTMENTS STORAGE Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or ga[...]

18 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position. 4. Move throttle to F AST position. 5. Choke in OFF position. 5. Move to FULL position. 6. [...]

19 SERVICE NOTES[...]

20 REP AIR P AR TS SNOW THROWER - MODEL PP10530ES (96192001800) AUGER HOUSING / IMPELLER ASSEMBL Y 6 6 5 9 9 12 7 7 8 6 11 57 10 13 4 14 16 15 36 37 50 47 42 42 44 27 27 43 43 46 38 45 41 40 39 34 32 49 19 48 51 33 35 56 30 31 19 19 55 26 10 22 25 20 18 58 25 26 29 20 10 17 17 28 55 28 18 58 07 AIG plug_r1[...]

21 KEY P ART NO . NO. DESCRIPTION 4 191079 Pulley , Impeller 5 188909 Bearing Assembly , Flange 6 155377 Nut, Hex Flange 5/16-18 7 180355 Bolt, Flat Head, Carriage 5/16-18 x 5/8 8 72270505 Bolt, Carriage 5/16-18 9 163183 Bolt, Hex Head 10 404930X428 Housing, Auger 11 404933X428 Bar , Scraper 12 178675X008 Bracket, Corner Discharge 13 175322 Base, D[...]

22 REP AIR P AR TS SNOW THROWER - MODEL PP10530ES (96192001800) CONTROL P ANEL / DISCHARGE CHUTE 3 2 1 2 6 19 2 2 26 28 27 27 25 20 29 7 4 5 6 8 8 16 18 17 10 14 3 13 15 9 11 12 22 23 22 23 31 32 30[...]

23 REP AIR P AR TS SNOW THROWER - MODEL PP10530ES (96192001800) CONTROL P ANEL / DISCHARGE CHUTE KEY P ART NO . NO. DESCRIPTION 1 414280 Knob, Lever 2 17501010 Screw #10-24 x 5/8 3 198475 Control Assembly , Deflector 4 73800600 Nut, Lock 3/8-16 5 19131316 Washer , Flat 3/8 6 404974 Control Assembly , Chute Rotater 7 405784X479 Support, Pivot 8 1500[...]

24 REP AIR P AR TS SNOW THROWER - MODEL PP10530ES (96192001800) HANDLES 32 31 32 30 31 12 10 11 13 15 15 11 16 17 16 23 22 27 27 22 17 11 15 15 14 38 39 40 7 6 36 2 5 5 1 4 4 4 4 8 28 28 9 18 19 26 24 24 25 5 5 37 33 35 35 34 34 42 43 44 45 46 46 handles4-interlock-light-T ec_no bend_2[...]

25 KEY P ART NO . NO. DESCRIPTION 1 405999X479 Lever , Auger Control, RH 2 405783X479 Lever , T raction Drive Control 4 178888 Bushing, Flange 5 169675 Retainer , Hairpin 6 17060408 Screw , Hex Head 1/4-20 x 3/4 7 178652 Rod, Interlock 8 196333X008 Arm, Impeller Rod 9 196334X008 Arm, T raction Rod 10 196619X479 P anel, Control 11 74780524 Screw , H[...]

26 REP AIR P AR TS SNOW THROWER - MODEL PP10530ES (96192001800) DRIVE 4 4 4 4 4 2 2 43 11 1 1 22 5 5 5 2 2 20 41 21 17 13 3 6 14 19 18 18 15 24 36 35 34 37 31 9 12 23 26 29 25 4 4 33 28 32 27 44[...]

27 REP AIR P AR TS SNOW THROWER - MODEL PP10530ES (96192001800) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO. DESCRIPTION 1 401619[...]

28 REP AIR P AR TS SNOW THROWER - MODEL PP10530ES (96192001800) CHAS SIS / ENGINE / PULLEYS 6 19 17 10 21 22 23 2 3 4 6 9 12 15 27 26 25 24 18 7 20 30 29 31 31 58 10 21 28 57 6 53 1 7 8 13 14 47 40 46 44 49 50 51 52 35 34 33 38 37 39 43 11 32 32 36 36 44 45 41 11 11 31 07Chassis-chain-cord-T ec_3 5 5 5 16 56[...]

29 REP AIR P AR TS SNOW THROWER - MODEL PP10530ES (96192001800) CHAS SIS / ENGINE / PULLEYS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO[...]

30 REP AIR P AR TS SNOW THROWER - MODEL PP10530ES (96192001800) WHEELS / DECALS 7 32 30 32 30 15 18 17 19 13 20 11 27 27 19 16 20 11 11 11 11 14 15 12 13 18 14 12 4 4 31 34 34 2 8 3 21 33 22 23 24 25 26 28 28 29 10 10 4 4 7 28 28 26 29 25 24 23 22 33 21 9 1 2 3 10 5 3 1 4 2 1 10 6 9 11 12[...]

31 KEY P ART NO . NO. DESCRIPTION 1 192092X421 Wheel Assembly , 16", Power Steering, LH 2 155443 Pin, Klik 1/4 3 405161 Cover , Power Steering 4 184471 Screw , Hex Head #10-24 x 1/2 7 17060410 Capscrew , Hex Head, Flanged 3/8-16 x 1 8 410294 Bracket, Steering Cable, RH 9 410293 Bracket, Steering Cable, LH 10 17600406 Screw , Hex Head 1/4-20 x [...]

LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer pur - chaser , we will repair or replace, at our option, without charge for parts or labor incurred in repl[...]