Raymarine ST80 manual

Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company.[...]

ST80 Maxiview Operation & Setup[...]

Maxiview[...]

ST80 Maxiview Operation and Setup 1 Package Contents 1. Maxiview display head 2. Thumb nuts (2) 3. Threaded fixing studs (2) 4. White sun cover 5. SeaTalk cable 6. Installation template 7. Operation manual 8. Warranty card 9. Operation cue card 10. Display head installation guide[...]

ST80 Maxiview Operation and Setup 2 Contents Chapter 1: Introduction ............................................................. 7 Quick Reference Guide ............................................... 7 Chapter 2: Operation ............................................................... 10 2.1 General .............................................[...]

ST80 Maxiview Operation and Setup 3 2.6 Navigate Chapter ........................................................ 2 2 Position Page ............................................................. 2 2 Course Over Ground (COG) & Bearing to Waypoint (BTW) ...................................................................... 22 Cross Track Error ...[...]

ST80 Maxiview Operation and Setup 4 Chapter 3: Setup ...................................................................... 36 3.1 Entering Setup ............................................................ 36 Speed Chapter ........................................................... 3 7 Response Pages ...............................................[...]

ST80 Maxiview Operation and Setup 5 Chapter 4: CodeLock Security ................................................. 58 4.1 What is CodeLock? .................................................... 58 Master’s .................................................................... 58 Slave’s .............................................................[...]

ST80 Maxiview Operation and Setup 6[...]

ST80 Maxiview Operation and Setup 7 Chapter 1: Intr oduction D1580-1 maxiview SPEED KNOTS The Maxiview is a large-screen LCD repeater capable of displaying single or multiple lines of alphanumeric SeaTalk data. With a display area measuring 126 x 70mm (5 x 2.7in), the Maxiview provides a clear and unambiguous display wherever you are on your boat. [...]

ST80 Maxiview Operation and Setup 8 maxiview maxiview remote Press this key momentarily to cycle the available chapters. Press and hold for 1 second to select illumination adjustment. Additional key presses change the illumination setting. Press this key momentarily to cycle pages within the currently selected chapter. Press and hold for 1 second t[...]

ST80 Maxiview Operation and Setup 9 SPEED CHAPTER SPEED SPEED OVER GROUND VMG TO WIND LOG & TRIP CHAPTERS PAGES AVERAGE SPEED MAXIMUM SPEED NP NAVIGATE CHAPTER TIMERS CHAPTER RACE TIMER MULTILINE CHAPTER UP TO 8 USER DEFINED PAGES POSITION COG BTW CROSS TRACK ERROR VMG TO WAYPOINT WAYPOINT DATA DATE TIME TIDE WIND CHAPTER APPARENT WIND SPEED AP[...]

ST80 Maxiview Operation and Setup 10 Chapter 2: Operation 2.1 General The Maxiview operates around a chapter and page principle – chapters are independent sections: speed, depth, wind, etc., and pages data related to that chapter. When the Maxiview is powered up for the first time, the unit defaults to the SAIL configuration, unless a POWER confi[...]

ST80 Maxiview Operation and Setup 11 2.2 Speed Chapter Boat Speed Page This page displays your actual boat speed. D2469-1 maxiview remote SPEED KNOTS 10.5 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. • The speed units are the units currently on [...]

ST80 Maxiview Operation and Setup 12 Speed Over Ground (SOG) Page This page displays your current speed over the ground from GPS. D2470-1 maxiview remote SOG 6.5 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. KNOTS • The speed units can be: KNOTS,[...]

ST80 Maxiview Operation and Setup 13 Log/Trip Page The Log/Trip page displays the total distance logged and a list of trips and their current status. D2472-1 maxiview remote LOG/ TRIP LOG TRIP 1 OFF TRIP 2 OFF TRIP 3 ON TRIP 4 OFF TRIP 5 ON Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 [...]

ST80 Maxiview Operation and Setup 14 Average Speed This page displays the average boat speed for your current journey. D2473-1 maxiview remote SPEED AVG 8.0 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. KNOTS • The units are those currently on Se[...]

ST80 Maxiview Operation and Setup 15 2.3 Depth Chapter Depth Page The depth page displays the current depth available on SeaTalk. D2475-1 maxiview remote DEPTH FEET Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. 32.5 • The displayed units are thos[...]

ST80 Maxiview Operation and Setup 16 Minimum Depth Page D2476-1 maxiview remote DEPTH MIN 9.2 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. FT Press and hold these keys for 4 seconds to reset the minimum depth. • The units are: FEET, FATHOMS or M[...]

ST80 Maxiview Operation and Setup 17 2.4 Wind Chapter Apparent Wind Speed page D2478-1 maxiview remote WIND APP 20.0 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. KNOTS • The units can be : KNOTS or M/SEC. Apparent Wind Angle Page D2479-1 maxivie[...]

ST80 Maxiview Operation and Setup 18 True Wind Speed Page (Relative to the Vessel) D2480-1 maxiview remote 8.5 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. KNOTS • The true wind units can be either: KNOTS or M/S. • This page is not available i[...]

ST80 Maxiview Operation and Setup 19 True Wind Angle (Referenced to the Compass) D2482-1 maxiview remote 296 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. WNW M • This page is not available in POWER mode. • The angle can be either true (T) or m[...]

ST80 Maxiview Operation and Setup 20 Steering Page The steering page displays the current compass heading (unlocked mode) or the locked compass heading (locked mode). Note: For a detailed description of locked mode, please refer to a Masterview handbook. D2484-1 maxiview remote STEER 136 Press momentarily to advance to the next chapter. Press momen[...]

ST80 Maxiview Operation and Setup 21 Bearing to Waypoint (BTW) Page This page shows the magnetic or true bearing to a target waypoint. D2486-1 maxiview remote BTW 276 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. TRUE Tack Course Page This page dis[...]

ST80 Maxiview Operation and Setup 22 2.6 Navigate Chapter Position Page D2488-1 maxiview remote POSITION 050 49.10 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. N-E 002 49.10 • If position data is not available the fields are filled with dashes. [...]

ST80 Maxiview Operation and Setup 23 Cross Track Error The cross track error (XTE) page shows how far, in nautical miles (NM), statute miles (SM) or kilometres (KM), your vessel is from a planned route. D2490-1 maxiview remote XTE 0.34 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 secon[...]

ST80 Maxiview Operation and Setup 24 Waypoint Data Page This page displays any cross track error, the distance to a target waypoint (DTW), estimated time to arrival (ETA) and waypoint number. D2492-1 maxiview remote Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the p[...]

ST80 Maxiview Operation and Setup 25 Date/Time/Tide Page This page displays the speed and direction of the tide and the local time. D2493-1 maxiview remote Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. 12 JUNE 95 TIDE 6.5 KNOTS 130 TRUE • Local t[...]

ST80 Maxiview Operation and Setup 26 2.7 Race Timer Chapter Race Start Page This page duplicates race timer data from a Masterview instrument. There are just two operating modes: STOPPED and COUNTING DOWN/UP. D2494-1 maxiview remote RACE START 10:00 Press momentarily to advance to the next chapter. • The display shows minutes and seconds only. ?[...]

ST80 Maxiview Operation and Setup 27 2.8 Multi-Line Multi-line chapters consist of up to 8 pages of user-defined pages. D2496-1 maxiview remote DEPTH 7.2 Press momentarily to advance to the next chapter. Press momentarily to advance to the next page. Press for 1 second to return to the previous page. FEET Press these keys together momentarily to en[...]

ST80 Maxiview Operation and Setup 28 Multi-line Setup D2498-1 maxiview remote DEPTH 25.2 Press to change the current option to the previous option. Press to change the current option to next option. FEET Press and hold these keys for 4 seconds to delete the current multiline page. HEADING 120 M 2 SPEED 6.5 KTS Press and hold these keys for 4 second[...]

ST80 Maxiview Operation and Setup 29 List of Multi-line Selections The lines of data that can be selected are as follows: Line Data Line Data 1 Speed 17 Steer 2 Speed over ground 18 Course over ground 3 Velocity made good to wind 19 Tack course 4 Velocity made good over ground 20 Vessel latitude 5 Log 21 Vessel longitude 6 Trip 1 22 Cross track err[...]

ST80 Maxiview Operation and Setup 30 Multi-line Factory Defaults The factory defaults for the Multi-line pages are: Page Line Content 1 1 Speed 2 Average speed 3 Speed over ground 4 Velocity made good to waypoint 2 1 Depth 2 Water temperature 3 1 Heading 2 Steer 3 Course over ground 4 Bearing to waypoint 4 1 True wind angle 2 True wind speed 3 Tack[...]

ST80 Maxiview Operation and Setup 31 2.9 Illumination There are two modes: local and system. Each of these modes has four possible settings: level 3 (brightest), level 2, level 1 and off. Local illumination is used to adjust the lighting of individual display heads — adjustments will not affect other display heads. System illumination controls th[...]

ST80 Maxiview Operation and Setup 32 Resetting the Contrast The display contrast can, during local or system illumination adjustment, be reset to the factory default by pressing the page key for 1 second. 2.10 Data Lost If a chapter that is dependent on a given quantity, e.g., speed, wind, depth, and this data is lost for more than 8 seconds, a war[...]

ST80 Maxiview Operation and Setup 33 • The dead reckoned screen is displayed providing data is available. • Fields where data is not available appear as dashes. • The elapsed time is displayed in minutes and seconds. • The displayed bearing and range is to the man in the water. Lat/Lon MOB D2543-1 maxiview remote 08:30 Press this key moment[...]

ST80 Maxiview Operation and Setup 34 MOB Audible Alarm During an MOB condition, an audible alarm beeps 3 times every thirty seconds. Alarms The Maxiview can be set to respond to all the alarms in the following table or, alternatively, only those identified as specific. Alarm Pop-Up Displayed Response Shallow depth SHALLOW WATER All Deep depth DEEP [...]

ST80 Maxiview Operation and Setup 35 The following table lists the alarm status once a silence/turn off key- sequence is performed. Alarm Silenced Turned Off Shallow depth Yes No Deep depth No Yes Anchor Yes N o True wind high speed No Yes True wind low speed No Yes True wind high angle No Yes True wind low angle No Yes Apparent wind high speed No [...]

36 ST80 Maxiview Operation & Setup Chapter 3: Setup This chapter describes how to set and adjust features in the setup menu. These include display formats, response levels for controlling the frequency of screen updates and the thresholds for trend indicators. 3.1 Entering Setup D2499-1 maxiview remote DEPTH f FEET Press and hold these keys tog[...]

ST80 Maxiview Operation & Setup 37 Speed Chapter The following screen is displayed for 2 seconds when entering speed setup. The key sequences shown are only available during this period. D2500-1 maxiview remote CHAP 1S FOR INSTRUMENT CHAPTER SPEED Press this key to advance to the next chapter. SET-UP Press this key for 1 second to return to the[...]

38 ST80 Maxiview Operation & Setup There are two response pages: speed and VMG to wind. Speed response covers boat speed, speed over ground, velocity made good to waypoint and velocity made good over ground to waypoint. D2501-1 maxiview remote Press this key momentarily to advance to the next chapter. SPEED KNOTS 16.5 RESPONSE S F 07 Press this[...]

ST80 Maxiview Operation & Setup 39 D2502-1 maxiview remote Press this key momentarily to advance to the next chapter. 0.80 KNOTS/ SEC Press this key momentarily to advance to the next page. Press this key for 1 second to return to the previous page. Press these keys together momentarily to decrease value by 0.01. Press these keys together momen[...]

40 ST80 Maxiview Operation & Setup Display Format The display format can be set to either 1 or 2 decimal places. D2503-1 maxiview remote Press this key momentarily to advance to the next chapter. X.X X.XX Press this key momentarily to advance to the next page. Press this key for 1 second to return to the previous page. Press these keys together[...]

ST80 Maxiview Operation & Setup 41 Depth Response D2505-1 maxiview remote Press this key momentarily to advance to the next chapter. DEPTH FEET 20.5 RESPONSE S F 07 Press this key momentarily to advance to the next page. Press this key for 1 second to return to the previous page. Press these keys together momentarily to decrease value by 1. Pre[...]

42 ST80 Maxiview Operation & Setup Depth Display Format D2507-1 maxiview remote Press this key momentarily to advance to the next chapter. X X.X Press this key momentarily to advance to the next page. Press this key for 1 second to return to the previous page. Press these keys together momentarily to highlight X format. Press these keys togethe[...]

ST80 Maxiview Operation & Setup 43 Wind Speed Response D2509-1 maxiview remote Press this key momentarily to advance to the next chapter. WIND SPEED KNOTS 5.0 RESPONSE S F 07 Press this key momentarily to advance to the next page. Press this key for 1 second to return to the previous page. Press these keys together momentarily to decrease value[...]

44 ST80 Maxiview Operation & Setup Display Format D2507-1 maxiview remote Press this key momentarily to advance to the next chapter. X X.X Press this key momentarily to advance to the next page. Press this key for 1 second to return to the previous page. Press these keys together momentarily to highlight X format. Press these keys together mome[...]

ST80 Maxiview Operation & Setup 45 Editing Rights The editing rights chapter allows you to control the level of multiline page editing. The options are: edit all, edit pages and no editing. D2513-1 maxiview remote Press this key momentarily to advance to the next chapter. EDIT ALL EDIT PAGES NO EDITING Press this key momentarily to advance to t[...]

46 ST80 Maxiview Operation & Setup 3.2 Instrument Setup D2514-1 maxiview remote CHAP 1S FOR MULTILINE CHAPTER INSTRUMENT Press this key to advance to the next chapter. SET-UP Press this key for 1 second to return to the multiline chapter. Transducers Page This page lists all the transducers connected to SeaTalk. D2515-1 maxiview remote Press th[...]

ST80 Maxiview Operation & Setup 47 Sail/Power/Custom Selection This page allows you to select whether chapters are custom selections or, alternatively, dictated by the sail or power boat settings. D2516-1 maxiview remote Press this key momentarily to advance to the next chapter. Press this key momentarily to: go to the custom setup page if CUST[...]

48 ST80 Maxiview Operation & Setup Custom This mode allows you to select any of the chapters from the following list: No. Chapter No. Chapter 1 Speed 5 Navigate 2 Depth 6 Timers 3 Wind 7 Multiline 4 Heading D2517-1 maxiview remote Press this key momentarily to return to speed calibration chapter. Press this key momentarily to advance to the Tit[...]

ST80 Maxiview Operation & Setup 49 Contents Setup In custom setup, contents setup is used to select or de-select pages within the highlighted chapter. D2518-1 maxiview remote Press this key momentarily to return to the chapter setup page. Press these keys together momentarily to highlight the next page. Press these keys together momentarily to [...]

50 ST80 Maxiview Operation & Setup Title Control This is used to turn the chapter title pages, displayed for 2 seconds upon entry to a chapter, ON or OFF. D2519-1 maxiview remote Press this key momentarily to return to speed calibration chapter. Press this key for 1 second to return to the sail/power/custom selection page. Press this key moment[...]

ST80 Maxiview Operation & Setup 51 Variation This page is used to enter the local variation to the nearest whole degree. D2520-1 maxiview remote Press this key momentarily to return to speed calibration chapter. Press this key for 1 second to return to the title control page. Press this key momentarily to advance to the true/magnetic heading se[...]

52 ST80 Maxiview Operation & Setup True/Magnetic Heading The true/magnetic heading page is used to select one of four options: local true, local magnetic, global true or global magnetic. D2531-1 maxiview remote Press this key momentarily to return to speed calibration chapter. Press this key for 1 second to return to the variation page. Press t[...]

ST80 Maxiview Operation & Setup 53 Lamp Offset Adjustment This feature allows you to adjust the brightness of individual illumination levels to obtain the best setting for a particular location. D2532-1 maxiview remote LAMP ADJSUTMENT LEVEL 2 MIN MAX 32 Press this key momentarily to advance to contrast adjustment. Press this key for 1 second to[...]

54 ST80 Maxiview Operation & Setup Contrast Adjustment D2533-1 maxiview remote CONTRAST ADJUSTMENT MIN MAX 07 Press this key momentarily to advance to LCD inversion control page. Press this key for 1 second to return to the previous page. Press these keys together momentarily to decrease value by 1. Press these keys together momentarily to incr[...]

ST80 Maxiview Operation & Setup 55 LCD Inversion LCD inversion allows you to change the display to: • display black numbers and characters on a light background • or display light numbers and characters on a black background D2534-1 maxiview remote Press this key momentarily to return to speed setup. Press this key for 1 second to return to[...]

56 ST80 Maxiview Operation & Setup Alarm Control This page is used to define whether all or just specific alarms will be recognised by the Maxiview. D2535-1 maxiview remote Press this key momentarily to return to speed setup. Press this key for 1 second to return to LCD inversion. Press this key momentarily to return to transducers page. Press [...]

ST80 Maxiview Operation & Setup 57 3.3 Quitting User Setup To quit setup, simply press the Chapter and Page keys together momentarily to display the following screen. D2539-1 maxiview remote EXIT If cancel is selected, press this key momentarily to exit without saving. If store is selected, press this key momentarily to exit and store new setti[...]

58 ST80 Maxiview Operation & Setup Chapter 4: CodeLock Security 4.1 What is CodeLock? • CodeLock is a personal four digit security code designed to protect your valuable equipment against theft. • CodeLock does not have to be switched on, but it’s there if you decide that you need it. • When CodeLock is switched on, the code number is s[...]

ST80 Maxiview Operation & Setup 59 4.2 Analogue Display Heads Automatic CodeLock Systems In an automatically transmitted CodeLock system, the Maxiview reads the code number and starts-up automatically without any user input. Manual CodeLock System In a manually transmitted CodeLock system, the code number is entered via the keypad of any master[...]

60 ST80 Maxiview Operation & Setup Chapter 5: Pr oblem Solving 5.1 Problem Solving Display is blank • Make sure that the power supply is connected. • Check the fuse or circuit breaker. • Make sure that the SeaTalk cables are not damaged. • Check the contrast and illumination settings • Faulty LCD module. No exchange of information bet[...]

ST80 Maxiview Operation & Setup 61 Chapter 6: EMC and Servicing Guidelines 6.1 Important information All Autohelm equipment and accessories are designed to the best industry standards for use in the leisure marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but good instal[...]

62 ST80 Maxiview Operation & Setup 6.3 Check Before Going to Sea • Always check the installation before going to sea to make sure that it is not affected by radio transmissions, engine starting etc. • In some installations, it may not be possible to prevent the equipment from being affected by external influences. In general this will not d[...]

ST80 Maxiview Operation & Setup 63 Chapter 7: Specification Dimensions: 110 x 114.5 x 18.25mm (4.33 x 4.5 x 0.71in) Power supply: 10 to 16 V DC Current consumption: 50 mA with illumination off 250mA with illumination full on Operating temperature: -10 to +70°C (14°F to 158°F) Illumination: 3 level illuminated dial and LCD keypad permanently [...]

64 ST80 Maxiview Operation & Setup[...]

ST80 Maxiview Operation & Setup 65 Index A Alarm Control 56 Alarms 34 Apparent Wind Angle Page 17 Apparent Wind Speed page 17 Audible Alarms 35 Automatic CodeLock Systems 59 Average Speed 14 B Bearing to Waypoint (BTW) Page 21 Boat Speed Page 11 C CodeLock Security 58 Contents Setup 49 Contrast Adjustment 54 Course Over Ground (COG) & Beari[...]

66 ST80 Maxiview Operation & Setup 81022–1 O Operating the Maxiview using the Remote Keypad 10 P Problem Solving 60 Q Quitting User Setup 57 R Race Start Page 26 Race Timer Chapter 26 Resetting the Contrast 32 Response Pages 37 S Sail/Power/Custom Selection 47 Servicing and Safety 62 Setup 36 Setup and Calibration 7, 36 Specification 63 Speed[...]

Maxiview[...]

Raymarine Ltd. Anchorage Park, Portsmouth, P03 5TD, England. T elephone : (44) (0) 2392 693611 Fax: (44) (0) 2392 694642[...]