ResMed Comfort manual

SULLIV AN ® Comfort  Bi-level System Operating Manual[...]

Please read and understand this manual before using the system. Record of information for future reference Complete the following details when you receive your SULLIVAN ® Comfort. Unit prescribed by (physician) _______________________________ Sleep clinic _______________________________ Date prescribed _______________________________ Prescribed pr[...]

 Contents 3 Content s 1 Introduction ...................................................................................................... 4 How [...]

SULLIVAN Comfort Operating Manual  4 1 Introduction How bi-level treatment works Obstructive sleep apnea or OSA occurs when the tongue and soft palate relax during sleep, blocking the airway and cutting off the b[...]

Section 1: Introduction 5 Features of SULLIV A N ® Comfort Delay timer If you find the initial sensation of pressure uncomfortable while trying to fall asleep you may use the delay timer. This allows you to select the time it will take (5, 10 or 20 minutes) for the air pressure in your mask to build up gradually to your prescribed pressures. Yo[...]

SULLIVAN Comfort Operating Manual  6 SULLIVAN Comfort bi-level system 2 Component s of SULLIV A N ® Comfort You should take time to become familiar with the components of your SULLIVAN ® Comfort bi-level sys[...]

Section 3: Preparing for use 7 Prep aring for use Assembling the mask system The mask frame has two access ports which should be plugged and are not used except for initial pressure setting by a technican. It has a swivelling mask elbow which allows the air tubing to be positioned without kinks. The air outlet vent allows exhaled air to escape quie[...]

SULLIVAN Comfort Operating Manual  8 4 Fit the headgear to the mask frame as shown below. • Thread the headgear straps through the slots in the mask frame – the lower straps should also pass through the slots[...]

Section 3: Preparing for use 9 2 Switch the main switch at the rear of the flow generator on ( I ). Press the START button on the front panel (see figure below). Allow the unit to run for a few seconds, then press the STOP button. STOP button Front panel 3 Positioning the flow generator • Place the flow generator on a table close to the head of y[...]

SULLIVAN Comfort Operating Manual  10 Connect the air tubing to the flow generator and mask IMPORTANT:  Make sure the power cord and plug are in good condition and the equipment is not damaged.  Only use th[...]

Section 4: Fitting the mask 11 Fitting the mask The mask frame and headgear should be assembled as described in section 3, Preparing for use . To fit the mask to your face: 1 Loosen the headgear straps and pull the headgear over your head. Make sure the straps are sufficiently loose so that the nasal cushion is not pulled against your nose. 2 Posit[...]

SULLIVAN Comfort Operating Manual  12 5 Adjust the air tubing – try both ways and select whichever is more comfortable Using the START button Start the flow generator by pressing the START button. The pressure [...]

Section 5: Daily operation 13 * The pressure strip light display gives an approximate indication of the pressure you are receiving. You will notice that the indicator lights fluctuate as the unit switches between your IPAP and EPAP pressures. Using the delay timer If you prefer to have the air pressure build up gradually while you fall asleep, sele[...]

SULLIVAN Comfort Operating Manual  14 S topping 1 Press the STOP button to stop the flow generator. To remove the mask, stretch the headgear slightly and pull it over your head. Or release one of the bottom headg[...]

Section 6: Helpful hints 15 Help ful hint s • When you use your SULLIVAN ® Comfort™ bi-level system for the first time you may notice an unusual sense of pressure when breathing. Even though a reduced pressure is delivered when you breathe out, you may still need to consciously push out when breathing out. This is normal and will occur automat[...]

SULLIVAN Comfort Operating Manual  16 Use in different countries • Your SULLIVAN ® Comfort™ has a switch mode power supply which means it will operate on the different power supplies in other countries. The [...]

Section 8: Warnings related to treatment 17 W arnings related to treatment The SULLIVAN ® Comfort™ bi-level system is designed to help you have a good night’s sleep. However, you need to be aware of possible problems that may arise during the course of your treatment. If you have concerns about any of these problems consult your physician imme[...]

SULLIVAN Comfort Operating Manual  18 9 Cleaning and maintenance You should regularly carry out the cleaning and maintenance described in this section. These procedures do not require a specialist service organiz[...]

Section 9: Cleaning and maintenance 19 Remove air filter box at rear of flow generator Periodically All items of the mask and air tubing system are subject to normal wear and tear and may eventually need to be replaced. Check periodically for excessive wear in these items. 1 When dirty, remove the headgear and wash it in warm water using a mild det[...]

SULLIVAN Comfort Operating Manual  20  Do not wash the filter strips as they will be damaged and will not function effectively.  Do not attempt to open the flow generator unit. Repairs and internal servicin[...]

Section 10: Servicing 21 10 Servicing Your SULLIVAN ® Comfort™ is designed to give years of trouble-free operation. It is not necessary to send your unit away for regular servicing provided you follow the recommendations in section 9, Cleaning and maintenance . Should you feel that your unit is not performing properly, check section 11, Troubles[...]

SULLIVAN Comfort Operating Manual  22 T roubleshooting If you have any problems with your SULLIVAN ® Comfort™, try the following suggestions. If it is still not working properly, consult your equipment supplie[...]

Section 12: Accessories and spare parts 23 Accessories and sp are p art s Accessories A range of accessories is available to adapt your SULLIVAN ® Comfort™ to your needs. Contact your sleep clinic or equipment supplier for further information on the following items. Modular Mask Frame Kit Adapts to a wide range of face sizes and features a T-bar[...]

SULLIVAN Comfort Operating Manual  24 SULLIVAN ® HCH Disk – a foam insert which fits inside your mask frame HC100 Heated Humidifier Passover Humidifier Humidifiers Bi-level treatment sometimes results in a dry[...]

Section 13: System specifications 25 13 System specifications SULLIV A N ® Comfort bi-level system Flow generator unit PERFORMANCE Operating pressure range: 4-18 cm H 2 O Maximum IPAP time range: 0.2-10.8 seconds DIMENSIONS (H x W x D) 145 x 240 x 350 mm (5.7 x 9.5 x 13.8 in) WEIGHT 4.1 kg (9.1 lb) POWER SUPPLY Input range 110-240 V, 50-60 Hz, [...]

21802/3 00 08 • ResMed Malaysia Sdn Bhd Unit 4.04, Wisma BICMA Jalan 243/51A 46100 Petaling Jaya Selangor Malaysia Tel: +60 3 7877 9099 Fax: +60 3 7877 6099 Email: reception@resmed.com.my • ResMed NZ Ltd PO Box 51-048 Pakuranga Auckland New Zealand Tel: +64 9530 9049 or +0800 737 633 (NZ toll free) Fax: +64 95309048 Email: reception@resmed.com.[...]