Ricoh FV-G030B1 manual

1/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 GigE Vision VGA Monochrome CCD Camera FV-G030B1 User ’s Guide RICOH CO MP AN Y , L TD.[...]

2/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 T able of Content s 1 Connect or S pecificatio ns ..... ..... .......... ........ ..... ..... ..... ......... ..... ..... ..... ......... ... ..... ..... ..... ......... ..... ..... ..... ......... ... ...3 1.1 RJ45 Connector ..................................... ........................................[...]

3/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 1 Connector Specifications 1.1 RJ45 Conn ector This product is NOT a PoE t ype. A ppl y power (+10. 8 to +26.4Vdc) ONL Y through the I/O connector . Pin Assignment: LED Inform ation: Pin No. Signal Name 1 T A+ 2 T A- 3 TB+ 4 TC+ 5 TC- 6 TB- 7 TD+ 8 TD- Please use a 1Gb supported NIC, HUB and LAN cab le.[...]

4/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 1.2 DC Iris Len s Conne ctor  M1951 (EMUDEN) or e quivalent. Pin Assignment Pin No. Signal Name 1 DAMP- 2 DAMP+ 3 DRIVE+ 4 DRIVE- 1.3 Power-I/O Connector  HR10A-7R-6PB （ Hirose ） or equivalent  This connector is f or the power supp ly (12Vdc) and i nput /output sig nals.  Use HR10A-7P-6S[...]

5/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Note: I/O-1 can be ass igned only b y F0H[3..0] and F1[ 3], and I/O-2 can b e assigned o nly by F0H[7..4] a nd F1[4]. 1) F rameTrigg erWait The user can check the camer a conditi on (camera exposure and image output processing by t he trigger signal with this FrameTrigger Wait signal). This signal is LO[...]

6/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 1.3.1 Equivalent Circuit for the Input Pin of t h e I/O Connector +3.3V +3.3V +3.3V TOSHIBA RN1105MFV TOSHIBA RN1105MFV 2 1 3 TOSHIBA TLP181 TOSHIBA TLP181 3 4 6 1 2.2K 2.2K 1 2 3 4 5 6 TOSHIBA RN1105MFV TOSHIBA RN1105MFV 2 1 3 1K 1K 1K 1K +10.8 to +26.4V Trigger_In+ Trigger_In- IO_Out IO_Out GND Custom[...]

7/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 2 Camera Output T im ing Chart s 2.1 Horizont al Ti ming 1 CLK = 27.1605 nseco nds 2.2 V ertical T iming 2.2.1 Full Scannin g 1 H = 21.1852 µsecon ds, 89.91 172 Hz 132 CLK 648 CLK Video out LVAL DVAL Horizontal b lanking 780 CLK One horizontal (1H) 648 CLK 132 CLK 132 CLK Video out put 132 CLK 94 CLK 3[...]

8/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 2.2.2 1/2 Partial S canning 1 H = 21.1852 μ s, 180.16662 Hz 2.2.3 1/4 Partial S canning 1 H = 21.1852 μ s, 360.33325 Hz 243H Video out Vertical blanking 262H One vertical (1V) 19H 19H Video output 368 369 127 128 FVAL 243H 19H 19H LVAL DVAL 104H Video out Vertical blanking 1 3 1 H One vertical (1V) 10[...]

9/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 2.2.4 AOI (Area o f Interest) Internal HD Internal VD Video out EXT_T RIG FIX_TR IG (Com mon) 10 20 30 40 50 Exposure time V1 V2 V3 SUB FVAL LVAL Number of the effective l ines [Y] High spee d transfer ［ X+a ］ High spee d transfer ［ f+g-X-Y ］ Blanki ng (Fron t) [BLK_F] Number of the effecti ve l[...]

10/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 2.3 Pixel T ransferring I mage Pixel (n) of Data: nth pixel b eing transfer red Pixel1 of Data Pixel2 of Data[...]

1 1/3 8 FV -G030B 1 User ’s Gu i de Rev . 1.02 3 Camera Operational Modes 3.1 Normal Mod e 3.2 Pulse W idth Tr igger Mode In this tri gger mode with positive polarity , the cam era exposure start s at the rising edge of the trigger p ulse and stops at the f alling edge of the tr igger p ulse. Theref ore, if positive polar ity expos ure is s elect[...]

12/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 3.2.2 Exposure T iming with the Pos i tive Polar i ty T rigger Signa l Note 1: T he trigger si gnal will be removed by the filter ing if the pulse width of the input trigger s ignal is less than 30 C LK. Please input a trigger signal with m ore than 31 CLK pulse width. Note 2: The exposure will s tart [...]

13/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 3.3 Edge Pres et Trigger Mode In this “edge preset tr igger m ode”, the cam era exposure starts at the ris ing edge of the trigger signal l ike the “pulse width trigger m ode” in the previous s ections. Howe ver, in this m ode, the exposure duration tim e is based on the preset value stored b y[...]

14/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 3.3.2 Exposure T iming with the Pos i tive Polar i ty T rigger Signa l Note 1: T he trigger si gnal will be removed by the filter ing if the pulse width of the input trigger s ignal is less than 30 C LK. Please input a trigger signal with m ore than 31 CLK pulse width. Note 2: The exposure will s tart [...]

15/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 3.4 Edge Pres et Trigger Mode (Tr igger Input W hile the Image Is Out) In this trigger m ode, the cam era exposure starts at the rising edge of th e trigger pulse. If trigger signal input is required w hile the image is out, then it is nec essary to disable the trigger sign al mask with the comm unicat[...]

16/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 3.4.2 Exposure T iming with the Pos i tive Polar i ty T rigger Signa l Note 1: T he trigger si gnal will be removed by the filter ing if the pulse width of the input trigger s ignal is less than 30 C LK. Please input a trigger signal with m ore than 31 CLK pulse width. Note 2: The exposure will s tart [...]

17/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 3.5 H Reset Mod e In this m ode, the exposure can be start during t he video is out f rom the camera without the horizontal noises. Therefor e, generates the SUB pulse t o sweep the char ges during the horizontal blank ing to prevent fr om getting horizontal noises. The image is getting the horizontal [...]

18/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 4 Communication Protocol This camera has a comm unication function th at enables external devises, s uch as a PC, to c ontrol the c am era’s functions. Please use the “R-GigE-Software” comm unication software, o r the following comm unication protocol to comm unicate to the cam era: 4.1 Commun ic[...]

19/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 The description of the format is as fol lows. Name Descriptions SOF S t art of Fram e. Always set or rec eive the value as “ 02H” Device Code This indicates the dest ination of com m unication. Set “000000” when accessing the cam era’s function settings Set “100000” when accessing the cam[...]

20/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 【 Example Code 】 Reading the data from the com m and 00H  Comm and to send: 02H, 00H, 00H, 01 H, 00H, 03H SOF Device Code Read/Write Page Selection Command Code Data Length Data EOF (8bit) (6 bit) (1bit) (1bit) (8bit) (8bit) (1byte) (8bit) 02H 00H 00H 01H 00H 03H  Comm and to receive upon a s[...]

21/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 4.4 Camera C ontrol Co mmand  The data unit of the each com mand is 1 byte (8bit).  The data c an be save d to the E EPROM if th ere is a n “X” i n t he “Save to E EPROM” column in the following list.  The camer a initializes based on the st ored data in the EEPROM when the power is ap[...]

22/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Device Code = 000 000 Command No. R/W Sav e to EEPROM Function Initial Dat a Data Range 58H R/W x frame rat e (Hz ) (Integer) (16 bit: D[7..0]) 59H R/W x frame rat e (Hz ) (Integer) (16 bit: D[15..8]) 5AH R/W x frame rate (Hz) (Decimal) (24bit: D[7..0]) 5BH R/W x frame rate (Hz) (Decimal) (24bit: D[15.[...]

23/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 4.4.2 Camera C ommand Li st (Device Code: 100000) Device Code = 100 000 Command No. R/W Save to EEPROM Function Initial Data Data Range 00 to 1FH reserved - - 20H R/W x e xposure mode (8bit: D[7..0]) 00H 21H R/W x AGC maximum li mit (8bit: D[7..0]) 255 0 to 2 55 22H reserved - - 23H R/W x u pper limit [...]

24/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Device Code = 100 000 Command No. R/W Save to EEPROM Function Initial Data Data Range 54H R/W x X_offset for AOI (8bit: D[7..0]) 55H R/W x X_offset for AOI (16bit: D[15..8]) 0 56H R/W x width for AOI (8bit: D[7..0]) 57H R/W x width for AOI (16bit: D[15..8]) 648 8 <= X <= 648, where X = offset + w[...]

25/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 4.4.3 Description s of the C amera Contro l Commands ( Device code: 000000) ; (The underline setti ngs are the f actory default s ettings) Command No. Command Description 10H: MOD1[7..0] [camera function mode 1] Initial data: MO D1[7..0] = 89H Sets the camera function mode. D[7..0] D7 D6 D5 D4 D3 D2 D1[...]

26/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Command No. Command Description 13H: MOD4[7..0] [Camera function mode 4] Initial data: MOD 4[7..0] = 60H Sets the camera function mode. D[7..0] D7 D6 D5 D4 D3 D2 D1 D0 D7: No Function Always set as “0” D6: T rigger s ignal mask during exposure 0: OFF (No mask) 1 : ON (Mask) D5 T rig ger signal mask[...]

27/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Command No. Command Description 19H FORMA T [7..0] [Image output format] initial data: FORM A T[7..0] = 0 1H Sets the output format of the image dat a. D[7..0] D7 D6 D5 D4 D3 D2 D1 D0 D7 to D3: No Function Always set as “00000” D2 to D0: Output format 000 : Mono8 (Monochrome) / BayerRGB8 (Color) 00[...]

28/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Command No. Command Description 3EH: WHITE_CLIP[15..8] 3FH: WHITE_CLIP[7..0] [White clip level for the white clip test pattern] Initial data: W HITE _CLIP[15..0] = 4,095; data range: 0 to 4,095 Sets the white clip level of the w h ite clip test pattern. 50H: DELA Y_I[7..0] 51H: DELA Y_I[15..8] 52H: DEL[...]

29/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Command No. Command Description 5EH: CDS_BASEGAIN[7..0] 5FH: CDS_BASEGAIN[15..8] [CDS Base Gain] Initial data: C DS_BASEGAIN[15..0] = 304, data range: 0 to 1023 W hen the resu lt of the below equation exceeds 1023, 1023 will be set CDS_BASEGAIN[15..0] + PGA[7..0] x 2 + GOFS[7..0] *PGA[7.0]: The CDS gai[...]

30/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Command No. Command Description 90H: STROBEON_I[7..0] 91H: STROBEON_I[15..8] 92H: STROBEON_I[23..16] 93H: STROBEON_F[7..0] [Active time (us) for the strobe signal] Initial data: STROBEON _I[23..0] =10, STRO BEDELA Y _ F[7..0] = 0, data range: 0 to 2,000,000 Active time for the strobe signal = (STROBEON[...]

31/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 4.4.4 Description s of the C amera Co mmands (Device cod e: 100000); (The underline setti ngs are the f actory default s ettings) Command No. Command Description 20H: [7..0] [Exposure mode] Initial data: 00H Sets the exposure mode, which is the AGC, the shutter mode and the iris lens control meth od. D[...]

32/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Command No. Command Description 2BH: [7..0] [Weight3 for ALC] Initial data: 1AH Sets the weight for ALC weight area 5 and 6. D[7..0] D7 D6 D5 D4 D3 D2 D1 D0 D7 to D4: Weight for ALC weight area 6 1 Range: 0 to 15 D3 to D0: Weight for ALC weight area 5 10 Range: 0 to 15 *Please set the ALC weight area w[...]

33/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Command No. Command Description 30H: [7..0] 31H: [15..8] [V ertical_1 position for the ALC weight area] Initial data: 32, data range: 0 to 493 Sets the vertical 1 position for the ALC weight area. 32H: [7..0] 33H: [15..8] [V ertical_2 position for the ALC weight area] Initial data: 169, data range: 0 t[...]

34/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Command No. Command Description 50H: [7..0] 51H: [15..8] [Y_offset for AOI] Initial data: 0, data r ange: 2 ≤ “Y_offset + Height” ≤ 494 Sets the Y _offset (the vertical st art position of the image for the AOI) 52H: [7..0] 53H: [15..8] [Height for AOI] Initial data: 494, data range: 2 ≤ “Y_[...]

35/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 4.5 GenICam Comman d / Camer a Command Ref erence T able Camera command GenICam command Device Command Function W id th 100000 5 6-57H W idth for AOI (pixel) Height 100000 52-53H Height for AOI (p ixel) PixelForm at 000000 12H.6-7 Video out (bit) OffsetX 100000 54-55H X off set for AOI (pixel) OffsetY [...]

36/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Camera command GenICam command Device Command Function GainAuto 100000 20H.3 AGC GainRaw 000000 30H CDS gain SmearHalfReducti on 0 00000 1 1H.4 S mear half r eduction GammaMode 10 0000 60H.0 Gamma table ON/OF F ReloadGamm aData 100000 60H.7 Gamma table ON/OFF LensManualAdjustm ent 100000 92H.0-1 Iris l[...]

37/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Caution: W id th, Height and PixelFor mat all affect the im age data size. Please use comm and name def ined b y G enICam when c hanging these values, as exampled in the following sam ple code. In the case to chan ge the W idth BOOL S et W idth ( PvDevice *pDev ice, PvInt64 lV alue ) { PvGenInteger* lG[...]

38/38 FV -G030B 1 User ’s Gu i de Rev . 1.02 Revision Histor y Rev Date Changes Note 1.00 2012/06/19  Initial Release 1.01 2012/07/06  Updated Document title Camer a Command List (Device Code: 00 0000) 10-13H, 3E-3F , 58-5CH, Camera Com mand List (Device Code: 1 00000) 20H, 21H, 22H, 23-2 8H Deleted 90H Deleted description ab out white bala[...]