RoyalTek GPS SPEED CAMERA WARNING DEVICE RCD-1000 manual

E n g l i s h 1 RoyalT ek GPS Speed Camera W arning Device RCD-1000 Offline version Users Manual[...]

E n g l i s h 2 Content 1.Product Introduction ......................................................................................................... ................ 3 1.1 Overview ................................................................................................................................ 3 1.2 Check the Package Content.....[...]

E n g l i s h 3 1 1 . . P P r r o o d d u u c c t t I I n n t t r r o o d d u u c c t t i i o o n n 1.1 Overview The Device is equipped with the latest generation SiRF St ar III digital processor specially designed for fast and accurate fix on GPS signals. It had been designed to help you drive safety within the confines of today’s speed limits, [...]

E n g l i s h 4 1.3 Install RCD-1000 in your vehicle z Place the Dashboard Pad on your dashboar d as close to the windscreen as possible i n clear view of the driver ’s line of sight. z Place your RCD-1000 device on the dashb o ard pad, which is designed to hol d it firmly in place. z Now connect the USB cable to the cigar lighter adapter pr ovid[...]

E n g l i s h 5 2 2 . . S S p p e e c c i i f f i i c c a a t t i i o o n n 2.1 Specification GPS GPS Chip set - Sirf GSC3f/LP Frequency - L1, 1,575.42 MHz Channel - 20 parallel C/A Code - 1,023 MHz Chip set TTFF (Open SKY ,typical) - Reacquisition: less than 1s - Hot start: less than 1s - W arm st art: less than 35s - Cold start: less than 35 s Ac[...]

E n g l i s h 6 2.2 Hardware Overview (1) The POI record Button : Press for more than 2 seconds to record current position. A short beep soun d and blinking LED will inform yo u that the POI has been successfully store. Note: The user must use the software to carry out the POI management. Note: The POI Record Button fun ction will be enabled af ter[...]

E n g l i s h 7 *Depending on local SCDB conditions. Event LED Display Audio A larm 1 System Initialize Green+Red (No 1+No 2+No3), S weeping 1 beep 2 GPS Search Green (No 1), Blinking 3 GPS is fixed Green (No 1), Glowing 2 beeps after GPS Fixed 4 Memory full /Erase Not available for this model X Not exceed speed Glowing 3 beeps 5 Approach Fix Camer[...]

E n g l i s h 8 3 3 . . S S o o f f t t w w a a r r e e I I n n s s t t a a l l l l a a t t i i o o n n a a n n d d U U s s a a g g e e 3.1 Start to use “Speed Camera Detector Utility ” Check the COM port of RCD-1000 first. Click “Start” Æ “Control Panel” Æ ”Performance and Maintenance” Æ “System”, and you will see the System[...]

E n g l i s h 9 Figure2 Figure3 Figure 4 is shown System will download the POI point s from device automatically . POI dat a will be erased from device af ter POI load process done. Figure 4 If the figure 5 dialog is shown, it means there is no POI dat a in the device.[...]

E n g l i s h 10 Figure 5 3.2 POI Management Procedure When proceed the POI Management, system will auto create the POI folder for POI data download. Note: POI data are stored in the PC side and named POI.csv and stored in the subdirectory /POI/. User can load POI data, delete POI dat a or Save POI data by using the Utility . Note: ◆ Load POI: Us[...]

E n g l i s h 11 please refer to Figure 6. Figure 6 Figure 7 shows the Load POI process done. Figure 7 Figure 8 shows the Delete POIs process.[...]

E n g l i s h 12 Figure 8 3.2.1 POI Management and shown on Map T o display the POIs on Google Map, the Internet connection is needed. Move the mouse cursor to the required “Latitude” or “Longitude“ point column then press the mouse right key , the message “Go to Google Map” showed as Figure 9 Figure 9 3.2.2 POI data modification User c[...]

E n g l i s h 13 After the modification is complete, please press t he button “OK” to save the modification. ◆ Go to SCDB Coverage: Show the device’s speed camera database coverage on Google Map ◆ Go to POI: When user clicks the “Go to POI” button, the screen will back to the POI point Map window . (Example) 2) Modification of the com[...]

E n g l i s h 14 Figure 8 3.3 SCDB and POI import setting ◆ SCDB Setting : There is one type Camera database dat a. Fixed S peed Camera database dat a User can download the S peed Camera database from his computer (local file). For the S peed camera database file format, please reference the example: File name: *.csv Latitude, Longitu de, directi[...]

E n g l i s h 15 Figure 1 1 3.3.1 Download SCDB data from Local file Currently , users can upload DB data combinations are as follows: 1) Only SCDB 2) SCDB + POI 3.3.1.1 Download SCDB data from Local file If user wants to downlo ad SCDB data from user computer (local file), please che ck the” Download S peed Cameras from Local file.” And select[...]

E n g l i s h 16 Figure12 Press the button “Go to Connection Page” and the AP will go to the “connection” p age. System will show the notification message. Shows as Figure 13 and 14 Figure13 Figure14 Figure 15 shows that the upload proceed.[...]

E n g l i s h 17 Figure15 Figure 16 shows that the download process is completed. And system will auto alert you to do the action ”RESRT a nd Reconnect the device” after the upload process was co mpleted. Please re-connect the device. Figure16 3.3.2 POI Setting process Go to the page “SCDB and POI import setting”, user should check the chec[...]

E n g l i s h 18 3.4 SCDB Setting Change to “SCDB Setting” menu bar ◆ Speed Camera Alert Setting : User can set the Critical Range value and Notification range of the device. Note: Notification range should be bigger than Critical range 200m. Figure17 3.5 Utility Revision information Change to “About” menu bar User can get the RoyalT ek S[...]