Ryobi HP1802M manual

THANK YOU FOR BUYING A R YOBI CORDLESS DRILL-DRIVER. Y our new cordless drill-driver has been engineered and manufactured to Ryobi’ s high standard for dependability , ease of operation, and operator safety . Properly cared for , it will give you years of rugged, trouble-free performance. CAUTION: Carefully read through this entire operator’s m[...]

Page 2 ■ General Safety Rule ............................................................................................................ .................................... 2-3 ■ Specific Safety Rules/Symbols .................................................................................................. .............................. 3-5 ?[...]

Page 3 T ool Use and Care ■ Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. ■ Do not force tool. Use the correct tool for your appli- cation. The correct tool will do the job better and safer at the rate for whi[...]

Page 4 SPECIFIC SAFETY RULES AND/OR SYMBOLS W ARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to cause cancer, birth defects or other repro- ductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and [...]

Page 5 SYMBOLS SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time Alternating Current Type or a characteristic of current --- Direct Current Type or a characteristic of current n 0 No Load Speed Rotational speed, at no load .../min Revolutions or Reciprocation Per Minute Rev[...]

Page 6 FEA TURES PRODUCT SPECIFICATIONS: DRILL-DRIVER HP1442M HP1802M Chuck 3/8 in. Keyless 1/2 in. Keyless Motor DC Motor 14.4 Volt DC Motor 18 Volt Gear Train Two Speed Two Speed Switch Variable Speed Variable Speed No Load Speed 0-330 RPM (Low) 0-350 RPM (Low) 0-1100 RPM (High) 0-1300 RPM (High) Clutch 24 Positions 24 Positions Charger Input 120[...]

Page 7 20 24 5 FEA TURES KEYLESS CHUCK BIT STORAGE AREA TORQUE ADJUSTMENT RING SWITCH TRIGGER LEVEL MODEL HP1442M MODEL HP1802M Fig. 1 Fig. 1a BA TTERY P ACK DIRECTION OF ROT ATION SELECTOR TWO SPEED GEAR TRAIN (HI-LO) MAG TRA Y™ (SCREW HOLDER) T OP VIEW OF LEVEL FOR HORIZONTAL DRILLING END VIEW OF LEVEL FOR VERTICAL DRILLING 20 24 5 KEYLESS CHUC[...]

Page 8 OPERA TION Fig. 2 W ARNING: If any parts are missing, do not operate tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. LED FUNCTION OF CHARGER See Figure 2. LED WILL BE LIGHTED T O INDICA TE ST A TUS OF CHARGER AND BA TTERY P ACK: ■ Red LED lighted = Fast Charging Mode ■ Green L[...]

Page 9 20 24 5 20 24 5 OPERA TION Fig. 5 Fig. 4 SWITCH See Figure 4. Your drill starts and stops by depressing and releasing the switch trigger. Release the switch trigger to turn drill OFF . VARIABLE SPEED See Figure 4. Your drill has a variable speed feature in the switch. The switch delivers higher speed and torque with increased trigger pressur[...]

Page 10 20 24 5 OPERA TION KEYLESS CHUCK See Figure 6. A keyless chuck has been provided with your drill to allow for easy installation and removal of bits. As the name implies, you can hand tighten or release drill bits in the chuck jaws. Grasp and hold the collar of the chuck with one hand. Rotate the chuck body with your other hand. The arrows o[...]

Page 11 20 24 5 OPERA TION WRONG CHUCK JA WS DRILL BIT CHUCK COLLAR CHUCK BODY INSTALLING BITS ■ Place the direction of rotation selector in center position. This will lock the switch trigger in the off position. See Figure 4. ■ Open or close the chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Als[...]

Page 12 20 20 24 5 20 24 5 OPERA TION SCREWDRIVING T ORQUE ADJUSTMENT (Driving power of your drill-driver) When using your drill-driver for various driving applications, it becomes necessary to increase or decrease the torque in order to help prevent the possibility of damaging screw heads, threads, workpiece, etc. In general, torque intensity shou[...]

Page 13 OPERA TION W ARNING: Always wear safety goggles or safety glasses with side shields when operating tool. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury . DRILLING See Figure 14. When drilling hard, smooth surfaces, use a center punch to mark the desired hole location. This will pre[...]

Page 14 20 24 5 20 24 5 OPERA TION CHUCK REMOV AL See Figures 15, 16, and 17. ■ Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. ■ Insert a 5/16 inch or larger hex key wrench into the chuck of your drill and tighten the chuck jaws securely . ■ T ap the hex key wrench sharply with a mallet[...]

Page 15 MAINTENANCE W ARNING: When servicing use only identical Ryobi replacement parts. Use of any other parts can create a hazard or cause product damage. A void using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use a clean cloth to remove[...]

OPERA TOR'S MANUAL CORDLESS DRILL-DRIVER MODEL NOS. HP1442M / HP1802M R YOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson, SC 29625 Post Of fice Box 1207, Anderson, SC 29622-1207 Phone 1-800-525-2579 www .ryobitools.com 972000-874 7-01 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or servic[...]