Saab 9-7X manual

Seats and Restraint System ............................. 1 - 1 Front Seats ............................................... 1 - 2 Rear Seats ............................................... 1 - 8 Safety Belts ............................................. 1-10 Child Restraints ....................................... 1-28 Airbag System ................[...]

Saab Automobile, Saab Cars USA, SAAB, Saab 9-7X, 9-7X and the Saab Emblem are registered trademarks of Saab Automobile, AB. This manual includes the latest information at the time it was printed. Saab reserves the right to make changes after that time without further notice. For vehicles first sold in Canada, substitute the name “General Motors [...]

Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning. { CAUTION: These mean there is something that could hurt you or othe[...]

Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 0 : Adjustable Pedals 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio Steering Wheel Controls or OnStar ® $ : Brake System Warning Light " [...]

Front Seats ..................................................... .1-2 Power Seats ................................................. .1-2 P o w e r L u m b a r .............................................. .1-2 Heated Seats ................................................ .1-3 Memory Seat ................................................ .1-3 Power[...]

Front Seats Power Seats The power seat controls are located on the outboard side of the seat cushions. • Move the seat forward or rearward by sliding the horizontal control forward or rearward. • Raise or lower the front part of the seat cushion by moving the front of the horizontal control up or down. • Raise or lower the rear part of the se[...]

Heated Seats Your vehicle has heated front seats. The buttons used to control this feature are located on the front door armrests. The engine must be running for the heated seat feature to work. To heat the entire seat, press the horizontal button with the heated seat and seatback symbol. Press the button to cycle through the temperature settings o[...]

To store the memory settings: 1. Adjust the driver’s seat, including the seatback recliner and lumbar and the adjustable pedals, if equipped, to the desired position. See Adjustable Throttle and Brake Pedal on page 2-22 for more information. 2. Press and hold the 1 or 2 button of the memory control for three seconds. A double chime will sound to [...]

To repeat the procedure for a second driver, follow the preceding steps, but press the other numbered memory control button. To recall the easy exit seat position: • Press the easy exit seat button on the memory control while the vehicle is in PARK (P). The seat will move to the stored exit position. • Or, if the easy exit seat feature is activ[...]

{ CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries. The lap belt cannot do its job either. In a crash the belt c[...]

Head Restraints Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head. This position reduces the chance of a neck injury in a crash. Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the head restraint dow[...]

Rear Seats Rear Seat Operation Your vehicle has flip and fold second row seats which provide additional cargo space. To flip and fold the seat(s), do the following: 1. Pull up on the loop located where the seat cushion meets the seatback and flip the seat cushion forward. Notice: Folding a rear seat with the safety belts still fastened may cause[...]

To return the seat(s) to the original position, do the following: { CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. 1. Lift the seatback until it locks into the upright position. Push and[...]

Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. { CAUTION: Do not let anyone ride where a safety belt cannot be worn properly. In a crash, if you or your passenger(s) are not wearing safety belts, the injuries can be mu[...]

Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Take the simplest vehicle. Suppose it is just a seat on wheels. Put someone on it. 1-11[...]

Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... 1-12[...]

or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. 1-13[...]

Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted. And you can unbuckle a safety[...]

How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 1-28 or Infants and Young Children on page 1-31 . Follow[...]

Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit snugly against your body. 1-16[...]

Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way. { CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug o[...]

Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries. Always buckle your belt into th[...]

Q: What is wrong with this? A: The belt is over an armrest. { CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be s[...]

Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much[...]

Q: What is wrong with this? A: The belt is behind the body. { CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury. You might also slide under the lap belt. The belt force w[...]

Q: What is wrong with this? A: The belt is twisted across the body. { CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to fix it. 1-22[...]

Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index. 2. Pick up the latch plate and pull the belt across you. Do not let it get [...]

4. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. To unlatch the belt, push the button on the buckle. The belt should return to its stowed position. Before a door is closed, be sure the safety belt is out o[...]

Safety Belt Pretensioners This vehicle has safety belt pretensioners for the front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly. They can help tighten the safety belts during the early stages of a moderate to severe frontal or near frontal crash if the threshold conditions for [...]

3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. { CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. Thes[...]

4. Buckle, position, and release the safety belt as described previously in this section. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide. Slide the guide back onto its storage clip located between the interior body an[...]

Safety Belt Extender If the safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/retailer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you. To help avoid personal injury, do not let someone else use it, and[...]

The manufacturer’s instructions that come with the booster seat state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below fit test: • Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue. If no, return to the booster seat. • Buckle [...]

{ CAUTION: Never do this. Never allow two children to wear the same safety belt. The safety belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A safety belt must be used by only one person at a time. { CAUTION: Never do this. Never allow a child to wear the safety belt with th[...]

Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age[...]

{ CAUTION: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) infant will suddenly become a 240 lb (110 kg) force on a person’s arms. An infant shoul[...]

{ CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat. It is also better to secure a forward-facing child restraint in a rear seat. If you must secur[...]

Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the m[...]

{ CAUTION: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure. This alone could cause serious or fatal injurie[...]

A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. Securing an Add-On Child Restraint in the Vehicle { CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Se[...]

To help reduce the chance of injury, the child restraint must be secured in the vehicle. Child restraint systems must be secured in vehicle seats by lap belts or the lap belt portion of a lap-shoulder belt, or by the LATCH system. See Lower Anchors and Tethers for Children (LATCH) on page 1-39 for more information. A child can be endangered in a cr[...]

Where to Put the Restraint According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restr[...]

When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. Wherever a child restraint is installed, be sure to secure the child restraint properly. Keep in mind that an unsecured child restraint can move around in a collision or sudden stop a[...]

Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tet[...]

Your child restraint may have a single tether (A) or a dual tether (C). Either will have a single attachment (B) to secure the top tether to the anchor. Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires tha[...]

The labels are located above a flap, at the base of the seatback, in the rear outside seating positions. The anchors are located under the flap. In order to get to the anchors you will need to pull the strap at the center of the seat where the seat cushion meets the seatback. This will allow you to fold the seat cushion up and out of the way. Lif[...]

Securing a Child Restraint Designed for the LATCH System { CAUTION: If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Install a LATCH-type child restraint properly using the anchors, or use the vehicle’s safet[...]

{ CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Buckle any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child[...]

If the position you are using does not have a headrest or head restraint and you are using a single tether, route the tether over the seatback. If the position you are using does not have a headrest or head restraint and you are using a dual tether, route the tether over the seatback. Fold down the headrest or head restraint and route the single te[...]

Securing a Child Restraint in a Rear Outside Seat Position When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. If your child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-39 for how and w[...]

4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use[...]

6. If the child restraint has a top tether, follow the child restraint manufacturer’s instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 1-39 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure. To remove the child restraint, unbuckle [...]

{ CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front passenger ai[...]

3. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. 4. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary. 5. P[...]

6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. 7. Push and pull [...]

Airbag System The vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. • A roof-rail airbag for the driver and the passenger seated directly behind the driver. • A roof-rail airbag for the right front passenger and the passenger seated directly behind the right front passeng[...]

{ CAUTION: Airbags inflate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inflates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward. Safety belts help keep you in posit[...]

Where Are the Airbags? The driver’s frontal airbag is in the middle of the steering wheel. The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. 1-54[...]

The roof-rail airbags for the driver, right front passenger, and second row outboard passengers are in the ceiling above the side windows. { CAUTION: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating a[...]

When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inflate if the impact exceeds a predetermined deployment threshold. [...]

Your vehicle has roof-rail airbags. See Airbag System on page 1-52 . Roof-rail airbags are intended to inflate in moderate to severe side crashes. In addition, these roof-rail airbags are intended to inflate during a rollover. Roof-rail airbags will inflate if the crash severity is above the system’s designed threshold level. The threshold lev[...]

Rollover capable roof-rail airbags are designed to help contain the head and chest of occupants in the outboard seating positions in the first and second rows. The rollover capable roof-rail airbags are designed to help reduce the risk of full or partial ejection in rollover events, although no system can prevent all such ejections. But airbags wo[...]

In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for the airbag system. If you do not get them, the airbag sy[...]

The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. The driver airbags and roof-rail airbags are not affected by the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger seat. The sensors are designed to detect the presence of a[...]

The passenger sensing system is designed to turn off the right front passenger frontal airbag if: • The right front passenger seat is unoccupied. • The system determines that an infant is present in a rear-facing infant seat. • The system determines that a small child is present in a child restraint. • The system determines that a small chi[...]

If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers. 4. Reinstall the child restraint followi[...]

If the Of f Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. If this happens, use the following steps to allow the system to detect that person and enable the right front passenger fro[...]

Additional Factors Af fecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints” in the Index for additional information about the importance of proper rest[...]

Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change your vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly. Changing or mov[...]

Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job. See your dealer/retaile[...]

Replacing Restraint System Parts After a Crash { CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any ne[...]

✍ NOTES 1-68[...]

Keys .............................................................. .2-3 Remote Keyless Entry (RKE) System ............... .2-4 Remote Keyless Entry (RKE) System Operation .................................................. .2-5 Doors and Locks ............................................ .2-7 Door Locks .............................................[...]

OnStar ® System ............................................ .2-35 Universal Home Remote System ..................... .2-38 Universal Home Remote System Operation (With One Triangular LED) .......................... .2-39 Storage Areas ............................................... .2-43 Glove Box .................................................[...]

Keys { CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed i[...]

The key code number tells your dealer/retailer or a qualified locksmith how to make extra keys. Keep this number in a safe place. If you lose your keys, you will be able to have new ones made easily using this number. Your selling dealer/retailer should also have this number. Notice: If you ever lock your keys in the vehicle, you may have to damag[...]

If there is a decrease in the RKE operating range, try this: • Check the distance. The transmitter may be too far from the vehicle. Stand closer during rainy or snowy weather. • Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again. • Check t[...]

Programming Transmitters to the Vehicle Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer. When the replacement transmitter is programmed to the vehicle, all remaining transmitters must also be programmed. Any lost or stolen trans[...]

Doors and Locks Door Locks { CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly [...]

Power Door Locks The power door lock switches are located on the driver’s and front passenger’s door armrests. Press the lock symbol to lock all of the doors. To unlock the doors, press the other side of the switch. Delayed Locking This feature delays the locking of the doors and the liftgate when using the power lock or the remote keyless entr[...]

Programmable Automatic Door Locks Your vehicle is equipped with an automatic lock/unlock feature which enables you to program your vehicle’s power door locks. You can program this feature through the Driver Information Center (DIC), or by the following method. See DIC Vehicle Customization on page 3-51 . Programmable Locking Feature Following are[...]

Programmable Unlocking Feature The following is the list of available programming options: Mode 1: Driver’s door unlocks when the transmission is shifted into (P) Park. Mode 2: All doors unlock when the transmission is shifted into (P) Park. Mode 3: All doors unlock when the key is removed from the ignition. Mode 4: No automatic door unlock. The [...]

Rear Door Security Locks Your vehicle may have this feature. You can lock the rear doors so they cannot be opened from the inside by passengers. To use one of these locks do the following: 1. Open one of the rear doors. You will find a security lock lever located on the inside edge of each rear door. 2. Move the lever down to engage the security l[...]

Liftgate/Liftglass { CAUTION: It can be dangerous to drive with the liftgate or liftglass open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the liftgate open or if electrical wiring or other cable connections must pass through the seal be[...]

Windows { CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. 2-13[...]

Power Windows { CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing[...]

Express-Down Window AUTO (Express-down): The driver’s and front passenger’s window switches have an express-down feature that allows you to lower the window without holding the switch down. Press down briefly on the driver’s or front passenger’s window switch labeled AUTO to activate the express-down feature. Lightly tap the switch to open[...]

Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal. Content Theft-Deterrent Your vehicle is equipped with a content theft-deterrent alarm system. Here is how to operate the system: 1. Open the door. 2. Lock the door with the po[...]

Testing the Alarm The alarm can be tested by following these steps: 1. From inside the vehicle, lower the driver’s window and open the driver’s door. 2. Activate the system by locking the doors with the power door lock switch while the door is open, or with the remote keyless entry transmitter. 3. Get out of the vehicle, close the door and wait[...]

PASS-Key ® III Electronic Immobilizer Operation Your vehicle is equipped with the PASS-Key III (Personalized Automotive Security System) theft-deterrent system. PASS-Key III is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. You do not have to manually arm or disarm the system. The sec[...]

To program the new key: 1. Verify that the new key has PK3 stamped on it. 2. Insert the current driver’s key in the ignition and start the engine. If the engine will not start, see your dealer/retailer for service. 3. After the engine has started, turn the key to LOCK/OFF, and remove the key. 4. Insert the key to be programmed and turn it to ON/R[...]

Ignition Positions The ignition switch is located on the center console, and has four different positions. In order to shift out of P (Park), turn the ignition to ON/RUN and apply the brake pedal. Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key. Use the correct key, make sure it is all[...]

Retained Accessory Power (RAP) These vehicle accessories may be used for up to 10 minutes after the engine is turned off: • Audio System • DVD Player • Power Windows • Overhead console • Sunroof (if equipped) These features work when the key is in ON/RUN or ACC/ACCESSORY. Once the key is turned from ON/RUN to LOCK/OFF, these features will[...]

2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or − 18°C), it could be flooded with too much gasoline. Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START for up to a maximum of 15 seconds. Wait at least 15 seconds between each try, to all[...]

Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below 0°F ( − 18°C). Vehicles with an engine coolant heater should be plugged in at least four hours before starting the vehicle. An internal thermostat in the plug-end of the cord may exist [...]

Active Fuel Management™ If the vehicle has a 5.3L V8 engine, it has Active Fuel Management™. This system allows the engine to operate on either all or half of its cylinders, depending on driving conditions. When less power is required, such as cruising at a constant vehicle speed, the system will operate in the half cylinder mode, allowing the [...]

If you cannot shift out of P (Park), ease pressure on the shift lever and push the shift lever all the way into P (Park) as you maintain brake application. Then press the shift lever button and move the shift lever into another gear. See Shifting Out of Park on page 2-29 . R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while[...]

Downshifting the transmission in slippery road conditions could result in skidding, see “Skidding” under Loss of Control on page 4-12 . D (Drive) can be used when towing a trailer, carrying a heavy load, driving on steep hills, or for off-road driving. You may want to shift the transmission to 3 (Third) or, if necessary, a lower gear selection [...]

Parking Brake To set the parking brake, hold the regular brake pedal down with your foot and pull up on the parking brake lever located between the seats. To release the parking brake, hold the regular brake pedal down. Pull the parking brake lever up until you can press in the button at the end of the lever. Hold the button in as you move the park[...]

Shifting Into Park { CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level [...]

Torque Lock If you are parking on a hill and you do not shift the transmission into P (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may find it diff icult to pull the shift lever out of P (Park). This is called “torque lock.” To prevent torque lock, set the parking brake and then[...]

Parking Over Things That Burn { CAUTION: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust { CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even[...]

Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause[...]

Mirrors Automatic Dimming Rearview Mirror The vehicle may have an automatic dimming rearview mirror with a compass display. O (On/Off): Press to turn the dimming feature on or off. Automatic Dimming Mirror Operation Automatic dimming reduces the glare of lights from behind the vehicle. The dimming feature comes on and the indicator light illuminate[...]

Compass Variance The mirror is set to zone eight. Adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, such as during a long distance cross-country trip, it is necessary to adjust for compass variance. If not adjusted to account for compass variance, your compass could give false reading[...]

Outside Power Mirrors The outside power mirror control is located on the driver’s door. 1. Turn the knob toward the mirror you desire to adjust. 2. Move the control in the direction you want the mirror to go. 3. Adjust the mirror in all four directions to see the side of your vehicle and the area behind your vehicle. 4. After adjusting each mirro[...]

OnStar ® System OnStar uses several innovative technologies and live advisors to provide a wide range of safety, security, information, and convenience services. If the airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location. If the keys are locked in[...]

OnStar Services Available with the Safe & Sound Plan • Automatic Notification of Airbag Deployment • Advanced Automatic Crash Notification (AACN) (If equipped) • Link to Emergency Services • Roadside Assistance • Stolen Vehicle Location Assistance • Remote Door Unlock/Vehicle Alert • OnStar Vehicle Diagnostic Email • Remote Di[...]

OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses minutes to access location-based weather, local traff ic reports, and stock quotes. Press the phone button and give a few simple voice commands to browse through the various topics. See the OnStar Owner’s Guide for more information. This feature is o[...]

Location information about the vehicle is only available if the GPS satellite signals are unobstructed and available. The vehicle must have a working electrical system, including adequate battery power, for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service at any pa[...]

Universal Home Remote System Operation (With One Triangular LED) If there is one triangular Light Emitting Diode (LED) indicator light above the Universal Home Remote buttons, follow the instructions below. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security sy[...]

Programming the Universal Home Remote System For questions or help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated[...]

If the Universal Home Remote indicator light blinks rapidly for two seconds and then turns to a constant light, continue with the programming Steps 6 through 8. It may be helpful to have another person assist with the remaining steps. 6. After Steps 1 through 5 have been completed, locate inside the garage the garage door opener receiver (motor-hea[...]

Gate Operator and Canadian Programming If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up t[...]

Reprogramming a Single Universal Home Remote Button To reprogram any of the three Universal Home Remote buttons, repeat the programming instructions earlier in this section, beginning with Step 2. For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Off ices on page 7-6 . S[...]

Overhead Console For this vehicles with this feature, the overhead console may include reading lamps, a Universal Home Remote, and a moonroof switch. See the following for more information: • Reading Lamps on page 3-17 . • Universal Home Remote System on page 2-38 . • Moonroof on page 2-47 . Center Console Storage Grasp the front lever on the[...]

Crossrails can be purchased from your dealer/retailer. Notice: Loading cargo on the luggage carrier that weighs more than 200 lbs (91 kg) or hangs over the rear or sides of the vehicle can damage the vehicle. Load cargo so that it rests on the slats as far forward as possible and against the side rails, making sure to fasten it securely. Do not exc[...]

Cargo Cover The cargo cover can be used to cover items in the cargo area of the vehicle. To install the cargo cover, do the following: 1. Align the endcap with the pocket in the trim panel located behind the rear seat. 2. Squeeze the opposite endcap, align it with the pocket located on the opposite side of the trim panel and release. 3. Grasp the h[...]

Cargo Tie Downs Four cargo tie-downs are located in the rear compartment of the vehicle. The tie-downs can be used to secure small loads. Moonroof The vehicle may be equipped with a power sliding moonroof. The ignition must be turned to ON/RUN, ACC/ACCESSORY, or Retained Accessory Power (RAP) must be active to operate it. See Retained Accessory Pow[...]

✍ NOTES 2-48[...]

Instrument Panel Overview .............................. .3-4 Hazard Warning Flashers ............................... .3-6 H o r n ............................................................ .3-6 Tilt Wheel .................................................... .3-6 Turn Signal/Multifunction Lever ........................ .3-6 Turn and Lane-Change S[...]

Tire Pressure Light ...................................... .3-34 Malfunction Indicator Lamp ............................ .3-34 Oil Pressure Gage ....................................... .3-37 Security Light .............................................. .3-38 Cruise Control Light ..................................... .3-38 Reduced Engine Power Light[...]

✍ NOTES 3-3[...]

Instrument Panel Overview 3-4[...]

The main components of the instrument panel are the following: A. Outlet Adjustment on page 3-23 . B. Turn Signal/Multifunction Lever on page 3-6 . C. Audio Steering Wheel Controls on page 3-97 . D. Instrument Panel Cluster on page 3-25 . E. Windshield Wipers on page 3-8 . F. Hazard Warning Flashers on page 3-6 or Driver Information Center (DIC) on[...]

Hazard Warning Flashers | (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press | again to turn the flashers off. Horn To sound the horn, press the horn symbols on the steering wheel pad. Tilt Wheel The tilt l[...]

Turn and Lane-Change Signals An arrow on the instrument panel cluster flashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is complete. The lever returns to its starting posi[...]

Flash-to-Pass This feature lets high-beam headlamps be used to signal to a driver in front of you that you want to pass. It works even if the headlamps are in the automatic position. To use it, pull the turn signal lever toward you, then release it. If the headlamps are in the automatic position or on low beam, the high-beam headlamps turn on. They[...]

Windshield Washer L (Windshield Washer): Press the windshield washer paddle to spray washer fluid on the windshield. The wipers will clear the window and then either stop or return to the preset speed. { CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, [...]

Headlamp Washer For vehicles with headlamp washers, they clear debris from the headlamp lenses by soaking the lens with fluid, waiting for about five seconds, then rinsing away the loose debris. The headlamp washers are located under the headlamps. The headlamp washers activate for one wash-wait-rinse cycle when the front windshield washer button[...]

The cruise controls are located on the end of the turn signal/multifunction lever. R (On): Turns the system on. + (Resume/Accelerate): Makes the vehicle accelerate or resume to a previously set speed. T (Set): Press this button to set the speed. 9 (Off): Turns the system of f. Setting Cruise Control { CAUTION: If you leave your cruise control on wh[...]

Resuming a Set Speed Suppose the cruise control is set at a desired speed and then the brakes are applied. This disengages the cruise control. But it does not need to be reset. Once the vehicle is going about 25 mph (40 km/h) or more, move the cruise control switch briefly from R to S . The vehicle returns to the chosen speed and stays there. If t[...]

speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle’s speed down. When the brakes are applied this disengages the cruise control. Ending Cruise Control To turn off the cruise control, do one of the following: • Step lightly on the brake pedal, • move the cruise control switch to 9 ,o r • shift th[...]

Headlamps on Reminder A reminder tone sounds when the headlamps or parking lamps are manually turned on, if the driver’s door is open and the ignition is in LOCK/OFF or ACC/ACCESSORY. To turn the tone off, turn the knob all the way counterclockwise. In the automatic mode, the headlamps turn off once the ignition key is in LOCK/OFF. Daytime Runnin[...]

The system could also turn on the lamps when driving through a parking garage, heavy overcast weather or a tunnel. This is normal. There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems, so that driving under bridges or bright overhead street lights does n[...]

Instrument Panel Brightness Turn the knob clockwise or counterclockwise to brighten or dim the interior lights. To turn on the dome lamps, turn the knob completely clockwise as far as it will go. The dome lamps stay on until they are turned off. Dome Lamps The dome lamps automatically come on when a door is opened, unless the dome lamp override but[...]

Exit Lighting With exit lighting, the interior lamps will come on when you remove the key from the ignition. If the dome override is off, these lights will stay on for a short period of time and then will go out. Reading Lamps Press the indented part of the lenses on the reading lamps located in the overhead console to turn them on or off. Electric[...]

Battery Run-Down Protection This feature shuts off the dome, courtesy, and vanity lamps if they are left on for more than 20 minutes when the ignition is off. This helps to keep the battery from running down. If the battery run-down protection shuts off the interior lamps, it may be necessary to do one of the following to return to normal operation[...]

Climate Controls Dual Automatic Climate Control System With this system the heating, cooling and ventilation can be controlled on the vehicle. When the vehicle is first started and the climate control system is on, or if the climate control system has been turned on, the display shows the driver’s temperature setting for five seconds. Then it s[...]

Automatic Operation AUTO (Automatic): When automatic operation is active, the system controls the air delivery mode, fan speed, and temperature inside the vehicle. Use the steps below to place the entire system in automatic mode: 1. Press AUTO. When AUTO is selected, the air conditioning and air inlet are automatically controlled. The air condition[...]

w9x (Fan Control): Press the arrows to increase or decrease the fan speed. The display shows the selected fan speed and the driver side temperature setting for five seconds. C (Air Delivery Mode Control): Press to change the direction of the airflow in the vehicle. The air delivery modes will appear on the display as it is being adjusted. The dis[...]

You may notice a slight change in engine performance when the air-conditioning compressor shuts off and turns on again. This is normal. @ (Recirculation): Press to turn the recirculation mode on or off. An indicator light comes on to show that recirculation is on. This mode recirculates and helps to quickly cool the air inside the vehicle. It can b[...]

Outlet Adjustment Use the air outlets located in the center and on the sides of the instrument panel to direct the airflow. Operation Tips • Keep the hood and front air inlets free of ice, snow, or any other obstruction, such as leaves. • When entering the vehicle in cold weather, select maximum blower speed for a few moments before driving. T[...]

P (On/Off): Press to turn the rear climate controls on or off. The rear control only turns on if the front control is on and not in defrost mode. Climate Controls Personalization The vehicle has a Driver Information Center (DIC). Climate control settings can be stored and recalled for temperature, air delivery mode and fan speed for two different d[...]

Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically. United States version shown, Canada similar 3-25[...]

Speedometer and Odometer The speedometer the vehicle speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). The odometer mileage can be checked without the vehicle running. Press the trip stem located on th[...]

Safety Belt Reminders Driver Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind the driver to fasten the safety belt, unless the driver safety belt is already buckled. The driver safety belt light comes on and stays on for several seconds, then flashes for several more. This chime and light are repe[...]

Airbag Readiness Light The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system,[...]

Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 1-59 for important safety information. The rearview mirror has a passenger airbag status indicator. When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several s[...]

Charging System Light This light comes on briefly when the ignition key is turned to START, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer. The light should go out once the engine starts. If it stays on, or comes on while driving, there could be a problem with the [...]

charging system is not able to provide full power at engine idle. As engine speeds are increased, this condition should correct itself as higher engine speeds allow the charging system to create maximum power. You can only drive for a short time with the reading in either warning zone. If you must drive, turn off all unnecessary accessories. Readin[...]

Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. If the ABS light stays on, turn the ignition off. If the light c[...]

StabiliTrak ® Indicator Light This warning light should come on briefly when the engine is started. During most driving conditions, this light will not come on. If the StabiliTrak ® System is actively controlling the stability and/or traction of the vehicle, this light will flash. This is normal. This light will come on if any portion of the sy[...]

Tire Pressure Light For vehicles with a tire pressure light, this light comes on briefly when the engine is started and provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is significantly underinflated. A tire pressure message in the Driver I[...]

Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might not wo[...]

Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected by doing the following: • Make sure the fuel cap is fully installed. See Filling the Tank on page 5-8 . The diagnostic system can determine if the fuel cap has been le[...]

Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: • The vehicle will not p[...]

A reading in the low pressure zone may be caused by a dangerously low oil level or other problems causing low oil pressure. { CAUTION: Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper en[...]

Reduced Engine Power Light This light comes on when a noticeable reduction in the vehicle’s performance occurs. The vehicle can be driven at a reduced speed when the reduced engine power light is on, but acceleration and speed may be reduced. The performance may be reduced until the next time you drive your vehicle. If this light stays on, see yo[...]

Service All-Wheel Drive Light This light should come on briefly when you turn on the ignition, as a check to show you it is working. The service all-wheel drive light comes on to indicate that there may be a problem with the drive system and service is required. Malfunctions can be indicated by the system before any problem is apparent, which may [...]

Fuel Gage When the ignition is on, the fuel gage tells you about how much fuel you have remaining. An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. Here are four things that some owners ask about. None of these show a problem with your fuel gage: • At the gas station, the gas pump shuts off before the gage reads fu[...]

Driver Information Center (DIC) The Driver Information Center (DIC) display is located on the instrument panel cluster, below the speedometer. The DIC buttons are located on the center of the instrument panel, above the radio. The DIC can display information such as the trip odometer, fuel economy, customization features, and warning/status message[...]

The DIC has different modes which can be accessed by pressing the four DIC buttons located on the center of the instrument panel, above the radio. These buttons are fuel information, trip information, customization, and select. The button functions are detailed in the following pages. Fuel Information Button r (Fuel Information): Press this button [...]

Trip Information Button 3 (Trip Information): Press this button to scroll through the odometer, trip odometers, tire pressures, and timer. Odometer: Press the trip information button until ODOMETER appears on the display. This mode shows the total distance the vehicle has been driven in either miles or kilometers. Pressing the trip stem located on [...]

the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes, and 59 seconds (99:59:59), after which the display will roll back to zero. To stop the counting of time, press the select button briefly while TIMER is displayed. [...]

CHANGE ENGINE OIL This message displays when the engine oil needs to be changed and service is required for your vehicle. See Scheduled Maintenance on page 6-4 and Engine Oil on page 5-18 for more information. Also see Engine Oil Life System on page 5-22 for information on how to reset the message. This message clears itself after 10 seconds until [...]

This message displays and a chime sounds if the cooling system temperature gets hot. See Engine Overheating on page 5-34 for the proper course of action. This message clears when the coolant temperature drops to a safe operating temperature. FRONT FOG LAMPS OFF This message displays if the fog lamps are turned off. The message clears after 10 secon[...]

OIL PRESSURE LOW/STOP ENGINE Notice: If you drive your vehicle while the engine oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the Driver Information Center (DIC), stop the vehicle as soon as possible. Do not drive the vehicle until the cause of the low oil pressure is corrected. See Engine Oil on page[...]

If the message is still displayed, or appears again when you begin driving, the brake system needs service. See your dealer/retailer. SERVICE CHARGING SYS (System) This message displays if there is a problem with the battery charging system. Under certain conditions, the charging system light may also turn on in the instrument panel cluster. See Ch[...]

STABILITRAK OFF This message displays when you press the StabiliTrak button for more than five seconds or when stability control has been automatically disabled. The StabiliTrak button is located on the transmission shift handle. To limit wheel spin and realize the full benefits of the stability enhancement system, you should normally leave Stabi[...]

DIC Vehicle Customization Your vehicle may have customization capabilities that allow you to program some features to one setting based on your preference. All of the customizable options listed may not be available on your vehicle. Only the options available display on the Driver Information Center (DIC). The default settings for the customization[...]

Unlock Doors Press q until UNLOCK DOORS: IN PARK appears in the display. To select your preference for automatic unlocking, press r while UNLOCK DOORS: IN PARK is displayed on the DIC. Pressing r will scroll through the following settings: UNLOCK DOORS: IN PARK (default): All of the doors will unlock when the vehicle is shifted into P (Park). UNLOC[...]

Unlock Feedback Press q until UNLOCK FEEDBACK: LAMPS appears in the display. To select your preference for the feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter, press r while UNLOCK FEEDBACK: LAMPS is displayed on the DIC. Pressing r will scroll through the following settings: UNLOCK FEEDBACK: LAM[...]

Perimeter Lights Press q until PERIMETER LIGHTS: ON appears in the display. To select your preference for perimeter lighting, press r while PERIMETER LIGHTS: ON is displayed on the DIC. Pressing r will scroll through the following settings: PERIMETER LIGHTS: ON (default): The headlamps and back-up lamps will come on for 40 seconds, if it is dark en[...]

Seat Recall Press q until SEAT RECALL: OFF appears in the display. To select your preference for recall of the driver’s memory seat and adjustable pedals, if your vehicle has this feature, press r while SEAT RECALL: OFF is displayed on the DIC. Pressing r will scroll through the following settings: SEAT RECALL: OFF (default): The driver’s memor[...]

Language Press q until LANGUAGE: ENGLISH appears in the display. To select your preference for display language, press r while LANGUAGE: ENGLISH is displayed on the DIC. Pressing r will scroll through the following settings: ENGLISH (default): All messages will appear in English. FRANCAIS: All messages will appear in French. ESPANOL: All messages w[...]

Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving. This system provides access to [...]

Radio(s) The vehicle has one of these radios as its audio system. If the vehicle has a Bose ® audio system, it has 6 channels of custom equalization. Radio with CD (MP3) Radio with Six-Disc CD Player 3-58[...]

XM™ Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. During your trial or when you subscribe, you will get unlimited access to XM Radio Onl[...]

Finding a Station BAND: Press to switch between FM1, FM2, AM, or X M 1o rX M 2 . e (Tune): Turn to select radio stations. t SEEK u : Press and release to go to the previous or the next station and stay there. The radio only seeks stations with a strong signal that are in the selected band. To scan stations, press and hold either arrow for more than[...]

Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2, can be programmed on the six numbered pushbuttons. To program stations: 1. Turn the radio on. 2. Press BAND to select FM1, FM2, AM, or XM1 or XM2. 3. Tune in the desired station. 4. Press AUTO EQ (automatic equalization) to select the equalization. 5. Pres[...]

Adjusting the Speakers (Balance/Fade) e (Balance/Fade): To adjust the balance between the right and the left speakers, push and release e until BAL (balance) displays. Turn e to move the sound toward the right or the left speakers. To adjust the fade between the front and the rear speakers, push and release e until FADE displays. Turn e to move the[...]

Radio Messages CAL ERR (Calibration Error): Displays if the radio is no longer calibrated properly for the vehicle. The vehicle must be returned to your dealer/retailer for service. LOC (Locked): Displays when the THEFTLOCK ® system has activated. Take the vehicle to your dealer/retailer for service. If any error occurs repeatedly or if an error c[...]

3. Once the light stops flashing and turns green, INSERT CD # displays, load a CD. Insert the CD partway into the slot, label side up. The player pulls the CD in. Once the CD is loaded, the indicator light flashes again. After the light stops flashing and turns green, load another CD. The CD player takes up to six CDs. Do not try to load more th[...]

Care of CDs Sound quality can be reduced due to CD-R quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R has been handled. Handle them carefully. Store CD-R(s) in their original cases or other protective cases and away from direct sunlight and dust. The CD player scans the bottom surface of the di[...]

N (Repeat): With the repeat setting, one track or an entire CD can be repeated. To use repeat: • To repeat the current track, press and release N . RPT ON displays. Press N again to turn off repeat play. RPT OFF displays. • For the Radio with Six-Disc CD player, repeat the CD you are listening to by pressing and holding N for two seconds. RPT O[...]

the display, track or elapsed time, press this button until the desired option displays, then hold the button for two seconds. One beep sounds and the selected display becomes the default. BAND: Press to listen to the radio when a CD is playing. The inactive CD remains inside the radio for future listening. B (CD): Press to play a CD when listening[...]

Using an MP3 MP3 CD-R Disc MP3 Format If you burn an MP3 disc on a personal computer: • Make sure the MP3 files are recorded on a CD-R disc. • Do not mix standard audio and MP3 files on one disc. • Make sure playlists have a .mp3 or .wpl extension, other file extensions might not work. • Files can be recorded with a variety of fixed or [...]

Empty Directory or Folder If a root directory or a folder exists somewhere in the file structure that contains only folders/subfolders and no compressed files directly beneath them, the player advances to the next folder in the file structure that contains compressed audio files. The empty folder is not displayed. No Folder When the CD contains[...]

File System and Naming The song name that is displayed is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the file name without the extension (such as .mp3) as the track name. Track names longer than 32 characters or four pages are shortened. Parts of words on the last page of[...]

To play all the tracks on the CD in random order, press and hold 4 y for two seconds. A beep sounds and CD RDM displays. This feature does not work with playlists. When in random, pressing and releasing either SEEK arrow takes the CD to the next or previous randomized track. Press and release 4 y again to turn off random play. NO RDM displays. 5 ! [...]

4 (Information): INFO displays whenever a current track has ID3 tag information. Press 4 to display the artist name and album contained in the tag. INFO disappears from the display when the information in the ID3 tag has finished. BAND: Press to listen to the radio when a CD is playing. The inactive CD remains inside the radio for future listening[...]

CH Off Air: This channel is not currently in service. Tune in to another channel. Off Air: This channel is not currently in service. Tune to another channel. CH Unauth: This channel is blocked or cannot be received with your XM Subscription package. Unauth: This channel is blocked or cannot be received with your XM Subscription package. CH Unavail:[...]

Navigation/Radio System For vehicles with a navigation radio system, see the separate Navigation System manual. Bluetooth ® Vehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Profile to make and receive phone calls. The system can be used while the key is in ON/RUN or ACC/ACCESSORY position. The range of the[...]

Pairing A Bluetooth enabled cell phone must be paired to the in-vehicle Bluetooth system first and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone. If a Bluetooth phone is not connected, calls will be made using OnStar ® Hands-Free Calling, if a[...]

Listing All Paired and Connected Phones 1. Press and hold g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “List”. The system lists all the paired Bluetooth devices. If a phone is connected to the vehicle, the system will[...]

Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press and hold g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Store”. The system responds with “Store, number please” followed by a tone. 3. Say the complete phone number to be stored[...]

3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. • If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number. • To hear all of the numbers recognized by the system, say “Veri[...]

3. Say the name tag to be deleted. The system responds with “Would you like to delete, <name tag>? Please say yes or no”. • If the name tag is correct, say “Yes” to delete the name tag. The system responds with “OK, deleting <name tag>, returning to the main menu.” • If the name tag is incorrect, say “No”. The system[...]

Using the Digit Dial Command 1. Press and hold g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Digit Dial”. The system responds with “Digit dial using <phone name>, please say the first digit to dial” followed by a tone. 3. Say the digit to be dialed one at a time. Following each digit, the system [...]

Receiving a Call When an incoming call is received, the audio system mutes and a ring tone is heard in the vehicle. Press g and begin speaking to answer the call. Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. • Press g to answer an incoming call when another call is active.[...]

To Cancel Mute 1. Press g . The system responds with “Ready” followed by a tone. 2. After the tone, say “Mute Call”. The system responds with “Resuming call”. Transferring a Call Audio can be transferred between the in-vehicle Bluetooth system and the cell phone. To Transfer Audio to the Cell Phone During a call with the audio in the ve[...]

Dual Tone Multi-Frequency (DTMF) Tones The in-vehicle Bluetooth system can send numbers and numbers stored as name tags during a call. This is used when calling a menu driven phone system. Account numbers can be programmed into the phonebook for retrieval during menu driven calls. Sending a Number During a Call 1. Press g . The system responds with[...]

Other Information The Bluetooth ® word mark and logos are owned by the Bluetooth ® SIG, Inc. and any use of such marks by General Motors is under license. Other trademarks and trade names are those of their respective owners. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device m[...]

Headphones The RSE system includes two sets of wireless headphones. Each set of headphones has an ON/OFF control. An indicator light will illuminate on the headphones when they are on. If the light does not illuminate, the batteries may need to be replaced. See “Battery Replacement” following for more information. Each set of headphones has a v[...]

To use the auxiliary inputs on the RSE system, connect an external auxiliary device to the color-coded RCA jacks and turn both the auxiliary device and the RSE system power on. If the RSE system had been previously in the DVD player mode, pressing the SRCE button on the faceplate or the remote control will switch the RSE system between the auxiliar[...]

Video Screen The video screen is located in the overhead console. To use the video screen, push forward on the release latch and the screen will fold down. Adjust the screen’s position as desired. When the video screen is not in use, push it up into its latched position. The DVD player and display will continue to operate when the screen is in th[...]

DVD Player Buttons (Without Sunroof) O (Power): Press to turn the RSE system on and off. The power indicator light illuminates when the power is on. X (Eject): Press to eject a DVD or CD. SRCE (Source): Press to switch between the DVD player and an auxiliary source. c (Stop): Press to stop playing, rewinding, or fast forwarding a DVD or CD. Press t[...]

DVD Player Buttons (With Sunroof) s (Play/Pause): Press to start play of a DVD or CD. Press while a DVD or CD is playing to pause it. Press again to continue the play of the DVD or CD. c / X (Stop/Eject): Press to stop playing, rewinding, or fast forwarding a DVD or CD. Press this button twice to return to the beginning of the DVD. Press and hold t[...]

Remote Control To use the remote control, aim it at the transmitter window below the video screen and press the desired button. Direct sunlight or very bright light may affect the ability of the RSE system to receive signals from the remote control. If the remote control does not seem to be working, the batteries may need to be replaced. See “Bat[...]

e (Audio): Press to display a menu that only appears while a DVD is being played. The format and content of this function will vary for each disc. r (Fast Reverse): Press to fast reverse the DVD or CD. To stop fast reversing, press again. This button might not work when the DVD is playing the copyright information or the previews. SRCE (Source): Pr[...]

s (Play/Pause): Press to start play of a DVD or CD. Press while a DVD or CD is playing to pause it. Press again to continue the play of the DVD or CD. When the DVD is playing, press this button then press the fast forward button. The DVD continues playing in a slow play mode. To cancel slow play mode, press this button. u (Next Track/Chapter): Pres[...]

Problem Recommended Action In auxiliary mode, the picture moves or scrolls. Check the auxiliary input connections at both devices. Change the Video Format to PAL or NTSC. See “Stereo RCA Jacks” previously for how to change the video format. The language in the audio or on the screen is wrong. Check the audio or language selection in the main DV[...]

Problem Recommended Action Sometimes the wireless headphone audio cuts out or buzzes. Check for obstructions, low batteries, reception range, and interference from cellular telephone towers or by using a cellular telephone in the vehicle. Check that the headphones are facing the front of the vehicle. I lost the remote and/or the headphones. See you[...]

DVD Distortion There may be an experience with audio distortion in the wireless headphones when operating cellular phones, scanners, CB radios, Global Positioning Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. It might be necessary to turn off the DVD player when operating one of these devices in or near the vehicle. * Excludes the [...]

P (Power): Press to turn the RSA on or off. The rear speakers are muted when the power is turned on. u (Volume): The left-hand knob controls the headphone outlet on the left and the right-hand knob controls the headphone outlet on the right. Turn either knob clockwise to increase the volume and counterclockwise to decrease the volume. SRCE (Source)[...]

Theft-Deterrent Feature THEFTLOCK ® is designed to discourage theft of the vehicle’s radio by learning a portion of the Vehicle Identification Number (VIN). The radio does not operate and LOCKED displays if the radio is stolen or moved to a different vehicle. When the when the ignition is in the off position, a blinking red light on the upper l[...]

Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. AM The range for most AM st[...]

Cellular Phone Usage Cellular phone usage may cause interference with the vehicle’s radio. This interference may occur when making or receiving phone calls, charging the phone’s battery, or simply having the phone on. This interference causes an increased level of static while listening to the radio. If static is received while listening to the[...]

✍ NOTES 3-100[...]

Your Driving, the Road, and the Vehicle ........... .4-2 Driving for Better Fuel Economy ...................... .4-2 Defensive Driving .......................................... .4-2 Drunk Driving ................................................ .4-3 Control of a Vehicle ....................................... .4-3 Braking .........................[...]

Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. • Avoid fast starts and accelerate smoothly. • Brake gradually and avoid abrupt stops. • Avoid idling the engine for long periods of time. • When road and weather c[...]

Drunk Driving { CAUTION: Drinking and then driving is very dangerous. Your reflexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Do not drink and drive or ride with a driver who has been drinking. Ride home in a cab; [...]

Braking See Brake System Warning Light on page 3-31 . Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three-fourths of a second. But that is only an average. It might be less with one driver and as long as two or three [...]

Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that will help prevent a braking skid. When the engine is started and the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on. This is normal. If there is a p[...]

Braking in Emergencies ABS allows the driver to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking. Brake Assist This vehicle has a Brake Assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions. This feature uses the stability sys[...]

When the StabiliTrak system is both on and actively controlling the stability of the vehicle, the StabiliTrak light will blink for the duration of the event. The system may be heard or felt while it is working. This is normal. The StabiliTrak disable button is located on the transmission shift handle. The StabiliTrak system has three modes of opera[...]

StabiliTrak Of f In this mode, both stability control and part of the traction control system are disabled. The vehicle will still have brake-traction control, but will not be able to use the engine speed management system. System noises maybe heard as a result of the brake-traction control coming on. If the controller detects excessive wheel spin [...]

Notice: If the StabiliTrak ® light comes on due to heavy braking and/or because the traction control system has been continuously active, do not allow the wheel(s) of one axle to spin excessively. This could lead to damage to the transfer case and costly repairs not covered by the vehicle warranty. Notice: If the wheel(s) of one axle is allowed to[...]

Limited-Slip Rear Axle Vehicles with a limited-slip rear axle can give more traction on snow, mud, ice, sand or gravel. It works like a standard axle most of the time, but when traction is low, this feature allows the drive wheel with the most traction to move the vehicle. All-Wheel Drive (AWD) System With this feature, engine power is sent to all [...]

Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you. These problems can be avoided by braking — if you can stop in t[...]

Of f-Road Recovery The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement. Turn the s[...]

Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle’s three control systems. In the braking skid, the wheels are not rollin[...]

Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: • Drive defensively. • Do not drink and drive. • Reduce headlamp glare by adjusting the inside rearview mirror. • Slow down and keep [...]

Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or flowing water. { CAUTION: Wet brakes can cause crashes. They might not work as well in a quick stop and[...]

Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? • Wiper Blades: In good shape? • Fuel, Engine Oil, Other Fluids: All levels checked? [...]

Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all fluid levels and brakes, tires, cooling system, and transmission. • Going down steep or long hills, shift to a lowe[...]

Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand. Drive w[...]

CAUTION: (Continued) • Open a window about two inches (5 cm) on the side of the vehicle that is away from the wind to bring in fresh air. • Fully open the air outlets on or under the instrument panel. • Adjust the Climate Control system to a setting that circulates the air inside the vehicle and set the fan speed to the highest setting. See C[...]

If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow Slowly and cautiously spin the wheels to free the vehicle when stuck in sand, mud, ice, or snow. See Rocking Your Vehicle to Get It Out on page 4-21 . If the vehicle has a traction system, it can often help to free a stuck vehicle. Refer to the vehicle’s traction system in the Index. If stuck to[...]

Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. Shift back and forth between R (Reverse) and a forward gear, spinning the wheels as little as possible. To prevent transmission wear, wait until the wheels stop spinning before shifting gear[...]

Tire and Loading Information Label A vehicle specific Tire and Loading Information label is attached to the center pillar (B-pillar). With the driver’s door open, you will find the label attached below the door lock post (striker). The tire and loading information label shows the number of occupant seating positions (A), and the maximum vehicle[...]

Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX [...]

Item Description Total A Vehicle Capacity Weight for Example 1 = 1,000 lbs (453 kg) B Subtract Occupant Weight 150 lbs (68 kg) × 2 = 300 lbs (136 kg) C Available Occupant and Cargo Weight = 700 lbs (317 kg) Item Description Total A Vehicle Capacity Weight for Example 2 = 1,000 lbs (453 kg) B Subtract Occupant Weight 150 lbs (68 kg) × 5 = 750 lbs [...]

Item Description Total A Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C Available Cargo Weight = 0 lbs (0 kg) Refer to your vehicle’s tire and loading information label for specific information about your vehicle’s capacity weight and seating positions. The comb[...]

Certification/Tire Label A vehicle specific Certification/Tire label is found on the rear edge of the driver’s door. The label shows the size of your vehicle’s original tires and the inflation pressures needed to obtain the gross weight capacity of your vehicle. This is called Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight[...]

Using heavier suspension components to get added durability might not change your vehicle’s weight ratings. Ask your dealer to help you load your vehicle the right way. Notice : Overloading your vehicle may cause damage. Repairs would not be covered by your warranty. Do not overload your vehicle. If you put things inside your vehicle like suitcas[...]

Recreational Vehicle Towing Recreational vehicle towing means towing the vehicle behind another vehicle – such as behind a motorhome. The two most common types of recreational vehicle towing are known as “dinghy towing” — towing the vehicle with all four wheels on the ground, and “dolly towing” — towing the vehicle with two wheels on [...]

If the suspension remains at a low height, the rear axle load has exceeded GAWR (Gross Axle Weight Rating). When the overload protection mode is activated, the compressor operates for about 30 seconds to one minute without raising the vehicle depending on the amount of overload. This will continue each time the ignition is turned on until the rear [...]

Pulling A Trailer Here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police. • Consider using a sway control. S[...]

Look in the following chart to find the maximum trailer weight for the vehicle. Vehicle Axle Ratio Max. Trailer Wt. *GCWR AWD (4.2 L L6 Engine) 3.73 5,600 lbs (2 540 kg) 10,500 lbs (4 763 kg) AWD (5.3 L V8 Engine) 3.73 6,500 lbs (2 948 kg) 11,500 lbs (5 216 kg) AWD (6.0 L V8 Engine) 4.10 6,500 lbs (2 948 kg) 11,500 lbs (5 216 kg) *The Gross Combin[...]

Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle. If there are a lot of options, equipment, passe[...]

Do not exceed the maximum allowable tongue weight for the vehicle. Choose the shortest hitch extension that will position the hitch ball closest to the vehicle. This will help reduce the effect of trailer tongue weight on the rear axle. After loading the trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. I[...]

If the vehicle has many options and there is a front seat passenger and two rear seat passengers with some luggage and gear in the vehicle as well. 300 lbs (136 kg) could be added to the front axle weight and 400 lbs (181 kg) to the rear axle weight. The vehicle now weighs: Weight is still below 7,200 lbs (3 266 kg) and you might think 700 addition[...]

Weight Distributing Hitches and Weight Carrying Hitches When using a weight-distributing hitch, the hitch must be adjusted so that the distance (A) remains the same both before and after coupling the trailer to the tow vehicle. If pulling a trailer that, when loaded, will weigh more than 4,000 lbs (1 814 kg) be sure to use a properly mounted weight[...]

Driving with a Trailer { CAUTION: When towing a trailer, exhaust gases may collect at the rear of the vehicle and enter if the liftgate, trunk/hatch, or rear-most window is open. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. To maximize safety when towing a trailer: • Ha[...]

Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer. This can help to avoid situations that require heavy braking and sudden turns. Passing More passing distance is needed when towing a trailer. Because the rig is longer, it is necessary to go much farther beyond the passed [...]

Driving On Grades Reduce speed and shift to a lower gear before starting down a long or steep downgrade. If the transmission is not shifted down, the brakes might have to be used so much that they would get hot and no longer work well. Vehicles can tow in D (Drive). Shift the transmission to a lower gear if the transmission shifts too often under h[...]

Leaving After Parking on a Hill 1. Apply and hold the brake pedal while you: • start the engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4. Stop and have someone pick up and store the chocks. Maintenance When Trailer Towing The vehicle needs [...]

The seven-wire harness contains the following trailer circuits: • Yellow: Left Stop/Turn Signal • Dark Green: Right Stop/Turn Signal • Brown: Running Lamps • White: Ground • Light Green: Back-up Lamps • Dark Blue: Electric Brakes • Red: Battery Feed (The chassis wiring ring terminal must be fastened to a stud on the underhood electric[...]

Service ........................................................... .5-3 Accessories and Modifications ......................... .5-3 California Proposition 65 Warning .................... .5-3 California Perchlorate Materials Requirements .... .5-3 Doing Your Own Service Work ........................ .5-4 Adding Equipment to the Outside of the Ve[...]

Tires ............................................................. .5-59 Tire Sidewall Labeling .................................. .5-60 Tire Terminology and Definitions .................... .5-62 Inflation - Tire Pressure ................................ .5-65 High-Speed Operation .................................. .5-66 Tire Pressure Monitor S[...]

Service For service and parts needs, visit your dealer/retailer. Accessories and Modifications When you add non-dealer/non-retailer accessories to your vehicle, they can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems[...]

Doing Your Own Service Work { CAUTION: You can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. • Be sure you have suff icient knowledge, experience, the proper replacement parts, and tools before attempting any vehicle maintenance task. • Be sure to use the proper nuts, bol[...]

Adding Equipment to the Outside of the Vehicle Things added to the outside of the vehicle can affect the airflow around it. This can cause wind noise and can affect fuel economy and windshield washer performance. Check with your dealer/retailer before adding equipment to the outside of the vehicle. Fuel Use of the recommended fuel is an important [...]

California Fuel If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, the vehicle will operate satisfactorily on fuels meeting federal spec[...]

Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the specifications described earlier. However, E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed[...]

Filling the Tank { CAUTION: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling. Do not smoke if you are near fuel or refueling the vehicle. Do not use cellular phones. Keep sparks, flames, a[...]

{ CAUTION: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop. Then unscrew the cap all the way. Be careful not to [...]

Filling a Portable Fuel Container { CAUTION: Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs. To help avoid injury to you and others: • Dispense fuel only into approved containers. • Do not [...]

Hood Release 1. To open the hood, first pull the handle with this symbol on it. It is located inside the vehicle under the instrument panel on the driver’s side. 2. Then go to the front of the vehicle and push the secondary hood latch up and to the right to release it, then lift the hood. Before closing the hood, be sure all the filler caps are[...]

Engine Compartment Overview When you open the hood on the 4.2L L6 engine, here is what you will see: 5-12[...]

A. Engine Air Cleaner/Filter on page 5-24 . B. Engine Coolant Recovery Tank. See Cooling System on page 5-29 . C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-38 . D. Power Steering Fluid Reservoir. See Power Steering Fluid on page 5-37 . E. Automatic Transmission Fluid Dipstick (Out of Vi[...]

When you open the hood on the 5.3L V8 engine, here is what you will see: 5-14[...]

A. Engine Coolant Recovery Tank. See Cooling System on page 5-29 . B. Engine Air Cleaner/Filter on page 5-24 . C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-38 . D. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 5-18 . E. Automatic Transmission Fluid Dipst[...]

When you open the hood on the 6.0L V8 engine, here is what you will see: 5-16[...]

A. Engine Coolant Recovery Tank. See Cooling System on page 5-29 . B. Engine Air Cleaner/Filter on page 5-24 . C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-38 . D. Engine Oil Fill Cap (Under Engine Cover). See “When to Add Engine Oil” under Engine Oil on page 5-18 . E. Engine Oil Di[...]

Engine Oil Checking Engine Oil It is a good idea to check the engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 5-12 for the location of the engine oil dipstick. 1. Turn off th[...]

Notice: Do not add too much oil. If the engine has so much oil that the oil level gets above the cross-hatched area (F) that shows the proper operating range for the L6 engine or above the cross-hatched area for the V8 engine, the engine could be damaged. See Engine Compartment Overview on page 5-12 for the location of the engine oil fill cap. Add[...]

What Kind of Engine Oil to Use Except Vehicles with 6.0L V8 (VIN Code H) Engine Look for three things: • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. • American Petro[...]

For 6.0L V8 (VIN Code H) Engine Vehicles Only Look for three things: • GM4718M This vehicle’s engine requires a special oil meeting GM Standard GM4718M. Oils meeting this standard may be identified as synthetic. However, not all synthetic oils will meet this GM standard. Use only an oil that meets GM Standard GM4718M. Notice: Using oils that d[...]

Cold Temperature Operation Except Vehicles with 6.0L V8 (VIN Code H) Engine If in an area of extreme cold, where the temperature falls below − 20°F ( − 29°C), use either an SAE 5W-30 synthetic oil or an SAE 0W-30 engine oil. Both provide easier cold starting for the engine at extremely low temperatures. Always use an oil that meets the requir[...]

How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a CHANGE ENGINE OIL message being turned on, res[...]

Engine Air Cleaner/Filter See Engine Compartment Overview on page 5-12 for the location of the engine air cleaner/filter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the Maintenance II intervals and replace at the first oil change after each 50,000 mile (80 000 km) interval. See Scheduled Maintenance on page 6[...]

{ CAUTION: Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. If it is not there and the engine backfires, you could be burned. Do not drive with it off, and be careful working on the engine with the air cleaner/fil[...]

How to Check Automatic Transmission Fluid Because this operation can be a little diff icult, you may choose to have this done at the dealer/retailer service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. Notice: Too much or too little fluid can damage your transmiss[...]

Checking the Fluid Level Prepare the vehicle as follows: 1. Park the vehicle on a level place. Keep the engine running. 2. With the parking brake applied, place the shift lever in P (Park). 3. With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then, position the shift leve[...]

Consistency of Readings Always check the fluid level at least twice using the procedure described previously. Consistency (repeatable readings) is important to maintaining proper fluid level. If inconsistent readings persist, contact your dealer/retailer. How to Add Automatic Transmission Fluid Refer to the Maintenance Schedule to determine what [...]

Cooling System The cooling system allows the engine to maintain the correct working temperature. 5.3L V8 Engine shown, 4.2L L6 and 6.0L V8 Engines similar A. Coolant Recovery Tank B. Radiator Pressure Cap C. Engine Fan { CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Kee[...]

Engine Coolant The cooling system in the vehicle is filled with DEX-COOL ® . This coolant is designed to remain in the vehicle for five years or 150,000 miles (240 000 km), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low. If there is a problem with engine overheating, see Engine [...]

Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant recovery tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. If coolant is visible but the coolant level is not at or above the FULL COLD mark, add a 50[...]

How to Add Coolant to the Radiator { CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under press[...]

3. Fill the radiator with the proper DEX-COOL coolant mixture, up to the base of the filler neck. See Engine Coolant on page 5-30 for more information about the proper coolant mixture. 4. Then fill the coolant recovery tank to the FULL COLD mark. 5. Put the cap back on the coolant recovery tank, but leave the radiator pressure cap off. 5-33[...]

6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan. 7. By this time, the coolant level inside the radiator filler neck may be lower. If the level is lower, add more of the proper DEX-COOL coolant mixture through the filler neck until the level reaches the base of the fi[...]

You may decide not to lift the hood when this warning appears, but instead get service help right away. See Roadside Assistance Program on page 7-6 . If you do decide to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If the engine is overheating, both fans should be runni[...]

If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: • Climbs a long hill on a hot day. • Stops after high-speed driving. • Idles for long periods in traff ic. • Tows [...]

Power Steering Fluid See Engine Compartment Overview on page 5-12 for reservoir location. When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and [...]

Windshield Washer Fluid What to Use When the vehicle needs windshield washer fluid, be sure to read the manufacturer’s instructions before use. If the vehicle will be operating in an area where the temperature may fall below freezing, use a fluid that has suff icient protection against freezing. Adding Washer Fluid Open the cap with the washer [...]

Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT-3 brake fluid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down: • The brake fluid level goes down because of normal brake lining wear. When new linings ar[...]

Checking Brake Fluid Check brake fluid by looking at the brake fluid reservoir. See Engine Compartment Overview on page 5-12 . The fluid level should be above MIN. If it is not, have the brake hydraulic system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the level is above the MIN, but not over t[...]

Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly. { CAUTION: The brake wear warning sound means that[...]

Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced — for example, when the brake linings wear down and [...]

Jump Starting If the vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { CAUTION: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you. • They contain gas that can explode or ignite. • T[...]

Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3. Turn off the ignition on both vehicles. Unplug unnecessary accessories plugged into the cigarette light[...]

{ CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know[...]

The remote negative ( − ) terminal is located on the front engine lift bracket for the 4.2L L6 engine, and on the accessory drive bracket for the 5.3L or 6.0L V8 engines. 9. Connect the other end of the negative ( − ) cable to the remote negative ( − ) terminal on the vehicle with the dead battery. 10. Now start the vehicle with the good batt[...]

To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative ( − ) cable from the vehicle that had the dead battery. 2. Disconnect the black negative ( − ) cable from the vehicle with the good battery. 3. Disconnect the red positive (+) cable from the vehicle with the good battery. 4. Disconnect the red[...]

Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle fluid unless you suspect there is a leak or you hear an unusual noise. A fluid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface. For all vehicles, excluding ve[...]

Front Axle When to Check Lubricant It is not necessary to regularly check front axle fluid unless you suspect there is a leak or you hear an unusual noise. A fluid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface. If the level is below the bo[...]

Headlamp Aiming Headlamp aim has been preset at the factory and should need no further adjustment. However, if your vehicle is damaged in a crash, the headlamp aim may be affected. Aim adjustment to the low-beam headlamps may be necessary if oncoming drivers flash their high-beam headlamps at you (for vertical aim). If the headlamps need to be re-[...]

Halogen Bulbs { CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package. Headlamps To replace one of these bulbs: 1. Open the hood. See Hood Release on page 5-11 2. Lift the two headlamp retaining clips to releas[...]

5. Remove the bulb socket that needs to be replaced by turning it counterclockwise. 6. Disconnect the electrical connector from the old bulb. 7. Plug the electrical connector into the new bulb using care not to touch the glass with your fingers. 8. Turn the new bulb clockwise to install it in the socket. 9. Reinstall the bulb covers. 10. Push the [...]

Front Turn Signal, Sidemarker and Parking Lamps To replace one of these bulbs: 1. Follow Steps 1 through 3 under Headlamps on page 5-51 to access the front turn signal, sidemarker or parking lamp. 2. Turn the bulb socket counterclockwise and remove it from the lamp assembly. 3. Holding the socket, pull the old bulb to release it from the socket. 4.[...]

To replace one of these bulbs: 1. Open the liftgate. See Liftgate/Liftglass on page 2-12 . 2. Remove the screws from the taillamp assembly. 3. Pull the taillamp assembly away from the vehicle. 4. Turn the bulb socket counterclockwise to remove it from the taillamp assembly. 5. Holding the socket, pull the bulb to release it from the socket. 6. Push[...]

License Plate Lamp 1. Remove the two screws holding the license plate lamp lens. 2. Pull the lens away from the lamp assembly. 3. Pull the old bulb straight out from the bulb socket. 4. Push the new bulb into the socket until it clicks. 5. Replace the lamp assembly lens and tighten the screws. Replacement Bulbs Exterior Lamp Bulb Number Back-Up Lam[...]

Windshield Replacement Your vehicle is equipped with an acoustic windshield. If you ever have to have your windshield replaced be sure to get an acoustic windshield so you will continue to have the benefits an acoustic windshield can provide. Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See S[...]

4. To install the new wiper insert, slide the insert (D), notched end last, into the end with two blade claws (A). Slide the insert all the way through the blade claws at the opposite end (B). The plastic caps (C) will be forced off as the insert is fully inserted. 5. Be sure that the notches are locked by the bottom claws. Make sure that all other[...]

Backglass Wiper Blade Replacement 1. Lift the wiper blade assembly up and out of the park rest position. 2. Pull the wiper blade assembly away from the backglass. The backglass wiper blade will not lock in a vertical position, so care should be used when pulling it away from the vehicle. 3. Rotate the wiper blade assembly, and pull it off of the wi[...]

Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. { CAUTION: • Poorly maintained and improperly used tires are dangerous.[...]

Low-Profile Performance Tire If your vehicle has P255/50R20 size tires, they are classified as low-profile performance tires. These tires are designed for very responsive driving on wet or dry pavement. You may also notice more road noise with low-profile performance tires and that they tend to wear faster. Notice: If the vehicle has low-profi[...]

(B) TPC Spec (Tire Performance Criteria Specification) : Original equipment tires designed to GM’s specific tire performance criteria have a TPC specification code molded onto the sidewall. GM’s TPC specifications meet or exceed all federal safety guidelines. (C) DOT (Department of Transportation) : The Department of Transportation (DOT) co[...]

(B) Tire Width : The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio : A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 75, as shown in item C of the passenger (P-Metric) tire illustration, it would mean that the tire[...]

Curb Weight : The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings : A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) motor vehicle safety standard[...]

Passenger (P-Metric) Tire : A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure : Vehicle manufacturer’s recommended tire inflation pressure as shown on the tire placard. See Inflation - Tire Pressure on page 5-65 and Loading the Vehicle on page 4-21 . Radial Ply Tire : A pneumatic[...]

Inflation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inflation or over-inflation is all right. It is not. If your tires do not have enough air (under-inflation), you can get the following: • Too much flexing • Too much heat • Tire overloading • Pre[...]

How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are underinflated. Check the tire’s inflation pressure when the tires are cold. Cold means your vehicle has been sitting for at least thr[...]

Example: You will find the maximum load and inflation pressure molded on the tire’s sidewall, in small letters, near the rim flange. It will read something like this: Maximum load 690 kg (1521 lbs) 300 kPa (44 psi) Max. Press. For this example, you would set the inflation pressure for high-speed driving at 36 psi (248 kPa). The inflation pre[...]

Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel eff iciency and tire tread life, and may affec[...]

Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the vehicle’s tires an[...]

TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message is also displayed. The low tire warning [...]

To decrease air-pressure out of a tire you can use the pointed end of the valve cap, a pencil-style air pressure gage, or a key. You have two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the first tire and wheel, or more than five m[...]

Tire Inspection and Rotation We recommend that you regularly inspect your vehicle’s tires, including the spare tire, for signs of wear or damage. See When It Is Time for New Tires on page 5-73 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). See Scheduled Maintenance on page 6-4 . The purpose of a reg[...]

{ CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure [...]

You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric. • The tire has a bump, bulge, or split. • The tire h[...]

GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle. See Tire Inspection and Rotation on page 5-72 for information on pro[...]

Dif ferent Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover. Additionally, if your vehicle has electronic systems such as, antilock br[...]

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual[...]

Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce ti[...]

Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist. Your dealer will know[...]

Used Replacement Wheels { CAUTION: Putting a used wheel on your vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new original equipment wheel. Tire Chains { CAUTION: Do not use tire chains. There is not enough clearance. Tire cha[...]

If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates[...]

Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 3-6 . { CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly in[...]

A. Wheel Block B. Flat Tire The following information explains how to use the jack and change a tire. Removing the Spare Tire and Tools The jacking equipment you will need is stored under the rear seat on the passenger’s side of the vehicle. See Rear Seat Operation on page 1-8 for more information. To release the jack from its holder, turn the kn[...]

The tools you will be using include the wheel wrench (A), wheel blocks (B), extension(s), (socket end) (C), handle (jack end) (D), and jack (E). A. Wheel Wrench B. Hoist Shaft C. Extension D. Retainer E. Spare or Flat Tire (Valve Stem Pointed Up) The following instructions explain how to remove the underbody-mounted spare located underneath your ve[...]

3. Insert the socket end of the extension (C) on a 45 degree angle downward into the hoist drive shaft hole. It is exposed when the rear gate is open and is just above the rear bumper. Be sure the socket end of the extension (C) connects to the hoist shaft (B). 4. Turn the wheel wrench counterclockwise to lower the spare tire. Keep turning the whee[...]

Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 5-82 for more information. 2. Using the wheel wrench, loosen all the wheel nuts by turning the nuts one turn counterclockwise. Do not remove them yet. 3. Turn the jack adjusting knob clockwise by hand to raise the jack lift [...]

{ CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. { CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid persona[...]

7. Remove all the wheel nuts and the flat tire. { CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust CAUTION: (Continued) CAUTION: (Continued) or dirt from places where the wheel attaches to th[...]

9. Place the spare tire on the wheel-mounting surface. { CAUTION: Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle’s wheel could fall off, causing a crash. 10. Put the nuts on by hand. Make sure the cone shaped end is toward the wheel. 11. Tighten each nut by hand until the wheel is held against the hub. If [...]

{ CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wren[...]

Secondary Latch System Your vehicle has an underbody-mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the spare tire from suddenly falling off your vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stored with the valve stem pointing up. See Storing a [...]

2. If visible, first try to tighten the cable by turning the wheel wrench clockwise until you hear two clicks or feel it skip twice. You cannot overtighten the cable. 3. Loosen the cable by turning the wheel wrench counterclockwise three or four turns. 4. Repeat this procedure at least two times. If the spare tire lowers to the ground, continue wi[...]

9. Lower the jack by turning the wheel wrench counterclockwise. Keep lowering the jack until the spare tire slides off the jack or is hanging by the cable. 10. Disconnect the jack handle from the jack and carefully remove the jack. Use one hand to push against the spare while firmly pulling the jack out from under the spare tire with the other han[...]

Storing a Flat or Spare Tire and Tools { CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. { CAUTION: The underbody-mounted spare tire needs to be stored with the valve stem poin[...]

Follow this diagram to store the underbody-mounted flat or spare tire. A. Wheel Wrench B. Hoist Shaft C. Extension D. Retainer E. Spare or Flat Tire (Valve Stem Pointed Up) 1. Put the tire (E) on the ground at the rear of the vehicle. 2. Remove the hubcap, if the vehicle has one, from the flat tire by tapping the backside of the hubcap with the w[...]

7. Make sure the tire is stored securely. Push, pull (A), and then try to turn (B) the tire. If the tire moves, use the wheel wrench and socket end of the extension to tighten the cable. 8. Return the equipment to the proper location in the vehicle as shown next. A. Handle B. Wheel Wrench C. Instruction Label D. Extension(s) E. Knob F. Wheel Blocks[...]

Spare Tire Your vehicle, when new, had a fully-inflated spare tire. A spare tire may lose air over time, so check its inflation pressure regularly. See Inflation - Tire Pressure on page 5-65 and Loading the Vehicle on page 4-21 for information regarding proper tire inflation and loading your vehicle. For instruction on how to remove, install or[...]

When cleaning the vehicle’s interior, only use cleaners specifically designed for the surfaces being cleaned. Permanent damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on glass. Remove any accidental over-spray from other surfaces immediately. To prevent over-spray, apply cleaner directl[...]

Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For any soil, always try to remove it first with plain water or club soda. Before cleaning, gently remove as much of the soil as poss[...]

Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces. Many commercial cleaners and coatings tha[...]

Washing Your Vehicle The best way to preserve the vehicle’s finish is to keep it clean by washing it often. Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle. Check the cleaning product label. If it states that it should not be used on plastic parts, do not use it on the vehicle or damage may occ[...]

Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. Approved cleaning products can be obtained from your dealer/retailer. If the vehicle has a basecoat/clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes[...]

Aluminum Wheels Notice: Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash the vehicle’s chrome with soap and water after exposure. Notice: Using [...]

Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle. Sheet Metal Damage If the vehicle is damaged and requires sheet metal rep[...]

Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle. The VIN also appears on the Certification/Tire and Service Parts labels and the certific[...]

Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/retailer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle’s warranty. Some add-on electrical equipment can keep other components from working as they shoul[...]

Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse w[...]

Fuses Usage 1 Electronically Controlled Air Suspension 2 Passenger Side Headlamp High-Beam Fuses Usage 3 Passenger Side Headlamp Low-Beam 4 Trailer Back-Up 5 Driver Side Headlamp High-Beam 5-108[...]

Fuses Usage 6 Driver Side Headlamp Low-Beam 7 Windshield Wiper 8 Automatic Transfer Case 9 Windshield Washer 10 Powertrain Control Module B 11 Fog Lamps 12 Stoplamp 13 Cigarette Lighter 14 Ignition Coils 15 Transmission Control Module Canister 16 Ignition B 18 Airbag 19 Electric Brake 21 Horn 22 Ignition E 23 Electronic Throttle Control 24 Instrume[...]

J-Case Fuses Usage 35 Blower 36 Driver Side Headlamp 62 Passenger Side Headlamp 65 Vehicle Stability Enhancement System (StabiliTrak ® ) 68 Air Pump Relays Usage 37 Headlamp Wiper 38 Rear Windshield Wiper/Washer 39 Fog Lamps 40 Horn 41 Fuel Pump 42 Windshield Washer 43 High-Beam Headlamp 44 Air Conditioning 46 Headlamp Driver Module 47 Starter 49 [...]

Fuses Usage 01 Passenger Door Control Module 02 Driver Door Control Module 03 Liftgate Module 2 04 Truck Body Controller 3 05 Blank 06 Blank 07 Truck Body Controller 2 08 Power Seats 09 Rear Wiper 10 Driver Door Module 11 Amplifier 12 Passenger Door Module 13 Blank 14 Driver Side Rear Parking Lamps 15 Blank 16 Vehicle Center High-Mounted Stoplamp [...]

Fuses Usage 21 Locks 22 Blank 23 Blank 24 Unlock 25 Ignition 0 26 Overhead Battery/OnStar ® System 27 Rainsense Wipers 28 Sunroof 29 Accessory 30 Parking Lamps 31 Truck Body Controller Accessory 32 Truck Body Controller 5 33 Front Wipers 34 Ignition 3 35 Vehicle Stop 36 Transmission Control Module 37 Heat Ventilation Air Conditioning B Fuses Usage[...]

Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information. Application Capacities English Metric Air Conditioning Refrigerant R134a For the air conditioning system refrigerant charge amount, see the refrigerant caution labe[...]

Application Capacities English Metric Fuel Tank 22.0 gal 83.3 L Transfer Case Lubricant 2.0 qt 1.8 L Transmission Fluid (Drain and Refill) 5.0 qt 4.7 L Wheel Nut Torque 100 lb ft 140 Y All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual. Recheck the fluid level after filling. Engi[...]

Maintenance Schedule ..................................... .6-2 Introduction .................................................. .6-2 Maintenance Requirements ............................. .6-2 Your Vehicle and the Environment ................... .6-2 Using the Maintenance Schedule ..................... .6-2 Scheduled Maintenance ...................[...]

Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended fluids and lubricants as prescribed in this manual are necessary to keep this vehicle in good working condition. Any damage cause[...]

{ CAUTION: Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, see your dealer/retailer to have a qualified technician do the work. See Doing Your[...]

Scheduled Maintenance When the CHANGE ENGINE OIL DIC message displays, service is required for the vehicle. See DIC Warnings and Messages on page 3-45 . Have the vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if driving under the best conditions, the engine oil life system may not indicate that vehic[...]

Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter. See Engine Oil on page 5-18 . Reset oil life system. See Engine Oil Life System on page 5-22 . An Emission Control Service. •• Visually check for any leaks or damage. See footnote (j). •• Inspect engine air cleaner filter. If necessary, replace filte[...]

Additional Required Services The following services should be performed at the first maintenance service ( I or II ) after the indicated miles (kilometers) shown for each item. Additional Required Services Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Inspect f[...]

Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Engine cooling system service (or every five years, whichever occurs first). An Emission Control Service. See footnote (i). • Inspect engine accessory drive belt. An Emissi[...]

(e) Make sure the safety belt reminder light and safety belt assemblies are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also see Checking the Restraint Systems on page 1-66[...]

At Each Fuel Fill It is important to perform these underhood checks at each fuel fill. Engine Oil Level Check Notice: It is important to check the engine oil regularly and keep it at the proper level. Failure to keep the engine oil at the proper level can cause damage to the engine not covered by the vehicle warranty. Check the engine oil level an[...]

At Least Once a Year Starter Switch Check { CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. 2. Firmly apply both the parking brake and the regular brake. See Parking Brake on page 2-27 .[...]

Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position. • The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). • The ignition key should come out only in LOCK/OFF. Contact your dealer/retailer if service is required. Parking Brake[...]

Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine Oil (Except 6.0L V8 Engine) Engine oil which meets Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. [...]

Usage Fluid/Lubricant Front Axle SAE 75W-90 Synthetic Axle Lubricant (Part No. U.S. 89021677, in Canada 89021678) meeting specifications. Rear Axle SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 89021677, in Canada 89021678) meeting GM Specification 9986115. With a complete drain and refill add 5.5 ounces (163 ml) of Limited-Slip Axle Lub[...]

Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer. Part Part Number ACDelco Part Number Automatic Transmission Filter Kit 24208576 24208576 Engine Air Cleaner/Filter 15036141 A2014C Engine Oil Filter 4.2L L6 89017342 PF61 5.3L V8; 6.0L V8 89017524 PF48 Spark Pl[...]

Engine Drive Belt Routing 4.2L L6 Engine 5.3L V8 and 6.0L V8 Engines 6-15[...]

Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 . Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. You should[...]

Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-17[...]

Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-18[...]

Customer Assistance and Information .............. .7-2 Customer Satisfaction Procedure ..................... .7-2 Online Owner Center ..................................... .7-5 Customer Assistance for Text Telephone (TTY) Users ............................... .7-6 Customer Assistance Off ices ........................... .7-6 Roadside Assistance Pr[...]

Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Saab. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concern[...]

STEP THREE: Both Saab and your Saab dealer are committed to making sure you are completely satisfied with your new vehicle. However, if you continue to remain unsatisfied after following the procedure outlined in Steps One and Two, you can file with the Better Business Bureau (BBB) Auto Line Program to enforce any additional rights you may have.[...]

STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps One and Two, General Motors of Canada Limited, on behalf of Saab Automobile, A.B., wants you to be aware of its participation in a no-charge Mediation/Arbitration Program. General Motors of Canada Limit[...]

Online Owner Center Online Owner Center (U.S.) — www.gmownercenter.com/saab Information and services customized for your specific vehicle — all in one convenient place. • Digital owner manual, warranty information, and more • Online service and maintenance records • Find Saab dealers for service nationwide • Exclusive privileges and of[...]

Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Saab has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Saab by dialing: 1-866-612-0380. (TTY users in Canada can dial 1-800-263-3830.) Customer As[...]

Coverage Services are provided up to 4 years/50,000 miles (80 000 km), whichever comes first. In the U.S., anyone driving the vehicle is covered. In Canada, a person driving the vehicle without permission from the owner is not covered. Roadside Assistance is not a part of the New Vehicle Limited Warranty. Saab and General Motors of Canada Limited [...]

Services Not Included in Roadside Assistance • Impound towing caused by violation of any laws. • Legal fines. • Mounting, dismounting or changing of snow tires, chains, or other traction devices. • Towing or services for vehicles driven on a non-public road or highway. Services Specific to Canadian Purchased Vehicles • Fuel delivery: Re[...]

Courtesy Transportation To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for vehicles with the Bumper-to-Bumper (Base Warranty Coverage period in Canada) in both the U.S. and Canada. Several courtesy transportation options are available to assist in reducin[...]

Claim amounts should reflect actual costs and be supported by original receipts. See your dealer for information regarding the allowance amounts for reimbursement of fuel or other transportation costs. Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain[...]

Collision Parts Genuine Saab Collision parts are new parts made with the same materials and construction methods as the parts with which your vehicle was originally built. Genuine Saab Collision parts are your best choice to ensure that your vehicle’s designed appearance, durability and safety are preserved. The use of Genuine Saab parts can help[...]

If a Crash Occurs Here is what to do if you are involved in a crash. • Try to relax and then check to make sure you are all right. If you are uninjured, make sure that no one else in your vehicle, or the other vehicle, is injured. • If there has been an injury, call emergency services for help. Do not leave the scene of a crash until all matter[...]

Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs, Saab recommends that you take an active role in its repair. If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there. Specify to the facility that any required replacement collision parts be original equi[...]

Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, notify Transport Canada immediately, in addition to notifying General Motors of Canada Limited. Call them at 1-800-333-0510 or write to: Transport Canada Road Safety Branch 2780 Sheff ield Road Ottawa, Ontario K1B 3V9 Re[...]

Current and Past Model Order Forms Technical Service Bulletins and Manuals are available for current and past model Saab 9-7x vehicles. To request an order form, please specify year and model name of the vehicle. ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visi[...]

Event Data Recorders This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynami[...]

OnStar ® If your vehicle has OnStar and you subscribe to the OnStar services, please refer to the OnStar Terms and Conditions for information on data collection and use. See also OnStar ® System on page 2-35 in this manual for more information. Navigation System If your vehicle has a navigation system, use of the system may result in the storage [...]

✍ NOTES 7-18[...]

A Accessories and Modifications ............................ 5 - 3 Accessory Power Outlets ................................. 3-18 Adding Equipment to Y our Airbag-Equipped V ehicle ....................................................... 1-65 Additives, Fuel ................................................. 5 - 6 Add-On Electrical Equipment .......[...]

Audio System (cont.) Radio Reception .......................................... 3-98 Rear Seat Audio (RSA) ................................ 3-95 Setting the Clock ......................................... 3-57 Theft-Deterrent Feature ................................ 3-97 XM™ Satellite Radio Antenna System ............ 3-99 Audio System(s) .......[...]

Chains, T ire ................................................... 5-80 Charging System Light .................................... 3-30 Check Engine Lamp .............................................. 3-34 Gages W arning Light ................................... 3-40 Check Gas Cap Light ...................................... 3-41 Checking Things Und[...]

Customer Assistance Information (cont.) Customer Satisfaction Procedure ..................... 7 - 2 Reporting Safety Defects to Saab .................. 7-14 Reporting Safety Defects to the Canadian Government .............................. 7-14 Reporting Safety Defects to the United States Government ......................... 7-13 Roadside Assistan[...]

Electronic Immobilizer P ASS-Key ® III+ ........................................... 2-17 Electronic Immobilizer Operation P ASS-Key ® I I I ............................................. 2-18 Electronically Controlled Air Suspension System ...................................................... 4-28 Engine Air Cleaner/Filter .......................[...]

Fuel (cont.) G a g e ......................................................... 3-41 Gasoline Octane ........................................... 5 - 5 Gasoline Specifications .................................. 5 - 5 Low W arning Light ....................................... 3-41 Fuses Engine Compartment Fuse Block ................. 5-107 Fuses and [...]

Hood Checking Things Under ................................ 5-10 Release ..................................................... 5-11 H o r n ............................................................... 3 - 6 How to Wear Safety Belts Properly ................... 1-15 I Ignition Positions ............................................. 2-20 Infants a[...]

Light (cont.) Security ..................................................... 3-38 Service All-Wheel-Drive ................................ 3-40 StabiliT rak Service ....................................... 3-32 StabiliT rak ® Indicator .................................... 3-33 T ire Pressure .............................................. 3-34 Light[...]

N Navigation System, Privacy .............................. 7-17 Navigation/Radio System, see Navigation Manual ...................................................... 3-74 New V ehicle Break-In ...................................... 2-19 O Odometer ...................................................... 3-26 Odometer , T rip ........................[...]

Power (cont.) Reclining Seatbacks ...................................... 1 - 5 Reduced Engine Light .................................. 3-39 Retained Accessory ..................................... 2-21 S e a t ............................................................ 1 - 2 Steering Fluid ............................................. 5-37 Windows[...]

Restraint System Check Checking the Restraint Systems .................... 1-66 Replacing Restraint System Parts After a Crash .......................................... 1-67 Retained Accessory Power ............................... 2-21 Roadside Assistance Program ....................................... 7 - 6 Rocking Y our V ehicle to Get it Out ..[...]

Shifting Out of Park ........................................ 2-29 Signals, T urn and Lane-Change .......................... 3 - 7 Spare T ire ..................................................... 5-97 Installing .................................................... 5-86 Removing ................................................... 5-83 Storing .....[...]

Tires (cont.) Installing the Spare T ire ................................ 5-86 Pressure Monitor Operation ........................... 5-69 Pressure Monitor System .............................. 5-67 Removing the Flat T ire ................................. 5-86 Removing the Spare T ire and T ools ............... 5-83 Secondary Latch System ........[...]

W W arning Lights, Gages, and Indicators ............... 3-24 W arnings DIC W arnings and Messages ........................ 3-45 Hazard W arning Flashers ............................... 3 - 6 Safety and Symbols ......................................... i i i W asher , Headlamps ........................................ 3-10 Wheels Alignment and T ir[...]