Sanyo HEC-DR7700K manual

CONTENTS PAGE Be sure to read this manual thoroughly in order to ensure proper use. In particular, make certain to read the section " I M P O R T A N T S A F E T Y I N S T R U C T I O N S " . Kee p thi s man ual i n a saf e pla ce so that it ca n be f ound e asil y. INSTRUCTION MANUAL Massage Lounger 9BF-6-P111-336AI-0 0207 HEC-DR7700K HE[...]

2 IMPORTANT SAFETY INSTRUCTIONS 1 All of the following information is important. Be sure to follow the instructions carefully. Wh e n u s i ng a n e l ec t r ic a l ap p li a n ce , ba s i c p r e ca u ti o n s s h ou l d al w a ys b e f o ll o w ed , in c l ud i n g t h e following: Read all instructions before using this appliance. Always unplug [...]

4 3 Be careful not to spill water over the remote control, sensor controller, seat, or foot rest. Otherwise, electric shock, short circuit or fire may occur. Do not suddenly release your hand, while raising the foot rest. Otherwise, an injury may occur. Prior to use, be sure to raise the back pad in order to check that the cover cloth or the cloth [...]

6 5 NAME/FUNCTION OF EACH PART Caster Used when moving the chair. Back rest Back pad Arm rest Head cover Seat Remote control Sensor controller Massaging rollers Cord Power plug Grounding pin Cover A Foot rest slide lever Foot rest Cover B Stand Installation screws (3 screws) Check the accessories at first. SPEED ADJUST buttons Adjusts the speed of [...]

8 7 NAME/FUNCTION OF EACH PART REPEAT! display Turns on during Whole Body Sensor Automatic Courses and Automatic Courses. The ring lights up by pressing the REPEAT! button when you want to repeat your desired massage during the course of massaging. While the degree of stiffness is being measured in a Whole Body Sensor Automatic Course, the result i[...]

10 9 HOW TO INSTALL THE STAND Installation screws 1 Remove the covers on the outer sides of the arm rests. Insert the flathead screwdriver into the holes under the cover and pull toward you. (4 places) 5 Put the cords of the remote control and sensor controller in the cord hook on the back of the body. 2 Secure the stand on the left-hand side of th[...]

12 11 HOW TO USE PREPARATIONS PRIOR TO USE ① ③ Press the OPERATION ON/OFF button. Select a massaging course. (See page 16-24) ② Adjust the angle of back rest and foot rest with the ZERO-G button, RECLINING button and FOOT REST UP and DOWN button. (See page 13-15) 1 Turn on the power. (See page 12) The procedure for use of the massager is expl[...]

14 13 ADJUSTMENT OF CHAIR Before sitting on the massage chair OR (Remote control) (Sensor controller) Raise the back rest, and lower the foot rest by continuously pressing the UP ( ) button. Recline the back rest, and raise the foot rest by continuously pressing the DOWN ( ) button. Do not attempt to recline the back rest deeply at first (until the[...]

16 15 ADJUSTMENT OF CHAIR MASSAGING (WHOLE BODY SENSOR AUTOMATIC COURSES) Ref er to the page 27 and 2 8 re gardi ng t he ma ssagi ng c onten ts o f Who le B ody S enso r Aut omati c Co urses . Cha nge o f co urse duri ng ma ssag ing, or c hange to t he A utoma tic Cours e or the Manu al Co urse, is possi ble. When the button is pressed, the lamp of[...]

18 17 MASSAGING (WHOLE BODY SENSOR AUTOMATIC COURSES) 7 Adjust the strength of massage. (See page 18) ③ Massages according to the stiffness. Adjusts the operation and strength of standard massaging according to the measured degree of stiffness. → Massaging operation and the display of remote control.               ?[...]

20 19 MASSAGING (AUTOMATIC COURSES) ① Measure the position of shoulder. ② Starts the massaging of selected course. Check if the position of shoulder is correct. If not, adjust the position using the POSITION ADJUST button. (See page 20) Each time the UPPER BODY STRENGTH ADJUST button is pressed, the strength of upper body massaging can be adjus[...]

22 21 MASSAGING (MANUAL COURSES) 7 Adjust the height, width, speed, and strength of the massaging rollers. There are some adjustments which are not possible, depending on the type of massage chosen. (See page 23) Adjusting the height of massaging rollers. The approximate position of the massaging rollers is indicated by the lamp on the remote contr[...]

24 23 Several types of desired massage can be selected. It is possible to adjust the movement speed, height position and width of massaging rollers and the strength of massage. (There are some adjustments that are not possible, depending on the kind of massaging. Refer to the table below.) Kinds of massages and adjustments of massaging rollers Kind[...]

26 25 AFTER USE 2 Turn off the POWER. 1 Set the back rest and the foot rest to the starting position. Be sure to check that there are no children, pets, or any obstacles around the massager. MAINTENANCE PROCEDURES Perform daily maintenance by wiping with a soft dry cloth. When they are badly soiled, adopt the following maintenance procedure: ＊ ?[...]

28 〈 WHOLE BODY SENSOR AUTOMATIC COURSE 〉 〈 AUTOMATIC COURSE 〉 Standard massage in FINE Course WAIST Course NECK/SHOULDER Course Spine stretching Shiatsu (Shoulder) Tapping/Kneading (Shoulder, Back, Waist) Tapping/Kneading (Shoulder) Tapping/Kneading (Back) Shiatsu (Waist) Tapping/Kneading (Waist) Sensor massage Tapping (Neck/Shoulder) Tapp[...]

29 TROUBLE-SHOOTING Type of Trouble The operation stops in the middle of massaging in the Whole Body Sensor Automatic Course or Automatic Course Movement of massaging rollers in upward direction, causing operation to stop Check points Countermeasure You feel discomfort during the operation of reclining. (Move toward to the opposite direction tempor[...]