Sears 625.34929 manual

OWNERS MANUAL MODEL NO. 625.349290 CAUTION Read All Safety Guides Before You Start to Install Your Dispensing System SAVE THIS MANUAL -- HOW TO INSTALL- - HOW IT WORKS- - CARE OF- -- SPECIFICATIONS -- -- REPAIR PARTS-- Sears, Roebuck and Coo, Chicago, IL 60684 U.S.A. PRINTED IN U S A[...]

TABLE OF CONTENTS PAGE NO, PAGE NO. Safety Guides ........................................ 3 What Does The Dispensing System Do ....... 3-4 Tools and Materials Needed ......................... 5 Put The System Together ........................ 6 Locating and Solution Injecting ................ 7 Installing ...................................... 8-1[...]

I SAFETY GUnDES A Read all steps, guides and rules carefully before installing and using your new Solution Dispensing System. Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property damage. Reading this book will also help you to get all of the benefits from your dispensing system. A Protect the[...]

WHAT YOUR SOLUT OI water softener, installed on the outlet side of the pressure tank, filters and softens the water If you do not like a remaining chlorine taste, Sears has taste and odor filters to remove it, (2) HYDROGEN SULFIDE WATER -- Many water supplies corrtain hydrogen sulfide (sulphur) Dissolved hydrogen sulfide gas, in underground water, [...]

TREATING WELL WATER PRE-TREATING PRIVATE WELL SYSTEMS HAVING IRON BACTERIA -- Before you put the dispensing system together and install it, chlor- inate the well if it contains more than 10 parts per million (ppm) of bacterial iron. Use the following steps. NOTE: If you don't chlorinate the well, you may have iron in your water for up to 2 mon[...]

PUT YOUR DISPENSING 1, Fasten the solution pump to the base with 4 nylon screws and nuts, as shown 2. Working through the tank fill hole, assemble the Low Level Indicator to the tank as shown, Positon the upper window port so the red indicator is easily seen_ 3. Set the reservoir (tank) into the round indent in the base 4. Cut a 14" length of [...]

WHERE TO LOCATE YOUR Locate the system where... ......a 115 volt, 60 Hz electrical power source is nearby. (See page 11) ...good fresh air flow will cool the solution pump motor and carry away solution fumes. ..... the area is clean and the air is free of dust. A _ .the solution pump and tank are easy to reach for servicing and refilling, BUT OUT O[...]

I BLENDING TANK BLENDING TANK 42 ga! minimum -- separate inlet & outlet -- no air bag or diaphragm Pressure Tank Well I i I ' ,ill i BLENDING TANK 42 gal minimum -- separate inlet & outlet -- no air bag or diaphragm Pressure Tank Well !_ Pump I I Well I II PRESSURE TANK INSTALLED "ON" THE MAIN SUPPLY LINE CAPTIVE AIR PRESSURE[...]

GUBDES TO BNSTALL YOUR S (_) SOLUTION INJECTION INTO THE ALTERNATE DISCHARGE FITTING ON THE WELL PUMP 1. Turn off the electrical power to the well pump and turn off the gas or electric supply to the water heater 2. Open a faucet for a few seconds, to bleed off water pressure, then close 3. Close the shut-off valve on the main water pipe, close to t[...]

I GUIDES TO _) SOLUTION INJECTION BETWEEN THE WELL PUMP AND PRESSURE TANK 1. Turn off the electrical power to the well pump and turn off the gas or electric supply to the water heater, 2. Open a faucet for a few seconds to bleed off water pressure, then close 11. In the same way as in step 9, connect the other end of the tubing to the injection fit[...]

ELECTRICAL WgRRNG GUIDE, € A CAUTION: DO NOT TRY TO DO ANY WIRING IF YOU DO NOT KNOW ELEC- TRICITY. CALL A GOOD ELECTRICIAN A CAUTION: DO NOT DO ANY WIRING ON LIVE CIRCUITS ALWAYS TURN OFF THE ELECTRICAL POWER AT THE SOURCE, NOTE: All wiring must follow local or national electrical codes. 1. Looking at FIG.7and8or9, installand wire in a duplex, 3[...]

I RLL THE TANK WnTH THE SOLUTION DISPENSING SYSTEM RESER- VOIR (TANK) HOLDS 15 GALLONS OF SOLUTION. HOWEVER, ON THE FIRST FILL, ALLOW SOME ROOM IN THE TANK SO THE SOLUTION STRENGTH CAN BE CHANGED IF NEEDED. DE- PENDING ON THE WATER PROBLEM YOU ARE TREATING, FILL THE TANK AND SET THE FEED RATE AS FOLLOWS. IRON AND HYDROGEN SULFIDE TREATMENT -- Remov[...]

I RLL THE TANK WroTH SOLUT 1. Residual still above 0.6, and the feed control knob at 1 or 2-- Use less chlorine in the mixture For example, use 1 gallon of bleach for each 2 gallons of water instead of 1 to 1 2. Residual still below 0,2, and the feed control knob at6or7-- Use more chlorine in the mixture For example, use 2 gallons of bleach for eac[...]

FILL THE TANK WnTH 3. Turn the relief-release valve (clockwise only FIG. 11, page 12) to the open position_ Solution is pumped through the suction tubing, into the pump head, then returned to the tank (takes 3-5 minutes). 4. When you see solution returning to the tank (look through fill hole), close the relief-release valve turning clockwise only_ [...]

KEEP YOUR DaSPENSUNG RESERVOIR (TANK) SOLUTION LEVEL -- After installing the solution dispensing system, check the solution level in the tank daily. Red shows in the Low Level Indicator when about 5 gallons of solution remains. After awhile, you will know about how much solution it uses each day and how often to refill the tank. ALWAYS REFILL BEFOR[...]

I KEEPYOUR DUSPENSnNG LUBRICATION -- At least every 6 months, lubricate the solution pump as follows: 1. Unplug the electrical power cord, 2. Loosen the set screw in the feed control knob and remove the knob and bushing, 3. Remove the pump top cover, 4. Clean all the grease from the moving parts and inspect for wear, damage or corrosion. Replace pa[...]

KEEP YOUR D SPENSING If the dispensing system is exposed to the sun, replace the solution tubing every6 months. Re- place the tubing yearly if the system is installed indoors. CLEAN THE STRAINER-- Before filling the tank with solution, remove the strainer, remove the threaded fitting from the end of the strainer, then clean by forcing water backwar[...]

27 26 25---'- MODEL NO. 625.349290 9 ! 16 RETURN I / m -N m[...]

PARTS LiST MODEL NO. 625.349290 NO. 1 2 4 5 6 7 8 9 10 11 KEY PART NUMBER 818405 818399 818510 8800650 U0812612 818382 811704 811703 8800418 814211 8800702 12 812318 13 816342 14 L98013_-188 15 810036 16 U0816093 8800710 17 818544 18 8800470 DESCRIPTION Float Assembly Pipe, Low Level Indicator Tank Cap Tank, 15 Gal. (incl. Cap, Key No. 3) Bulkhead [...]

S AI S OWNERS MANUAL SERVICE MODEL NO. 625.349290 HOW TO ORDER REPAIR PARTS TELL SEARS YOU WANT IT INSTALLED THEN RELAX (F642-5289) Now that you have purchased your Solution Dispensing System, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co stores Be sure to provide all pe[...]