Sears 831 297241 manual

® 0-8 MPH ° 2.0 HP" STEP INCLINE° PROGRAMMABLE SPEED Model No. 831.297241 Serial No. The serial number can be found in the location shown below. Write the sedal number in the space above. Serial Number _kCAUTION!: Read all safety precautions and instructions in this manual before using this equipment. Keep this manual in a safe place for fu[...]

FULL 90 DAY WARRANTY For 90 days from the date of purchase, when proper assembly and maintenance procedures detailed in the Owner's Manual are followed, SEARS will, free of charge, repair or replace and install a replacement part for any defective part, when this treadmill is used in a normal manner. This warranty does not apply when this trea[...]

® 0-8 MPH • 2.0 HP * STEP INCLINE • PROGRAMMABLE SPEED TABLE OF CONTENTS IMPORTANT SAFETY PRECAUTIONS ......................................................... 4 BEFORE YOU BEGIN ...................................................................... 5 ASSEMBLY .............................................................................. 6 OPE[...]

IMP(: PRE( IS 1, st least 8 feet of clearance behind the tread- mill. Do not place the treadmill near water, out- doors o[ on any surface that blocks an air opening. Do not operate where aerosol prod- ucts ere used or where oxygen Is being admln- Istercd. 2. When connecting the power cord (sea PLUG- GING IN THE POWER CORD on page 7), plug the power[...]

BEFORE .YOUBEGIN_ '_ yOU for selectlqg _e SEARS.UFESTYLEFP 8.0:::_ _ (excluding.holidays); :To help us assist you/please EXP _mill_:TheL FES'r_R8.O'EXP tm_admiil _!_'_ note the product model number and sedal number blends advanced technology with innova_tive :designto before calling. The model number of the treadmill is let you [...]

ASSEMBLY Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY: The 7/32" allen wrench included and your own adjustable wrench _'_. . With the help of a second person, raise the Right Upright (27) and Left Upr[...]

OPERATION AND ADJUSTMENT APPLYING SILICONE LUBRICANT To reduce the friction of the walking belt and minimize wear, a non- oil-, non-petroleum-base silicone lubricant must be applied to the .walking platform before the treadmill is used. Failure to apply lubri- cant will reduce treadmill performance. WITH THE POWER CORD UNPLUGGED, lift each side of [...]

DIAGRAM OF THE CONSOLE The heart of the treadmill is the state-of-the-art programmable console. The console offers both manual and pro- gram operation, and features an array of independent LCD displays to give you continuous exercise feedback. Please read these instructions carefully before operating the console. Note: If there is a sheet of protec[...]

Each program is divided into eight equal time periods, called segments. The speed of the walking belt will change automatically at the beginning of each segment. A speed setting should now be programmed for each of the eight segments, using the eight programmable speed controls on the left side of the console. The control on the far left is for the[...]

TROUBLE-SHOOTING AND STORAGE Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at 1- 800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time. 1. SYMPTOM: THE POWER DOES N[...]

4. SYMPTOM: THE WALKING BELT IS OFF-CENTER OR SLIPS WHEN WALKED ON a. If the walking belt has shifted to the left, first remove the safety key and UNPLUG THE POWER CORD. Using the 3/16" allen wrench, turn the left rear roller adjustment bolt clockwise, and the right bolt counterclockwise, 1/4 of a turn each. Be careful not to overtighten the w[...]

CONDITIONING GUIDELINES Th e following guldellnes Willhelp you to plan y0ur. _ i, :: :_: During the.fi_t fe._._onths of y0_e:<e_c_'se-pr_gram , exemlse program. Remember that proper nutdtion and _ : keep your head.iate.llear the Io_/end_f _,ourrtraining adequate rest are essential for successful results. zone as you exemlse.' After a f[...]

SUGGESTED STRETCHES • The following stretches can provide a gond warm-up or cooFdown, Correct form for each_ stretch is sh-(_vn in the drawings below. Move slowly as you stretch_never'b0unce. TOE TOUC H STRETCH - Stand with your knees bent slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach do[...]

PART LIST--Model No. 831.297241 R1094A Key Part No. No. Qty. Description Key Part No. No. Qty. Description 1 120786 1 Left Handrail 56 106334 2 116926 2 Cable "rie 57 012149 3 111869 8 Cage Nut 58 120909 4 120718 1 Console 59 013547 5 120803 1 Speed Control Knob 60 118202 6 120065 1 Long Wire Harness 61 119919 7 114001 1 Console Plate 62 11040[...]

EXPLODED DRAWING---Model No. 831.297241 R1094A 14 13 9O 76 3 98 18 16 85 30 _ 93 59 82 79 / 80 8 11_ 98 15 20 ' i 81 "17 34 56 = 59 8 3 28 ,93 30 31 6 1_7 35 ,-39 .40 41 15[...]

ORDERING REPLACEMENT PARTS Each TREADMILL has its own MODEL NUMBER. Always mention this MODEL NUMBER when requesting ser- vice or repair parts for your TREADMILL. All parts listed herein can be ordered through SEARS, ROEBUCK AND CO. SERVICE CENTERS and most SEARS RETAIL STORES. If parts you need are not stocked locally, your order will be transmitt[...]