Smeg Genuine Apell Gas Hob AP704S3 manual

Contents 1. INSTRUCTIONS FOR SAFE AND PRO PER USE _______________ 22 2. POSITIONING OF HOB ___________________________________ 24 3. ELECTRICAL CO NNECTION ______________________________ 26 4. GAS CONNE CTION ______________________________________ 27 5. ADAPTATION TO DIFFERENT TYPE S OF GAS _______________ 29 6. FINAL OPERATIONS ___________________[...]

Introduction 1. INSTR UCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTE GRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT I N ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTI ONS THEREIN BEFORE USING THE COOKING H OB. ALSO KEEP THE SERIES OF NOZZLES [...]

Introduction THE IDENTIFICATION PLATE, WITH TECHNICA L DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING M UST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT H AS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING. DO NOT PUT PANS WITH OUT PERFECTLY S[...]

Instructions for the installer 24 2. POSITIONING OF HOB The following oper ation requi res buildi ng an d/or carpentry work so must be carried out by a competent tradesman. Installation can be carrie d out on various materials s uch as masonry, metal, solid wood or plastic lamin ated wood as lo ng as they are heat resistant (T 90°C). Never use sil[...]

Instructions for the installer 25 In case of installation on a ho ll ow compartment with doors, a separatin g panel has to b e placed under the hob. Keep a min imum distance of 10 mm between t he bottom of the unit and t he panel surface. The panel has to be easily removable to allo w access in the event of technical service.[...]

Instructions for the installer 26 3. ELECTRICAL CONNECTION Make sure that the voltage and capacit y of the power line conform to the data shown on the plate l ocated under the c asing. Do not remove this plate for any reason. The plug on the end of the supply cable a nd the wall socket must be the same type and conform to the curr ent electrical sy[...]

Instructions for the installer 27 4. GAS CONNECTION Connection to the gas ma ins may be made with a rigid copper pipe or with a flexible pipe and conforming to the prov isions defined by standar d regulations in force. To facilitate connection, fitting A on the rear of the applianc e may be adjusted latera lly. For this purpose, loosen hexagon n ut[...]

Instructions for the installer 28 4.1 Connection to LPG Use a pressure regulator and make t he connection to the tank accordin g to the provisions of stand ards regulations i n force. Make sure that feed pressure conforms to the levels shown in the ta ble in paragraph “ 5.2 Regulation for LPG ”. 4.2 Ventilation of rooms The hob may be installed[...]

Instructions for the installer 29 5. AD APT A TION T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar. For functioning with other ty pes of gas the no zzles must be replaced and the primary air a[...]

Instructions for the installer 30 5.2 Regulation for LPG Loosen screw A and push support B all the w ay. Use a doub le head wrench to remove nozzle C and assembl e the suitable on e, following the instructions indicated in the referenc e charts, with respect to the type of gas to use. The scr ewing torque of the nozzle shoul d never exceed 3 Nm . R[...]

Instructions for the installer 31 5.3 Regulation for natural gas The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar. To allow the unit to work wit h this t ype of gas, perform the same operations described in paragraph “ 5.2 Regulation fo r LPG ”, but choose the nozzles and regulate the primary ai r for natural gas, a[...]

Instructions for the installer 32 6. FINAL OPERA TIONS Having carried out the ab ove adjustments, reassemble the appli ance following, backwards, the ins tructions in paragraph “ 5.1 Removi ng the hob ”. 6.1 Regulation of minimum for natural gas Replace the c omponents on t he burner and slide the knobs on the gas tap pins. Light the burner and[...]

Instructions for the installer 33 6.3 Arrangement of burners on hob BURNERS 1 Auxiliary 2 Semi-rapid 3 Average rapid 4 Large rapid 5-6 Triple crown 7 Double crown 6.4 Lubrication of gas taps After a while, the gas tap may become hard to turn o r lock. If this happens, it has to be cleaned i nside and re-grease d. This must be done by a qualified te[...]

Insructions for the user 34 7. USING THE HOB Make sure that the flame-baffl e crowns, the caps and the grid h ave been assembled correctly. Grid C (supplied) should be us ed for "woks" (Chinese po ts). Adapter B (supplied) is to be used for small v essels. 7.1 Ignition of the burners with safety device For each knob the corresponding burn[...]

Insructions for the user 7.3 Diameter of containers BURNERS Ø min. e max. (in cm) 1 Auxiliary 7-18 2 Semi-rapid 10-24 12-24 3 Average rapid 14-28 4 Large rapid 22-26 5-6 Triple crown 12-34 7 Double crown 7.4 Using a griddle plate A few precautions are necessary if you wish to use a grid dle plate: • leave a gap of at least 160 mm betwe en the ed[...]

Insructions for the user 36 8. CLEANING AND MAINTENANCE NEVER USE A STEAM JET TO CLEAN THE APPLIANCE. Before any intervention, disconnect the power supply of the device. 8.1 Cleaning Clean the cooking top regul arly every time you use it, obviously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean and preserve the su rf[...]