Smeg PGA95F3 manual

Contents 1. INSTRUCTIONS FOR SAFE AND PROPER USE ________________ 4 2. INSTALLATION OF THE APPLIANCE _________________________ 6 3. GAS CONNECTION ______________________________________ 12 4. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 14 5. FINAL OPERATIONS _____________________________________ 16 6. USE OF THE COOKING HOB _______________[...]

Instructions for the installer 4 1. INSTRUCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN A N ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE C O OKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP THE [...]

Instructions for the installer 5 DO NOT PUT PANS WITHOUT PERFECTLY S MOOTH AND FLAT BOTTOMS ON THE COOKI NG HOB GRIDS. DO NOT USE RECIPIENTS OR G RIDDLE PLATES THAT EXTEND BEYOND THE EXTERNAL PERIMETER OF THE HOB. THE HOB IS TO BE USED BY ADULTS ON LY . DO NOT LET UNSUPERVISED CHILDREN PLAY WITH THE HOB. REPLACED APPLIANCES MUST BE TAKEN TO A SPECI[...]

Instructions for the installer 6 2. INST ALLA TION OF THE APPLIANCE The following operation r equires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). 2.1 Fixi[...]

Instructions for the installer 7 2.2 Attachment to support struct ure, flush-mounting model Create an opening w ith the dimensions shown in the figure in the work surface, observing a minimum distanc e of 50 mm from the rear edge. The lower part of the protective cover must be fully accessible when the appliance is installe d. This appliance can be[...]

Instructions for the installer 8 Overall dimensions: location of gas and electrical connection poi nts (all measures in mm). Caution: surface temperature under neath may exceed 125 degrees C. To avoid a hazard, under-bench access must be restricted. Refer to installation instruction IMPORTANT: when installing the ap pliance above a cupboard, a divi[...]

Instructions for the installer 9 2.3 Clearance above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measureme nt A ) Range hoods and exha ust fans shall be installed in accor dance with the manufacturer’s instructions. Howev er, in no case shall the clearance between the highest part of the hob of the c[...]

Instructions for the installer 10 2 Side clearances – (Measurements B & C) Where B , mea sured from the periphery of the nearest burner to any vertical combu stible surface , is less than 200 mm , the surface shall be protected in accorda nce with Clause 5.12.1.2 to a height C of not less than 150 mm above the hob for th e full dimension (wid[...]

Instructions for the installer 11 2.5 Discharge of combustion products Discharge of combustion pr oducts mu st be guaranteed by means of hoods connected to a natur al draught fl ue with certain efficiency, or by means of forced aspiration. An efficient aspiration system requir es careful planning by a specialist capable of insta lling it, respectin[...]

Instructions for the installer 12 3. GAS CONNECTION This appliance is su itable for installation with Natural Gas or ULPG (propane). R efer to page 12 for the relevant burner press ure and appropriate injector sizes. When the ap pliance is to be connected to Natural Gas then the pressure regulator supp lied must be fitted to the gas inlet. A te st [...]

Instructions for the installer 13 3.1 Electrical connection Make sure that the voltage and capacity of the power line conform to the data shown on the plate locat ed under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the curr ent electrical syst[...]

Instructions for the installer 14 4. AD APT A TION T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenanc e work, detach th e appliance from the electrical socket. The hob of the cooker is ad justed for use wi th either natural gas at a pressure of 1.0 kPa . If used with other types of gas, you have to replace the nozzles, then ad [...]

Instructions for the installer 15 4.2 Burner and nozzle characteristic s table Burner ULPG – 2.75 kPa Nominal gas consumption (MJ/h) Injector (mm) Auxiliary (1) 3.9 0.54 Semi rapid (2) 6.3 0.68 WOK (4) 13.5 1.00 Burner NG – 1.0 kPa Nominal gas consumption (MJ/h) Injector (mm) Auxiliary (1) 3.9 0.90 Semi rapid (2) 7.5 1.20 WOK (4) 15 1.75 4.3 Ar[...]

Instructions for the installer 16 5. FINAL OPERA TIONS Having carried out the abov e adjustments, reassemble the applianc e following, backwards, the i nstructions in paragraph “4.2 Burner and nozzle characteristics table”. After adjustment to a different kind of gas from the one for which the cooker has been tested, replac e the plate inside t[...]

Instructions for the user 6. USE OF THE COOKING HOB 6.1 Lighting the burners Before lighting the hob burners che ck that the flame caps are in th e correct position and that their burner caps are in place, making sure th a t the holes A in the flame caps correspon d to the spark plugs an d thermocouples. Panstand grid B, available upon r equest, is[...]

Instructions for the user 18 6.2 Practical advice for usin g the burners For better use of the burners and lower gas consumption, use covered containers that are proportion al in size to the burner to prevent the flame from licking the sides (see para graph “ 6.3 Diameter of containers ”). When water reaches the boiling point, lower the fl ame [...]

Instructions for the user 7. CLEANING AND MAINTENANCE Before any intervention, disconnect the power supply of the device. 7.1 Cleaning stainless steel To keep stainless steel in good cond ition it should be cleaned regularl y after use. Let it cool first. 7.1.1 Ordinary Daily Cleaning To clean and preserve the stainl ess steel surfaces, always use [...]

Instructions for the user 20 7.3 Preventive maintenance This appliance does not nee d any special maintenance. However, a few simple operations have to be c arried out periodically to prevent malfunctioning: Burners: the burners must be cleaned periodically to en sure correct combustion; make sure that a ll t he openings and flame ports are clean a[...]

[...]

914772758/ C[...]