Smeg PTSA725X3 manual

Table of contents 3 1. Precautions for safety and use _________________________ 4 2. Fitting the appliance in the top _________________________ 5 2.1 Fixing to the supporting structure ________________________________________5 3. Electrical connection ________________________________ 7 3.1 Clearance above and around dom estic appliances ___________[...]

Precautions for Safety and Use 4 1. Precautions f or safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CY CLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT C ONTAINS BEFORE USING THE HOB. ALSO KEEP THE SET OF NOZZLES PROVIDED IN A SAFE PLACE.[...]

Instructions for the Installer 5 2. Fitting the appliance in the top The procedures required below must be carried o ut by a skilled builder and/or joiner. The hob can be installed on vari ous materials, including masonry, metal, solid wood and wood finished with plastic laminates, pr ovided the material is heat-resistant (T 90° C). 2.1 Fixing to [...]

Instructions for the Installer 6 edge of the gasket B . The dimensions in the drawing belo w refer to the hole on the inside edge of the gasket. In case of installation on a hollow compartment with doors, a separating panel has to be placed under the hob. K eep a mini mum distance of 10 mm between the bottom of the unit and the panel surface. The p[...]

Instructions for the Installer 7 3. Electrical connection Check that the power su pply line voltage and size are as speci fied on the nameplate underneath the applian ce's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant re gulat[...]

Instructions for the Installer 8 3.1 Clearance abo ve and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (M easurement A ) Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instruction s. However, in no case shall the cleara nce between the highest part of the hob of the c[...]

Instructions for the Installer 9 2 Side clearances – (Mea surements B & C) Where B , measured from the peri phery of the nearest burner to any vertical combustible surface , is less than 200 mm , the surface sh all be protected in accordance with Clause 5.12.1.2 to a height C of not less than 150 mm above the hob for the full dimension (width[...]

Instructions for the Installer 10 4. GAS CONNECTION This appliance is suitable for installation with Natural Ga s or LPG (propane). Refer to page 12 for the relevant burner pressure and appropriate injector si zes. When the appliance is to be connected to Natural Gas then the pressure regulato r supplied must be fitted to the gas inlet. A test poin[...]

Instructions for the Installer 11 5. Adapting to diff erent types of gas Before carrying out the operations described below, disconnect th e appliance from the electricity supply. The hob of the cooker is adjusted for use with either natur al gas at a pressure of 1.0 kPa . If used with other types of gas, you have to replace the nozzles, the n adju[...]

Instructions for the Installer 12 5.2 Adjusting fo r bottled gas Undo the scre w A and push the support B fully down. Remove the nozzle C with a spanner and fit the suitable one followi ng the instructions in the tables referring to the type of gas to be used. The nozzle must not be tightened with a torque of more than 3 Nm . Return the support B t[...]

Instructions for the Installer 13 5.4 Adjusting the primary air flow Refers to the gap “ X ” in mm. BURNER NG – 1.0 kPa ULPG – 2.75kPa Auxiliary 4.0 10.0 Semi rapid 4.0 10.0 Rapid (3) 4.0 10.0 Rapid (6) 4.0 10.0 Rapid (7) 4.0 10.0 Internal 5.0 8.0 WOK double flame (4-8) External 10.0 13.0 WOK 5.0 12.0 5.5 Reassembling the hob skin Reverse t[...]

Instructions for the Installer 14 5.8 Hob b urner lay out Burner type 1 Auxiliary 2 Semi rapid 3 Rapid 4 WOK Double flame 5 WOK 6 Rapid 7 Rapid 8 WOK Double flame 5.9 Greasing the gas taps Over time, the gas taps may beco me stiff or jam. Clean their insides and change their lubricating grease. This operation must be carried out by a skilled techni[...]

Instructions for the User 15 6. Description of contr ols 6.1 The fr ont panel All the hob's control and monitori ng devices are placed together on the front panel. MODEL 60 CONTROL PANEL 4 Burner Hob MODEL 70 CONTROL PANEL 5 Burner Hob 6 Burner Hob, UR2 at Side 6 Burner Ho b, central UR2 KNOB OPERATING MODE To light the flame, press the knob a[...]

Instructions for the User 16 7. Using the hob Check that the fixing rings, burners, flame diffuser rings and pan stands are fitted correctly. The burner pins A must be fitted into the recesses B in the flame diffuser ring. The holes C in the flame diffuser ring must mate with the ignition plugs and thermocouples D on the hob. 7.1 Lighting b urners [...]

Instructions for the User 17 7.4 P an diameters BURNERS 1. Auxiliary 2. Semi rapid 3. Rapid 4. WOK double flame 5. WOK 6. Rapid 7. Rapid 8. WOK double flame min. and max. Ø (in cm) 7-18 10-24 18-24 20-28 20-28 18-24 18-24 20-28[...]

Instructions for the User 18 8. Cleaning and maintenance Before carrying out any operations, disconnect the ap pliance from the electricity supply. 8.1 Cleaning stainless steel To keep the hob in good condition, it must be cleaned regula rly, after each u se, first allowing it to cool. 8.1.1 Routine daily hob cleaning When cleaning an d caring for [...]