Smeg SRV56413 manual

Contents 1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________ 23 2. POSITIONING OF HOB ___________________________________ 25 3. ELECTRICAL CONNECTION ______________________________ 27 4. GAS CONNECTION ______________________________________ 28 5. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 30 6. FINAL OPERATIONS _______________________[...]

Introduction 1. INSTRUCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN A N ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE C OOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP THE SER IES OF NOZZLES SU[...]

Introduction THE IDENTIFICATION PLATE, W ITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER TH E CASING. THE PLATE ON THE CASING MUST NOT BE R EMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING. DO NOT PUT PANS WITHOUT PERFECTLY S [...]

Instructions for the installer 25 2. POSITIONI NG OF HOB The following operation r equires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). Never use silicone [...]

Instructions for the installer 26 In case of installation on a holl ow compartment with doors, a separating panel has to be pl aced under the h ob. Keep a minimum di stance of 10 mm between t he bottom of the unit and t he panel surfac e. The panel has to be easily removable to allow acces s in the event of technical service. (Only for 90 cm models[...]

Instructions for the installer 27 3. ELECT RICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate locat ed under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the curr ent electrical syst[...]

Instructions for the installer 28 4. GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the prov isions defi ned by standard regulations in force. To facilitate connection, fitting A on the r ear of the appliance may be adjusted laterally. For th is purpose, loosen hexagon nut B[...]

Instructions for the installer 29 4.1 Connection to LPG Use a pressure regul ator and make the connection to the tank according to the provisions of standar d s regulations in force. Make sure that fee d pressure conforms to the lev els shown in the table in paragraph “ 5.2 Regulation for LPG ”. 4.2 Ventilation of rooms The hob may be installed[...]

Instructions for the installer 30 5. AD APT A TION T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been inspected for G20 (2H) natural gas at a pressure of 20 mbar. For functioning with other ty pes of gas the nozzles must be replaced and the prim ary air ad[...]

Instructions for the installer 31 5.2 Regulation for LPG Loosen screw A and push supp ort B all the way. Use a double hea d wrench to remove nozzle C and assemble the suit able one, following the instructions indicated in the reference chart s, with respect to the type of gas to use. The screwing torque of the nozzl e should nev er exceed 3 Nm . Re[...]

Instructions for the installer 32 5.3 Regulation for natural gas The hob has been inspected for G20 (2H) natural gas at a pressure of 20 mbar. To allow the unit to work with this type of gas, perform the same operations describe d in paragraph “5.2 Re gulation for LPG”, but choose the nozzles and regulate the primary air for natural gas, as sho[...]

Instructions for the installer 33 5.5 R egulation of primary air Referred to distance “ X ” in mm. To identify the burners on your hob, refer to the drawing s in point “6.3 Arrangement of burners on hob “ BURNER G20 20 mbar G30/G31 28/37 mbar G110 8 mbar Auxiliary (1) 1.5 1.0 0.5 Semi-rapid (2) 1.5 1.5 0.5 Rapid (3) 1.0 1.5 1.0 Ultra rapid [...]

Instructions for the installer 34 6. FINAL OPERA TIONS Having carried out the abov e adjustments, reassemble t he appliance following, backwards, the instructions in pa ragraph “ 5.1 Removing the hob ”. 6.1 R egulation of minimum for natural gas Replace the compon ents on the burn er and slide the knobs on the gas tap pins. Light the burner and[...]

Instructions for the installer 35 6.3 Arrangement of burners on hob BURNERS 1 Auxiliary 2 Semi-rapid 3 Rapid 4 Ultra rapid 5 Double crown 6 Fish pan 6.4 Lubrication of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned inside and re-gr eased. This must be done by a qualified techn ician.[...]

Instructions for the user 36 7. USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted correctly. In the ultrarapid burner, notch A must be aligned with pin B . Grid C provided is intended for use with woks (Chinese pan s). Adapter D comes only with open grids mo dels and is int ended for use w[...]

Instructions for the user 37 7.2 Practical advice for using the burners For better burner performance an d minimum gas consumption, flat bottomed, even recipie nts must be used, with covers and proportiona l in size to the burn ers (see paragraph “ 7.3 Diameter of containers ”). To avoid overcooking or dam age to the surf ace or to the glass co[...]

Instructions for the user 38 7.5 Electric elements 7.5.1 Turning on electric elements Hobs may be fitted with an electric element of varying diameter. The electric element is controll ed by a switch and is turned on by rotating the appropriate knob to the des ired position. Raised indicators make for easier and clearer readi ng and use of th e cont[...]

Instructions for the user 39 WARNING When switching on the electric element for t he first time, or if the electric element has not been used for a long time, to remo ve any humidity from the insulating material it should be dried out by placin g the electric element on position 1 for 30 minut es. To use correctly remember to: • Switch the electr[...]

Instructions for the user 40 8. CLEANING AND MAINTENANCE Never use a steam jet to clean the appliance. Before any intervention, disconnect the power supply of the device. 8.1 Cleaning Clean the cooking top regularly every time you use it, obviously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean and preserve the su rf[...]

Instructions for the user 41 8.2 Cleaning of cooking hob components Grids, caps, flame cap crowns and burners can be removed for ease of cleaning. Wash them in warm water using a non-abras ive detergent, taking care to remove all tough spots. Before remo unting, allow the componen ts to fully dry out . CAUTION: do not wash these components in a dis[...]