Ir para a página of
Manuais similares
-
Tool Storage
Stanley Black & Decker 36800
23 páginas 10.62 mb -
Pole Saw
Stanley Black & Decker CS25/28
22 páginas 1.95 mb -
Automobile Parts
Stanley Black & Decker TJ10
18 páginas 1.63 mb -
Power Hammer
Stanley Black & Decker DH3500
22 páginas 2.69 mb -
Automobile Parts
Stanley Black & Decker HSX22
26 páginas 2.11 mb -
Chainsaw
Stanley Black & Decker CS05
26 páginas 2.94 mb -
Food Saver
Stanley Black & Decker GT18B02
27 páginas 2.64 mb -
Automobile Parts
Stanley Black & Decker AL35
20 páginas 3.1 mb
Bom manual de uso
As regras impõem ao revendedor a obrigação de fornecer ao comprador o manual com o produto Stanley Black & Decker CR27. A falta de manual ou informações incorretas fornecidas ao consumidor são a base de uma queixa por não conformidade do produto com o contrato. De acordo com a lei, pode anexar o manual em uma outra forma de que em papel, o que é frequentemente utilizado, anexando uma forma gráfica ou manual electrónicoStanley Black & Decker CR27 vídeos instrutivos para os usuários. A condição é uma forma legível e compreensível.
O que é a instrução?
A palavra vem do latim "Instructio" ou instruir. Portanto, no manual Stanley Black & Decker CR27 você pode encontrar uma descrição das fases do processo. O objetivo do manual é instruir, facilitar o arranque, a utilização do equipamento ou a execução de determinadas tarefas. O manual é uma coleção de informações sobre o objeto / serviço, um guia.
Infelizmente, pequenos usuários tomam o tempo para ler o manual Stanley Black & Decker CR27, e um bom manual não só permite conhecer uma série de funcionalidades adicionais do dispositivo, mas evita a formação da maioria das falhas.
Então, o que deve conter o manual perfeito?
Primeiro, o manual Stanley Black & Decker CR27 deve conte:
- dados técnicos do dispositivo Stanley Black & Decker CR27
- nome do fabricante e ano de fabricação do dispositivo Stanley Black & Decker CR27
- instruções de utilização, regulação e manutenção do dispositivo Stanley Black & Decker CR27
- sinais de segurança e certificados que comprovam a conformidade com as normas pertinentes
Por que você não ler manuais?
Normalmente, isso é devido à falta de tempo e à certeza quanto à funcionalidade específica do dispositivo adquirido. Infelizmente, a mesma ligação e o arranque Stanley Black & Decker CR27 não são suficientes. O manual contém uma série de orientações sobre funcionalidades específicas, a segurança, os métodos de manutenção (mesmo sobre produtos que devem ser usados), possíveis defeitos Stanley Black & Decker CR27 e formas de resolver problemas comuns durante o uso. No final, no manual podemos encontrar as coordenadas do serviço Stanley Black & Decker na ausência da eficácia das soluções propostas. Atualmente, muito apreciados são manuais na forma de animações interessantes e vídeos de instrução que de uma forma melhor do que o o folheto falam ao usuário. Este tipo de manual é a chance que o usuário percorrer todo o vídeo instrutivo, sem ignorar especificações e descrições técnicas complicadas Stanley Black & Decker CR27, como para a versão papel.
Por que ler manuais?
Primeiro de tudo, contem a resposta sobre a construção, as possibilidades do dispositivo Stanley Black & Decker CR27, uso dos acessórios individuais e uma gama de informações para desfrutar plenamente todos os recursos e facilidades.
Após a compra bem sucedida de um equipamento / dispositivo, é bom ter um momento para se familiarizar com cada parte do manual Stanley Black & Decker CR27. Atualmente, são cuidadosamente preparados e traduzidos para sejam não só compreensíveis para os usuários, mas para cumprir a sua função básica de informação
Índice do manual
-
Página 1
© 201 1 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 30673 6/2012 V er . 6 S afety , O pera tiOn and M aintenance USer ManUaL CR27 HYDRAULIC CIRCULAR SA W[...]
-
Página 2
[...]
-
Página 3
CR27 User Manual ◄ 3 T ABLE OF CONTENTS SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au - thorized and certied dealer . Please read the following warning. For the nearest au[...]
-
Página 4
4 ► CR27 User Manual SAFETY SYMBOLS Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and signal words, as shown below , are[...]
-
Página 5
CR27 User Manual ◄ 5 SAFETY PRECAUTIONS T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maint[...]
-
Página 6
6 ► CR27 User Manual SAFETY PRECAUTIONS • Ensure that the direction of rotation of the saw blade is as prescribed in this manual. • Cut at the rated operating speeds (gpm). • Operate the saw at “no load” for 30 seconds in a safe position and ensure there is no excessive vi- bration or other defects detected. If considerable vi- bration [...]
-
Página 7
CR27 User Manual ◄ 7 ELECTRICAL HAZARDS When a lifting device contacts an electrical conductor , the truck supporting the device is considered to be ener- gized and contact with the truck must be avoided except when emergency rescue procedures are being carried out. Emergency rescue should only be attempted by properly trained personnel familiar [...]
-
Página 8
ELECTRICAL HAZARDS 8 ► CR27 User Manual T able 1. Minimum approach distances from energized conductors for qualied line-clearance arborists and qualied line-clearance arborist trainees. Nominal V oltage kV phase-to-phase Includes 1910.269 elevation factor , sea level to 5000 ft 1 ) Includes 1910.269 elevation factor , 5001–10,000 ft 1 ) I[...]
-
Página 9
ELECTRICAL HAZARDS CR27 User Manual ◄ 9 The tie-in position should be above the work area and located in such a way that a slip would swing the arborist away from any energized electrical conductors or other identied hazard. While climbing, the arborist should climb on the side of the tree that is away from energized electrical conduc- tors as[...]
-
Página 10
10 ► CR27 User Manual T OOL STICKERS & T AGS Fa ilure to use hydraulic hose labeled and certified as non-conductive when using hydraulic tool so n or near electric lines ma yr esul ti n deat ho r Fo rp roper and safe operatio nr ead owner sm anual and mw ke sure that you have been properly trained in correct procedures require df or work seri[...]
-
Página 11
CR27 User Manual ◄ 1 1 HOSE TYPES The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of t[...]
-
Página 12
12 ► CR27 User Manual HOSE RECOMMENDA TIONS Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECT[...]
-
Página 13
CR27 User Manual ◄ 13 HTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limi[...]
-
Página 14
14 ► CR27 User Manual OPERA TION PREOPERA TION PROCEDURES PREP ARA TION FOR INITIAL USE Each unit as shipped has no special unpacking or as- sembly requirements prior to usage. Inspection to as- sure the unit was not damaged in shipping and does not contain packing debris is all that is required. After instal- lation of a saw blade a unit may be [...]
-
Página 15
CR27 User Manual ◄ 15 OPERA TION 13 OPERA TION BLADE INST ALLA TION 1. Handle the saw blade with care. The cutting edges are sharp and careless handling could result in injury . 2. Install the blade over the motor shaft and onto the fi xed collar so that the points of the teeth on the blade are facing clockwise as viewed from the front of the mo[...]
-
Página 16
16 ► CR27 User Manual OPERA TION 4. In sawing limbs which have a tendency to split or tear when making a single saw ush cut, Figure 4, it is advisable to make more than one cut. The rst cut is made a few inches from the point of the ush cut removing the weight of the limb being trimmed out and leaving a short stub. The stub is then us[...]
-
Página 17
CR27 User Manual ◄ 17 OPERA TION AFTER OPERA TION 1. Wipe the saw thoroughly with a clean dry or slightly oiled cloth. 2. Clean tree pitch and residue from the blade. Handle the blade with care to avoid getting cut by the sharp teeth. 3. Check all fasteners for tightness. 4. When the saw is not in use, store horizontally in a clean, dry space and[...]
-
Página 18
18 ► CR27 User Manual OPERA TION Figure 8. Setting Cutter T ooth Angle COLD WEA THER OPERA TION If the saw is to be used during cold weather , preheat the hydraulic uid at low engine speed. When using the normally recommended uids, uid temperature should be at or above 50 °F/10 °C (400 ssu/82 centistokes) be- fore use.[...]
-
Página 19
CR27 User Manual ◄ 19 T OOL PROTECTION & CARE • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system. • Always[...]
-
Página 20
20 ► CR27 User Manual TROUBLESHOOTING If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the saw , always make sure the hydraulic power source is supplying the correct hydraulic ow and pressure to the saw as listed in the table. Use a owmeter kno[...]
-
Página 21
CR27 User Manual ◄ 21 SPECIFICA TIONS Capacity............................................................................................................................9 in. Diameter/23 cm Blade Pressure Range ................................................................................................................ 1000–2000 psi/70–14[...]
-
Página 22
22 ► CR27 User Manual CR27 P ARTS ILLUSTRA TION[...]
-
Página 23
CR27 User Manual ◄ 23 CR27 P ARTS LIST ITEM P ART NO. QTY DESCRIPTION 1 00042 2 OIL TUBE ASSY 2 24829 1 OUTER TUBE ASSY 3 18089 6 CAPSCREW , BUTTONHEAD, 1/4-20 × 3/8 4 00227 1 FIXED COLLAR 5 00103 1 RET AINING RING 6 07407 2 CAPSCREW , HEX SOCKET HEAD, 10- 32 × 3/4 7 001 18 1 RET AINING RING 8 00008 1 RET AINING RING 9 00007 1 BALL BEARING 10 2[...]
-
Página 24
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulic.com IMPORT ANT T o ll out a Product Warranty Recording form, and for information on your warranty , visit Stanleyhydraulic.com and select the W arranty tab. ( NOTE: T he warranty recording form must be submitted t[...]