Supermicro SuperServer 7048R-C1R4+ manual

® S UPER S ER VER ® 7048R-C1R T4+ 7048R-C1R4+ S UPER USER’S MANUAL 1.0[...]

The information in this User ’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: F[...]

iii Preface Preface About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SuperServer 7048R- C1RT4+/7048R-C1R4+. Installation and maintainance should be performed by experienced technicians only . The SuperServer 7048R-C1RT4+/7048R-C1R4+ is a high[...]

S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual iv Chapter 5: Advanced Serverboard Setup Chapter 5 provides detailed information on the X10DRC-T4+/LN4+ serverboard, including the locations and functions of connections, headers and jumpers. Refer to this chapter when adding or removing processors or main memory and when reconguring the[...]

Notes Preface v[...]

vi T able of Contents Chapter 1 Introduction 1-1 Overview ......................................................................................................... 1-1 1-2 Serverboard Features ..................................................................................... 1-2 Processors ........................................................[...]

vii Power .............................................................................................................. 3-1 Reset ............................................................................................................... 3-1 3-3 Control Panel LEDs ................................................................................[...]

viii Memory Support .............................................................................................. 5-9 Processor & Memory Module Population Conguration ............................ 5-9 5-6 Serverboard Details ....................................................................................... 5-1 1 Serverboard Quick Refere[...]

Chapter 1 Introduction 1-1 Overview The SuperServer 7048R-C1RT4+/7048R-C1R4+ is a high-end server comprised of two main subsystems: the SC745TQ-R1K03B/SC745TQ-R920B 4U server chassis and the X10DRC-T4+/LN4+ dual processor serverboard. Please refer to our web site for information on operating systems that have been certied for use with the system[...]

1-2 S UPER S ERVER 7048R-C1R T/7048R-C1R User's Manual 1-2 Serverboard Features The SuperServer 7048R-C1RT4+/7048R-C1R4+ is built around the X10DRC-T4+/ LN4+, a dual processor serverboard based on the Intel C612 chipset. Below are the main features of the X10DRC-T4+/LN4+. (See Figure 1-1 for a block diagram of the chipset). Processors The X10D[...]

1-3 Chapter 1: Introduction Rear I/O Ports The I/O ports include two COM ports (one Fast UART 16550 external serial port, one serial port header), two VGA ports (1x rear , 1x internal), a dedicated IPMI LAN port and seven USB ports (2x rear , 4x header , 1x type A). It also offers four LAN ports: • X10DRC-LN4+ has Gigabit ports. • X10DRC-[...]

1-4 S UPER S ERVER 7048R-C1R T/7048R-C1R User's Manual Figure 1-1. Chipset Block Diagram Note: This is a general block diagram. Please see Chapter 5 for details. P0 P0 P1 P1 D D E E E F F F G G G H H H CPU 1 CPU 0 PCI-E x16 SLOT 3 PCI-E SATA # 1 SATA # 2 DDR4 DIM M SATA # 3 SATA # 4 SATA # 5 SATA # 6 USB 3.0 SATA DDR4 DIM M #3 #2 #1 DDR4 DIM M[...]

1-5 Chapter 1: Introduction 1-4 Contacting Supermicro Headquarters Address: Super Micro Computer , Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (T echnical Support) Website: www .supermicro.com Europe Address: Super Micro Comp[...]

1-6 S UPER S ERVER 7048R-C1R T/7048R-C1R User's Manual Notes[...]

Chapter 2: Server Installation 2-1 Chapter 2 Server Installation 2-1 Overview This chapter provides a quick setup checklist to get your SuperServer 7048R- C1RT4+/7048R-C1R4+ up and running. Following these steps in the order given should enable you to have the system operational within a minimum amount of time. This quick setup assumes that your sy[...]

2-2 S UPER S ERVER 7048R-C 1R T4+/7048R-C1R4+ User's Manual • This product is not suitable for use with visual display work place devices acccording to §2 of the the German Ordinance for Work with V isual Display Units. 2-4 W arnings and Precautions Rack Precautions • Ensure that the leveling jacks on the bottom of the rack are full[...]

Chapter 2: Server Installation 2-3 Rack Mounting Considerations Ambient Operating T emperature If installed in a closed or multi-unit rack assembly , the ambient operating tempera - ture of the rack environment may be greater than the ambient temperature of the room. Therefore, consideration should be given to installing the equipment in an environ[...]

2-4 S UPER S ERVER 7048R-C 1R T4+/7048R-C1R4+ User's Manual 2-5 Installing the System into a Rack This section provides information on installing the system into a rack unit. Rack installation requires the use of the optional rackmount kit. If the system has already been mounted into a rack or if you are using it as a tower , you can skip ahea[...]

Chapter 2: Server Installation 2-5 Installing the Chassis Rails Y ou will need to remove the top cover and the feet to add rack rails to the chassis. First, remove the top and right covers (top and left covers when standing as a tower chassis) by rst removing the screws that secure them to the chassis. Depress the button on the top (side if towe[...]

2-6 S UPER S ERVER 7048R-C 1R T4+/7048R-C1R4+ User's Manual Installing the Rack Rails Determine where you want to place the SuperServer 7048R-C1RT4+/7048R-C1R4+ in the rack. (See Rack and Server Precautions in Section 2-3. ) Position the xed rack rail/sliding rail guide assemblies at the desired location in the rack, keeping the sliding rai[...]

Chapter 2: Server Installation 2-7 Figure 2-4. Installing the Server into a Rack Installing the Server into the Rack Y ou should now have rails attached to both the chassis and the rack unit. The next step is to install the server into the rack. Y ou should have two brackets in the rack mount kit. Install these rst keeping in mind that they are [...]

2-8 S UPER S ERVER 7048R-C 1R T4+/7048R-C1R4+ User's Manual Notes[...]

Chapter 3: System Interface 3-1 Chapter 3 System Interface 3-1 Overview The control panel on the 7048R-C1RT4+/7048R-C1R4+ has several LEDs and two buttons. There are also two LEDs on each hard drive carrier . These LEDs keep you constantly informed of the overall status of the system and the activity and health of specic components. 3-2 Control [...]

3-2 S UPER S ERVER 7048R-C 1R T4+/7048R-C1R4+ User's Manual 3-3 Control Panel LEDs The control panel located on the front of the SC745 chassis has six LEDs that provide you with critical information related to different parts of the system. This section explains what each LED indicates when illuminated and any corrective ac - tion you may need[...]

Chapter 3: System Interface 3-3 Information LED This LED will be solid blue when the UID function has been activated. When this LED ashes red, it indicates a fan failure. When red continuously it indicates an overheat condition, which may be caused by cables obstructing the airow in the system or the ambient room temperature being too warm. C[...]

3-4 S UPER S ERVER 7048R-C 1R T4+/7048R-C1R4+ User's Manual Notes[...]

4-1 Chapter 4: W arning Statements for AC Systems Chapter 4 Standardized W arning Statements for AC Systems 4-1 About Standardized W arning Statements The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury . Should you have questions or experience difficulty , cont[...]

4-2 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual W arnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr . Sie benden sich in einer Situation, die zu V erletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen V erfahren zur V orbeugung vor Unf?[...]

4-3 W arning Statements for AC Systems 안전을 위한 주의사항 경고! 이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수 있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와 관련된 위험요소들을 확인하시고 사전에 사고[...]

4-4 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual Installation Instructions W arning! Read the installation instructions before connecting the system to the power source. W arnung V or dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen. ¡Advertencia! Lea las instrucciones de instalación antes de conect[...]

4-5 Chapter 4: W arning Statements for AC Systems Circuit Breaker W arning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 250 V , 20 A.. サー キ ッ ト ・ ブ レ ーカー こ の 製品は 、 短絡 （過電流 ） 保護装?[...]

4-6 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual Power Disconnection W arning 電源切断の警告 システムコン ポ ー ネン トの 取り付 け また は 取り外しの た め に 、 シャーシ ー 内 部 にア クセス する に は 、 シ ステムの 電 源 はす べ てのソースから切 断され 、 ?[...]

4-7 Chapter 4: W arning Statements for AC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema. Attention Le système doit être débranché de [...]

4-8 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual Equipment Installation 機器の設置 ト レ ー ニ ン グを受け認 定さ れた人だけが こ の 装 置の 設 置、 交 換、 ま たはサー ビ スを許可 されています 。 W arning! Only trained and qualied personnel should be allowed to install, replace, o[...]

4-9 Chapter 4: W arning Statements for AC Systems ア ク セ ス制限区域 こ の ユニ ッ ト は、 ア ク セ ス制限区域 に 設置 さ れ る こ と を 想定 し て い ま す 。 ア ク セ ス制限区域 は 、 特別な ツ ール 、 鍵 と 錠前、 その 他の セキ ュ リ テ ィ の手段 を用 い て の み[...]

4-10 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual Battery Handling W arning! There is the danger of explosion if the battery is replaced incorrectly . Replace the battery only with the same or equivalent type recommended by the manufacturer . Dispose of used batteries according to the manufacturer's instructions. תלבגומ ה?[...]

4-1 1 Chapter 4: W arning Statements for AC Systems W arnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr . Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers. Attention Danger d'explosion si la pile n'es[...]

4-12 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual W arnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müssen alle V erbindungen entfernt werden. ¡Advertencia! Puede que esta unidad tenga más de una conexión para fuentes de alimentación. Para cortar por compl[...]

4-13 Chapter 4: W arning Statements for AC Systems Backplane V oltage バッ ク プレ ーン の 電 圧 シ ス テ ムの稼 働中 は危険な電 圧 ま たは電力 が、 バ ッ ク プ レ ー ン上に かか っ てい ま す 。 修 理 する 際 に は 注 意く だ さい 。 警告 当系统正在进行时，背板上有很危?[...]

4-14 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual Comply with Local and National Electrical Codes W arning! Installation of the equipment must comply with local and national electrical codes. 地方お よ び国の電気規格 に 準拠 機器の取 り 付け はそ の地方お よ び国の電気規 格に 準拠す る 必要が[...]

4-15 Chapter 4: W arning Statements for AC Systems Product Disposal W arning! Ultimate disposal of this product should be handled according to all national laws and regulations. יצראה למשחה יקוח םואית !הרהזא תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תביי ח דויצה . ?[...]

4-16 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual W aarschuwing De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen. ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. Attention La mise au rebut ou le[...]

4-17 Chapter 4: W arning Statements for AC Systems W arnung Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halten Sie Finger , Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses entfernt. ¡Advertencia! Los ventiladores podran dar vuelta cuando usted quite ell montaje del ve[...]

4-18 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual W arning! When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using any other cables and adaptors could cause a malfunction or a re. Electrical Appliance and Material Safety Law prohibits the use of UL or CSA -certied cable[...]

4-19 Chapter 4: W arning Statements for AC Systems Attention Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné. L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit l'util[...]

4-20 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual Notes[...]

Chapter 5: Advanced Serverboard Setup 5-1 Chapter 5 Advanced Serverboard Setup Thi s ch apter c over s t he ste ps re quir ed to i nst all p ro ce ss or s and h eat sin ks to th e X10DRC-T4+/LN4+ ser verbo ard , co nne ct t he da ta an d po wer c abl es an d ins ta ll add - o n c ard s. A ll se r ver b oar d jum per s an d co nn ec tio ns ar e de s[...]

5-2 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual 5-2 Processor and Heatsink Installation Notes: • Always remove the power cord before adding, removing or changing a CPU. • When receiving a serverboard without a processor pre-installed, make sure that the plastic CPU socket cap is in place and none of the socket pins are bent; otherw[...]

Chapter 5: Advanced Serverboard Setup 5-3 3. With t he se c ond l ever f ully retr ac ted, g ent ly pu sh dow n on the " O pen 1st " lever to l oo sen t he loa d plate. L if t t he lo ad pl ate wi th your nge rs to op en it co mpl etel y . 4. Pop the pl ast ic c ap m ar ked " War nin g" ou t of th e loa d plate. 5. Holding th[...]

5-4 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual 8. Make sure the locking mechanism on the "Close 1st" lever catches the lip of the load plate. Close and lock the "Close 1st" lever . Push down and lock the lever labeled "Open 1st" OPEN 1st OPEN 1st Push down and lock the lever labeled "Close 1st". 9. Cl[...]

Chapter 5: Advanced Serverboard Setup 5-5 Installing a Passive CPU Heatsink 1. Do not apply any thermal grease to the heatsink or the CPU die; the required amount has already been applied. 2. Place the heatsink on top of the CPU so that the four mounting holes are aligned with those on the Serverboard's and the Heatsink Bracket underneath. 3. [...]

5-6 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual 5-3 Connecting Cables Now that the processors are installed, the next step is to connect the cables to the serverboard. These include the data (ribbon) cables for the peripherals and control panel and the power cables. Connecting Data Cables The cables used to transfer data from the peripheral [...]

Chapter 5: Advanced Serverboard Setup 5-7 5-4 I/O Ports Figure 5-2 shows the I/O ports on the rear of the system. Figure 5-2. Rear Panel I/O Ports LAN Ports For the 7048R-C1RT4+ using the X10DRC-T4+ serverboard, the LAN ports of fer 10GBase-T . For 7048R-C1R4+ using the X10DRC-LN4+, the LAN ports provide 1Gb speed. ) Rear I/O Ports 1. COM Port 1 2.[...]

5-8 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual 5-5 Installing Memory Note: Check the Supermicro web site for recommended memory modules. CAU T I O N Exe rc ise ex tr eme c a re wh en in sta lli ng or r emov ing D IM M m odu les to prevent a ny pos si ble d amag e. Installing DIMMs 1. Insert the desired number of DIMMs into the memory slots,[...]

Chapter 5: Advanced Serverboard Setup 5-9 Memory Support The server features 24 DIMM slots that can support up to 1536GB of Load Reduction (LRDIMM) or up to 768GB of Registered (RDIMM)/Non-volatile (NV - DIMM) ECC DDR4-2133/1866/1600/1333 SDRAM or LRDIMM type memory . For the latest memory updates, please refer to our website at http://www .supermi[...]

5-10 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual Caution: For the memory to work properly , install DIMMs of the same type and speed. Mixing of DIMMs of different types or speeds is not allowed. Populating DDR4 Memory Modules INTEL CONFIDENT IAL Intel and the Intel logo are trademarks or registered trademarks of Intel Corporation or its subs[...]

Chapter 5: Advanced Serverboard Setup 5-1 1 Figure 5-4. X10DRC-T4+/LN4+ Layout 5-6 Serverboard Details IPMI CODE SAS CODE SAN MAC T-SGPIO1 T-SGPIO2 JD1 JS39 LEDS6 LEDS5 LEDM1 LE2 LE1 F ANB F ANA F AN4 F AN3 F AN2 F AN1 F AN5 F AN6 JBT1 JIPMB1 SP1 JPS7 JPG1 JPLAN1 JPLAN2 JWD1 JPME2 JI2C2 JVRM1 JPB1 JTPM1 JSD2 JSD1 JS1 JPP0 JPP1 JPWR2 JPWR1 J24 JPI2C[...]

5-12 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual Serverboard Quick Reference Jumpers Jumper Description Default Setting JBT1 Clear CMOS See Section 5-8 JI2C1/JI2C2 SMB to PCI-E Slots Pins 2-3 (Disabled) JPB1 BMC Enable Pins 1-2 (Enabled) JPG1 VGA Enable Pins 1-2 (Enabled) JPLAN1 LAN1/2 Enable Pins 1-2 (Enabled) JPLAN2 LAN3/4 Enable Pins 1-2 [...]

Chapter 5: Advanced Serverboard Setup 5-13 W arning : T o avoid damaging the power supply or the serverboard, be sure to use a power supply that contains a 24-pin and two 8-pin power connectors. Be sure to connect the power supply to the 24-pin power connector (J24), and two 8-pin power connectors (JPWR1, JPWR2) on the serverboard. Failure in doing[...]

5-14 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual 5-7 Connector Denitions Power Connectors A 24-pin main power supply connector (J24), and two 8-pin CPU power connectors (JPWR1/JPWR2) are located on the serverboard. These power connectors meet the SSI EPS 12V specification and must be connected to your power supply to provide adequate powe[...]

Chapter 5: Advanced Serverboard Setup 5-15 Po we r Button OH/Fan Fail/ PWR Fail LED) 1 NIC1 Link LED Rese t Butto n 2 Po we r Fail LED HDD LED FP PWRLED Reset PWR 3.3 V UID Switch UID LED Ground Ground 19 20 3.3V X Ground NMI X NIC2 Link LED NIC2 Activity LED NIC1 Activity LED Front Control Panel JF1 contains header pins for buttons and indicators [...]

5-16 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual Power Fail LED The Power Fail LED connection is located on pins 5 and 6 of JF1. Refer to the table on the right for pin denitions. Overheat (OH)/Fan Fail/PWR Fail/ UID LED Connect an LED cable to pins 7 and 8 of Front Control Panel to use the Overheat/Fan Fail/Power Fail and UID LED connect[...]

Chapter 5: Advanced Serverboard Setup 5-17 Power LED The Power LED connection is located on pins 15 and 16 of JF1. Refer to the table on the right for pin denitions. NMI Button The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin denitions. NMI Button Pin Denitions (JF1) Pin#[...]

5-18 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual GLAN/10G-LAN (TLAN) Ports & IPMI_LAN Port Four Ethernet ports (LAN1/2, LAN3/4) are located on the I/O backplane on the serverboard. These Ethernet ports support Gigabit LANs on the X10DRC-T4+ and support 10G-LANs on the X10DRC-LN4+. In addition, an IPMI_LAN, located above USB 0/1 ports, ca[...]

Chapter 5: Advanced Serverboard Setup 5-19 Chassis Intrusion A Chassis Intrusion header is located at JL1. Attach an appropriate cable from the chassis signal an intrusion when the chassis is opened. Chassis Intrusion Pin Denitions Pin# Denition 1 Intrusion Input 2 Ground Fan Header Pin Denitions Pin# Denition 1 Ground 2 +12V 3 T achome[...]

5-20 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual TPM Header/Port 80 A T rusted Platform Module/Port 80 header is located at JTPM1 to provide TPM support and Port 80 connection. Use this header to enhance system performance and data security . See the table on the right for pin denitions. TPM/Port 80 Header Pin Denitions Pin # Deniti[...]

Chapter 5: Advanced Serverboard Setup 5-21 T -SGPIO1/2 & S-SGPIO1 Headers Three SGPIO (Serial Link Gen - eral Purpose Input/Output) headers are located on the serverboard. T - SGPIO1/2 support onboard I-SA T A connections from the Intel PCH, and S-SGPIO1 supports onboard S-SA T A connections from the Intel SCU. See the table on the right for pi[...]

5-22 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual 5-8 Jumper Settings Explanation of Jumpers T o modify the operation of the serverboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector . Pin 1 is identified with a square solder pad on the printed circuit [...]

Chapter 5: Advanced Serverboard Setup 5-23 VGA Enable/Disable JPG1 allows you to enable or disable the onboard VGA port. The default position is on pins 1 and 2 to enable VGA. See the table on the right for jumper settings. VGA Enable/Disable Jumper Settings Jumper Setting Defn Pins 1-2 Enabled Pins 2-3 Disabled ME Manufacturing Mode Select Close p[...]

5-24 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual 5-9 Onboard Indicators I 2 C Bus to PCI-Exp. Slots Use Jumpers JI 2 C1 and JI 2 C2 to con - nect the System Management Bus (I 2 C) to PCI-Express slots to improve PCI performance. These two jumpers are to be set at the same time. The default setting is on pins 1-2 to enable the connections. Se[...]

Chapter 5: Advanced Serverboard Setup 5-25 Onboard PWR LED Indicator LED States Color/State Denition Off System Power Off Green: On System Power On Onboard Power LED An onboard power LED is located at LE2 on the serverboard. When this LED is on, the system is on. See the table at right for more information. BMC Heartbeat LED A BM C He ar t be at[...]

5-26 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual SA T A Port Pin Denitions P i n # D e n i t i o n 1 Ground 2 TXP 3 TXN 4 Ground 5 RXN 6 RXP 7 Ground Note: For more information on SA T A HostRAID conguration, refer to the Intel SA T A HostRAID User"s Guide posted on our website @ http://www .supermicro.com. SA T A 3.0 Ports T e[...]

Chapter 5: Advanced Serverboard Setup 5-27 5-1 1 Installing Software The Supermicro ftp site contains drivers and utilities for your system at ftp://ftp. supermicro.com . Some of these must be installed, such as the chipset driver . After accessing the ftp site, go into the CDR_Images directory and locate the ISO le for your serverboard. Downloa[...]

5-28 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual SuperDoctor® 5 The Supermicro SuperDoctor 5 is a program that functions in a command-line or web-based interface in Windows and Linux operating systems. The program monitors system health information such as CPU temperature, system voltages, system power consumption, fan speed, and provides a[...]

Chapter 5: Advanced Serverboard Setup 5-29 5-12 Onboard Battery Please handle used batteries carefully . Do not damage the battery in any way; a damaged battery may release hazardous materials into the environment. Do not discard a used battery in the garbage or a public landll. Please comply with the regulations set up by your local hazardous w[...]

5-30 S UPER S E RVER 7048R-C1R(T)4+ User 's Manual Notes[...]

Chapter 6: Advanced Chassis Setup 6-1 Chapter 6 Advanced Chassis Setup This chapter covers the steps required to install components and perform simple maintenance on the SC745TQ-R920B chassis. Following the component installation steps in the order given will eliminate most common problems. If some steps are unnecessary , skip ahead to the step tha[...]

6-2 S UPER S ERVER 7048R-C1R T4+/7048R-C1R4+ User's Manual Figure 6-1. Chassis Front View System Reset Main Power One 5.25" Drive Bay USB Ports Enclosure for Eight 2.5" Hard Drive Bays Eight 3.5" Hard Drive Bays (behind locking bezel)[...]

Chapter 6: Advanced Chassis Setup 6-3 6-2 Front Control Panel The front control panel must be connected to the JF1 connector on the serverboard to provide you with system status and alarm indications. A ribbon cable has bundled these wires together to simplify this connection. Connect the cable from JF1 on the serverboard (making sure the red wire [...]

6-4 S UPER S ERVER 7048R-C1R T4+/7048R-C1R4+ User's Manual 6-3 System Fans Three 8-cm chassis cooling fans (located in the center of the chassis) provide cool - ing airow while two 8-cm exhaust fans expel hot air from the chassis. The chassis is also tted with an air shroud to concentrate the ow of cooling air over the areas of highes[...]

Chapter 6: Advanced Chassis Setup 6-5 Figure 6-4. Removing the Air Shroud Figure 6-3. Removing a Chassis Fan Removing the Air Shroud Under most circumstances you will not need to remove the air shroud to perform any service on the system. However , if you wish to temporarily remove it (the air shroud should always be in place when the system is ope[...]

6-6 S UPER S ERVER 7048R-C1R T4+/7048R-C1R4+ User's Manual Installing/Removing Hard Drives 1. T o remove a carrier , rst open the front bezel. 2. Push the release button located beside the drive LEDs (See Figure 6-5). 3. Swing the handle fully out and then use it to pull the unit straight out. Note: Y our operating system must have RAID sup[...]

Chapter 6: Advanced Chassis Setup 6-7 Figure 6-6. Mounting a Drive in a Carrier W arning: Use extreme caution when working around the SAS/SA T A backplane. Do not touch the backplane with any metal objects and make sure no cables touch the backplane or obstruct the airow holes. Figure 6-5. Removing a Drive Carrier SAS/SA T A Backplane The SAS/SA[...]

6-8 S UPER S ERVER 7048R-C1R T4+/7048R-C1R4+ User's Manual Installing Components in the 5.25" Drive Bays The 7048R-C1RT4+/7048R-C1R4+ has one 5.25" drive bay into which a DVD-ROM drive may be installed. 1. First power down the system and then remove the top/left chassis cover to access the drive components. 2. With the cover of f, re[...]

Chapter 6: Advanced Chassis Setup 6-9 Figure 6-7. Rotating the Mobile Rack Enclosure Release Lever Mobile Rack Mobile Rack Enclosure Note: image above is for illustrative purposes - the mobile rack enclosure does not need to be removed in order to remove the mobile rack. 6. T urn the module 90 degrees (as illustrated). 7. Reinsert the module into t[...]

6-10 S UPER S ERVER 7048R-C1R T4+/7048R-C1R4+ User's Manual 6-5 Power Supply The SuperServer 7048R-C1RT4+ has a redundant, hot-plug 1000 watt power supply consisting of two power modules. The 7048R-C1R4+ has a redundant, hot-plug 920 watt power supply consisting of two power modules. Each power supply module has an auto-switching capability , [...]

Chapter 7: BIOS 7-1 Chapter 7 BIOS 7-1 Introducti on This chapter describes the AMI BIOS setup utility for the X10DRC/i-LN4+/-T4+ . The ROM BIOS is stored in a Flash EEPROM and can be easily updated. This chapter describes the basic navigation of the AMI BIOS setup utility screens. Starting BIOS Setup Utility T o enter the AMI BIOS setup utility sc[...]

7-2 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual How to Start the Setup Utility Normally , the only visible Power-On Self-T est (POST) routine is the memory test. As the memory is being tested, press the <Delete> key to enter the main menu of the AMI BIOS setup utility . From the main menu, you can access the other setup screens[...]

Chapter 7: BIOS 7-3 The following Main menu items will be displayed: System Date/System Time Use this option to change the system date and time. Highlight System Date or System Time using the arrow keys. Enter new values using the keyboard. Press the <T ab> key or the arrow keys to move between elds. The date must be entered in Day MM/DD/Y[...]

7-4 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual 7-3 Advanced Setup Congurations Use the arrow keys to select Advanced setup and press <Enter> to access the submenu items: W arning : T ake Caution when changing the Advanced settings. An incorrect value, a very high DRAM frequency or an incorrect BIOS timing setting may cause [...]

Chapter 7: BIOS 7-5 W ait For 'F1' If Error Select Enabled to force the sys tem to wa it unt il th e <F1 > key is p res se d if an e rr or oc cu rs. T he o pti ons a re D isa ble d and Enabled . INT19 (Interrupt 19) T rap Response Interrupt 19 is the software interrupt that handles the boot disk function. When this item is set to Im[...]

7-6 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual  CPU Conguration This submenu displays the following CPU information as detected by the BIOS. It also allows the user to congure CPU settings. • Processor Socket • Processor ID • Processor Frequency • Processor Max Ratio • Processor Min Ratio • Mic[...]

Chapter 7: BIOS 7-7 illegal codes to overwhelm the processor to damage the system during an attack. The options are Enable and Disable. (Refer to Intel's and Microsoft's websites for more information.) PPIN Control Select Unlock/Enable to use the Protected-Processor Inventory Number (PPIN) control in the system. The options are Unlock/Ena[...]

7-8 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual AES-NI Select Enable to use the Intel Advanced Encryption Standard (AES) New Instruc - tions (NI) to ensure data security . The options are Enable and Disable . Intel Virtualization T echnology Select Enable to use Intel Virtualization T echnology support for Direct I/O VT -d sup - port[...]

Chapter 7: BIOS 7-9  CPU C State Control (Available w hen Power T echnology is set to Custom) Package C State limit Use this item to set the limit on the C-State package register . The options are C0/1 state, C2 state, C6 (non-Retention) state, and C6 (Retention) state . CPU C3 Report Select Enable to allow the BIOS to report the CPU C3 State (A[...]

7-10 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual  Chipset Conguration W arning! Please set the correct settings for the items below . A wrong conguration setting may cause the system to become malfunction.  North Bridge This feature allows the user to congure the settings for the Intel North Bridge.  IIO Congurat[...]

Chapter 7: BIOS 7-1 1 II01 PORT 3A Link Speed This item congures the link speed of a PCI-E port specied by the user. The options are Gen 1 (Generation 1) (2.5 GT/s), Gen 2 (Generation 2) (5 GT/s), and Gen 3 (Generation 3) (8 GT/s) . II01 PORT 3C Link Speed This item congures the link speed of a PCI-E port specied by the user. The option[...]

7-12 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual  IOA T (Intel® IO Acceleration) Conguration Enable IOA T Select Enable to enable Intel I/OA T (I/O Acceleration T echnology) support, which signicantly reduces CPU overhead by leveraging CPU architectural improve - ments and freeing the system resource for other tasks. The op[...]

Chapter 7: BIOS 7-13 • Current QPI Link Frequency • QPI Global MMIO Low Base/Limit • QPI Global MMIO High Base/Limit • QPI PCIe Conguration Base/Size Link Frequency Select Use this item to select the desired frequency for QPI Link connections. The op - tions are 6.4GB/s, 8.0GB/s, 9.6GB/s, Auto, and Auto Limited. Link L0p Enab[...]

7-14 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual Data Scrambling Select Enabled to enable data scrambling to enhance system performance and data integrity . The options are Auto , Disabled and Enabled. DRAM RAPL (Running Average Power Limi t) Baseline Use this feature to set the run-time power-limit baseline for DRAM modules. The opt[...]

Chapter 7: BIOS 7-15 Patrol Scrub Patrol Scrubbing is a process that allows the CPU to correct correctable memory errors detected on a memory module and send the correction to the requestor (the original source). When this item is set to Enable, the IO hub will read and write back one cache line every 16K cycles, if there is no delay caused by inte[...]

7-16 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual XHCI Hand-Off This is a work-around solution for operating systems that do not support XHCI (Ex - tensible Host Controller Interface) hand-off. The XHCI ownership change should be claimed by the XHCI driver . The settings are Enabled and Disabled. EHCI Hand-Off This item is for operati[...]

Chapter 7: BIOS 7-17  SA T A Conguration When this submenu is selected, AMI BIOS automatically detects the presence of the SA T A devices that are supported by the Intel PCH chip and displays the fol - lowing items: SA T A Controller Select Enabled to enable the onboard SA T A controller supported by the Intel PCH chip. The options are Enable[...]

7-18 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual *If the item above "Congure SA T A as" is set to IDE, the following items will display: Serial A T A Port 0~ Port 5 This item indicates that a SA T A port specied by the user is installed (present) or not. Port 0 ~ Port 5 SA T A Device T ype (Available when a SA T A por[...]

Chapter 7: BIOS 7-19 Port 0 ~ Port 5 Spin Up Device On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRE - SET initialization to the device. The options are Enabled and Disabled . Port 0 ~ Port 5 SA T A Device T ype Use this item to specify if the SA T A port specied by the user should be con - nected to a Solid State d[...]

7-20 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual sSA T A Port 0 ~ Port 3 Spin Up Device On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRE - SET initialization to the device. The options are Enabled and Disabled . Port 0 ~ Port 3 sSA T A Device T ype Use this item to specify if the sSA T A port specied [...]

Chapter 7: BIOS 7-21 sSA T A Port 0~ Port 3 This item displays the information detected on the installed sSA T A drives on the particular sSA T A port. • Model number of drive and capacity sSA T A Port 0~ Port 3 Select Enabled to enable an sSA T A port specied by the user . The options are Disabled and Enabled. sSA T A Port 0 ~ Port 3 Spin [...]

7-22 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual  PCIe/PCI/PnP Conguration The following PCI information will be displayed: • PCI Bus Driver V ersion • PCI Device Common Settings PCI Latency Timer Use this item to congure the PCI latency timer for a device installed on a PCI bus. Select 32 to set the PCI latency ti[...]

Chapter 7: BIOS 7-23 ASPM Support Use this item to set the Active State Power Management (ASPM) level for a PCI-E device. Select Auto for the system BIOS to automatically set the ASPM level based on the system conguration. Select Disabled to disable ASPM support. The options are Disabled and Auto. W arning : Enabling ASPM support may cause some [...]

7-24 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual  Super IO Conguration Super IO Chip AST2400  Serial Port 1 Conguration/Serial Port 2 Conguration Serial Port 1/Serial Port 2 Select Enabled to enable the onboard serial port specied by the user. The options are Enabled and Disabled. Device Settings This item displays [...]

Chapter 7: BIOS 7-25 *If the item above set to Enabled, the following items will become available for conguration:  COM1 Console Redirection Settings T erminal T ype Use this item to select the target terminal emulation type for Console Redirec - tion. Select VT100 to use the ASCII Character set. Select VT100+ to add color and function key su[...]

7-26 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual VT -UTF8 Combo Key Support Select Enabled to enable VT -UTF8 Combination Key support for ANSI/VT100 terminals. The options are Enabled and Disabled . Recorder Mode Select Enabled to capture the data displayed on a terminal and send it as text messages to a remote server . The options a[...]

Chapter 7: BIOS 7-27  SOL/COM2 Console Redirection Settings Use this feature to specify how the host computer will exchange data with the client computer , which is the remote computer used by the user . T erminal T ype Use this feature to select the target terminal emulation type for Console Redirec - tion. Select VT100 to use the ASCII Charact[...]

7-28 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual VT -UTF8 Combo Key Support Select Enabled to enable VT -UTF8 Combination Key support for ANSI/VT100 terminals. The options are Enabled and Disabled . Recorder Mode Select Enabled to capture the data displayed on a terminal and send it as text messages to a remote server . The options a[...]

Chapter 7: BIOS 7-29 Serial Port for Out-of-Band Management/Window s Emergency Management Services (EMS) The submenu allows the user to congure Console Redirection settings to support Out-of-Band Serial Port management. EMS Console Redirection Select Enabled to use a COM port selected by the user for EMS Console Redirec - tion. The options are E[...]

7-30 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual Flow Control Use this item to set the ow control for Console Redirection to prevent data loss caused by buffer overow. Send a "Stop" signal to stop data-sending when the receiving buffer is full. Send a "Start" signal to start data-sending when the receiving b[...]

Chapter 7: BIOS 7-31  Intel TXT (L T -SX) Conguration This submenu allows the user to congure the following TXT settings. TXT Support Select Enabled to enable Intel T rusted Execution T echnology (TXT) support. The options are Disabled and Enabled. Note : If the option for this item (TXT Support) is set to Enabled, be sure to disable EV DF[...]

7-32 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual 7-4 E vent Logs Use this feature to congure Event Log settings.  Change SMBIOS Event Log Settings This feature allows the user to congure SMBIOS Event settings. Enabling/Disabling Options SMBIOS Event Log Select Enabled to enable SMBIOS (System Management BIOS) Event Logging d[...]

Chapter 7: BIOS 7-33 Erasing Settings Erase Event Log Select Y es to erase all error events in the SMBIOS (System Management BIOS) log before an event logging is initialized at bootup. The options are No and Y es. When Log is Full Select Erase Immediately to immediately erase all errors in the SMBIOS event log when the event log is full. Select Do [...]

7-34 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual 7 -5 I PMI Use this feature to congure Intelligent Platform Management Interface (IPMI) settings. BMC (Baseboard Management Controller) Firmware Revision This item indicates the BMC rmware revision used in your system. IPMI Status This item indicates the status of the IPMI rmw[...]

Chapter 7: BIOS 7-35 When SEL is Full This feature allows the user to determine what the AMI BIOS should do when the system event log is full. Select Erase Immediately to erase all events in the log when the system event log is full. The options are Do Nothing and Erase Immediately . Note : After making changes on a setting, be sure to reboot the s[...]

7-36 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual 7-6 Security Settings Thi s me nu a llo ws t he u ser to c on g ure the fol low ing sec ur it y set ti ngs for the syste m. Password Check Select Setup for the system to prompt for a password upon entering the BIOS setup utility . Select Always for the system to prompt for a passwor[...]

Chapter 7: BIOS 7-37 7-7 Boot Settings Use this featu re to c on g ure Boot Set ti ngs: Boot Conguration Setup Prompt Timeout Use this item to indicate how many seconds the system shall wait for the BIOS setup activation key to respond before the system starts to boot. The default setting is 1 . Boot Mode Select Use this item to select the ty[...]

7-38 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual  Delete Boot Option Use this item to select a boot device to delete from the boot priority list. Delete Boot Option Select the target boot device to delete.  Hard Disk Drive BBS Priorities • Legacy Boot Order #1  Network Drive BBS Priorities • Legacy Boot Order #1 ?[...]

Chapter 7: BIOS 7-39 7-8 Save & Exit Select the Save & Exit tab from the BIOS setup screen to congure the settings below . Discard Changes and Exit Select this option to exit from the BIOS setup without making any permanent changes to the system conguration, and reboot the computer . Select Discard Changes and Exit from the Exit menu [...]

7-40 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual Save As User Defaults Select this item and press <Enter> to save the current BIOS settings as user's default settings for future use. Restore User Defaults Select this item and press <Enter> to retrieve user-dened settings that were previ - ously saved for future us[...]

A-1 Appendix A: BIOS Error Beep Codes Appendix A BIOS Error Beep Codes During the POST (Power-On Self-T est) routines, which are performed each time the system is powered on, errors may occur . Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process. The error messages normally appear on the screen. Fatal e[...]

A-2 S UPER S ERVER 7048R-C1R4+/7048R-C1RT4+ User's Manual Notes[...]

B-1 Appendix B: System Specications Appendix B System Specications Processors Sin gle o r dua l Intel ® E5-2600 (v3) Series processors in Socket R, LGA 201 1 sockets (both CPUs must be of the same type) No te: Pl eas e re fer t o ou r web s it e for a c o mp let e li st ing o f su pp or t ed p ro c es so rs . Chipset Intel C612 chipset BIOS [...]

B-2 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual Expansion Slots T wo PCI-E 3.0 x16 slots, three PCI-E 3.0 x8 slots and one PCI-E 2.0 x4 (in x8) slots Serverboard X10DRC-T4+/X10DRC-LN4+ Dimensions: 13.7" (L) x 13.1" (W) (347 mm x 331 mm) Chassis 7048R-C1RT4+: SC745TQ-R1K03B, tower/4U r ackmount 7048R-C1R4+: SC745TQ-R920B, to[...]

B-3 Appendix B: System Specications Power Supply 7048R-C1RT4+ Rated Output Power: 1000W (Part# PWS-1K03A-1R) Rated Output V oltages: +12V (66.7A @ 800W, 83A @ 1000W), +5Vsb (4A) 7048R-C1R4+: Rated Output Power: 920W (Part# PWS-920P-1R) Rated Output V oltages: +12V (75A), +5Vsb (4A) Operating Environment Operating T emperature: 10º to 35º C (50[...]

B-4 S UPER S ERVER 7048R-C1RT4+/7048R-C1R4+ User's Manual (continued from front) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency com - munication devices or other critical systems whose failure to [...]