Symbol Technologies LS 3070 manual

LS 3070 Pr oduct Refer ence Guide 70-10294-02 Revision B February 1998 About This Manual T able of Contents Copyright Feedback Index  Click on red text at any location in the manual to jump to the specified chapter , topic, or reference.[...]

© 1997 SYMBO L TECHNOLOGIES, INC. All rights reserved. No part of this publication may be reproduced or used in any fo r m, or by any electrical or mechanical means, without pe r mission in writing from the publishe r . This includes electronic or mechanical means, such as photocopying, recording, or info r mation storage and retrieval systems. Th[...]

i Contents About This Manual Notational Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About-i Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About-i Service Information . . . . . . . .[...]

ii LS 3070XLR Extra Long Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 LS 3070HV High Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10 Chapter 4. Maintenance and Specifications Maintenance . . . . . . . . . . . . . .[...]

iii Code Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Code Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Code 39 Full ASCII . . . . . . . . . . . . . . . . . .[...]

iv UPC-A Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-37 UPC-E Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-38 Pause Duration . . . . . . . . . . . . . . . . . [...]

About-i About This Manual The LS 3070 Product Refer ence Guide provides general instr uctions for setup, operation, troubleshooting, maintenance, and pr ogramming. Notational Con ventions The following conventions are used in this document: • Bullets (•) indicate: - action items - lists of alternatives - lists of requir ed steps that are not ne[...]

About-ii LS 3070 Product Reference Guide: About This Manual Note : Symbol Technologies is not r esponsible for any damages incurr ed dur- ing shipment if the appr oved shipping container is not used. Shipping the units impr operly can possibly void the warranty. If the original shipping con- tainer was not kept, contact Symbol to have another sent [...]

1-1 Chapter 1 The LS 3070 Cordless Scanner The Freedom of Cor dless Scanning The LS 3070 is a revolutionary , cordless appr oach to capturing bar coded data. The scanner communicates with your host computer through a low-power radio transmission instead of through a cable. W ith the LS 3070, you are free to scan and transmit without a physical cabl[...]

1-2 LS 3070 Product Reference Guide: The LS 3070 Cordless Scanner The LS 3070 Scanner Housed in rugged, durable plastic, the LS 3070 scanner combines accurate, aggressive bar code scanning with solid state dependability . Its ergonomic design ensures comfortable use for extended periods of time. This scanner combines premium visible laser diode (VL[...]

1-3 LS 3070 Product Reference Guide: The LS 3070 Cordless Scanner Rechar g eable Battery P ac k In the handle of the scanner , there is a rechar geable NiCad battery pack. This provides all power to the scanner during normal operation. It pr ovides 360 mA hours, which is sufficient for normal operation during an 8-hour shift. When fully depleted, [...]

1-4 LS 3070 Product Reference Guide: The LS 3070 Cordless Scanner The Base/Char ger Unit The base/charger unit has two primary functions. First, it is the base station interface that manages the flow of information from the scanner to the host device. Second, it is a charging stand which charges the scanner ’s battery module (located in the hand[...]

2-1 Chapter 2 Setup Unpac king Remove the LS 3070, the RL 470 base/charger unit, and the host interface cable from its packing and inspect each for evidence of physical damage. If any equipment was damaged in transit, call the Symbol Support Center at the number in the front matter . KEEP THE P ACKING . It is the approved shipping container and sho[...]

2-2 LS 3070 Product Reference Guide: Setup The RL 470 base station is a charger , host interface, and — significantly — receiving station for RF transmission. Ther efore, do not install the RL 470 inaccessibly under a table or buried in a desk drawer . At a minimum, mount the RL 470 on a table or desk top. For optimum RF performance, especiall[...]

2-3 LS 3070 Product Reference Guide: Setup Char ging the Battery Before its first use, the LS 3070 batteries must be char ged. T o do so: • Connect the power supply to the power input port on the front panel of the RL 470 base/charger , shown in Figure 1-3: RL 470 Base/Charger Unit on page 1-4 . • Connect the power supply to a receptacle suppl[...]

2-4 LS 3070 Product Reference Guide: Setup Note: When setting the address of the base, you automatically set the initial frequency on which the base and the scanner communicate. In order to minimize possible interference between systems, bases which are close to each other should be assigned sequential addresses. Set the address thr ough setting tw[...]

2-5 LS 3070 Product Reference Guide: Setup P airing Scanner with Base/Charger T o pair the scanner with the base/charger: • Scan the P AIRING bar code below or the bar code on the RL 470 base. • Then insert the scanner into the base/charger ’s cradle. Y ou have 15 seconds to do this, or there will be err or beeps (4 beeps = unsuccessful pairi[...]

2-6 LS 3070 Product Reference Guide: Setup • At that time, through the scanner ’s contact shoe, there is an exchange of information (addressing, RF channels, etc.) between the scanner and the base/charger ’s cradle. This occurs in less than a second. • After that exchange, the scanner and base/charger ar e pair ed. Successful pairing is ind[...]

2-7 LS 3070 Product Reference Guide: Setup Occasionally , ther e can be excessive interference on a channel fr om some other source of radio transmissions. In this case, the default channel of a system can be changed using the parameter codes for Set T ransmission Fr equency . If you find a particular scanner/base pair has trouble communicating ov[...]

3-1 Chapter 3 Scanning with the LS 3070 1. Read y Before starting to scan bar codes for data collection, make sur e: • The base station is connected to the host device. • The battery has been charged. • The scanner is paired with the base/char ger . 2. T est Aim the scanner toward a bar code and pr ess the trigger . When you press the trigger[...]

3-2 LS 3070 Product Reference Guide: Scanning with the LS 3070 If the scanning attempt ends in 4 error beeps, any of these may be tr ue: • Scanner is out of transmission range • Scanner and base/charger ar e not paired • Base/charger is not power ed. Hold at an Angle Do not hold the scanner directly over the bar code. In this position, light [...]

3-3 LS 3070 Product Reference Guide: Scanning with the LS 3070 Using a Long Range or High Visibility Scanner? These scanners have two-position triggers. Press the trigger to the first detent and center the “collapsed” aiming beam on the target bar code, as illustrated below . The collapsed beam helps to establish the correct scanning position.[...]

3-4 LS 3070 Product Reference Guide: Scanning with the LS 3070 Scanning T ransmission Rang e RF Comm unication Error s RF communication errors occur when the scanner is out of range fr om the base during a scan data transmission attempt. An error is indicated by 6 beeps after a bar code is scanned, although the bar code data appears on the host dis[...]

3-5 LS 3070 Product Reference Guide: Scanning with the LS 3070 What If ... Nothing happens when y ou f ollow the operating instructions? Y ou should • Check that the power supply is attached to the base/charger . • Check for loose cable connections at the base/charger and host device. • Check the scanner ’s battery pack. • Make sure the d[...]

3-6 LS 3070 Product Reference Guide: Scanning with the LS 3070 Decode Zones LS 3070 Standar d Range Figure 3-1. LS 3070 Decode Zone: Depth of field as a function of minimum element width. Front of the Scanner NOTE: T ypical per formance at 23 o C (75 o F) on high quality symbols. 5 10 15 20 25 0 .055 In. Minimum Element Width .0075 In. 0 .0055 In.[...]

3-7 LS 3070 Product Reference Guide: Scanning with the LS 3070 LS 3070LR Long Range Figure 3-2. LS 3070LR Decode Zone: Depth of field as a function of minimum element width. Front of the Scanner 20 30 40 70 80 0 70 Mil Reflective 15 Mil 0 120 144 10 10 10 Inches 20 20 0 25.4 25.4 51 51 In. Cm. Width of Field 50 60 110 130 51 76 102 178 203 0 305 [...]

3-8 LS 3070 Product Reference Guide: Scanning with the LS 3070 LS 3070ALR Adv anced Long Rang e Figure 3-3. LS 3070ALR Decode Zone: Depth of field as a function of minimum element width. Front of the Scanner 40 60 80 140 160 0 70 Mil Reflective 15 Mil 0 200 240 10 10 20 Inches 20 20 0 25.4 25.4 51 51 In. Cm. Width of Field 100 120 180 220 102 152[...]

3-9 LS 3070 Product Reference Guide: Scanning with the LS 3070 LS 3070XLR Extra Long Range Figure 3-4. LS 3070XLR Decode Zone: Depth of field as a function of minimum element width. Front of the Scanner 40 60 80 140 160 0 55 Mil 30 Mil 0 10 10 20 Inches 20 20 0 25.4 25.4 51 51 In. Cm. Width of Field 100 120 180 102 152 203 356 406 0 51 Cm 254 305 [...]

3-10 LS 3070 Product Reference Guide: Scanning with the LS 3070 LS 3070HV High Visibility Figure 3-5. LS 3070HV Decode Zone: Depth of field as a function of minimum element width. Front of the Scanner 5 10 15 20 25 0 .055 In. Minimum Element Width .0075 In. 13 13 0 .020 In. Minimum Element Width . 040 In. Minimum Element Width 30 34 5 5 12.7 25.4 [...]

4-1 Chapter 4 Maintenance and Specifications Maintenance Cleaning the exit window is the only maintenance requir ed. A dirty window may affect scanning accuracy . • Do not allow any abrasive material to touch the window . • Remove any dirt particles with a damp cloth. • W ipe the window using a tissue moistened with ammonia/water . • Do no[...]

4-2 LS 3070 Product Reference Guide: Maintenance and Specifications Changing Battery P acks Y ou can charge battery packs on the Universal Four Slot Battery Charger so that a charged battery pack is available when needed. In this case, simply remove the depleted battery pack and r eplace it with a freshly charged one. User instructions ar e in the [...]

4-3 LS 3070 Product Reference Guide: Maintenance and Specifications 1. Remove Lo wer Handle from Scanner . Using a probe, pr ess in the release button on the handle, as indicated at the right. W ith button pressed in below the outer housing, slide the battery pack out from the handle. 2. Inser t Charged Battery P ack in Handle. W ith release button[...]

4-4 LS 3070 Product Reference Guide: Maintenance and Specifications Char ge Status LED Indications On the base/charger , there is a red LED indicator which uses flashing patterns to indicate the current char ger status. The red Char ge Status LED indicates the following conditions: • RED LED OFF — The scanner is not properly inserted or the ba[...]

4-5 LS 3070 Product Reference Guide: Maintenance and Specifications Accessories Standar d Accessories Part Number Description RL 470 Base/interface charger Base/Charger Cable: Cables are available for most applications. See the Electronic Pr oductOrdering Guide for more information. 70-10294-01 LS 3070 Product Refer ence Guide 70-10538-01 LS 3070 A[...]

4-6 LS 3070 Product Reference Guide: Maintenance and Specifications LS 3070 Standar d T echnical Specifications ITEM DESCRIPTION Power Requirements : Scanner 4.75 to 14 VDC; 210 mA @ 5 VDC T ypical. Base/Charger 5 VDC ± 10% @ 190 mA T ypical. 12 VDC ± 10% @ 400 mA T ypical. Scan Repetition Rate Approximately 36 (± 3) scans/sec (bidirectional) S[...]

4-7 LS 3070 Product Reference Guide: Maintenance and Specifications LS 3070LR T echnical Specifications ITEM DESCRIPTION Power Requirements : Scanner 4.75 to 14 VDC; 210 mA @ 5 VDC T ypical. Base/Charger 5 VDC ± 10% @ 190 mA T ypical. 12 VDC ± 10% @ 400 mA T ypical. Scan Repetition Rate Approximately 36 (± 3) scans/sec (bidirectional) Start-up [...]

4-8 LS 3070 Product Reference Guide: Maintenance and Specifications LS 3070ALR T echnical Specifications ITEM DESCRIPTION Power Requirements : Scanner 4.75 to 14 VDC; 210 mA @ 5 VDC T ypical. Base/Charger 5 VDC ± 10% @ 190 mA T ypical. 12 VDC ± 10% @ 400 mA T ypical. Scan Repetition Rate Approximately 36 (± 3) scans/sec (bidir ectional) Start-u[...]

4-9 LS 3070 Product Reference Guide: Maintenance and Specifications LS 3070XLR T echnical Specifications ITEM DESCRIPTION Power Requirements : Scanner 4.75 to 14 VDC; 210 mA @ 5 VDC T ypical. Base/Charger 5 VDC ± 10% @ 190 mA T ypical. 12 VDC ± 10% @ 400 mA T ypical. Scan Repetition Rate Approximately 36 (± 3) scans/sec (bidirectional) Start-up[...]

4-10 LS 3070 Product Reference Guide: Maintenance and Specifications LS 3070HV T echnical Specifications ITEM DESCRIPTION Power Requirements : Scanner 4.75 to 14 VDC; 210 mA @ 5 VDC T ypical. Base/Charger 5 VDC ± 10% @ 190 mA T ypical. 12 VDC ± 10% @ 400 mA T ypical. Scan Repetition Rate Approximately 36 (± 3) scans/sec (bidirectional) Start-up[...]

5-1 Chapter 5 Interface Guide Connecting to a Host De vice In most cases, connecting your LS 3070’s base station to your host terminal is a very simple operation. Y ou need only plug the cable into your host. T ypical configurations are shown on the following pages. Some POS keyboar ds require more intricate installation instr uctions. Those beg[...]

5-2 LS 3070 Product Reference Guide: Interface Guide Connecting Base Station to a Host OCIA and OCR T erminals The OCIA or OCR port must be activated and refer enced by the POS system, or no communications will take place. Figure 5-1. Connecting Base Station to OCIA/OCR T erminals These include: OCR IBM 3653/3683/3684, Fujitsu 7770/7880/7990/8770/9[...]

5-3 LS 3070 Product Reference Guide: Interface Guide RS-232C Single P or t Figure 5-2. Connecting Base Station to RS-232C Single-Port Host Any of the following RS-232C (DB 25) connectors are supported: Male, TxD on pin 2 or TxD on pin 3. Female, TxD on Pin 2 or Pin 3. For other pinouts and cable types, contact the Symbol Support Center at 1-800-653[...]

5-4 LS 3070 Product Reference Guide: Interface Guide IBM 4683/4684/4693/4694 Figure 5-4. Connecting Base Station to IBM 4683/4684/4693/4694 T o connect the base station, plug the cable into the appropriate port on the rear of the IBM 4683/84, 4693/94. For the IBM 4693, port 9C (which replaces port 17 on the 4683/84) is the appropriate port for conn[...]

5-5 LS 3070 Product Reference Guide: Interface Guide Connecting K eyboar d W edg es Figure 5-5. Connecting Base Station to Keyboar d Wedge These include: PC Ke yboards IBM PC/A T/XT , PS2-30/50/55SX/60/70 and clones. T erminal Ke yboards DEC VT2XX/VT3XX/4XX; HP 700/92, 2392; IBM 3178/3278/3151/316X/ 3179/3180/319X, 3278, 347X; T elex-Memorex 88, 12[...]

5-6 LS 3070 Product Reference Guide: Interface Guide IBM 3683/3684 Installation Caution Install cables as described below . Failure to do so may re- sult in hardwar e damage. There ar e four basic steps to this installation: 1. Remove the IBM 3683/84 top cover . 2. Remove the keyboard. 3. Install the cable internally or externally . 4. Replace the [...]

5-7 LS 3070 Product Reference Guide: Interface Guide Third: Install the Cable Internall y The base station cable is installed internal to the IBM 3683/84 with the cable exiting the rear of the terminal. 1. Remove the printer assembly as follows: • Disconnect the printer ground strap (slide on connector) fr om the right side of the printer , as sh[...]

5-8 LS 3070 Product Reference Guide: Interface Guide Fourth: Replace the K eyboard and T op Cover 1. Replace the keyboard down into the r etaining glides. 2. Replace the top cover as follows: • Replace the display cable if display is integrated. • Hold the cover so that rear slots fit into r etaining tabs. • Lower the cover at front to engag[...]

5-9 LS 3070 Product Reference Guide: Interface Guide Figure 5-7. Disconnecting Cable from Connector Figure 5-8. Sliding Printer Locking T abs Printer Ground Strap Connector Locking T ab[...]

5-10 LS 3070 Product Reference Guide: Interface Guide Figure 5-9. Cable Figure 5-10. J16 Connector[...]

5-1 1 LS 3070 Product Reference Guide: Interface Guide Figure 5-11. Connecting J2 to J16 Figure 5-12. Securing J1[...]

5-12 LS 3070 Product Reference Guide: Interface Guide IBM 3653 Installation 1. Be sure the IBM 3653 terminal is power ed-down. Open the door over the ribbon cartridge as shown in Figure 5-13 . 2. Loosen the right side panel screw (see Figur e 5-13 ). Grasp the right panel at top of the rear corner; pull out to the side and push back to r emove the [...]

5-13 LS 3070 Product Reference Guide: Interface Guide 1 1. Remove the protective foam fr om the register end of the base station Y - cable, and insert into the cable assembly . Place the assembly near the bottom of the register behind the keyboar d. 12. Install the keyboard connector , as shown in Figure 5-19 . Secure with the tie wrap that doesn&a[...]

5-14 LS 3070 Product Reference Guide: Interface Guide Figure 5-14. Removing Ke yboard Co ver Figure 5-15. Sliding Base Station Cable Through Hole Screws[...]

5-15 LS 3070 Product Reference Guide: Interface Guide Figure 5-16. Opening Card Cage Figure 5-17. Connecting Probes[...]

5-16 LS 3070 Product Reference Guide: Interface Guide Figure 5-18. V oltage Adjustment Hole Figure 5-19. Installing Keyboar d Connector[...]

5-17 LS 3070 Product Reference Guide: Interface Guide NCR 280 Installation 1. Ensure that the NCR 280 is power ed down and unplugged. Open the door on the top, left-hand side and remove the two scr ews which fasten the steel plate to the terminal cover . Slide the steel plate to the left to remove. 2. Remove the two round head scr ews from the back[...]

5-18 LS 3070 Product Reference Guide: Interface Guide 12. Cut a 1-in. diameter semicircle at the bottom left of the terminal cover , approximately 6 1/2 in. fr om the back of the unit, so that when the cover is replaced, this opening fits over the cable. Be sur e to file down all sharp edges. 13. Replace the terminal cover making sure that cable [...]

5-19 LS 3070 Product Reference Guide: Interface Guide 5. Locate the end of the RL 470 base station cable that branches into a “Y”. Slide that end under the board assembly inside the r egister . Leave enough slack to make the connection requir ed in the next few steps. 6. Mate the RL 470 base station cable “Y” branch ending in a 2 x13 female[...]

5-20 LS 3070 Product Reference Guide: Interface Guide NCR 2152 Installation 1. Switch off the NCR 2152. Remove the two lar ge, pan head scr ews fr om the front of the terminal to allow the top section to open up. Use the two hood support rods located to the sides of the housing to support the top section. 2. Locate the large steel plate covering th[...]

5-21 LS 3070 Product Reference Guide: Interface Guide NCR 2154/2155 Installation 1. Power-down the NCR 2154/2155 POS terminal. 2. Remove the keyboard by grasping the keyboar d cover at its corners and lifting upward. 3. Remove the cable connecting the keyboard to the terminal’s main PC board. 4. Install the LL 500 cable in place of the keyboard c[...]

5-22 LS 3070 Product Reference Guide: Interface Guide Fujitsu 9000 Installation 1. Switch-off the Fujitsu 9000, and disconnect the power . Push down on the keyboard r elease latch below the keyboar d. Pull the keyboard forwar d, lift and remove 2. Press down the printer r elease tab. Push the printer back and remove. Press down the display release [...]

5-23 LS 3070 Product Reference Guide: Interface Guide Interfaces Select the appropriate interface cable assembly for your host system. Host T ype Interface P/N DEC VT 2XX/3XX/4XX W edge IK-1400 Fujitsu 7770, 7880, 7990, 8770 OCR IK-0901 Fujitsu 9000 OCR IK-0900 Fujitsu 9000 W edge IK-0403 HP 700/XX, 239X W edge IK-1301 RS-232C TxD on Pin 2, Male RS[...]

5-24 LS 3070 Product Reference Guide: Interface Guide Host T ype Interface P/N NCR 280 W edge IK-0700 NCR 2126-1 120 OCIA IK-1004 NCR 2151 W edge IK-0600 NCR 2152 W edge IK-0500 NCR 2152/2257/2950 OCIA IK-1001 NCR 2154/2155/2157/7050 OCIA IK-1002 NCR 7052 OCIA IK-1000 NCR 7052 W edge IK-0402 Nixdorf 8812 OCIA IK-1003 T elex Memorex 88, 122 W edge I[...]

6-1 Chapter 6 Pr ogramming Pr ogramming Over view Before pr ogramming, follow the instructions in the Chapter 2: Setup and Chapter 5: Interface Guide . Programming occurs thr ough use of bar code menus. Not all parameters, however , apply to your specific host. For example, if you have an OCIA terminal, RS-232C parameters such as baud rate and par[...]

6-2 LS 3070 Product Reference Guide: Programming Scanning Sequence Examples In most cases you need only scan one bar code to set a specific parameter . For example, if you want to set the baud rate to 9600, simply scan the 9600 bar code listed under Baud Rate . The base station will issue a warble tone, signifying a successful parameter entry . If[...]

6-3 LS 3070 Product Reference Guide: Programming P arameter Descriptions Set P arameter Defaults Scanning the SET DEF AUL T bar code r eturns all parameters to the values listed in the Default T able beginning on page 6-28 . Host Interface Code Each Interface Cable Assembly defaults to a given host. These assemblies, their corresponding defaults, a[...]

6-4 LS 3070 Product Reference Guide: Programming One Discrete Length - This option will allow you to decode only those codes containing a selected length. For example, if you select D 2 of 5 One Discrete Length , then scan 1 , 4 , the only D 2 of 5 codes decoded will be those containing 14 characters T wo Discrete Lengths - This option will allow y[...]

6-5 LS 3070 Product Reference Guide: Programming Decode Options T ransmit UPC-E/UPC-A Check Digit Select if decoded UPC symbols are transmitted with or without a check digit. Con ver t UPC-E T o UPC-A Use this parameter to convert UPC-E (zero suppr essed) decoded data to UPC- A format before transmission. After conversion, data will follow UPC form[...]

6-6 LS 3070 Product Reference Guide: Programming Code 39 Check Digit When enabled, this parameter checks the integrity of a Code 39 symbol to ensure it complies with a modulo 43 check digit algorithm. ITF-14/EAN-13 Con version If your terminal supports EAN-13, this feature converts a 14 character I 2 of 5 code into EAN-13, and transmits to the host[...]

6-7 LS 3070 Product Reference Guide: Programming Beeper V olume Select degree of volume — high or low . Beep After Good Decode Determine if the unit beeper will sound during normal scanning. Usually it is desirable to operate the unit with the beeper enabled. In all cases, the beeper operates during parameter menu scanning and indicates error con[...]

6-8 LS 3070 Product Reference Guide: Programming Decode Redundancy Use this parameter to indicate whether the scanner must read a bar code one time ( LEVEL 1 ), two times ( LEVEL 2 ), or three times ( LEVEL 3 ) befor e decoding it. A higher level of redundancy ensures the accuracy of a decode in, for example, poor quality symbols. UPC-A and -E Prea[...]

6-9 LS 3070 Product Reference Guide: Programming Data T ransmission Formats Magstripe Data T ransmission Format Magstripe data format options are open for user determination with the specific application. The following are standar d selections: • Standard: <data as on card> • Option 1: <acct nr> • Option 2: <acct nr> <SU[...]

6-10 LS 3070 Product Reference Guide: Programming Scan Data T ransmission Format Scan data format options can be selected by the user . The following are standard selections: • Standard: <data as is> • Option 1: <data> <SUFFIX> • Option 2: <PREFIX> <data> <SUFFIX> • Option 3: <PREFIX> <data> &[...]

6-1 1 LS 3070 Product Reference Guide: Programming RS-232C Options Baud Rate Baud rate is the number of bits of data transmitted per second. The scanner's baud rate setting should match the data rate setting of the host device. If not, data may not reach the host device or may r each it in distorted form. P arity A parity check bit is the most[...]

6-12 LS 3070 Product Reference Guide: Programming • When the CTS line is negated, the base asserts the R TS line and waits for one second for the host to assert CTS. When the host asserts CTS, data is transmitted. • When data transmission is complete, the base will negate R TS 10 msec after sending the last character . • The host should respo[...]

6-13 LS 3070 Product Reference Guide: Programming Software Handshaking This parameter offers contr ol of the data transmission process. It may be used instead of, but not in conjunction with, hardwar e handshaking. The base station also provides four softwar e handshaking options: NONE, ENQ, ACK/ NAK, and ACK/NAK with ENQ. These options may be comb[...]

6-14 LS 3070 Product Reference Guide: Programming When you select the wait for ENQ option, the base station waits for an ENQ, Enquire character , from the host before it transmits data; otherwise the unit transmits data without waiting for an ENQ character from the host. W ith ENQ enabled, the base station must receive an ENQ fr om the host within [...]

6-15 LS 3070 Product Reference Guide: Programming Serial Response Timeout This parameter determines the maximum period allowed to elapse before the base station assumes end of transmission. The delay period can range from 0 to 9.9 seconds. Stop Bit Select The stop bit(s) at the end of each transmitted character marks the end of transmission of one [...]

6-16 LS 3070 Product Reference Guide: Programming Inter character Dela y Select the intercharacter delay option matching host device r equir ements. The intercharacter delay gives the host system time to service its r eceiver and perform other tasks between characters. Select from no delay to a 99 msec delay between the transmission of each charact[...]

6-17 LS 3070 Product Reference Guide: Programming OCIA T ransmit Timeout When connected to an OCIA terminal, the RL 470 base/interface will attempt to transmit the data to the host. If the host is not prepar ed to accept data at that time (i.e., the host data buffer may be full), the RL 470 will try to r etransmit the data for up to 3 seconds. If t[...]

6-18 LS 3070 Product Reference Guide: Programming National Ke yboard T ypes Use this parameter to set the national character type for keyboard characters. Selections include U.S. English, French, German, Fr ench International, Spanish, Italian, Swedish, and U.K. English. The following terminals do not support Italian or French International but do [...]

6-19 LS 3070 Product Reference Guide: Programming IBM 316X Y NNNNNNN IBM 319X Y NNNNNNN IBM 3178 Y NNNNNNN IBM 3278 Y NNNNNNN T elex - 88 Y NNNNNNN T elex - 122 Y NNNNNNN W yse 60/PC YYYYYYN N W yse 60/ASCII YYYYYYN N W yse 60/ANSI YYYYYYN N W yse 85/ANSI YYYY YNYN W yse 150/ANSI Y NNNNNNN W yse 150+/PC Y NNNNNNN W yse 150+/ASCII Y N N Y Y N N N W [...]

6-20 LS 3070 Product Reference Guide: Programming Set T ransmission Frequency Use this parameter to set an initial transmission frequency to avoid interference on the default channel (channel 50). During operation, the transmission channel changes automatically whenever interference is encountered 80% of the time or mor e over a continuous five-mi[...]

6-21 LS 3070 Product Reference Guide: Programming P arameter Selections Supported features for each host type. T able 6-2. Host Supported Parameters Decode Parameters RS-232C IBM 4683* OCIA OCR Keyboard W edge Add Codes to be Decoded XXXXX ASCII Format X Baud Rate X Beep After Good Decode XXXXX Beeper V olume XXXXX Check Parity X Codabar Any Length[...]

6-22 LS 3070 Product Reference Guide: Programming Decode Redundancy XXXXX EAN Zero Extend XXXXX Hardware Handshaking X Host Interface Code XXXXX IBM 468X/9X Mgstrpe Comm. X Ignore Unknown Chars. XXXXX Intercharacter Delay XX I 2 of 5 Any Length X XXX I 2 of 5 Length W ithin Range X XXX I 2 of 5 One Length X XXX I 2 of 5 T wo Lengths X XXX ITF-14/EA[...]

6-23 LS 3070 Product Reference Guide: Programming * Some parameters are pr ogrammed through host computer . Scan Suffix XXXXX Serial Response T ime-out X Software Handshaking X T ransmit AIM Code ID XXXXX T ransmit Code ID Chars. XXXXX T ransmit MSI Check Digit XXXXX T ransmit No Decode Message XXXXX T ransmit UPC-A Check Digit XXXXX T ransmit UPC[...]

6-24 LS 3070 Product Reference Guide: Programming Beeper Definitions Standar d Use Beeper Sequence Indication 1 Beep - short high tone A bar code symbol, or magstripe data was decoded (if decode beeper is enabled). 2 Beeps - long high tone Mis-match between the selected host and the interface cable. 4 Beeps - long high tone This signifies either [...]

6-25 LS 3070 Product Reference Guide: Programming P arameter Menu Scanning Beeper Sequence Indication 1 Beep - short high tone Correct entry scanned or corr ect menu sequence performed. 1 Beep - lo/hi tone Input error , incorrect bar code or CANCEL scanned, wrong entry , incorrect bar code programming sequence; r emain in program mode. 1 Beep - hi/[...]

6-26 LS 3070 Product Reference Guide: Programming Code 39 Buffering While there is data in the transmission buf fer , deleting Code 39 buffering capability via the parameter menu is not allowed. T o allow disabling of Code 39 buffering, first force the buf fer transmission (see T ransmit Buffer on page 6-27 ) or clear the buffer . Buffer Data T o [...]

6-27 LS 3070 Product Reference Guide: Programming T ransmit Buffer T o transmit the buffer , read a symbol containing either the first or second condition: 1. Only a start character , a plus (+), and a stop character . • The unit signals that the transmission buffer has been sent (a hi/lo beep). • Unit sends the buffer . • Unit clears the bu[...]

6-28 LS 3070 Product Reference Guide: Programming Default T able T able 6-3. Defaults Parameter Default Host Interface See default table, page 6-31 Code T ypes All Code Lengths: Code 39 Code 128 Codabar I 2 of 5 D 2 of 5 MSI Plessey 1 to 55 3 to 55 2 to 55 14 14 1 to 55 Decode Options T ransmit UPC-A Check Digit T ransmit UPC-E Check Digit Convert [...]

6-29 LS 3070 Product Reference Guide: Programming Scan Data T ransmission Format Data as is Laser Control: Laser On T ime-out 3 Sec RS-232C Options Baud Rate Parity Check Parity Hardwar e Handshaking Software Handshaking Serial Response T ime-out Stop Bit Select ASCII Data Format R TS Line State 9600 Odd Enabled None None 2.0 Sec Tw o 7 Bit Low Int[...]

6-30 LS 3070 Product Reference Guide: Programming ** Prefix/Suf fix values only apply when the selected transmission format uses them. For example, if you select the default setting for Scan Data T ransmission Format (Data As Is), any prefix or suffix selected is not r ecognized, since the format requir es neither .[...]

6-31 LS 3070 Product Reference Guide: Programming T erminal Specific RS-232C Defaults T wo RS-232C hosts are set up with their own parameter default settings. Selecting the ICL or Nixdorf RS-232C terminal will set the defaults listed below . These defaults take precedence over standard defaults. So, if you’ve selected Nixdorf RS-232C, then selec[...]

6-32 LS 3070 Product Reference Guide: Programming RS-232C Code 128 Code ID “D” None “K” RS-232C I 2 of 5 Code ID “F” “I” “I” RS-232C MSI/Plessey Code ID “J” None “O” T able 6-4. T erminal-Specific RS-232 Defaults Parameter Standard ICL NIXDORF[...]

7-1 Chapter 7 Parameter Menus While the last section provided descriptions of all parameter options and other programming information, this one pr ovides the bar codes to do the actual programming.[...]

7-2 LS 3070 Product Reference Guide: Programming Set Default P arameter Defaults are those listed in the Default T able beginning on page 6-28 . SET DEF A UL TS SET ICL RS-232C DEF A UL TS SET NIXDORF RS-232C DEF A UL TS[...]

7-3 LS 3070 Product Reference Guide: Programming Host Interface T o select a host interface: 1. Locate the type of interface from the list below . 2. Scan the corresponding bar code fr om those on the following pages. Host Interface Page RS-232C 7-4 RS-232 Single Port 7-4 RS-232 Dual Port 7-4 PC Keyboard IBM PC/A T 7-6 IBM PC/XT 7-6 IBM PS/2-30 7-6[...]

7-4 LS 3070 Product Reference Guide: Programming Note: In some cases, two bar codes may correspond to one interface type; this happens when differ ent software revisions exist for the same host type. If ther e are two bar codes for your host type, try the first bar code; if that does not work, then try the second one. Single P or t RS-232 Dual P o[...]

7-5 LS 3070 Product Reference Guide: Programming Four Options for Dual P ort RS-232: Dual P or t RS-232: T ransmit and Receive from P or t 1. Dual P or t RS-232: T ransmit to P orts 1 and 2 — Receive from P or t 1. Dual P or t RS-232: T ransmit and Receive from P or t 2. Dual P or t RS-232: T ransmit to P orts 1 and 2 — Receive from P or t 2.[...]

7-6 LS 3070 Product Reference Guide: Programming IBM PC/A T , IBM PS2-50/55SX/60/70/80 and Clones IBM PC/XT And Clones IBM 3653 Ke yboard Wedge IBM PS2-30 and Clones[...]

7-7 LS 3070 Product Reference Guide: Programming IBM 3683/3684 Calc 48 Ke yboard W edg e IBM 3683/3684 Calc 35 Ke yboard W edg e IBM 3683/3684 Calc 116 Ke yboard W edg e[...]

7-8 LS 3070 Product Reference Guide: Programming IBM 3683/3684 T el 116 Ke yboard W edg e IBM 3683/3684 T el 48 Ke yboard W edg e IBM 3683/3684 T el 35 Ke yboard W edg e[...]

7-9 LS 3070 Product Reference Guide: Programming NCR 2152 (T el) Keyboar d Wedge NCR 2151 (Calc) Ke yboard Wedge NCR 2152 (Calc) Ke yboard Wedge NCR 2151 (T el) Keyboar d Wedge[...]

7-10 LS 3070 Product Reference Guide: Programming NCR 255/2152/2154/2155, NCR 2126-1120 NCR 2157/2257/7050, NCR “S” 7052 OCIA NCR 7052 Ke yboard W edge NCR “F” 7052 OCIA NCR 280 Ke yboard Wedge[...]

7-1 1 LS 3070 Product Reference Guide: Programming Nixdorf 8812 OCIA ICL 9505/9507/9518/9520 OCIA Spectra Physics OCIA NCR “S” 2950 OCIA[...]

7-12 LS 3070 Product Reference Guide: Programming IBM 4683/4684 P or t 9B 4693 IBM 3653/3683/3684 OCR IBM 4683/4684 P or t 17 IBM 4683/4684 P or t 5B 4693[...]

7-13 LS 3070 Product Reference Guide: Programming HP 700-9X HP 239X DEC VT 220/320 Fujitsu 7770/7880/7990/ 8770/9000 OCR DEC VT 420[...]

7-14 LS 3070 Product Reference Guide: Programming IBM 3178 IBM 319X/347X/348X, T elex Memore x 122 IBM 3278 IBM 3151/316X IBM 3179/3180[...]

7-15 LS 3070 Product Reference Guide: Programming Wyse 50 (ASCII K eybd) T elex Memorex 88 Wyse 60 (ASCII K eybd) Wyse 150 / Wyse 150+ IBM 3180 (Later Software Revision) — See Note, p. 7-4. T elex 122 (V ariant ENTER Ke y from that on T elex Memore x 122)[...]

7-16 LS 3070 Product Reference Guide: Programming Wyse 60 (PC K eybd) Wyse 150 / Wyse 150+ Wyse 85/150+/185 (ANSI 105 K eybd) Wyse 60/150 (ANSI 101 K eybd) HP 2392 (Later Software Revision) — See Note, p. 7-4.[...]

7-17 LS 3070 Product Reference Guide: Programming Code T ype Add or delete specific code types by scanning the appropriate bar code(s). ENABLE ALL CODE TYPES DISABLE ALL CODE TYPES[...]

7-18 LS 3070 Product Reference Guide: Programming *Adding or deleting Code 39 Full ASCII only has an effect when Code 39 has been selected. ADD UPC/EAN ADD CODE 39 ADD CODE 39 FULL ASCII* DELETE CODE 39 DELETE CODE 39 FULL ASCII*[...]

7-19 LS 3070 Product Reference Guide: Programming DELETE UPC/EAN ADD CODE 128 DELETE CODE 128 ADD EAN 128 DELETE EAN 128[...]

7-20 LS 3070 Product Reference Guide: Programming ADD D 2 of 5 DELETE D 2 of 5 ADD I 2 of 5 DELETE I 2 of 5[...]

7-21 LS 3070 Product Reference Guide: Programming ADD MSI Plessey DELETE MSI Plessey ADD COD ABAR DELETE COD ABAR[...]

7-22 LS 3070 Product Reference Guide: Programming Code Lengths T o select two lengths for each code type: 1. Scan the desired option. 2. Scan two bar codes on page 7-27 - page 7-28 for each desired length. For example, for a length of “12”, scan “1” then “2”. For a length of “3”, scan “0”, then “3”. Y ou must always scan two[...]

7-23 LS 3070 Product Reference Guide: Programming CODE 128 - ANY LENGTH COD AB AR - 2 DISCRETE LENGTHS COD ABAR 1 - DISCRETE LENGTH COD ABAR - LENGTH WITHIN RANGE COD ABAR - ANY LENGTH[...]

7-24 LS 3070 Product Reference Guide: Programming * Choosing I 2 of 5 Any Length may lead to misreads for I 2 of 5 and UPC codes. I 2 OF 5 - ANY LENGTH* I 2 OF 5 - LENGTH WITHIN RANGE I 2 OF 5 - 1 DISCRETE LENGTH I 2 OF 5 - 2 DISCRETE LENGTHS[...]

7-25 LS 3070 Product Reference Guide: Programming D 2 OF 5 - ANY LENGTH D 2 OF 5 - LENGTH WITHIN RANGE D 2 OF 5 - 1 DISCRETE LENGTH D 2 OF 5 - 2 DISCRETE LENGTHS[...]

7-26 LS 3070 Product Reference Guide: Programming MSI Plessey - ANY LENGTH MSI Plessey - LENGTH WITHIN RANGE MSI Plessey - 1 DISCRETE LENGTH MSI Plessey - 2 DISCRETE LENGTHS[...]

7-27 LS 3070 Product Reference Guide: Programming 2 4 0 1 3 5[...]

7-28 LS 3070 Product Reference Guide: Programming 7 9 CANCEL 6 8[...]

7-29 LS 3070 Product Reference Guide: Programming Decode Options Enable or disable a specific decode option by scanning the appropriate bar code. TRANSMIT UPC-E CHECK DIGIT DO NO T TRANSMIT UPC-E CHECK DIGIT DO NO T TRANSMIT UPC-A CHECK DIGIT TRANSMIT UPC-A CHECK DIGIT[...]

7-30 LS 3070 Product Reference Guide: Programming . CONVERT UPC-E T O UPC-A DO NO T CONVERT UPC-E TO UPC-A ENABLE 2 MSI Plessey CHECK DIGITS ENABLE 1 MSI Plessey CHECK DIGIT[...]

7-31 LS 3070 Product Reference Guide: Programming A UTODISCRIMINA TE UPC/EAN SUPPLEMEN- DECODE UPC/EAN SUPPLEMENT ALS IGNORE UPC/EAN SUPPLEMENT ALS ENABLE EAN ZERO EXTEND DISABLE EAN ZERO EXTEND[...]

7-32 LS 3070 Product Reference Guide: Programming DO NO T TRANSMIT “NO DECODE” MESSA GE TRANSMIT “NO DECODED MESSA GE ITF14/EAN-13 CONVERSION DISABLED ITF14/EAN-13 CONVERSION ENABLED[...]

7-33 LS 3070 Product Reference Guide: Programming DO NO T BUFFER CODE 39 BUFFER CODE 39 VERIFY CODE 39 CHECK DIGIT DO NO T VERIFY CODE 39 CHECK DIGIT[...]

7-34 LS 3070 Product Reference Guide: Programming BI-DIRECTIONAL REDUND ANCY ENABLED BI-DIRECIT ONAL REDUNDANCY DISABLED BEEP AFTER GOOD DECODE DO NO T BEEP AFTER GOOD DECODE[...]

7-35 LS 3070 Product Reference Guide: Programming LO W BEEPER V OLUME HIGH BEEPER V OLUME UPC/EAN SECURITY LEVEL 0 UPC/EAN SECURITY LEVEL 1 UPC/EAN SECURITY LEVEL 2[...]

7-36 LS 3070 Product Reference Guide: Programming UPC/EAN SECURITY LEVEL 3 DECODE REDUND ANCY 1 DECODE REDUND ANCY 3 DECODE REDUND ANCY 2[...]

7-37 LS 3070 Product Reference Guide: Programming UPC-A Preamble Select one option for UPC-A preamble by scanning the appr opriate bar code. NONE SYSTEM CHARA CTER SYSTEM CHARA CTER & COUNTRY CODE[...]

7-38 LS 3070 Product Reference Guide: Programming UPC-E Preamble Select one option for UPC-E preamble by scanning the appr opriate bar code. NONE SYSTEM CHARA CTER SYSTEM CHARA CTER & COUNTRY CODE[...]

7-39 LS 3070 Product Reference Guide: Programming P ause Duration T o set a pause duration: 1. Scan the P AUSE DURA TION bar code below . 2. Scan two bar codes on the next two pages which repr esent the desired pause. Y ou must always scan two bar codes. 3. If you make an error , or wish to change your selection, scan CANCEL . P A USE DURA TION[...]

7-40 LS 3070 Product Reference Guide: Programming 2 4 0 1 3 5[...]

7-41 LS 3070 Product Reference Guide: Programming 7 9 CANCEL 6 8[...]

7-42 LS 3070 Product Reference Guide: Programming Prefix/Suffix V alues Note: These values will also be used for Advanced Data Formatting programming. See the Advanced Programmer ’s Guide for details. T o set a PREFIX/SUFFIX value: 1. Scan the option bar code you wish to set. 2. Scan four bar codes from page 7-44 - page 7-45 which corr espond t[...]

7-43 LS 3070 Product Reference Guide: Programming SCAN SUFFIX (V ALUE 1) SCAN PREFIX (V ALUE 2) MA GSTRIPE PREFIX (V ALUE 4) MA GSTRIPE SUFFIX (V ALUE 3)[...]

7-44 LS 3070 Product Reference Guide: Programming 2 4 0 1 3 5[...]

7-45 LS 3070 Product Reference Guide: Programming 7 9 CANCEL 6 8[...]

7-46 LS 3070 Product Reference Guide: Programming Data T ransmission Formats T o select a data transmission format: 1. Scan the SCAN OPTIONS or MAGSTRIPE OPTIONS bar code. 2. Scan the bar code corresponding to the desir ed converted data format. 3. Scan ENTER . 4. If you make a mistake, scan CANCEL , or you wish to erase the last entered format, or[...]

7-47 LS 3070 Product Reference Guide: Programming <PREFIX> <D A T A> <SUFFIX> <D A T A> <SUFFIX> ENTER[...]

7-48 LS 3070 Product Reference Guide: Programming Magstripe Options <A CCT NR> <SUFFIX> <A CCT NR> D A T A AS ON CARD MA GSTRIPE OPTIONS[...]

7-49 LS 3070 Product Reference Guide: Programming <A CCT NR> <SUFFIX> <EXP (MMYY)> <SUFFIX> <A CCT NR> <SUFFIX> <EXP (YYMM)> <SUFFIX> <A CCT NR> <SUFFIX> <NAME)> <SUFFIX> <A CCT NR> <SUFFIX> <EXP (MMYY)> <SUFFIX> <NAME> <SUFFIX>[...]

7-50 LS 3070 Product Reference Guide: Programming <A CCT NR> <SUFFIX> <EXP (YYMM)> <SUFFIX> <NAME> <SUFFIX> <PREFIX> <A CCT NR> <SUFFIX> <PREFIX> <A CCT NR> <SUFFIX> <EXP (YYMM)> <SUFFIX> <PREFIX> <A CCT NR> <SUFFIX> <EXP (MMYY)> <SUFFIX&g[...]

7-51 LS 3070 Product Reference Guide: Programming <PREFIX> <A CCT NR> <PREFIX> <A CCT NR> <SUFFIX> <EXP (MMYY)> <SUFFIX> <PREFIX> <A CCT NR> <SUFFIX> <NAME> <SUFFIX> <PREFIX> <A CCT NR> <SUFFIX> <EXP (YYMM)> <SUFFIX> <NAME> <SUFFIX>[...]

7-52 LS 3070 Product Reference Guide: Programming ERASE ALL FORMA TS ERASE LAST ENTERED FORMA T CANCEL ENTER[...]

7-53 LS 3070 Product Reference Guide: Programming Laser Contr ol T o select a laser-on timeout: 1. Scan the LASER ON TIMEOUT bar code below . 2. Scan two bar codes from the next two pages which corr espond to the desired time. 3. If you make an error , or wish to change your selection, scan CANCEL . LASER ON TIMEOUT[...]

7-54 LS 3070 Product Reference Guide: Programming 2 4 0 1 3 5[...]

7-55 LS 3070 Product Reference Guide: Programming 7 9 CANCEL 6 8[...]

7-56 LS 3070 Product Reference Guide: Programming Baud Rate Set the baud rate for RS-232C transmission. 110 300 600 1200[...]

7-57 LS 3070 Product Reference Guide: Programming . 2400 4800 9600 19200[...]

7-58 LS 3070 Product Reference Guide: Programming P arity Set the type of parity for RS-232C transmission. ODD EVEN MARK SP A CE NONE[...]

7-59 LS 3070 Product Reference Guide: Programming Chec k P arity Select whether or not to check parity for RS-232C transmissions. CHECK P ARITY DO NO T CHECK P ARITY[...]

7-60 LS 3070 Product Reference Guide: Programming Har dware Handshaking Select the type of RS-232C hardwar e handshaking protocol. NONE RTS/CTS[...]

7-61 LS 3070 Product Reference Guide: Programming Software Handshaking Select the type of RS-232C software handshaking pr otocol. NONE A CK/NAK A CK/NAK with ENQ ENQ ONL Y[...]

7-62 LS 3070 Product Reference Guide: Programming Serial Response Timeout T o set a serial (RS-232C) response timeout: 1. Scan the SERIAL RESPONSE TIMEOUT bar code below . 2. Scan two bar codes from the next two pages which r epresent the desired timeout. Y ou must always scan two bar codes. 3. If you make an error , or wish to change your selectio[...]

7-63 LS 3070 Product Reference Guide: Programming 2 4 0 1 3 5[...]

7-64 LS 3070 Product Reference Guide: Programming 7 9 CANCEL 6 8[...]

7-65 LS 3070 Product Reference Guide: Programming Stop Bit Select Select the desired number of stop bits for RS-232C communications. 1 ST OP BIT 2 ST OP BITS[...]

7-66 LS 3070 Product Reference Guide: Programming ASCII Data Format Select either 7-bit or 8-bit ASCII format for RS-232C communications. 7-BIT 8-BIT[...]

7-67 LS 3070 Product Reference Guide: Programming R TS Line State Select the desired option. LINE HIGH LINE LO W[...]

7-68 LS 3070 Product Reference Guide: Programming Inter character Dela y T o set a host communications intercharacter delay: 1. Scan the INTERCHARACTER DELA Y bar code below . 2. Scan two bar codes from the next two pages which r epresent the desired delay . Y ou must always scan two bar codes. 3. If you make an error , or wish to change your selec[...]

7-69 LS 3070 Product Reference Guide: Programming 2 4 0 1 3 5[...]

7-70 LS 3070 Product Reference Guide: Programming 7 9 CANCEL 6 8[...]

7-71 LS 3070 Product Reference Guide: Programming T ransmit Code ID Character Select whether to enable or disable this parameter . TRANSMIT CODE ID CHARA CTER DO NO T TRANSMIT CODE ID CHARA CTER[...]

7-72 LS 3070 Product Reference Guide: Programming T ransmit AIM Code ID Select whether to enable or disable this parameter . This parameter is only valid when T ransmit Code ID Character is enabled. TRANSMIT AIM CODE ID DO NO T TRANSMIT AIM CODE ID[...]

7-73 LS 3070 Product Reference Guide: Programming Ignore Unkno wn Characters Scan the appropriate bar code to enable or disable this parameter . ENABLE DISABLE[...]

7-74 LS 3070 Product Reference Guide: Programming OCIA Cloc k P olarity Select whether the OCIA clock pulse polarity will be rising or falling. RISING F ALLING[...]

7-75 LS 3070 Product Reference Guide: Programming OCIA T ransmit Timeout T o set an OCIA T ransmit T imeout 1. Scan the OCIA TRANSMIT TIMEOUT bar code below . 2. Scan two bar codes from the next two pages which r epresent the desired timeout - Between 3 and 30 seconds. Y ou must always scan two bar codes . For a timeout less than 10 seconds, scan a[...]

7-76 LS 3070 Product Reference Guide: Programming 2 4 0 1 3 5[...]

7-77 LS 3070 Product Reference Guide: Programming 7 9 CANCEL 6 8[...]

7-78 LS 3070 Product Reference Guide: Programming NCR 2152 F ast T ransmit This selects the data transmission speed of the NCR 2152 POS terminal. Depending on the version of NCR 2152, selecting this option may increase the possibility of lost or mis-transmitted data. Scan the appropriate bar code to enable or disable this parameter . ENABLE DISABLE[...]

7-79 LS 3070 Product Reference Guide: Programming IBM 4683 Magstripe Comm unications Select whether to enable or disable IBM 4683/84 magstripe communications. ENABLE DISABLE[...]

7-80 LS 3070 Product Reference Guide: Programming International K eypad Em ulation Select whether to enable or disable this parameter . Used only with IBM A T/XT/PS2. ENABLE DISABLE[...]

7-81 LS 3070 Product Reference Guide: Programming International K eypad Em ulation F ast T ransmit Select whether to enable or disable this parameter . Used only with IBM A T/XT/PS2, and with International Keyboard Emulation enabled. ENABLE DISABLE[...]

7-82 LS 3070 Product Reference Guide: Programming National K eyboar d T ypes Select National T ype for the keyboard. U .S. English French German French International[...]

7-83 LS 3070 Product Reference Guide: Programming Spanish Italian Swedish U .K. English[...]

7-84 LS 3070 Product Reference Guide: Programming Set T ransmission Frequency All Countries Except France T o set the initial channel in all countries except France: 1. Scan the SELECT CHANNEL NUMBER bar code below . 2. Scan two numeric keypad bar codes to set the two-digit channel number , which must be between 02 - 81. SELECT CHANNEL NUMBER (02-8[...]

7-85 LS 3070 Product Reference Guide: Programming 2 4 0 1 3 5[...]

7-86 LS 3070 Product Reference Guide: Programming 7 9 CANCEL 6 8[...]

7-87 LS 3070 Product Reference Guide: Programming W ait f or Host Interface Response Time Programming this parameter overrides the automatically set wait for host timeout value. Conversely , programming a value of zer o enables the automatic wait for host response timeout calculation featur e. T o program the waiting period for the host’s acknowl[...]

7-88 LS 3070 Product Reference Guide: Programming 2 4 0 1 3 5[...]

7-89 LS 3070 Product Reference Guide: Programming 7 9 CANCEL 6 8[...]

7-90 LS 3070 Product Reference Guide: Programming Reserved For Future Use ITEM 1 ENABLE ITEM 1 DISABLE ITEM 2 ENABLE ITEM 2 DISABLE[...]

7-91 LS 3070 Product Reference Guide: Programming ITEM 3 ENABLE ITEM 4 ENABLE ITEM 4 DISABLE ITEM 3 DISABLE[...]

7-92 LS 3070 Product Reference Guide: Programming ITEM 5 ENABLE ITEM 5 DISABLE ITEM 6 ENABLE ITEM 6 DISABLE[...]

7-93 LS 3070 Product Reference Guide: Programming ITEM 7 ENABLE ITEM 8 ENABLE ITEM 8 DISABLE ITEM 7 DISABLE[...]

7-94 LS 3070 Product Reference Guide: Programming APPLICA TIONS V ALUE 0 T O 255 ENTER 3-DIGIT NUMBER FROM NEXT 2 P A GES[...]

7-95 LS 3070 Product Reference Guide: Programming 2 4 0 1 3 5[...]

7-96 LS 3070 Product Reference Guide: Programming 7 9 CANCEL 6 8[...]

7-97 LS 3070 Product Reference Guide: Programming P airing P AIR[...]

8-1 Chapter 8 Keyboard Maps ASCII T able The following values can be assigned as p r efixes or su f fixes for data transmission. Not all options are available on every keyboar d . Refer to your own keyboa r d or Keyboard Identifier Maps on page 8-5 for pertinent keyst r okes. ASCII Full ASCII Code Key- V alue 39 Encode Cha r . st r oke 1000 %U C[...]

8-2 LS 3070 Product Reference Guide: Keyboard Maps ASCII Full ASCII Code Key- V alue 39 Encode Char . stroke 11053 5 5 1054 6 6 1057 7 7 1056 8 8 1057 9 9 1058 /Z : 1059 %F ; 1060 %G < 1061 %H = 1062 %I > 1063 %J ? 1064 %V @ 1065 A A 1066 B B 1067 C C 1068 D D 1069 E E 1070 F F 1071 G G 1072 H H 1073 I I 1074 J J 1075 K K 1076 L L 1077 M M 10[...]

8-3 LS 3070 Product Reference Guide: Keyboard Maps ALT Keys Keystroke 2064 ALT 2 2065 ALT A 2066 ALT B 2067 ALT C 2068 ALT D 2069 ALT E 2070 ALT F 2071 ALT G 2072 ALT H 2073 ALT I 2074 ALT J 2075 ALT K 2076 ALT L 2077 ALT M 2078 ALT N 2079 ALT O 2080 ALT P 2081 ALT Q 2082 ALT R 2083 ALT S 2084 ALT T 2085 ALT U 2086 ALT V 2087 ALT W 2088 ALT X 2089 [...]

8-4 LS 3070 Product Reference Guide: Keyboard Maps Numeric Keypad Keystroke 6042 * 6043 + 6044 Undefined 6045 - 6046 . 6047 / 6048 0 6049 1 6050 2 6051 3 6052 4 6053 5 6054 6 6055 7 6056 8 6057 9 6058 Enter 6059 Num Lock 6060 00 F Keys Keystr oke 5 012 F 12 5013 F 13 5014 F 14 5015 F 15 5016 F 16 5017 F 17 5018 F 18 5019 F 19 5020 F 20 5021 F 21 5[...]

8-5 LS 3070 Product Reference Guide: Keyboard Maps K eyboar d Identifier Maps IBM PC/XT and Clones IBM PC/A T and Clones 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010 7014 7009 7008 7013 7012 7003 7004 7006 7011 7002 7009 7012 7003 7004 7011 7002 7014 7008 5009 5010 5008 5007 5005 5006 5003 5004 5001 5002 7013[...]

8-6 LS 3070 Product Reference Guide: Keyboard Maps IBM 3179 IBM 3180 IBM 319X IBM 347X T elex 122 IBM PS2 and Clones 4001 4002 4003 4004 4005 4006 4007 4008 4009 4010 4011 4012 4013 4014 4015 4016 4017 4018 4019 4020 4021 4022 4023 4024 7009 6059 7001 7013 7008 3001 3002 7002 7006 7003 7019 7011 7005 7015 7017 7012 7018 7016 6042 6043 6044 6055 605[...]

8-7 LS 3070 Product Reference Guide: Keyboard Maps *3001 for IBM 3151 IBM 3151 DEC VT2XX/VT3XX/VT4XX IBM 316X Wyse 50 7014 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010 5011 5012 7010 7007 7001 7008 7011 7012 7003 6042 6043 6044 6047 7009 7002 7019 7005 6055 6056 6057 7006 6059 1013 6052 6053 6054 6045 7015 6049 6051 7004 7017 7016 7018 6048 60[...]

8-8 LS 3070 Product Reference Guide: Keyboard Maps Wyse 60 ANSI K eyboar d Wyse 60 ASCII K eyboar d 5104 5004 5101 5001 5102 5002 5103 5003 5108 5008 5105 5005 5106 5006 5107 5007 5109 5009 5110 5010 5111 5011 5112 5012 5113 5013 5114 5014 5115 5015 5116 5016 3023 7013 7008 7009 5104 5004 5101 5001 5102 5002 5103 5003 5108 5008 5105 5005 5106 5006 [...]

8-9 LS 3070 Product Reference Guide: Keyboard Maps Wyse 60/85/150/185 HP 239X 5104 5004 5101 5001 5102 5002 5013 5003 5108 5008 5105 5005 5106 5006 5107 5007 5109 5009 3023 3025 7005 7003 3024 7009 7008 5111 5011 5112 5012 5120 5020 4001 4002 4003 6058 6046 7015 7018 7016 7017 3026 3027 5110 5010 5113 5013 5114 5014 7013 6045 5117 5017 5118 5018 51[...]

8-10 LS 3070 Product Reference Guide: Keyboard Maps IBM 3178 HP 700/9X SHIFT NORMAL ALT 3023 7013 7011 7002 6080 6 060 6 100 6081 6 061 6 101 6082 6 062 6 102 6083 6 063 6 103 6084 6064 6104 6085 6065 6105 6086 6 066 6 106 6087 6 067 6 107 6088 6068 6108 6089 6 069 6 109 6090 6070 6110 6091 6071 6111 3040 3030 3050 3041 3031 3051 3042 3032 3052 304[...]

8-1 1 LS 3070 Product Reference Guide: Keyboard Maps IBM 3278 SHIFT NORMAL ALT 7011 7002 3040 3030 3050 3041 3031 3051 3042 3032 3052 3043 3033 3053 3044 3034 3054 3045 3035 3055 3046 3036 3056 3047 3037 3057 7021 7020 7022 7031 7030 7032 3001 3023 7013 3002 7012 SHIFT NORMAL ALT[...]

8-12 LS 3070 Product Reference Guide: Keyboard Maps NCR 2151 NCR 2152 27-KEY 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010 5011 5012 5013 5016 5014 5015 7013 5017 5018 5019 5020 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010 5011 7013 5012 5013 5014 5015[...]

8-13 LS 3070 Product Reference Guide: Keyboard Maps NCR 2155 NCR 2157 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010 5011 5012 5013 5014 5015 5016 5017 5018 5019 5020 5021 5022 5023 5024 5025 5026 5027 7013 5028 5029 5030 5031 5032 5033 5034 5035 5035 5037 5038 1046 6060 7019 7013 7008 5031 5032 5033 5034 5035 5036 5037 5038 5039 7009 3022 3018 [...]

8-14 LS 3070 Product Reference Guide: Keyboard Maps NCR 280 NCR 2950 5004 5003 5002 5001 0 78 9 4 5 6 1 2 3 5005 5006 5007 5008 5009 7013 6060 7013 6058 5012 5024 5036 5011 5023 5035 5010 5022 5034 5009 5021 5033 5008 5020 5032 5007 5019 5031 5006 5018 5030 5004 5016 5028 5003 5015 5027 5002 5014 5026 5001 501 3 502 5 500 5 501 7 502 9[...]

8-15 LS 3070 Product Reference Guide: Keyboard Maps NCR 7052 32-KEY NCR 7052 58-KEY 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010 017 1046 5012 1048 5016 1043 5014 1045 5013 5015 5011 5018 5019 7013 5017 (7013 IF DOUBLE KEY) (1048 IF DOUBLE KEY) 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010 5011 0 17 1046 5012 1048 043 5014 1045 5013 5015 5[...]

8-16 LS 3070 Product Reference Guide: Keyboard Maps IBM 3683/3684 35-KEY Calculator Style IBM 3683/3684 35-KEY Phone Style 78 9 4 56 12 3 0 5001 5002 5003 5004 5005 5006 5007 5022 5008 5009 5010 5011 5012 5013 5023 5014 5015 5016 7013 5017 5018 5019 5020 5021 5024 12 3 45 6 78 9 0 5001 5002 5003 5004 5005 5006 5007 5022 5008 5009 5010 5011 5012 501[...]

8-17 LS 3070 Product Reference Guide: Keyboard Maps IBM 3683/3684 48-KEY Calculator Style IBM 3683/3684 48-KEY Phone Style 789 4 56 12 3 0 • 5001 5029 5030 5031 5012 5002 5027 5006 5008 5032 5003 5028 5007 5009 5013 5004 5025 5022 5010 5033 5005 5011 5034 5035 5036 5014 5037 5019 5015 5017 5020 5016 5018 5021 7013 5026 5024 12 3 4 56 78 9 0 • 5[...]

8-18 LS 3070 Product Reference Guide: Keyboard Maps IBM 3683 116-KEY IBM 3653 5005 5004 5003 5018 5002 5001 5005 5004 5003 5018 5002 5001 5043 5042 5041 5040 5039 5038 5048 5047 5046 5045 5044 5009 5053 5052 5051 5050 5049 5007 5059 5058 5057 5056 5055 5054 5065 5064 5063 5062 5061 5060 5071 5070 5069 5068 5067 5066 5077 5076 5075 5074 5073 5072 50[...]

Index-1 A Accessories . . . . . . . . . . . . . . . . . . . . . . . . .4-5 ASCII table. . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 B Base/charger unit . . . . . . . . . . . . . . . . . . . .1-4 Battery Changing battery packs . . . . . . . . . . . 4-2 Charging . . . . . . . . . . . . . . . . . . . . . . .2-3 LED indications . . . . . . . [...]

Index-2 LS 3070 Product Reference Guide: Index Baud rate . . . . . . . . . . . . . . . . . . . . . . 7-56 Check parity . . . . . . . . . . . . . . . . . . . 7-59 Code lengths . . . . . . . . . . . . . . . . . . . 7-22 Code type . . . . . . . . . . . . . . . . . . . . . 7-17 Data transmission formats . . . . . . . 7-46 Decode options . . . . . . . .[...]

Index-3 LS 3070 Product Reference Guide: Index Transmission Range . . . . . . . . . . . . . . . . . . 3-4 U Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1[...]

Thank you for your input—W e v alue your comments. W e’ d like to kno w what you think about this Manual. Please take a moment to fill out this questionaire and fax this form to: (516) 738-3318, or mail to: Symbol T echnologies, Inc. One Symbol Plaza M/S B-4 Holtsville, NY 11742-1300 Attn: T echnical Publications Manager IMPOR T ANT : If you n[...]