Toshiba A40 Series manual

T OSHIBA Satellite A40 Series Port able Personal Computer User ’ s Manual[...]

Copyright © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the informa- tion contained herein. TOSHIBA Satellite A40 Series Portable Personal Computer User’s Manual [...]

FCC information Product Name : Satellite A40 Model number : PSA40 FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference [...]

FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 . This device may not cause harmful interference. 2 . This device must accept any interference received, including interference that may cause undesired operation. Cont act Address: TOSHIBA America Information Systems, Inc. 974[...]

Modem warning notice Conformity St atement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an uncon[...]

Jap an regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made. If more than two redial attempts are made, t[...]

Type of service Your modem is designed to be used on standard-device telephone lines. Connec- tion to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to state tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you[...]

Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent[...]

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termina- tion on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the[...]

Notes for use of this device in New Zealand ❑ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only[...]

❑ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a ) a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network. (b) caller identification information (which occurs between the first a[...]

General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork. The T[...]

Optical disc drive safety instructions NOTE: Be sure to check the international precautions at the end of this section. TEAC CD-RW/DVD-ROM DW-224E CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever requ[...]

DVD Multi DV-W22E CAUTIONS: 1. The DVD Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location. 2. Use of controls, adjustments or the performance of procedures other tha[...]

TOSHIBA DVD-ROM SD-C2612 CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location. 2. Use of controls, adjustments or the performance of procedures othe[...]

DVD-R/-RW SD-R6112 CAUTIONS: 1. The DVD-R/-RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location. 2. Use of controls, adjustments or the performance of procedures other th[...]

CD-RW/DVD-ROM SD-R2412 CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures ot[...]

HIT ACHI DVD-ROM GDR-8082N CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location. 2. Use of controls, adjustments or the performance of procedures ot[...]

DVD±RW GWA-4040N CAUTIONS: 1. The DVD±RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location. 2. Use of controls, adjustments or the performance of procedures other than [...]

Pioneer DVD±RW DVR-K12D CAUTIONS: 1. The DVD±RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location. 2. Use of controls, adjustments or the performance of procedures othe[...]

Panasonic DVD Multi UJ-811B CAUTIONS: 1. The DVD Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location. 2. Use of controls, adjustments or the performance of procedures[...]

CD-RW/DVD-ROM UJDA750 CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures oth[...]

International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To preve[...]

OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE[...]

xxv T able of Content s Preface Manual contents ........................................................................... xxxiii Conventions .................................................................................. xxxiv Abbreviations ................................................................................... xxxiv Icons ........[...]

xxvi Slots .................................................................................................. 1 - 7 Multimedia .......................................................................................... 1 - 7 Communications ................................................................................. 1 - 8 Security ..............[...]

xxvii Connecting the AC adaptor .............................................................. 3 - 5 Opening the display .......................................................................... 3 - 6 Turning on the power ....................................................................... 3 - 7 Starting up for the first time ..................[...]

xxviii CD /D V Ds .......................................................................................... 4-16 Diskettes .......................................................................................... 4-17 Sound System .................................................................................. 4-17 Volume control ..............[...]

xxix Chapter 6 P ower and P ower-Up Modes Power conditions ................................................................................ 6 - 1 Power indicators ................................................................................ 6 - 2 Battery indicators .............................................................................. 6 [...]

xxx Removing an SD card ......................................................................... 8 - 5 SD card care ...................................................................................... 8 - 6 Memory expansion ............................................................................ 8 - 6 Installing memory module ...............[...]

xxxi Modem ............................................................................................. 9-25 Standby/Hibernation ......................................................................... 9-27 L AN .................................................................................................. 9-27 Wireless LAN ...................[...]

xxxii[...]

xxxiii Preface Congratulations on your purchase of the TOSHIBA Satellite A40 computer. This powerful, notebook computer is designed to provide years of reliable, high- performance computing. This manual tells how to set up and begin using your TOSHIBA Satellite A40 computer. It also provides detailed information on configuring your computer, basic [...]

xxxiv User's Manual Chapter 6, Power and Power-Up Mode s , gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Password s , explains how to configure the computer using the HW Setup program. It also tells how to set a password. Chapter 8, Optional Device s , describes the optional hardware availabl[...]

xxxv Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign ( + ). For example, Ctrl + C means you must hold down Ctrl and at the same time press C . If three keys are used, hold down the first two and at the same time press the third. ABC When pr[...]

xxxvi User's Manual[...]

xxxvii General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury, damage to the computer or impaired performance. Be certain to read the general precautions below and to note the caution[...]

User's Manual xxxviii PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system. Computer operation[...]

xxxix The cautions on use of a Satellite A40 series computer . 1. Cleaning of the dust accumulated on the cooling vent of the computer. CAUTION : When you use your computer in a dusty area, the dusts accumulate on a cooling vent at the under side of your computer. The accumulated dusts cause insufficient heat dissipation. Clean the dusts off with v[...]

User's Manual xl Open the keyboard brace CAUTION: Memory module and the work of the replacement of the internal modem etc. detach keyboard brace, bases such as speakers and Power buttons become baring. Never touch substrates such as speakers and Power buttons of baring. It causes the breakdown when touching. Open the keyboard brace S PEAKERS O[...]

I NTRODUCTION Chapter 1 Introduction Equipment checklist .......................................................................... 1 - 1 Hardware ............................................................................................ 1 - 1 Software ............................................................................................. 1[...]

I NTRODUCTION[...]

1-1 I NTRODUCTION Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not prein- stalled by TOSHIBA. Equipment checklist Carefully unpack your[...]

1-2 User's Manual I NTRODUCTION • TOSHIBA Power Saver • TOSHIBA Console • Online manual • TOSHIBA Config Free • TOSHIBA Touch and Launch • TOSHIBA PC Diagrotic Tool ❑ Documentation: • Satellite A40 User's Manual • Microsoft Windows XP manual package • Instruction Manual for Safety & Comfort • End User License Agr[...]

1-3 I NTRODUCTION Mobile Intel ® Pentium ® 4 processor which incorporates a 512KB level 2 cache memory. Mobile Intel ® Pentium ® 4 processor 2.66GHz supporting Hyperthreading Technology(*1) Mobile Intel ® Pentium ® 4 processor 2.88GHz supporting Hyperthreading Technology(*1) Mobile Intel ® Pentium ® 4 processor 3.06GHz supporting Hyperthrea[...]

1-4 User's Manual I NTRODUCTION Because it is universal, it can receive a range of AC voltage from 100 to 240 volts; however, the output current varies among different models. Using the wrong model can damage your computer. See the AC adaptor section in Chapter 2, The Grand Tour . Disks Hard disk drive Available in four sizes. • 7.94 GB (30.[...]

1-5 I NTRODUCTION • CD-ROM XA Mode 2 (Form1, Form2) • Enhanced CD (CD-EXTRA) • CD-G (Audio CD only) • Addressing Method 2 DVD-R/-RW drive Some models are equipped with a full- size DVD-R/-RW drive module that lets you record data to rewritable CD/ DVDs as well as run either 12cm (4.72") or 8cm (3.15") CDs/12cm(4.72") DVDs wit[...]

1-6 User's Manual I NTRODUCTION DVD± R W drive Some models are equipped with a full- size DVD±RW drive (DVD Dual drive) module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It w[...]

1-7 I NTRODUCTION Features Pointing device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer. Ports Parallel Some models are equipped with a parallel port for parallel printer or other parallel device (ECP compatible).Note that some models are not equipped with this port. External monitor 15[...]

1-8 User's Manual I NTRODUCTION Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to Appendix E . The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connect- ing to a telephone line. It is preinstalled as a standard devi[...]

1-9 I NTRODUCTION Security Security lock slot Connects an optional security lock to anchor the computer to a desk or other large object. Software Operating System Windows XP Home Edition/Professional Edition operating system and TOSHIBA Utilities and drivers preinstalled on the hard disk. Refer to the Software section at the front of this chapter. [...]

1-10 User's Manual I NTRODUCTION System automatic This feature automatically shuts down the system in Standby/Hibernation standby mode or Hibernation mode when there is no input or hardware access for a time specified. You can specify the time and select either System Standby or System Hibernate in the System standby and System hibernation ite[...]

1-11 I NTRODUCTION Maximum Turns on fan first, then if necessary Performance lowers CPU processing speed. Performance Uses a combination of fan and lowering the CPU processing speed. Battery optimized Lowers the CPU processing speed first, then if necessary turns on the fan. Hibernation This feature lets you turn off the power without exiting from [...]

1-12 User's Manual I NTRODUCTION DVD Video Player The DVD Video Player is used to play DVD-Video. It has an on-screen interface and functions. Click Start, point to All Programs, point to InterVideo WinDVD 4, then click InterVideo WinDVD 4. ConfigFree ConfigFree is a suite of utilities to allow easy control of communication device and network [...]

1-13 I NTRODUCTION PC Diagnostic TOSHIBA PC Diagnostic Tool displays the basic in- Tool formation on PC, and the test of built-in devices can also be performed.You can boot TOSHIBA PC Diagnostic Tool form the menu bar as follows. [Start]-[All Programs]-[TOSHIBA]-[Utilities]-[PC Diagnos- tic Tool] Options You can add a number of options to make your[...]

1-14 User's Manual I NTRODUCTION[...]

T HE G RAND T OUR Chapter 2 The Grand T our Front with the display closed ........................................................... 2 - 1 Left side .............................................................................................. 2 - 2 Right side ........................................................................................[...]

T HE G RAND T OUR[...]

T HE G RAND T OUR 2-1 Chapter 2 The Grand T our This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. Figure 2-1 Front of the computer with display close[...]

User's Manual T HE G RAND T OUR 2-2 Lef t side Figure 2-2 shows the computer’s left side. * Some models are not equipped with a SD card slot or a i.LINK (IEEE1394) port. Figure 2-2 The left side of the computer LAN active This indicator glows orange when data is being exchanged indicator (orange) between the computer and the LAN. Link indica[...]

T HE G RAND T OUR 2-3 Right side NOTE: Operation of all functions of all USB devices has not been confirmed. Some functions might not execute properly. i.LINK (IEEE1394) Connect an external device, such as a digital video camera port to this port for high-speed data transfer. You must connect the AC adaptor when you use i.LINK. PC card slot A PC ca[...]

User's Manual T HE G RAND T OUR 2-4 Fixed Optical The computer is configured with a full-size optical media media drive drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") disks without using an adaptor. Refer to the Fixed Optical media drive section in this chapter for technical specifications on each drive and to Ch[...]

T HE G RAND T OUR 2-5 Microphone jack A standard 3.5 mm mini microphone jack enables connec- tion of a monaural microphone or other device for audio input. When you connect an external microphone, the internal microphone is automatically disabled. Headphone jack A standard 3.5 mm mini headphone jack enables connec- tion of a stereo headphone (16 oh[...]

User's Manual T HE G RAND T OUR 2-6 Universal Two Universal Serial Bus ports are on the back side. Serial Bus The port comply with the USB 2.0 standard, which (USB 2.0) ports enables data transfer speed 40 times faster than the USB 1.1 standard. (The ports also support USB 1.1.) Also two ports are on the left side. Security lock A security cab[...]

T HE G RAND T OUR 2-7 Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. Figure 2-5 The underside of the computer Battery release Slide this latch to release the battery pack for removal. latch For detailed information on removing the battery packs, refer to Chapter 6, Power [...]

User's Manual T HE G RAND T OUR 2-8 Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the display to the right of the computer and lift up. Position the display at a comfortable viewing angle. Figure 2-6 The front with the display open Disp[...]

T HE G RAND T OUR 2-9 System indicators Audio/Video Previous button: Plays the previous track/chapter/ control buttons* data. Play/pause button: Begins or pauses play. Stop button: Halts play. Next button: Plays the next track/chapter/data. Refer to Chapter 4, Operating Basics . * Audio/Video control buttons are provided with some models. NOTE: If [...]

User's Manual T HE G RAND T OUR 2-10 Battery The Battery indicator shows the condition of the battery’s charge: Green indicates full charge, orange indicates battery charging and flashing orange indicates a low battery charge. Refer to Chapter 6, Power and Power- Up Modes . Built-in HDD The Built-in HDD indicator glows green when the compute[...]

T HE G RAND T OUR 2-11 When the CapsLock indicator glows the keyboard is in all-caps mode. Figure 2-9 CapsLock indicator Caps Lock This indicator glows green when the alphabet keys are locked in uppercase. USB diskette drive A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes. It connects to the USB port. Figure 2-10 U[...]

User's Manual T HE G RAND T OUR 2-12 Eject button When a diskette is fully seated in the drive, the eject button pops out. To remove a diskette, push in the eject button and the diskette pops out partially for removal. CAUTION: Check the Disk-In-Use indicator when you use the diskette drive. Do not press the eject button or turn off the comput[...]

T HE G RAND T OUR 2-13 Fixed optical media drive W rit able discs This section describes the types of writable CD/DVD discs. Check the specifica- tions for your drive to for the type of discs it can write. Use Drag'n Drop CD+DVD to write compact discs. Refer to Chapter 4, Operating Basics . CDs ❑ CD-R discs can be written only once. The reco[...]

User's Manual T HE G RAND T OUR 2-14 DVD-ROM drive The full- size DVD-ROM drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. NOTE: The read speed is slower at the center of a disc and faster at the outer edge. DVD read 8 speed (maximum) CD read[...]

T HE G RAND T OUR 2-15 DVD Multi drive The full-size DVD Multi drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. NOTE : The read speed is slower at the center of a disc and faster at the outer edge. DVD read 8 speed (maximum) DVD-R write 2 speed DV[...]

User's Manual T HE G RAND T OUR 2-16 AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region. To recharge the battery, simp[...]

G ETTING S TARTED Chapter 3 Getting S t arted Setting up your work space .............................................................. 3 - 1 General conditions .............................................................................. 3 - 2 Placement of the computer ................................................................. 3 - 2 Seatin[...]

G ETTING S TARTED[...]

3-1 G ETTING S TARTED Chapter 3 Getting S t arted This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort . This guide, which is included with the computer, expl[...]

User's Manual G ETTING S TARTED 3-2 ❑ Seating and posture ❑ Lighting ❑ Work habits General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ❑ Make sure there is adequate space around the computer for proper ventilation. ❑ Make sure th[...]

3-3 G ETTING S TARTED ❑ Allow adequate space behind the computer to let you freely adjust the display. The display should be angled to reduce glare and maximize visibility. ❑ If you use a paper holder, set it at about the same height and distance as the computer. Seating and posture The height of your chair in relation to the computer and keybo[...]

User's Manual G ETTING S TARTED 3-4 ❑ Adjust the back of your chair so it supports the lower curve of your spine. ❑ Sit straight so that your knees, hips and elbows form approximately 90 degree angles when you work. Do not slump forward or lean back too far. Lighting Proper lighting can improve legibility of the display and reduce eye stra[...]

3-5 G ETTING S TARTED A number of books are available on ergonomics and repetitive strain injury or repetitive stress syndrome. For more information on these topics or for pointers on exercises for such stress points as hands and wrists, please check with your library or book vendor. Also refer to the computer’s Instruction Manual for Safety &[...]

User's Manual G ETTING S TARTED 3-6 1 . Connect the power cord to the AC adaptor. Figure 3-2 Connecting the power cord to the AC adaptor 2 . Connect the AC adaptor’s DC output plug to the DC IN 15V input port on the back of the computer. Figure 3-3 Connecting the adaptor to the computer 3 . Plug the power cord into a live wall outlet. The Ba[...]

3-7 G ETTING S TARTED 2 . Lift the display panel up and adjust it to the best viewing angle for you. CAUTION: Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer. NOTE: When you open the display, hold it with both hands and lift up slowly. Figure 3-4 Opening the display[...]

User's Manual G ETTING S TARTED 3-8 3 . Press and hold the computer’s power button for two or three seconds. Figure 3-5 Turning on the power S t arting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. Durin[...]

3-9 G ETTING S TARTED 3 . Click start then click Turn Off Computer . From the Turn Off Com- puter menu select Turn Off . 4 . Turn off the power to any peripheral devices. CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Hibernation mode The hibernation feature saves the contents [...]

User's Manual G ETTING S TARTED 3-10 Starting Hibernation NOTE: You can also enable Hibernation by pressing Fn + F4 . See Chapter 5, The Keyboard , for details. To enter Hibernation mode, follow the steps below. 1 . Click Start . 2 . Select Turn Off Computer . 3 . Open the Turn Off Computer dialog box. Hibernate is not displayed. 4 . Press the[...]

3-11 G ETTING S TARTED Data save in hibernation mode When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the Built-IN HDD indicator will light. After you turn off the computer and memory is saved to the hard disk, turn off the power to any peripheral devices. C[...]

User's Manual G ETTING S TARTED 3-12 4. If you carry the computer on board an aircraft or into a hospital, be sure to shut down the computer in hiberna- tion mode or in shutdown mode to avoid radio signal interference. Benefits of standby The standby feature provides the following benefits: ❑ Restores the previous working environment more ra[...]

3-13 G ETTING S TARTED NOTES: 1. When the computer is shut down in standby mode, the power indicator flashes orange. 2. If you are operating the computer on battery power, you can lengthen the operating time by shutting down in hibernation mode. Standby mode consumes more power. Standby limitations Standby will not function under the following cond[...]

User's Manual G ETTING S TARTED 3-14 Restoring the preinst alled sof tware from the Product Recovery DVD-ROM If preinstalled files are damaged, use the Product Recovery DVD-ROM to restore them. To restore the operating system and all preinstalled software, follow the steps below. CAUTION: When you reinstall the Windows operating system, the ha[...]

O PERATING B ASICS Chapter 4 Operating Basics Using the Touch Pad ......................................................................... 4 - 1 Using the USB diskette drive ............................................................ 4 - 2 Connecting 3 1/2" diskette drive ......................................................... 4 - 2 Discon[...]

O PERATING B ASICS Connecting ....................................................................................... 4-21 Disconnecting ................................................................................... 4-22 Wireless LAN .................................................................................... 4-22 Security ............[...]

O PERATING B ASICS 4-1 Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad, the external diskette drive, optical media drives, Audio/video controls, Sound System, the internal modem, the wireless communication and LAN. It also provides tips on caring for your computer and on heat dispersal. Us[...]

User's Manual O PERATING B ASICS 4-2 Drag and drop 1 . Hold down the left control button and move the cursor to drag the item you want to move. 2 . Lift your finger to drop the item where you want it. Scroll Vertical: Move your finger up or down the right edge of the Touch Pad. Horizontal: Move your finger left or right along the bottom edge o[...]

O PERATING B ASICS 4-3 Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1 . Wait for the indicator light to go out to make sure all diskette activity has stopped. CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing [...]

User's Manual O PERATING B ASICS 4-4 Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1 . a. When the power is on, press the eject button to open the drawer slightly. Figure 4-3 Pressing the eject button b. Pressing the eject button will not open the drawer when the drive’s power is off. If the power is [...]

O PERATING B ASICS 4-5 2 . Pinch the drawer gently and pull until it is fully opened. Figure 4-5 Pulling the drawer open 3 . Lay the CD/DVD, label side up, in the drawer. Figure 4-6 Inserting a CD/DVD NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DV[...]

User's Manual O PERATING B ASICS 4-6 CAUTIONS: 1. Do not touch the laser lens. Doing so could cause misalignment. 2. Do not keep foreign matter from entering the drive. Check the back edge of the tray to make sure it carries no debris before closing the drive. 4 . Press gently at the center of the CD/DVD until you feel it click into place. The[...]

O PERATING B ASICS 4-7 Audio/Video controls CAUTIONS: 1. When the drawer pops open slightly, wait a moment to make sure the CD/DVD has stopped spinning before pulling the drawer fully open. 2. Turn off the power before you use the eject hole. If the CD/DVD is spinning when you open the drawer, the CD/DVD could fly off the spindle and cause injury. [...]

User's Manual O PERATING B ASICS 4-8 Play/Pause and Stop buttons A single button on a rocker controls the Play/Pause and Stop functions. Press on the icon to select the desired function. Play/Pause Press the icon to begin or pause play. Stop Press the icon to stop play. Controls for CD/DVD and Digit al Audio CD/DVD control Os is running and yo[...]

O PERATING B ASICS 4-9 Before writing or rewriting Please observe the following points when you write or rewrite the data. ❑ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW[...]

User's Manual O PERATING B ASICS 4-10 Writing CD/DVDs on DVD±RW drive (DVD Dual drive) You can use the DVD±RW drive to write data to either CD-R/RW or DVD-R/-RW/+R/+RW discs. The following applications for writing are supplied on CD-ROM: Drag’n Drop CD+DVD, licensed by Easy Systems Japan Ltd., and DigiOn Inc., InterVideo WinDVD Creator 2 P[...]

O PERATING B ASICS 4-11 Writing CD/DVDs on DVD-R/-RW drive Writing CD/DVDs on DVD-R/-RW drive You can use the DVD-R/-RW drive to write data to either CD-R/RW or DVD-R/-RW discs. The following applications for writing are supplied on CD-ROM: Drag’n Drop CD+DVD, licensed by Easy Systems Japan Ltd., and DigiOn Inc., InterVideo WinDVD Creator 2 Plati[...]

User's Manual O PERATING B ASICS 4-12 Writing CD/DVDs on DVD Multi drive You can use the DVD Multi drive to write data to either CD-R/RW or DVD-R/-RW/- RAM discs. The following applications for writing are supplied on CD-ROM: Drag’n Drop CD+DVD, licensed by Easy Systems Japan Ltd., and DigiOn Inc., InterVideo WinDVD Creator 2 Platinum, which[...]

4-13 O PERATING B ASICS Writing CD/DVDs on DVD Multi drive CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-R: DVD Specifications for Recordable Disc for Gen- eral Version 2.0 TAIYOYUDEN CO., LTD. PIONEER VIDEO CORPORATION MITSUBISHI CHEMICAL CO[...]

User's Manual O PERATING B ASICS 4-14 ❑ Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/-RW discs. ❑ You cannot overwrite data that has been previously written to a DVD-RW disc. ❑ You cannot partially delete any data written to a DVD-RW disc. ❑ Data written to a CD-R/DVD-R disc cannot be deleted ei[...]

O PERATING B ASICS 4-15 ❑ Write from the computer's HDD to the CD/DVD. Do not try to write from shared devices such as a LAN server or any other network device. Drag’n Drop CD+DVD Note the following limitations when you use Drag’n Drop CD+DVD: ❑ DVD-Video cannot be created using Drag’n Drop CD+DVD. ❑ DVD-Audio cannot be created usi[...]

User's Manual O PERATING B ASICS 4-16 Dat a verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1 . Right-click Data BOX and select Options to display the DATA DISC Option window. 2 . Mark the Record and Verify check box and select Byte compare . 3 . Click the OK[...]

O PERATING B ASICS 4-17 Diskettes 1 . Store your diskettes in the container they came in to protect them and keep them clean. If a diskette is dirty, do not use cleaning fluid. Clean it with a soft damp cloth. 2 . Do not slide back the diskette’s protective metal covering or touch the diskette’s magnetic surface. Fingerprints may prevent the di[...]

User's Manual O PERATING B ASICS 4-18 1 . Click Start , point to All Programs , point to Accessories , point to Enter- tain ment and click Volume Control . 2 . Click Properties, check the Microphone checkbox and click OK . 3 . Click Options and select Advanced Controls . 4 . Click Advanced . 5 . Check the MIC Boost checkbox and click Close . S[...]

O PERATING B ASICS 4-19 If you want to a more effect for the power management, you can select another mode, the High Power Savings which can save the power than the Normal Power Savings. To select it, follow the steps below. 1 . Clicked the Power Management tab. 2 . Select the High Power Savings in the Power Mode pull-down list. 3 . Input a time in[...]

User's Manual O PERATING B ASICS 4-20 2 . The Region Selection icon will appear in the Windows Task Bar. Figure 4-9 The Region Selection icon 3 . Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to th[...]

O PERATING B ASICS 4-21 Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location l[...]

User's Manual O PERATING B ASICS 4-22 CAUTIONS: 1. In case of a lightning storm, unplug the modem cable from the telephone jack. 2. Do not connect the modem to a digital telephone line. A digital line will damage the modem. 1 . Plug one end of the modular cable into the modem jack. 2 . Plug the other end of the modular cable into a telephone j[...]

O PERATING B ASICS 4-23 ❑ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6Mbit/s. (Revision A and G, Revision B/G, A/B/G combo type) ❑ Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2 and 1Mbit/s. (Revision B) ❑ Automatic Transmit Rate Select mechanism in the transmi[...]

User's Manual O PERATING B ASICS 4-24 Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communi- cation functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireles[...]

O PERATING B ASICS 4-25 Connecting LAN cable To connect the LAN cable, follow the steps below. CAUTIONS: 1. Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up. 2. Do not connect any other cable to [...]

User's Manual O PERATING B ASICS 4-26 Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. CAUTION: Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1 . Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2 . Disconnect the cabl[...]

O PERATING B ASICS 4-27 ❑ If a CD/DVD is in the drive, remove it. Also make sure the drawer is securely closed. ❑ Turn off the power to the computer. ❑ Disconnect the AC adaptor and all peripherals before moving the computer. ❑ Close the display. Do not pick up the computer by its display panel. ❑ Close all port covers. ❑ Use the carryi[...]

User's Manual O PERATING B ASICS 4-28[...]

T HE K EYBOARD Chapter 5 The Keyboard Typewriter keys ................................................................................. 5 - 1 F1 … F12 function keys ..................................................................... 5 - 2 Soft keys: Fn key combinati ons ........................................................ 5 - 2 Emulating ke[...]

T HE K EYBOARD[...]

5-1 T HE K EYBOARD Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s key- board layout your computer is conf[...]

User's Manual 5-2 T HE K EYBOARD F1 … F12 function keys The function keys, not to be confused with Fn , are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked [...]

5-3 T HE K EYBOARD Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard. Since the keyboard of a portable compu[...]

User's Manual 5-4 T HE K EYBOARD Hot keys Hot keys ( Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon. Instant security: Press Fn + F1 t[...]

5-5 T HE K EYBOARD Standby: When you press Fn + F3 , the computer enters Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future. Hibernation: When you press Fn + F4 , the computer enters Hibernation. To avoid entering Hibernation unexpectedly, a [...]

User's Manual 5-6 T HE K EYBOARD LCD Display Brightness: Pressing Fn + F7 increases the display brightness in increments. When you press these hot keys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Screen brightness item of the Basic Setup tab in Power Saver. NOTE: Display[...]

5-7 T HE K EYBOARD Windows special keys The keyboard provides two keys that have special functions in Windows : one activates the start menu and the other has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button. Keyp ad overlay Your computer’s key[...]

User's Manual 5-8 T HE K EYBOARD Numeric mode To turn on the Numeric mode, press Fn + F11 . The Numeric mode F11 indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay T emporarily using normal keyboard (overlay on) While using the overlay, [...]

5-9 T HE K EYBOARD T emporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1 . Press and hold down Fn . 2 . Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric [...]

User's Manual 5-10 T HE K EYBOARD[...]

P OWER AND P OWER -U P M ODES Chapter 6 Power and Power-Up Modes Power conditions ................................................................................ 6 - 1 Power indicators ................................................................................ 6 - 2 Battery indicators ..........................................................[...]

P OWER AND P OWER -U P M ODES[...]

P OWER AND P OWER -U P M ODES 6-1 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The compute[...]

6-2 User's Manual P OWER AND P OWER -U P M ODES Table 6-1 Power conditions continued Power on Power off (no operation) A C Battery • Operates adaptor charge is • LED: Battery off no t above low DC IN 15V off connected battery trigger point Battery • Operates charge is • L E D : Battery below low flashes orange battery DC IN 15V off tri[...]

P OWER AND P OWER -U P M ODES 6-3 NOTE: If the battery becomes too hot while it is being charged, the charge will stop and the battery indicator will go out. When the battery’s temperature falls to a normal range, charge will resume. This occurs whether the computer’s power is on or off. DC IN 15V indicator Check the DC IN 15V indicator to dete[...]

6-4 User's Manual P OWER AND P OWER -U P M ODES Battery p ack When the AC adaptor is not connected, the computer’s main power source is a removable lithium-ion battery pack, also referred to in this manual as the battery pack. You can purchase additional battery packs for extended use of the computer away from an AC power source. Before you [...]

P OWER AND P OWER -U P M ODES 6-5 **** RTC battery is low or CMOS checksum is inconsistent **** Press [F1] key to set Date/Time. CAUTION: The computer’s RTC battery is a nickel metal hydride battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or[...]

6-6 User's Manual P OWER AND P OWER -U P M ODES 2 . Never try to disassemble, repair or otherwise tamper with a battery pack. The battery pack will overheat and ignite. Leakage of caustic alkaline solution or other electrolytic substances will cause fire or injury, possibly resulting in death or serious injury. 3 . Never short-circuit the batt[...]

P OWER AND P OWER -U P M ODES 6-7 Care and use of the battery pack 2 . Immediately turn off the power, disconnect the universal AC adaptor and remove the battery if any of the following events are observed in the battery pack: offensive or unusual odor, excessive heat, discoloration or deformation. Never use the computer again until it has been che[...]

6-8 User's Manual P OWER AND P OWER -U P M ODES 7 . Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor. Never remove the battery pack while the computer is in Suspend or Standby mode. Data will be lost. Note 1 . Never remove the battery pack while the Wake-up on LAN function is enabled[...]

P OWER AND P OWER -U P M ODES 6-9 Time The following table shows the approximate time required to fully charge a dis- charged battery. Charging time (hours) Battery type Power on Power off Battery pack 8400mAh 7 to 20 or longer about 3.5 RTC battery 8 Doesn ’ t charge NOTES: 1. The charging time when the computer is on is affected by ambient temp[...]

6-10 User's Manual P OWER AND P OWER -U P M ODES 3 . Charge the battery until the Battery indicator glows green. Repeat these steps two or three times until the battery recovers normal capacity. NOTE: Leaving the AC adaptor connected will shorten battery life. At least once a month, run the computer on battery power until the battery is fully [...]

P OWER AND P OWER -U P M ODES 6-11 Care and use of the battery pack • Monitor Power off • HDD Power off ❑ How often and how long you use the hard disk and the diskette drive. ❑ How much charge the battery contained to begin with. ❑ How you use optional devices, such as a PC card, to which the battery supplies power. ❑ Enabling Standby m[...]

6-12 User's Manual P OWER AND P OWER -U P M ODES 4 . Connect the AC adaptor to the computer and the power cord to a power outlet. The DC IN 15V indicator should glow green, and the Battery indicator should glow orange to indicate that the battery pack is being charged. If the DC IN 15V indicator does not glow, power is not being supplied. Chec[...]

P OWER AND P OWER -U P M ODES 6-13 3. In Hibernation mode, data will be lost if you remove the battery and disconnect the universal AC adaptor before the save is completed. Wait for the Built-in HDD indicator to go out. 4. Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of th[...]

6-14 User's Manual P OWER AND P OWER -U P M ODES Inst alling the battery pack To install a battery, follow the steps below. CAUTIONS: 1. The battery pack is a lithium-ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries r[...]

P OWER AND P OWER -U P M ODES 6-15 S t arting the computer by p assword To start up the computer with the user password, follow these steps: 1 . Turn on the power as described in Chapter 3, Getting Started . The following message appears: Password = NOTE: At this point, the hotkeys Fn + F1 to F5 do not work. They will function after you enter the p[...]

6-16 User's Manual P OWER AND P OWER -U P M ODES Panel power on/off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in Standby or Hibernation mode but not in boot mode. NOTE: If the panel power off function is enabled and you use Shut down Windows, do [...]

HW S ETUP AND P ASSWORDS Chapter 7 HW Setup and Passwords HW Setup ........................................................................................... 7 - 1 Accessing HW Setup ......................................................................... 7 - 1 HW Setup window ......................................................................[...]

HW S ETUP AND P ASSWORDS[...]

7-1 HW S ETUP AND P ASSWORDS Chapter 7 HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for Display, CPU, Boot Priority, Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer. NOTE: If the su[...]

User's Manual 7-2 HW S ETUP AND P ASSWORDS General This window displays the BIOS version and contains two buttons: Default and About . Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Password User Password This option allows you to set or reset the[...]

7-3 HW S ETUP AND P ASSWORDS If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! To delete a user password: 1 . Select Not Registered to display the following prompt: Enter Password: 2 . Enter the currently registered password. The character string you enter is displayed as a string of asterisks. Enter P[...]

User's Manual 7-4 HW S ETUP AND P ASSWORDS NOTE: It is a good idea to create more than one Key FD in case a Key FD is damaged or lost. To create a Key FD follow the steps below. 1 . Turn off the computer’s power. 2 . Connect the diskette drive to a USB port on the computer. 3 . Set a diskette’s write-protect tab to the write enable positio[...]

7-5 HW S ETUP AND P ASSWORDS Parallel Port Mode The options in this tab are ECP and Standard Bi-directional . ECP Sets the port type to Extended Capabilities Port (ECP). For most printers, the port should be set to ECP . (Default) Standard This setting should be used with some other parallel Bi-directional devices. Display This tab lets you customi[...]

User's Manual 7-6 HW S ETUP AND P ASSWORDS HT Technology This tab is available only on the models with the CPU that supports Hyper- Threading Technology (HTT). You can enable or disable the HTT feature (includ- ing control for PM when enabling it) using this tab. Enabled with PM* Select this option to enable the HTT feature with PM activated. [...]

7-7 HW S ETUP AND P ASSWORDS CD-ROM −> −> −> −> −> LAN −> −> −> −> −> FDD −> −> −> −> −> HDD The computer looks for bootable files in the following order: CD-ROM, LAN, diskette drive and HDD. You can override the settings and manually select a boot device by pressing one of [...]

User's Manual 7-8 HW S ETUP AND P ASSWORDS 3 . Use the left/right cursor keys to highlight the boot device you want and press Enter . NOTES: 1. If a supervisor password is set, the menu above does not appear when you use the user password to start the computer. 2. The selection method above does not change the boot priority settings in HW Setu[...]

7-9 HW S ETUP AND P ASSWORDS NOTE: The Wake-up on LAN function consumes power even when the system is off. Leave the universal AC adaptor connected while using this feature. Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the in[...]

User's Manual 7-10 HW S ETUP AND P ASSWORDS Supervisor p assword Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. The path to the readme file is C:Program FilesTOSHIBAWindows UtilitiesSVPWTool . In the SVPWTool directory, open the readme.htm file.[...]

O PTIONAL D EVICES Chapter 8 Optional Devices PC cards ............................................................................................. 8 - 2 Inserting a PC card ............................................................................. 8 - 2 Removing a PC card ........................................................................[...]

O PTIONAL D EVICES[...]

8-1 O PTIONAL D EVICES Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ❑ PC cards ❑ SD cards ❑ Memory expansion Power devices ❑ Battery pack ❑ Univ[...]

User's Manual 8-2 O PTIONAL D EVICES PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC card[...]

8-3 O PTIONAL D EVICES 3 . Check the configuration in the HW Setup window to make sure it is appropri- ate for your card. After installing the card, refer to the card’s documentation and check the configura- tion in Windows to make sure it is appropriate for your card. Removing a PC card To remove the PC card, follow the steps below. 1 . Click th[...]

User's Manual 8-4 O PTIONAL D EVICES SD cards The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory. The cards have a high leve[...]

8-5 O PTIONAL D EVICES SD cards 2 . Press gently to ensure a firm connection. Figure 8-3 Inserting an SD card CAUTION: Make sure the SD card is oriented properly before you insert it. Removing an SD card To remove an SD card, follow the steps below. 1 . Open the Safely Remove Hardware icon on the system tray and disable the SD card. 2 . Push in the[...]

User's Manual 8-6 O PTIONAL D EVICES CAUTIONS: 1. Make sure the SD card indicator is out before you remove the card or turn off the computer’s power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card. 2. Do not remove an SD card while the computer is in Standby or Hiber[...]

8-7 O PTIONAL D EVICES CAUTIONS: 1. Refer to General Precautions for the attention when keyboard brace is removed. 2. Use only memory modules approved by TOSHIBA. 3. Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost. a. The computer is turned on. b. Th[...]

User's Manual 8-8 O PTIONAL D EVICES 5 . Insert a thin object under the rim of the keyboard brace and lift out the brace. Figure 8-5 Removing the keybord brace 6 . Remove two screws securing the keyboard and one screw securing the metal brace. Lift off the metal brace. NOTE: Use a point size 0 Phillips screwdriver. 7 . Lift up the back of the [...]

8-9 O PTIONAL D EVICES Memory expansion 8 . Lift into the left the insulation sheet covering the memory module and secure the sheet with tape to keep it out of your way. CAUTION: Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. NOTE: The slot A is reserved for main memor[...]

User's Manual 8-10 O PTIONAL D EVICES 1 0 . Seat the insulation sheet to cover the module. NOTE: Be sure to check that the insulation sheet is returned to the original position to cover the memory module. 1 1 . Insert tabs on the front of the keyboard into corresponding notches on the computer and seat the keyboard. CAUTION: When seating the k[...]

8-11 O PTIONAL D EVICES CAUTIONS: 1. If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them. 2. Do not touch the connectors on the memory module or on the[...]

User's Manual 8-12 O PTIONAL D EVICES USB diskette drive The 3 1/2" external diskette drive module can be connected to the USB port. For details on connecting the 3 1/2" external diskette drive module, refer to Chapter 4, Operating Basic s . External monitor An external analog monitor can be connected to the external monitor port on [...]

8-13 O PTIONAL D EVICES 4 . Insert the other end of the cable into the printer’s parallel connector. 5 . Fasten the connector to the printer with the clips on the parallel port. 6 . Turn on the printer. 7 . Turn on the computer. 8 . Start the HW Setup program. Refer to Chapter 7, HW Setup and Password s . 9 . Select the Parallel/Printer tab from [...]

User's Manual 8-14 O PTIONAL D EVICES ❑ You may not use any copyrighted video or music data copied from a video camera except for your personal enjoyment. ❑ If you connect/disconnect an i.LINK device to/from another i.LINK device that is currently exchanging data with the computer, data frames might be dropped. ❑ Make sure data transfer [...]

8-15 O PTIONAL D EVICES Security lock Disconnecting 1 . Open the Safely Remove Hardware icon on the Task Bar. 2 . Point to i.LINK (IEEE1394) device and click. 3 . Disconnect the cable from the computer then from the i.LINK device. NOTE: Refer also to the documentation that came with your i.LINK device. Security lock A security lock enables you to a[...]

User's Manual 8-16 O PTIONAL D EVICES[...]

T ROUBLESHOOTING Chapter 9 T roubleshooting Problem solving process ................................................................... 9 - 1 Preliminary checklist .......................................................................... 9 - 1 Analyzing the problem ........................................................................ 9 - 2 Hard[...]

T ROUBLESHOOTING[...]

9-1 T ROUBLESHOOTING Chapter 9 T roubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Re[...]

User's Manual T ROUBLESHOOTING 9-2 ❑ Check that your diskette or CD/DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify t[...]

9-3 T ROUBLESHOOTING ❑ System start-up ❑ Self test ❑ Power ❑ Battery ❑ Password ❑ Keyboard ❑ LCD panel ❑ Hard disk drive ❑ DVD-ROM drive ❑ CD-RW/DVD-ROM drive ❑ DVD-R/-RW drive ❑ DVD Multi drive ❑ DVD ± RW drive (DVD Dual drive) ❑ Diskette drive Hardware and system checklist ❑ PC card ❑ SD card ❑ Pointing device ?[...]

User's Manual T ROUBLESHOOTING 9-4 Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot P[...]

9-5 T ROUBLESHOOTING Overheating power down If the computer’s internal temperature becomes too high, the computer will automati- cally enter Hibernation or Resume mode and shut down. Problem Procedure Computer shuts down Leave the computer off until the DC IN 15V and DC IN 15V indicator stops blinking. indicator blinks orange NOTE: It is recommen[...]

User's Manual T ROUBLESHOOTING 9-6 Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it. If the terminals are soiled, wipe them with cotton or a clean cloth. If the AC adaptor still does not power the com- puter, contact your dealer. Battery If you suspect a problem with the battery, check the DC IN 15V i[...]

9-7 T ROUBLESHOOTING Hardware and system checklist Check the Battery indicator. If it does not glow, let the computer charge the battery for at least 20 minutes. If the Battery indicator glows after 20 minutes, let the battery continue to charge at least another 20 minutes before turning on the computer. If the indicator still does not glow, the ba[...]

User's Manual T ROUBLESHOOTING 9-8 Problem Procedure Some letter keys Check that the numeric keypad overlay is not produce numbers selected. Press Fn + F10 and try typing again. Output to screen Make sure the software you are using is not is garbled remapping the keyboard. Remapping involves reassigning the meaning of each key. See your softwa[...]

9-9 T ROUBLESHOOTING • Follow the steps below when a plastic spring is out of place together with a key- top. 1. Remove the plastic spring from the key-top. Hardware and system checklist P RESS FROM THE UPSIDE P ROJECTING P ART P ROJECTING P ART S PRING[...]

User's Manual T ROUBLESHOOTING 9-10 2. Attach the plastic spring to the keyboard with its flat face downward after confirming the direction. 3. Press from the upside until you hear a click after replacing the key-top to the right position. LCD p anel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup a[...]

9-11 T ROUBLESHOOTING Problems above Refer to your software’s documentation to remain unresolved determine if the software is causing the or other problems difficulty. occur Contact your dealer if the problems continue. Hard disk drive Problem Procedure Computer does not Check if a diskette is in the diskette drive or a boot from hard disk CD-ROM[...]

User's Manual T ROUBLESHOOTING 9-12 DVD-ROM drive For more information, refer to Chapter 4, Operating Basics . Problem Procedure You cannot access Make sure the drive’s drawer is securely a CD/DVD in the drive closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with[...]

9-13 T ROUBLESHOOTING Check the region code on the DVD. It must match that on the DVD-ROM drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour. If problems persist, contact your dealer. CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics . Problem Procedure You cannot access Make sure t[...]

User's Manual T ROUBLESHOOTING 9-14 CD-ROM: CD-DA, CD-Text, Photo CD™ (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), CD-G (Audio CD only), Addressing Method 2 Recordable: CD-R, CD-RW CD Check the region code on the DVD. It must match that on the CD-RW/DVD-ROM drive. Region codes are li[...]

9-15 T ROUBLESHOOTING Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped i[...]

User's Manual T ROUBLESHOOTING 9-16 • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording. • Do not run or start other software during writing. • Do not jar the computer during writing. • Do not connect/ disconnect external devices or install/remove internal cards during w[...]

9-17 T ROUBLESHOOTING Some CD/DVDs The software or hardware configuration may run correctly, but be causing a problem. Make sure the others do not hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video Recordable: DVD-R, DVD-[...]

User's Manual T ROUBLESHOOTING 9-18 DVD±RW drive (DVD Dual drive) For more information, refer to Chapter 4, Operating Basics . Problem Procedure You cannot access Make sure the drive's drawer is securely closed. a CD/DVD in the drive Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It [...]

9-19 T ROUBLESHOOTING Hardware and system checklist Check the region code on the DVD. It must match that on the DVD ± RW drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended [...]

User's Manual T ROUBLESHOOTING 9-20 PC card Refer also to Chapter 8, Optional Devices . Problem Procedure PC card Reseat the PC card to make sure it is error occurs firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer. SD card Ref[...]

9-21 T ROUBLESHOOTING Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to standby Pad operation its normal shape and try again t[...]

User's Manual T ROUBLESHOOTING 9-22 Touch pad is sensitive 1. Open the Control Panel . or blunt. 2. Click the Printers icon and then the Other Hardware icon. 3. Click the Mouse icon. 4. Click the Device Setting tab. 5. Click the Setting button. 6. The Properties for Synaptics Touchpad on PS/2 port screen appears. Double-click Sensitivity in th[...]

9-23 T ROUBLESHOOTING 2. Click the Buttons tab. 3. Set the double-click speed as instructed and click OK . The mouse pointer Try changing the speed setting in the mouse moves too fast or control utility. too slow 1. Open the Control Panel , select the Mouse icon and press Enter . 2. Click the Pointer Options tab. 3. Set the speed as instructed and [...]

User's Manual T ROUBLESHOOTING 9-24 Memory exp ansion Refer also to Chapter 8, Optional Devices , for information on installing memory modules. Problem Procedure Beep sounds. Make sure the memory module installed in the (If slot A, two beeps. expansion slot is compatible with the computer. If slot B, three beeps. If an incompatible module has [...]

9-25 T ROUBLESHOOTING Monitor Refer also to Chapter 8, Optional Devices , and to your monitor’s documentation. Problem Procedure Monitor does not Make sure that the external monitor’s power turn on switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet. No display Try adjusting the contrast and br[...]

User's Manual T ROUBLESHOOTING 9-26 You can also use the ATX command. Refer to Appendix C, AT Commands . You place a call, Make sure the settings are correct in your but a connection communications application. can’t be made After making a call Make sure the tone or pulse selection in your you can’t hear a ring communications application i[...]

9-27 T ROUBLESHOOTING St andby/Hibernation Problem Procedure The system will Is Windows Media™ Player open? The system not enter might not enter Standby/Hibernation, if Windows Standby/Hibernation Media Player is either playing a selection or finished playing a selection. Close Windows Media Player before you select Standby/Hiberna- tion. If prob[...]

User's Manual T ROUBLESHOOTING 9-28 i.LINK (IEEE1394) Problem Procedure i.LINK device does Make sure the cable is securely connected to not function the computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add New Hardware icon. Follow the on-screen [...]

9-29 T ROUBLESHOOTING Printer Refer also to the Parallel printer sections in Chapter 8, Optional Devices , and to the troubleshooting and other relevant sections in your printer and software documentation. Problem Procedure Printer does not Check that the printer is connected to an electric turn on. outlet. Make sure the outlet is supplying power b[...]

User's Manual T ROUBLESHOOTING 9-30 TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for addi- tional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important [...]

9-31 T ROUBLESHOOTING Outside of Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road North Ryde N.S.W. 2113 Sydney Canada TOSHIBA of Canada Ltd. 191 McNabb Street, Markham, Ontario L3R 8H2 China TOSHIBA Computer Systems (Shanghai) Co., Ltd. Bldg. 33, No. 351, Jinzang Road, Pudong New Area, Shanghai, P.R. Ch[...]

User's Manual T ROUBLESHOOTING 9-32[...]

A PPENDIXES Appendixes Appendix A Specifications ............................................................................... A - 1 Appendix B Display Controller and Modes ..................................................... B - 1 Appendix C AT Commands ............................................................................. C - 1 Appendix[...]

A PPENDIXES[...]

A PPENDIX A A-1 Appendix A S pecifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size 337 (w) x 298 (d) x40/46 (h) millimeters (not including parts that extend beyond the main body) Weight 3.5 kilograms, configured with: 15"XGA-TFT, CD-RW/ DVD-ROM drive, Modem, LAN, IEEE1394, Wireless LAN Weigh[...]

A PPENDIX A A-2 User's Manual Built-in Modem Network control unit (NCU) Type of NCU A A Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication Data: Ful l duplex system Fax: Half duplex Communication Data [...]

B-1 A PPENDIX B Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Extended Graphics Array (XGA) and Super Extended Graphics Array Plus (SXGA+) support for the[...]

User's Manual B-2 A PPENDIX B Video modes The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates. Also, if your software supports both grap[...]

B-3 A PPENDIX B Appendix B Table1 Video modes (VGA) continued Video Type Resolution Character L C D C RT Scanning mode matrix colors colors frequency (pels) Vertical (Hz) D VGA 320 × 200 8 × 8 16 of 256K 16 of 256K 70 Grph Pels E VGA 640 × 200 8 × 8 16 of 256K 16 of 256K 70 Grph Pels F VGA 640 × 350 8 × 14 Mono Mono 7 0 Grph Pels 10 VGA 640 ?[...]

User's Manual B-4 A PPENDIX B Table 2 Video modes (XGA) Resolution L C D C RT Vertical colors colors frequency (Hz) 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 256/256K 256/256K 60 (Virtual) 75 85 100 1400 × 1050 256/256K 256/256K 60 (Virtual) 75 8[...]

B-5 A PPENDIX B Appendix B Table 2 Video modes (XGA) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 64K/64K 64K/64K 60 (Virtual) 75 85 100 1400 × 1050 64K/64K 64K/64K 60 (Virtual) 75 85 1600 ?[...]

User's Manual B-6 A PPENDIX B Table 2 Video modes (XGA) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 16M/16M 16M/16M 6 0 (Virtual) 75 85 100 1400 × 1050 16M/16M 16M/16M 6 0 (Virtual) 75[...]

B-7 A PPENDIX B Table 3 Video modes (Super XGA+) Resolution L C D C RT Vertical colors colors frequency (Hz) 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 256/256K 256/256K 60 75 85 100 1400 × 1050 256/256K 256/256K 60 75 85 1600 × 1200 256/256K 256/256K[...]

User's Manual B-8 A PPENDIX B Table 3 Video modes (Super XGA+) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 64K/64K 64K/64K 60 75 85 100 1400 × 1050 64K/64K 64K/64K 60 75 85 1600 × 120[...]

B-9 A PPENDIX B Appendix B Table 3 Video modes (Super XGA+) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 16M/16M 16M/16M 6 0 75 85 100 1400 × 1050 16M/16M 16M/16M 6 0 75 85 1600 × 1200 16M/[...]

User's Manual B-10 A PPENDIX B Display Settings 1 . You cannot move from the [Settings] tab of [Display Properties] to the multi-monitor when you are using the display of the computer and an external CRT display at the same time. ❑ The [Settings] tab is displayed in the following steps; a. Open [Control Panel] , click [Appearance and Themes][...]

B-11 A PPENDIX B ❑ The way to move to multi-monitor a. Press [Ctrl] + [Alt] + [F12] keys to make [Intel(R) 82852/82855 GM/GME Graphics Controller Prope...] displayed. (See FigureB-2) b. Click in the left of [Devices] tab (See FigureB-2), then select [Extended Desktop] . c. Check that the Primary Device is fixed into Note Book (the display of the [...]

User's Manual B-12 A PPENDIX B 2 . Some reproduced DVD picture may not be displayed when the display of the computer and a CRT display are used at the same. Reduce the resolution, use the display of the computer only, use the CRT display only or set display device in the multi-monitor, then play DVD. Please refer to External monitor in the onl[...]

B-13 A PPENDIX B c. The following [Set up] screen is displayed, then remove the check of [Use Hardware Decode Acceleration] (The check of [Use Hardware Color Acceleration] is removed automatically). Figure B-5 Setup d. Click [OK] button(The [Set up] tab closes automatically). 4 . The DVD video overlay is not displayed when the display mode of CRT d[...]

User's Manual B-14 A PPENDIX B 5 . A DVD-reproduced image may not be displayed in correct position when you press Fn + F1 to enter into Instant Security mode while a DVD is playing under WinDVD 4.0, and then move the mouse or press the key to exit Instant Security mode. In this case, close WinDVD 4.0 and open it again, or pres the Stop button [...]

C-1 A PPENDIX C Appendix C A T Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn where X is the AT [...]

User's Manual C-2 A PPENDIX C A Answer command This command instructs the modem to go off-hook and answer an incoming call. B n Communication standard setting This command determines the communication standard CCITT or Bell. B0 Selects CCITT V.22 mode when the modem is at 1200 bps. B1 Selects Bell 212A when the modem is at 1200 bps (default). [...]

C-3 A PPENDIX C ; Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. S = n Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. E n Echo command This command controls whether or not the characters [...]

User's Manual C-4 A PPENDIX C L n Monitor speaker volume This command sets speaker volume to low, medium, or high. L0 Low volume. L1 Low volume. (Same as L0 ) L2 Medium volume (default). L3 High volume. Result Codes: OK n=0,1,2,3 ERROR Otherwise Mn Monitor speaker mode This command turns the speaker on or off. M0 The speaker is off. M1 The spe[...]

C-5 A PPENDIX C Result Codes: OK n=0,1 ERROR Otherwise On Return on-line to data mode O0 Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). O1 This command issues a retrain before returning to on-line data mode. O3 This command issues a rate renegotiation before returning to on-line data mode. Re[...]

User's Manual C-6 A PPENDIX C T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. V n DCE response format This command controls whether result codes (including call progress and negotiation progress me[...]

C-7 A PPENDIX C X 5 Enable Enable OK, RING , NO CARRIER, ERROR, NODIAL TONE, BUSY , CONNECT <RA TE>, RRING , NO BONGTONE, DELA YED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and[...]

User's Manual C-8 A PPENDIX C &C0 The state of the carrier from the remote modem is ignored. DCD circuit is always on. &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default). Result Codes: OK n=0,1 ERROR Otherwise & D n DTR control This command interprets how[...]

C-9 A PPENDIX C &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only. &G0 Guard tone disabled (default). &G1 Sets guard [...]

User's Manual C-10 A PPENDIX C &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line. Result [...]

C-11 A PPENDIX C Nn Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. N0 Buffer mode. No error control. N1 Direct mode. N2 MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects. This is also [...]

User's Manual C-12 A PPENDIX C Vn Protocol result code V0 Disable protocol result code appended to DCE speed. V1 Enable protocol result code appended to DCE speed (default). Result Codes: OK n=0,1 ERROR Otherwise % B View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted i[...]

D-1 A PPENDIX D Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connec- tion fails. You can also customize certain AT commands such as the escape [...]

User's Manual D-2 A PPENDIX D S 0 Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command. Range: 0-255 Default: 0 Units: rings S 1 Rin[...]

D-3 A PPENDIX D S 4 Response formatting character (user defined) This register determines the ASCII value used as the line feed charac- ter. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 ( li n e f e ed ) Units: ASCII S 5 Command line editing character (user defined) T[...]

User's Manual D-4 A PPENDIX D S 7 Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (an- swer). In originate mode, the timer is reset upon detection of an answer to[...]

D-5 A PPENDIX D S3 7 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8 7200 bps S37 = 9 9600 bps S37 = 10 12000 bps S37 = 11 14400 bps S37 = 12 16800 bps S37 = 13 19200 bps S37 = 14 21600 bps S37 = 15 24000 bps S37 = 1[...]

User's Manual D-6 A PPENDIX D A T command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description O K 0 Command executed CONNECT 1 Modem connected to line RING 2 A ring signal has been detected NO CARRIER 3 Modem lost carrier signal, or does not detect carrier signal, or does not det[...]

D-7 A PPENDIX D Result Code Numeric Description DELAYED* 2 8 8 Delay is in effect for the dialed number BLACKLISTED* 2 8 9 Dialed number is blacklisted BLACKLIST FULL* 2 9 0 Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error c[...]

User's Manual D-8 A PPENDIX D[...]

E-1 A PPENDIX E Appendix E V .90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary c[...]

User's Manual E-2 A PPENDIX E Table E-1 Result codes for a V.90 connection No. Result code Description 7 0 CONNECT 32000 EC* Connection at 32000 bps 7 2 CONNECT 36000 EC* Connection at 36000 bps 7 4 CONNECT 40000 EC* Connection at 40000 bps 7 6 CONNECT 44000 EC* Connection at 44000 bps 7 8 CONNECT 48000 EC* Connection at 48000 bps 8 0 CONNECT [...]

E-3 A PPENDIX E * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V 4 2 V.42 error control only NoEC N o error control protocol [...]

User's Manual E-4 A PPENDIX E[...]

F-1 A PPENDIX F Appendix F Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Inst alling the internal modem NOTE: The internal modem is preinstalled. The following i[...]

F-2 User's Manual A PPENDIX F 9 . Remove two screws, which you use later to secure the modem board. 1 0 . Connect the modem board cable and seat the modem board. 1 1 . Secure the modem board with two screws removed in step 9. 1 3 . Seat the insulation sheet to cover the modem board. 1 4 . Insert tabs on the front of the keyboard into correspon[...]

F-3 A PPENDIX F 1 4 . Two screws secure the keyboard and one screw secures the metal brace. 1 5 . Seat the keyboard brace and press to secure latches. 1 6 . Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details. Refer to the installation procedures for details. The internal modem i[...]

F-4 User's Manual A PPENDIX F[...]

G-1 A PPENDIX G Appendix G Wireless LAN Card Specifications Form Factor  Mini PCI TypeIII Compatibility  IEEE 802.11 Standard for Wireless LANS Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance.The 'Wi-Fi CERTIFIED' logo is a certification mark of the Wi-Fi Alliance. Network Operating  Microsoft Windows ® Networking Syst[...]

G-2 User's Manual A PPENDIX G R-F Frequency  Band 5GHz (5150-5850 MHz) (Revision A, Turbo Mode)  Band2.4GHz (2400-2483.5 MHz) (Revision B, Revision B, B/G, A/B/G combo type) Modulation  DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK Technique (Revision B, Revision B/G, A/B/G combo type)  OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM-64QAM (Revision A, [...]

G-3 A PPENDIX G 9 2452 10 2457* 1 11 2462 12 2467* 2 13 2472* 2 *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions. that in which these channels can be used. When installing Wireless LAN Cards, the channel configuration is managed as follows: ❑ For wireless clients that operate in a[...]

G-4 User's Manual A PPENDIX G Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID 5150-5850 MHz Note 42 5210 U S only *1 50 5250 U S only *1 58 5290 U S only *1 15 2 5760 U S only *1 16 0 5800 U S only *1 *1: Available Area: US (USA, CANADA) only[...]

H-1 A PPENDIX H Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm 2 Current r[...]

H-2 User's Manual A PPENDIX H The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe. USA and Canada United Kingdom Australia Europe BS approved UL approved CSA approved AS approved Approved by the appropriate agency[...]

A PPENDIX I I -1 Appendix I Part s Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, ODD, communication, mini PCI and indent devices.[...]

User's Manual I-2 A PPENDIX I Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change without notice. *Figures indicate the CPU operating[...]

Glossary-1 G LOSSARY Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP : accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic [...]

Glossary-2 G LOSSARY circuit cards that control external devices, such as video monitors and magnetic tape devices. allocate: To assign a space or function for a specific task. alphanumeric: Keyboard characters including letters, numbers and other symbols, such as punctuation marks or mathematical symbols. alternating current (AC): Electric current[...]

Glossary-3 G LOSSARY ASCII: American Standard Code for Information Interchange. ASCII code is a set of 256 binary codes that represent the most commonly used letters, numbers, and symbols. async : Short for asynchronous. asynchronous: Lacking regular time relationship. As applied to computer communications, asynchronous refers to the method of tran[...]

Glossary-4 G LOSSARY memory, which saves time. The computer has two cache levels. Level one is incorporated into the processor and level two resides in external memory. capacity: The amount of data that can be stored on a magnetic storage device such as a diskette (floppy disk) or hard disk. It is usually described in terms of kilobytes (KB), where[...]

Glossary-5 G LOSSARY computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. configuration: The specific compo- nents in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works. You use the HW Setup program to[...]

Glossary-6 G LOSSARY disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head. disk storage: Storing data on magnetic disk. Data is arranged on concent[...]

Glossary-7 G LOSSARY escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. execute: To interpret and execute an instruction. Extended Capability Port: An industry standard that provides a data [...]

Glossary-8 G LOSSARY hertz: A unit of wave frequency that equals one cycle per second. hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F. host computer: The computer that controls, regulates, and transmits information to a device or another computer. hotkey: The computer’s feature in[...]

Glossary-9 G LOSSARY LSI: Large Scale Integration. 1) A technology that allows the inclusion of up to 100,000 simple logic gates on a single chip. 2) An integrated circuit that uses large scale integration. M main board: See motherboard. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. megahertz: A unit of wave freq[...]

Glossary-10 G LOSSARY O OCR: Optical Character Recognition (reader). A technique or device that uses laser or visible light to identify characters and input them into a storage device. online state: A functional state of a peripheral device when it is ready to receive or transmit data. operating system: A group of programs that controls the basic o[...]

Glossary-11 G LOSSARY parity: 1) The symmetrical relation- ship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even. password: A unique[...]

Glossary-12 G LOSSARY ROM: Read Only Memory : A nonvolatile memory chip manufac- tured to contain information that controls the computer’s basic operation. You cannot access or change information stored in ROM. S SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices. SD cards: Se[...]

Glossary-13 G LOSSARY subpixel: Three elements, one red, one green and blue (RGB), that make up a pixel on the color LCD. The computer sets subpixels indepen- dently, each may emit a different degree of brightness. See also pixel. synchronous: Having a constant time interval between successive bits, characters or events. system disk: A disk that ha[...]

Glossary-14 G LOSSARY[...]

Index-1 I NDEX Index A AC adaptor 1-3, 2-16 DC IN 15V port 2-6 connecting 3-5 universal 1-13 ASCII characters 5-9 Auto power on, See Power B Battery, See also Battery pack charging 6-8 extending life 6-11 indicator 2-10, 6-2 monitoring capacity 6-10 real time clock 1-3, 6-4 safety precautions 6-5 save mode 1-10 types 6-3 Battery pack 1-3, 6-4 locat[...]

Index-2 User's Manual I NDEX Ergonomics lighting 3-4 seating and posture 3-3 work habits 3-4 Expansion memory, See Memory expansion F Fn + Ctrl (enhanced keyboard simulation) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-4 Fn-esse 1-11 Fn + F1 (instant security) 5-4 Fn + F2 (power save mode) 5-4 Fn + F3 (standby) 5-5 Fn + F4 (hibernation) 5-5 Fn [...]

Index-3 I NDEX jack location 2-2 using 4-24 LCD, See Display, Video modes and Monitor external Lock, security, See Security lock M Main battery, See Battery pack Memory 1-3 expansion 1-13, 8-6 installing 8-7 removing 8-10 slots 1-3 video RAM 1-3 Microphone, See sound system, microphone Microprocessor, See Processor Modem 1-8, 4-19 connecting 4-21 d[...]

Index-4 User's Manual I NDEX password 9-7 PC card 9-20 pointing device 9-21 power 9-4 preliminary checklist 9-1 Real time clock 9-28 SD card 9-20 self test 9-4 sound system 9-24 standby/hibernation 9-27 support from TOSHIBA 9-30 system start-up 9-3 Touch Pad 9-21 USB 9-23 Wireless LAN 9-27 Processor 1-2 R Real time clock battery, See Battery R[...]