Português dropdown-ico

Toshiba B-852-R manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Ir para a página of

Manuais similares

Bom manual de uso

As regras impõem ao revendedor a obrigação de fornecer ao comprador o manual com o produto Toshiba B-852-R. A falta de manual ou informações incorretas fornecidas ao consumidor são a base de uma queixa por não conformidade do produto com o contrato. De acordo com a lei, pode anexar o manual em uma outra forma de que em papel, o que é frequentemente utilizado, anexando uma forma gráfica ou manual electrónicoToshiba B-852-R vídeos instrutivos para os usuários. A condição é uma forma legível e compreensível.

O que é a instrução?

A palavra vem do latim "Instructio" ou instruir. Portanto, no manual Toshiba B-852-R você pode encontrar uma descrição das fases do processo. O objetivo do manual é instruir, facilitar o arranque, a utilização do equipamento ou a execução de determinadas tarefas. O manual é uma coleção de informações sobre o objeto / serviço, um guia.

Infelizmente, pequenos usuários tomam o tempo para ler o manual Toshiba B-852-R, e um bom manual não só permite conhecer uma série de funcionalidades adicionais do dispositivo, mas evita a formação da maioria das falhas.

Então, o que deve conter o manual perfeito?

Primeiro, o manual Toshiba B-852-R deve conte:
- dados técnicos do dispositivo Toshiba B-852-R
- nome do fabricante e ano de fabricação do dispositivo Toshiba B-852-R
- instruções de utilização, regulação e manutenção do dispositivo Toshiba B-852-R
- sinais de segurança e certificados que comprovam a conformidade com as normas pertinentes

Por que você não ler manuais?

Normalmente, isso é devido à falta de tempo e à certeza quanto à funcionalidade específica do dispositivo adquirido. Infelizmente, a mesma ligação e o arranque Toshiba B-852-R não são suficientes. O manual contém uma série de orientações sobre funcionalidades específicas, a segurança, os métodos de manutenção (mesmo sobre produtos que devem ser usados), possíveis defeitos Toshiba B-852-R e formas de resolver problemas comuns durante o uso. No final, no manual podemos encontrar as coordenadas do serviço Toshiba na ausência da eficácia das soluções propostas. Atualmente, muito apreciados são manuais na forma de animações interessantes e vídeos de instrução que de uma forma melhor do que o o folheto falam ao usuário. Este tipo de manual é a chance que o usuário percorrer todo o vídeo instrutivo, sem ignorar especificações e descrições técnicas complicadas Toshiba B-852-R, como para a versão papel.

Por que ler manuais?

Primeiro de tudo, contem a resposta sobre a construção, as possibilidades do dispositivo Toshiba B-852-R, uso dos acessórios individuais e uma gama de informações para desfrutar plenamente todos os recursos e facilidades.

Após a compra bem sucedida de um equipamento / dispositivo, é bom ter um momento para se familiarizar com cada parte do manual Toshiba B-852-R. Atualmente, são cuidadosamente preparados e traduzidos para sejam não só compreensíveis para os usuários, mas para cumprir a sua função básica de informação

Índice do manual

  • Página 1

    PRINTED IN JAPAN TOSHIBA Thermal Printer B-852-R SERIES Document No. EO18-33018 Original Mar., 2006 (Revised ) Maintenance Manual[...]

  • Página 2

    EO18-33018 TABLE OF CONTENTS Page 1. UNPACKI NG -------------------------------------------------------------------------------------------- 1- 1 1.1 PROCEDURES --------------------------------------------------------------------------------------------- 1- 1 1.2 CHECKS -------------------------------------------------------------------------------[...]

  • Página 3

    1. UNPACKING EO18-33018 (Revision Date: Sep. 28, 2007 1.1 Procedure 1- 1 1. UNPACKING 1.1 Procedure 1) Open the carton. 2) Unpack the accessories from the carton. 3) Unpack the pads and the printer from the carton. Supply Holder Frame (L) and (R) Supply Holder Base Power Cord Print Head Cleaner Owner’s Manual B-852-R Printer Bottom Pad Supply Hol[...]

  • Página 4

    1. UNPACKING EO18-33018 (Revision Date: Sep. 28, 2007) 1.2 Checks 1- 2 4) Remove the five pieces of tape from the printer. 5) Open the top cover. 6) Remove the one piece of tape. 7) Press down the head block release lever (1) and raise the print head block (2). 8) Remove the print head pad (3). 9) Place the printer on a level surface. 10) Please at[...]

  • Página 5

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.1 OPENING AND REMOVING THE COVERS 2-1 2. MAJOR UNIT REPLACEMENT 2.1 OPENING AND REMOVING THE COVERS 1) Turn the power off. 2) Open the top cover. 3) Remove the three B-4x6 screws to detach the side cover R. NOTE: After removing the screws, unhook the side cover R from portion A b y lifting and moving it toward[...]

  • Página 6

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.1 OPENING AND REMOVING THE COVERS 2-2 NOTE: After removing the screws, unhook th e side cover L from portion B by lif ting and moving it toward the front of the printer . 5) Disconnect the operation panel harness from CN13 on the MAIN PC Board. NOTE: Instructions to open the top cover and to detach the side co[...]

  • Página 7

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.3 Replacing the MAIN PC Board 2-3 2.3 Replacing the MAIN PC Board 1) Prior to replacing the MAIN PC board, print out the parameter settings for future reference. 2) Remove the side cover L from the printer. (Refer to Section 2.1.) 3) Remove the three SMW-3x6 screws to detach the rear frame cover. 4) Disconnect[...]

  • Página 8

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.3 Replacing the MAIN PC Board 2-4 4) Remove the two SMW-4x8 screws, SMW-3x6 screw and B-3x6 screw . 5) Disconnect the power harness from CN8 on the MAIN PC board ass’y , then remove the MAIN PC board ass’y from the printer . SMW-3x6 Screw SMW-4x8 Screw B-3x6 Screw MAIN PC Board Ass’ y MAIN PC Board Ass?[...]

  • Página 9

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.3 Replacing the MAIN PC Board 2-5 6) Remove the two B-3x6 screws and the two SMW-3x6 screws, then remove the MAIN PC board from the MAIN PCB support frame. 7) Replace the MAIN PC board with a new one, and reassemble in the reverse order of removal. 8) After replacing the MAIN PC board, perform the following op[...]

  • Página 10

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.4 Replacing the Panel PC Board 2-6 2.4 Replacing the Panel PC Board 1) Remove the side cover L from the printer. (Refer to Section 2.1.) 2) Remove the PT-3x8 screw to detach the operation panel ass’y from the side cover L in the direction indicated by the arrow. 3) Disconnect the operation panel harness from[...]

  • Página 11

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.4 Replacing the Panel PC Board 2-7 5) Remove the two PT -3x6 screws and W-4 washers to det ach the panel PC board from the operation panel cover . 6) Replace the panel PC board with a new one, then reassemble in the order removal. 7) T urn the power on, then confirm that the LCD message is displayed properly .[...]

  • Página 12

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.5 Replacing the S tepping Motor 2-8 2.5 Replacing the S tepping Motor 1) Remove the side cover L and MAIN PC board ass’y from the printer . (Refer to Sections 2.1 and 2.3.) 2) Remove the two SMW-3x6 screws to det ach the PCB support plate from the printer . 3) Remove the two SM-4x8 screws to detach the stepp[...]

  • Página 13

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.5 Replacing the S tepping Motor 2-9 NOTE: Apply FLOIL to the stepping m otor ’s pulley and the m otor gear when reassembling the stepping motor . Motor Gea r Pulley Stepping Moto r[...]

  • Página 14

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.6 Replacing the Head Up Sensor , Slit Sens or (Rewind/Feed) and Ribbon Motor (Rewind/Feed) 2-10 2.6 Replacing the Head Up Sensor , Slit Sensor (Rewind/Feed) and Ribbon Motor (Rewind/Feed) Prior to replacing the sensors or ribbon motor , perform the following operations. 1) Open the top cover . (Refer to Sectio[...]

  • Página 15

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.6 Replacing the Head Up Sensor , Slit Sens or (Rewind/Feed) and Ribbon Motor (Rewind/Feed) 2-1 1 3) Replace the head up sensor with a new one, then reassemble in the reverse order of removal. 4) Perform a test print to print to confirm that the printer works properly . NOTE: Be careful not to damage the slit s[...]

  • Página 16

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.6 Replacing the Head Up Sensor , Slit Sens or (Rewind/Feed) and Ribbon Motor (Rewind/Feed) 2-12 5) Push and release the hook A, then release the hook B to remove the slit sensor from the sensor holder . 6) Replace the slit sensor with a new one, then reassemble in the reverse order of removal. 7) Perform a tes[...]

  • Página 17

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.6 Replacing the Head Up Sensor , Slit Sens or (Rewind/Feed) and Ribbon Motor (Rewind/Feed) 2-13 NOTES: 1. Af ter replacing the ribbon motor , refer to Section System Mode Manual to perform a Maintenance Counter clear . 2. Secure the ribbon motors while inserting a 0.1 mm-thick p aper (or folded backing paper) [...]

  • Página 18

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.7 Replacing the Platen 2-14 Print Head Head Block Release Lever 2.7 Replacing the Platen 1) Prior to replacing the platen, print out the maintenance counter for future reference. 2) Open the top cover , and raise the print head block by pressing down the head block release lever . 3) While pulling the top part[...]

  • Página 19

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.7 Replacing the Platen 2-15 6) Replace the platen with a new one, then reassemble in the reverse order of removal. NOTE: When reassem bling, confirm the orient ation of the shaft holder . (See the picture below .) 7) Perform a test print to confirm that the printer works properly . Shaft Holder Platen[...]

  • Página 20

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.8 REPLACING THE MEDIA SENSOR 2-16 2.8 REPLACING THE MEDIA SENSOR 2.8.1 Feed Gap Sensor (TR) and Black Mark Sensor (Upper Side) 1) Open the top cover and raise the print head block. 2) Pull up the two tabs of the sensor case cap to remove it from the sensor block. 3) Remove the feed gap sensor (TR) and black ma[...]

  • Página 21

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.8 REPLACING THE MEDIA SENSOR 2-17 2.8.2 Feed Gap Sensor (LED) and Black Mark Sensor (Lower Side) 1) Remove the platen holder R, platen holder L, platen, and strip plate from the printer 2) Remove the SMW-4x8 screw to det ach the front cover from the printer . 3) Unhook the two springs. 4) Remove the two SMW-3x[...]

  • Página 22

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.8 REPLACING THE MEDIA SENSOR 2-18 NOTES: 1. When reassembling the sensor case cap, fit the hooks of the sensor case into portion A of the sensor case cap. 2. When reassembling the sensors, align the pins on the sensor case with the holes of the sensors. 3. Connect the harness including the green wire to the bl[...]

  • Página 23

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.9 REPLACING THE PRINT HEAD 2-19 2.9 REPLACING THE PRINT HEAD 1) Open the top cover and raise the print head block. 2) Push the print head ass’y to the right side, lift it in the direction of the arrow, and release it from the print head fixing pin. 3) Disconnect the print head harnesses from the three connec[...]

  • Página 24

    2. MAJOR UNIT REPLACEMENT EO18-33018 (Revision Date: May 21, 2007) 2.10 Replacing the PS Unit and Reactor 2-20 2.10 Replacing the PS Unit and Reactor NOTE: The reactor is installed in the B-852-TS22-QP-R and B-852-TS22-CN models. 1) Remove the side covers L, side cover R and MAIN PC Board from the printer. 2) Raise the print head block. 3) Remove t[...]

  • Página 25

    2. MAJOR UNIT REPLACEMENT EO18-33018 (Revision Date: May 21, 2007) 2.10 Replacing the PS Unit and Reactor 2-21 5) Disconnect the PSU harness from CN4 on the PS unit. 6) Disconnect the harnesses from CN1 on the PS unit. For the QP and CN models, disconnect the harness from CN2, too. 7) Remove the two SMW-4x8 screws to detach the PS unit from the PSU[...]

  • Página 26

    2. MAJOR UNIT REPLACEMENT EO18-33018 2.10 Replacing the PS Unit and Reactor 2-22 9) Replace the PS unit or reactor with a new one, then reassemble in the reverse order of removal. WARNING! Pass the reactor harness and inlet harness through the cut in the PS unit frame. Care must be taken not to pinch the harnesses in the frame. Failure to do this m[...]

  • Página 27

    3. PERIODIC MAINTENANCE PROCE DURE EO18-33018 3. PERIODIC MAINTENANCE PROCEDURE 3-1 3. PERIODIC MAINTENANCE PROCEDURE All machines are generally delivered in their best condition. To maintain optimal operating condition and help gain maximum performance and life of machines, we would recommend you to conduct periodic maintenance. Doing this is also[...]

  • Página 28

    3. PERIODIC M AINTENANCE PROCEDURE EO18-33018 3. PERI ODIC MAI NTENANCE PROCEDURE 3-2 3) Clean the print head elements with the T O SHI BA T EC-approved print head cleaner . (Please instruct your cust om er s to clean them daily .) 4) Remov e any paper dust and glue of t he label. W ipe off moving rang e of t he m edia sensor . Print Head Cleaner P[...]

  • Página 29

    3. PERIODIC M AINTENANCE PROCEDURE EO18-33018 3. PERI ODIC MAI NTENANCE PROCEDURE 3-3 5. Apply FLOIL G-488 to t he cut ter unit using a soft cloth. 6. Clean the Cutter Blade with a cotton swab moistened with absolute ethyl alcohol. 7. Confir m t hat the problem occur s as r epor t ed, and then tak e corrective action. 8. Replace the f ollowing part[...]

  • Página 30

    3. PERIODIC MAINTENANCE PROCE DURE EO18-33018 3. PERIODIC MAINTENANCE PROCEDURE 3-4 1 1. Clean the outside of the printer . 12. Fill out a report form. Hand it to the manager and obtain a signature.[...]

  • Página 31

    4. TROUBLESHOOTING EO18-33018 4. TROUBLESHOOTING 4- 1 4. TROUBLESHOOTING Problems Cause Solution Power does not turn ON. 1. Input voltage to the printer is not within the rated voltage. 2. Output voltage from the printer is not within the rated voltage. 3. No voltage to the MAIN PC board. 4. Failure of MAIN PC board. Replace the power cable or powe[...]

  • Página 32

    4. TROUBLESHOOTING EO18-33018 4. TROUBLESHOOTING 4- 2 Problems Cause Solution Media feed failure 1. Media is not set properly. 2. Poor media quality 3. Improper adjustment of the feed gap sensor or black mark sensor. 4. Threshold is improper. 5. Failure of the feed gap sensor or black mark sensor 6. The cutter mechanism is not installed properly. 7[...]